Commercial Energy Saver Gas
STANDARD
9001
1
Millivolt Models
Standard Equipment Features:
Bradford White is ISO registered
to the 9001-standard.
■ Non-CFC foam insulation.
■ Vitraglas®lined tank.
■ Factory installed Hydrojet®Sediment
Reduction System.
■ Factory installed dielectric fittings.
■ Flue damper.
■ Continuous pilot-ignition.
■ Magnesium anode rods.
■ Hand hole cleanout.
■ Millivolt controls.
■ Brass drain valve.
■ T&P relief valve installed.
■ Millivolt models are available from 125,000
to 270,000 BTUH (36.6 KW to 79.1 KW)
■ Three year limited warranty.
■ One year limited parts warranty.
■ Design certified by CSA International
(formerly AGA and CGA)
■ All models listed with California Energy
Commission.
Where Applicable
Optional Features:
■ NSF construction available.
■ ASME code available on all models
above 200,000 BTUH (58.6KW)
MANUFACTURED UNDER ONE OR MORE OF THE FOLLOWING U.S. PATENTS:
7,063,133 B2; 5,954,492; 5,954,492; 5,761,379; 5,943,984; 5,081,696; 5,988,117;
6,142,216; 5,199,385; 5,574,822; 5,372,185; 5,485,879; 5,277,171; (B1)5,341,770;
5,660,165; 5,596,952; 5,682,666; 4,904,428; 5,023,031; 5,000,893; 4,669,448;
4,829,983; 4,808,356; 5,115,767; 5,092,519; 5,052,346; 4,416,222; 4,628,184;
4,861,968; 4,672,919; Re. 34,534. OTHER U.S. AND FOREIGN PATENT
APPLICATIONS PENDING. CURRENT CANADIAN PATENTS: 1,272,914; 1,280,043;
1,289,832; 2,045,862; 2,112,515; 2,108,186; 2,107,012; 2,092,105.5.
Standard Equipment Features:
Brass drain valve.
Non-CFC foam insulation.
Vitraglas®lined tank—B
tanks are protected from the corrosive effects of hot water by
an exclusive ceramic porcelain-like coating. The Bradford
hite high silica Vitraglas
W
surface for our water heater tanks, which must withstand the
wearing effects of high volume and high temperature hot
ater.
w
®
radford White water heater
ining provides a tough interior
l
Factory installed Hydrojet®Sediment
Reduction System—cold inlet sediment reduction
device made of stainless steel for increased durability. Helps
prevent sediment build up in tank.
Factory installed dielectric fittings—all heaters
equipped with special water heater nipples for longer heater
life. No special dielectric fittings to buy.
Flue damper—automatic flue damper reduces stand-by
loss, saving money and fuel.
Continuous pilot ignition—continuous pilot ignition
eliminates the need for an external electric source which is
used on other commercial water heaters.
Magnesium anode rods—employed to provide an
extra measure of corrosion prevention for longer life.
T&P relief valve installed.
Three year limited warranty—
investment in a quality glass lined water heater. If the tank
eaks for reasons of faulty materials, workmanship, or
l
corrosion within the warranty period, the water heater will be
replaced with a comparable water heater of our manufacture.
Exclusive of all shipping and reinstallation costs.) Some states
(
do not allow limitations on warranties. See complete copy of
the warranty included with the water heater.
protects your
One year limited parts warranty—these quality
components are manufactured for us by industry leaders and
will be replaced in the event of failure during the parts
warranty period (exclusive of shipping and reinstallation
costs.)
Design certified by CSA International
(formerly AGA and CGA)
All models listed with California Energy
Commission.
Optional Features:
NSF construction available.
North Carolina Code Compliant.
Hand hole cleanout—allows inspection of tank
interior and facilitates removal of water heater's principal
deterrent to long life—accumulated lime and sediment
deposits.
Millivolt controls—no external electric source is
required for water heater operation. Adjustable thermostat to
any temperature up to 180°F (82°C). A manual reset Energy
Cut-Off (E.C.O.) shuts off all gas in event of an overheat
condition.
ASME code available on all models above
200,000 BTUH (58.6KW)
Dimensions
H
B
E
C
D
F
COLD
H
OT
T & P
G
A
CLEANOUT
A
H
B
E
D
F
HOT
T & P
G
Millivolt Models
Water Connections
Top and Front
DM75T125
DM80T180, 199, 250
DM100T199, 250
Top Front, Rear
DM100L199, 250, 270
DM100S199, 250
Water Connections
Front and Rear
DM75T160
DM38T155
Sample Specification
The water heater shall be a Bradford White model with a storage capacity of not less than ____________ gallons (____________ liters), a minimum
gas input of ____________ BTUH (KWH), and a minimum recovery of _______ GPH (LPH) at 100°F (56°C). temperature rise. It shall be design
certified by CSA International (formerly AGA and CGA) for 180°F (82°C). application, either with or without a separate storage tank. The tank shall
be lined with Vitraglas®vitreous enamel and shall have a bolted hand hole cleanout. The tank shall have ____________ extruded magnesium anode
rods installed in separate head couplings and extended to within three inches of the bottom. The heater shall be insulated with non-CFC foam
insulation. This water heater shall be equipped with an ASME rated T&P relief valve, a continuous pilot ignition system and flue damper. The entire
installation shall be made in compliance with state and local codes and ordinances.
