BQT BT900-WG, bqt miP9, CSN9, BT900-D, BT900 BT900-BM Installation Manual

Drilling template

• 20mm (0.79”) diameter hole for wire entry

• 2 x 4 mm (0.16”) diameter ho les for mounting screws

• Inner reader di mension is 88mm x 88 mm (3.47 " x 3.47")

• Assemble reader outer dimension is 90mm x 90mm (3.54” x 3.5 4”)

• Reader corne r radius is 4mm (0.16”)

Specifications

Output protocols

Wiegand 26-199 bit, RS485 or custom confi guration (Model
dependent)

BT815-WG/
MiP5/CSN5

BT815-D/D2

BT815

BT815-BM

Power requirement

12V DC

6-18V DC

7-16V DC

Current
consumption

103mA (Avg)

145mA (Peak)

157mA (Avg)

174mA (Peak)

38mA (Avg)

80mA (Peak)

45mA (Avg)

135mA (Peak)

Read range

20-40mm (0.8”-1.6”) at 12V DC de pends on the type of card
used

Operating
temperature

-25’C to +65’C (-13’F to 149’F)

Relative humidity

90% max, operating non-c ondensing

Reader dimensions

Standard: 90mm(L) x 90mm(W) x 27mm(D) (3.54”x3.54”x1.06”)
Slim Line: 90mm(L) x 90mm(W) x 20mm(D) (3. 54”x3.54”x0.79”)

Status LED

Green & Red

Audible tone

Internal and external buzzer control

Colour finish

Charcoal & Ivory

IP rating

IP65

Information o btained in this docume nt is subject to change w ithout notice.

For further technical inf ormation, visit our webs ite at www.bqtsolutions.com or email

techsupport@ bqtsolutions.com.

Alternatively contact us at one of our global locations

AUSTRALIA & PACIFIC

BQT Solutions (Australia) Pty Limited
Level 1, 82 Waterloo Road
Macquarie Park, NSW 2113, Australia
Phone: [phone]
Fax: [phone]
Email: [e-mail]

EUROPE AND MIDD LE EAST

BQT Solutions (UK) Limited
Regal House, 70 London Road
Twickenham, TW1 3QS
United Kingdom
Phone: [phone]
Fax: [phone]
Email: [e-mail]

GREATER ASIA

BQT Solutions Singapore Office
Mediapolis
71 Ayer Rajah Crescent #03-03
Singapore 139951
Phone: [phone]
Fax: [phone]
Email: [e-mail]

Copyright © 2012 BQT S olutions Limi ted. BQT Solutio ns and the BQ T solutions l ogo are register ed trademarks of BQT Solutions (Australia) Pty Ltd.

Wiring diagram

Note:

• A shielded cable is recommended to be used. The shield is connected to controller 0V reference

• Maximum wieg and data cable length: 150 meters (500 feet)

• Buzzer and LED are activated when buzzer and LED line go below 2.5V.

• RS485 lines and Relay lines are only for optional use.

• Some models have additional wires/connectors which are not specified in the diagram above. These wires are for other

requirements. DO NOT connect them unless specified from BQT Solutions or a BQT authorized distributor. Any damage
caused by incorrect connection will void the warranty

• Terminate or insulate all un-used wires

Regulatory Information

C-Tick: This device is C-Tick complied.
CE: The device has passed all relevant tests and obtained CE approval.
FCC: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1) this device

may not cause harmful interference and 2) this device must accept any interference received, including interference that
may cause undesired operation of the device.
Warning: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part
15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and use d in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-Consult the dealer or an experienced radio/TV technician for help.
Any changes or modifications not expressively approved by BQT Solutions could void the user’s authority to operate this
equipment.

5

Series

INSTALLATION GUIDE

Version4.1

Installation

Remove the cover by holding the unit by the rim and pushing the reader
out with your thumbs.

Note: DO NOT use a screw driver or other implement to remove cover

If necessary, drill holes in the wall for the mounting screws or mounting
box on which the reader unit will be placed. (Use the Drilling Template
provided overleaf).

1. Place the controller and power supply cable through the grommet hole.

2. Drill the holes as indicated in the template.

Note: Make sure that you don't drill through the cable.

Wire connection
Note:

Power to the unit is provided from the listed control unit or from a
separately UL listed 12V DC power-limited, access control power source.
DO NOT supply power during installation.

Wiring methods shall be in accordance with the Electrical wiring regulation
in your country / region.

Check your circuit diagram for the colour coding of the circuit wiring. The
reader can be damaged beyond repair if the wiring is connected incorrectly.
This will void the warranty.

1. Connect the 0V wire to the power 0V line;

Note: The 0V line of all power supplies must be connected to a common 0V reference

point.

2. Connect the Wiegand data wires;

3. Connect the Buzzer and LED wires;

4. Connect 12V DC wire;

5. Place reader on the wall (Make sure the wires are not crushed. This

will void the warranty if damage occurs)

6. Insert and hand tighten the screws;

7. Check that the reader is level before tightening the screws;

Note: Excessive tightening of screws may deform the casing, resulting in a damaged

unit. This will void the warranty.

