Bradford White ES-3000-2-S-10, ES-3500-1-S-10, ES-3000-1-S-10, ES-3000-5-S-10, ES-3500-4-S-10 Installation Manual And Owner's Manual

ELECTRIC INSTANTANEOUS TANKLESS WATER HEATER

INSTALLATION GUIDE AND OWNERS MANUAL

ELEMENT CARTRIDGE

HEATER MODEL/ORDER REF. CARTRIDGE REF #

RELAY

PART#EX250B-

EX254B

FLOW RESTRICTOR

AERATOR

PART # EX0061-0.5-AER

CONTROL BOARD

EX0183DL-30A for

120V, 277V,

240V, 208V

REPLACEMENT PARTS FOR “Single Point” MODELS

CALL TECHNICAL SERVICE

@ 1-800-334-3393

COMPRESSION

SLEEVE 3/8”

PART # EX68C

COMPRESSION

NUT 3/8”

PART #EX68B

WARNING

BEFORE ATTEMPTING INSTALLATION OF THIS UNIT OR MAKING ANY

ADJUSTMENTS TO T HE UNIT, BE SURE CIRCUIT BREAKER IS OFF

TO PREVENT DANGER OF SERIOUS ELECTRIC SHOCK.

FAILURE TO GROUND THE SYSTEM MAY RESULT IN SERIOUS INJURY OR DEATH

INSTALLER/ CONSUMER RESPONSIBILITIES

READ THIS MANUAL CAREFULLY BEFORE ATTEMPTING TO INSTALL OR
OPERATE THIS WATER HEATING UNIT. IF THE SAFETY RULES ARE NOT

FOLLOWED, THE UNIT WILL NOT OPERATE PROPERLY AND COULD CAUSE

DEATH, SERIOUS BODILY INJURY AND/OR PROPERTY DAMAGE. WARRANTY

OF THIS UNIT WILL DEPEND ON PROPER INSTALLATION AND OPERATION.

THE WARRANTY WILL BE VOID IF THE DESIGN HAS BEEN ALTERED IN ANY WAY

WHATSOEVER. THE MANUFACTURER OF THIS UNIT WILL NOT BE LIABLE

FOR ANY DAMAGES BECAUSE OF FAILURE TO COMPLY WITH THE INSTALLATION

AND OPERATING INSTRUCTIONS OUTLINED ON THE FOLLOWING PAGES.

THE INSTALLATION MUST CONFORM WITH THE INSTRUCTIONS IN THIS

MANUAL AND THE LOCAL CODES, OR IN THE ABSENCE OF LOCAL CODES,

WITH THE LATEST EDITION OF THE NATIONAL ELECTRICAL CODE. THE

NATINOAL ELECTRICAL CODE IS AVAILABLE FROM WRITING

UNDERWRITERS LABORATORIES, 333 PFINGSTEN RD.,

NORTHBROOK, IL. 60062

IF ASSTANCE IS REQUIRED OR ANY QUESTIONS RELATING

TO THE INSTALLATION OR PERFORMANCE OF THIS UNIT ARISE,

PLEASE CONTACT

TECHNICAL SERVICE TOLL FREE:1-800-334-3393.

HAVE THE INFORMATION LISTED BELOW BEFORE CALLING:

MODEL NO.___________SERIAL NO.___________INSTALLATION DATE_____

“SINGLE POINT”

MODELS COVERED:

ES-2400-1-S-10 ES-3000-1-S-10
ES-3000-2-S-10 ES-3000-5-S-10
ES-3500-1-S-10 ES-3500-4-S-10
ES-4100-2-S-10 ES-4100-5-S-10
ES-5500-4-S-10

ES-2400-1-S-10 120V EX610SP
ES-3000-1--S-10 120V EX480SP
ES-3500-1-S-10 120V EX410SP
ES-3000-2-S-10 120V EX1440SP
ES-4100-2-S-10 208V EX1050SP
ES-3500-5-S-10 240V EX1650SP
ES-4100-5-S-10 277V EX1870SP
ES-3000-5-S-10 277V EX2500SP
ES-5500-4-S-10 240V EX1050SP

INSTALL

THIS WAY UP

ONLY !

UP

relay

PLUMBING CONNECTIONS

1) The unit is supplied with 3/8’’ compression fittings. USE THESE: DO NOT
USE THREADED PIPE FITTINGS. DO NOT USE PIPE DOPE OR TEFLON
TAPE ON THIS INSTALLATION. Ensure the inlet filter supplied with this unit
is in place.

2) Ensure that the pipes are correctly aligned with the inlet and
outlet bosses to avoid excessive stress on the heater body molding of the
unit.

NOTE: Run water through the supply pipe to remove all debris from the
pipe before connecting to the unit. Failure to do so could damage the flow
switch.

3) Install isolating valves (shut-off type),or equivalent on both inlet and outlet
pipes. This allows the unit to be isolated for maintenance purposes. (Fig. 2)

4) When all plumbing is complete, inspect the system for water leaks
at all plumbing connections. If a water leak is present take corrective action.
If a water leak is at the compression fitting, slowly tighten compression nut
until the water leaks ceases.
Fully open both inlet and outlet shut-off valves.
Run all hot water outlets fed by this heater one at a time until the water flow
is continuous and free from “gulping” and all visible air pockets.

NOTE:

ALL PLUMBING AND MOUNTING MUST BE COMPLETED

BEFORE PROCEEDING WITH THE

ELECTRICAL HOOK-UP.

TEST THE INSTALLATION FOR LEAKS BEFORE

CONNECTING THE ELECTRICAL SUPPLY.

.

Inlet
filter