Dimensions and specifications subject to change without notice in accordance with our policy of continuous product improvement.
ILLIVOLT MODELS
Sales/800-523-2931
Fax/215-641-1670
Technical Support/800-334-3393
Fax/269-795-1089
Warranty/800-531-2111
Fax/269-795-1089
International:
Telephone/215-641-9400
Telefax/215-641-9750
Ambler, PA
888-538-7833
Fax on Demand:
bradfordwhite.comwww.
For U.S. and Canada field service,
contact your professional installer or
local Bradford White sales representative.
Sales/Technical Support
866-690-0961
905-238-0100
Fax/905-238-0105
Mississauga, ON
www.bradfordwhitecanada.com
M
MODEL NUMBER BTU RISE 40° 100° 140° GAL. HT. DIA. CONN. CONN. CONN. CONN. HT. DIA. DIA. DIA. OPEN. STD. ASME
▲
DM-38T-155-3N 155,000 174 368 147 105 38 43 281⁄4 —343⁄4 193⁄8 45⁄8 51 6 11⁄2
DM-75T-125-3N 125,000 174 303 121 86 75 65 281⁄4 671⁄8 541⁄2 34 43⁄4 721⁄4 51
▲
DM-75T-160-3N
DM-80T-180-3N 180,000 231 436 175 124 80 641⁄2 281⁄4 661⁄4 56 191⁄2 43⁄4 723⁄8 61
▲
DM-80T-199-3N
▲
DM-80T-250-3N(A)
▲
DM-
100T-199-3N 199,999 263 485 194 139 98 751⁄2 281⁄4 771⁄4 67 191⁄2 43⁄4 833⁄8 61
▲
DM-
100T-250-3N(A)
▲
DM-
100L-199-3N 199,999 264 485 194 139 100 65 301⁄4 67
▲
DM-
100L-250-3N(A) 250,000 312 606 242 173 100 65 301⁄4 67
▲
DM-
100L-270-3N(A)* 270,000 332 655 262 187 100 65 301⁄4 67
▲
DM-
100S-199-3N 199,999 264 485 194 139 100 727⁄8 281⁄4 75
▲
DM-
100S-250-3N(A) 250,000 312 606 242 173 100 727⁄8 281⁄4 75
▲
MODEL NUMBER INPUT RISE 22° 56° 78° LITERS HT. DIA. CONN. CONN. CONN. CONN. HT. DIA. DIA. DIA. OPEN. (KG) (KG)
▲
(LP)
(LP)
(LP)
(LP)
Includes installed T&P Valve and Flue Damper with Continuous Pilot Ignition.
ECOVERY GPH
NAT 1ST HR. STG. C D† E† G
& LP DEL. GAL. CAP. TOP F&R F&R F TOP H WTR. GAS RELIEF
INPUT AT 100°F U.S. A B WTR. HW CW GAS VENT VENT CONN. CONN. VALVE
R
AT DEGREE RISE
160,000 204 378 151 108 75 65 281⁄4 671⁄8 541⁄2 34 43⁄4 721⁄4 61
199,999 250 485 194 139 80 641⁄2 281⁄4 661⁄4 56 191⁄2 43⁄4 723⁄8 61
250,000 298 606 242 173 80 641⁄2 281⁄4 661⁄4 56 191⁄2 43⁄4 723⁄8 61
250,000 311 606 242 173 98 751⁄2 281⁄4 771⁄4 67 191⁄2 43⁄4 833⁄8 61
1ST HR. C D† E† G
DEL. LTR. TOP F&R F&R F TOP H WTR. GAS RELIEF STD ASME
KW AT 56°C STG. A B WTR. HW CW GAS VENT VENT CONN. CONN. VALVE WT. WT.
RECOVERY LPH
AT DEGREE RISE
DIMENSIONS IN INCHES WEIGHT
3⁄43
1
⁄2
1
⁄2
1
⁄2
1
⁄2
1
⁄2
1
⁄2
1
⁄2
1
1
561⁄2 231⁄2
561⁄2 231⁄2
561⁄2 231⁄2
601⁄2
601⁄2
DIMENSIONS IN MILLIMETERS WEIGHT
41⁄2 75 6
41⁄2 75 6
41⁄2 75 6
203⁄4 41⁄2 763⁄4 6
203⁄4 41⁄2 763⁄4 6
1
1
1
1
1
1
1
1
⁄2(T&F)
2(R)
⁄2(T&F)
(R)
2
⁄2(T&F)
2(R)
T&F)
⁄2(
2(R)
⁄2(T&F)
2(R)
⁄4
3⁄43
⁄4
3⁄43
⁄4
3⁄43
⁄4
3⁄43
⁄4
3
⁄4
1 540 590
3⁄43
⁄4 610 —
3
⁄4 1 610 690
3
⁄43⁄4 725 —
3
⁄4 1 725 765
3
⁄4 1 725 765
3
⁄43⁄4 667 —
3
⁄4 1 667 702
DM-38T-155-3N 45.4 659 1391 556 397 144 1092 718 — 883 492 117 1295 152 38 19 19 199 —
DM-75T-125-3N 36.6 659 1147 458 326 284 1651 718 1705 1384 864 121 1835 127 38 19 19 236 —
▲
DM-75T-160-3N
DM-80T-180-3N 52.7 874 1650 662 469 303 1638 718 1683 1422 495 121 1838 152 38 19 19 245 —
▲
DM-80T-199-3N
▲
DM-80T-250-3N(A)
▲
DM-
100T-199-3N 58.6 995 1836 734 526 371 1918 718 1962 1702 495 121 2118 152 38 19 19 277 —
▲
DM-
100T-250-3N(A)
▲
DM-
100L-199-3N 58.6 999 1836 734 526 379 1651 768 1702 1435 597 114 1905 152 19 19 329 —
▲
DM-
100L-250-3N(A) 73.2 1181 2294 916 655 379 1651 768 1702 1435 597 114 1905 152 19 25 329 347
▲
DM-
100L-270-3N(A)* 79.0 1257 2479 992 708 379 1651 768 1702 1435 597 114 1905 152 19 25 329 347
▲
DM-
100S-199-3N 58.6 999 1836 734 526 379 1851 718 1905 1537 527 114 1949 152 19 19 302 —
▲
DM-
100S-250-3N(A) 73.2 1181 2294 916 655 379 1851 718 1905 1537 527 114 1949 152 19 25 302 318
▲
For LP models change suffix “N” to “X”
▲
- 80% Thermal Efficient
(A) - ASME
T - Top Water Connection
F - Front Water Connection
R - Rear Water Connection
* - Available with natural gas only.
(LP)
(LP)
(LP)
46.8 772 1431 572 409 284 1651 718 1705 1384 864 121 1835 152 38 19 19 236 —
58.6 946 1836 734 526 303 1638 718 1683 1422 495 121 1838 152 38 19 19 245 —
73.2 1128 2294 916 655 303 1638 718 1683 1422 495 121 1838 152 38 19 25 245 268
(LP)
73.2 1177 2294 916 655 371 1918 718 1962 1702 495 121 2118 152 38 19 25 277 313
8 (T&F)
3
51(R)
38 (T&F)
1(R)
5
38 (T&F)
51(R)
38 (T&F)
1(R)
5
38 (T&F)
1(R)
5
Energy Saver Series feature Hand Hole Cleanout on all models.
Recoveries and First Hour Delivery Rating are based on Thermal Efficiencies ranging
up to 80%.
150 PSI Working Pressure, 300 PSI Test Pressure.
† Rear connections offered as standard on the "L" and "S" models. DM38T155 also
features rear connections.
438 —
520 —
520 —
540 —
540 —
For LowNOx compliance to meet SCAQMD requirements, place
an “E” following the BTU Input identifier of the model number.
Example: DM-75T-125E-3N
Efficiency in compliance with CSA International (formerly AGA/CGA)
ANSI Z21.10.3 requirements. These models meet or exceed the Thermal
efficiency and standby loss requirements of ASHRAE 90.1b (current
edition).
(LP)
Propane Gas Inputs
75T-160 155,000BTU/H/45.4KW 199/753 366/1385 147/556 105/397
80T-199 190,000BTU/H/55.7KW 240/908 461/1745 184/696 132/500
80T-250 235,000BTU/H/68.9KW 284/1075 570/2157 228/863 163/616
100T-250 235,000BTU/H/68.9KW 297/1124 570/2157 228/863 163/616
All models are design certified by CSA International (formerly AGA and
CGA) for up to 180°F (82°C) application as an Automatic Storage Heater,
and an Automatic Circulating Tank Heater.
As an Automatic Storage Heater, all models are complete self-contained
water heating systems. It needs no separate storage tank, pump, wiring
or elaborate piping network. When equipped with a mixing valve, it will
supply 180
water simultaneously. These models can be used either as a single unit or
in multiples connected in parallel.
°C) sanitizing and 140°F (60°C). general purpose hot
F (82
°
GAL. @ 100
1ST HR. DEL.
°
F RISE/ RECOVERY @ DEGREE RISE
C RISE
°
LITER @ 56
40°F/22°C 100°/56°C 140°/78°C
GPH/LPH
Vitraglas®and Hydrojet®are registered trademarks of Bradford White®Corporation.
©2006 Bradford White Corporation. All rights reserved.
742-B-1106-A Printed in U.S.A.
Loading...