8. Turn on the 12V DC power to power up reader.

9. Allow 5 – 10 seconds for reader to finish initialization (depends on the

application). Make sure reader is functioning correctly according to
the application specification.

External Use

• Make sure the wire bundle to the reader has an IP rating of at least IP65

Handling

• Handle the reader with care. DO NOT damage or drop unit before

installation. This will void the warranty.

• If the case is damaged, the reader may not be to the specified IP rating.

Replace the reader if the case is damaged.

Maintenance

• Once installed the reader requires no maintenance.

Troubleshooting

Problem

Troubleshoo ting steps

Power on rea der – reader does

not start up

1. Check connections

2. Check the voltage a t the reader

3. Check the current capability of the power

supply

Power on rea der – reader keeps

beeping

1. Check buzzer line

2. Check the voltage a t the reader

3. Check the current capability of the power

supply

Power on rea der – LED stays
green

1. Check LED line

Present a card to reader – a beep

is heard but reade r does not
output any data

1. Check whether the card has data encoded

2. Check the wiegand connection to controlle r

3. Check the voltage level on wiegand data li nes

Present a card to reader – no

response from reader

1. Try a known working card

2. Check if the reader requires to be configured

with a confi guration car d

If the proble m still pers ists, please contact your distributor for technical support.

Warranty

Unless specified otherwise, the Company warrants to the Customer that’
BQT Solutions Branded Products’ (excluding third party products and
software) are covered by a return to base warranty on defects in materials
and workmanship affecting normal use for a period of the Warranty offered
under the Standard Terms and Conditions of Sale from BQT invoice date
(‘Standard Warranty’)

This standard warranty does not cover damage, fault, failure or malfunction
due to external causes including; accident, misuse, problems with electrical
power, servicing not authorised by the Company, usage and/or storage
and/or installation not in accordance with Product instructions, failure to
perform required preventative maintenance, normal wear and tear, act of
God, fire, flood, war, any violent or similar occurrence; any attempt by any
person other than Company personnel or any person authorised by the
Company to repair or support the Products and problems caused by use of
parts and components not supplied by the Company. The standard warranty
does not cover any items that are in one or more of the following categories:
software; external devices; accessories or parts added to the product after
the product has been shipped from BQT Solutions.

During the warranty, period beginning on the invoice date, the Company will
repair or replace faulty products (at its absolute discretion) returned to its’
factory. The Customer must prepay shipping and transportation costs and
insure the shipment or accept the risk of loss or damage during such
transportation.

The Customer shall be solely responsible for determining suitability for use
and the Company will, in no event, be liable in this respect. This standard
warranty is given in place of all warranties, conditions, terms, undertakings
and obligations implied by statute, common law, trade usage, and course of
dealing or otherwise including warranties or conditions of merchantability,
fitness for purpose, satisfactory quality and / or compliance with description,
all of which are hereby excluded to the fullest extent permitted by law.

Drilling template

• 20mm (0.79”) diameter hole for wire entry

• 2 x 4 mm (0.16”) diameter ho les for mounting screws

• Minimum reade r dimensions are 140mm x 45 mm (5.51" x 1.77")

Specifications

Output protocols

Wiegand 26-199 bit, RS485 or custom confi guration (Model
dependent)

BT900-WG/
miP9 / CSN9

BT900-D

BT900

BT900-BM

Power requirement

12V DC

6-18V DC

7-16V DC

Current
consumption

103mA (Avg)

145mA (Peak)

135mA (Avg)

155mA (Peak)

38mA (Avg)

80mA (Peak)

45mA (Avg)

135mA (Peak)

Read range

20-40mm (0.8”-1.6”) at 12V DC de pends on the type of card
used

Operating
temperature

-25’C to +65’C (-13’F to 149’F)

Relative humidity

90% max, operating non-c ondensing

Reader dimensions

140mm(L) x 45mm(W) x 32mm(D) (5.51”x1.77”x1.26”)

Status LED

Green & Red

Audible tone

Internal and external buzzer control

Colour finish

Two toned – Silver & Charcoal

IP rating

IP65

Information o btained in this docume nt is subject to change w ithout not ice.

For further technical inf ormation, visit our webs ite at www.bqtsolutions.com or email

techsupport@ bqtsolutions.com

.

Alternatively contact us at one of our global locations

AUSTRALIA & PACIFIC

BQT Solutions (Australia) Pty Limited
Level 1, 82 Waterloo Road
Macquarie Park, NSW 2113, Australia
Phone: [phone]
Fax: [phone]
Email: [e-mail]

EUROPE AND MIDD LE EAST

BQT Solutions (UK) Limited
Regal House, 70 London Road
Twickenham, TW1 3QS
United Kingdom
Phone: [phone]
Fax: [phone]
Email: [e-mail]

GREATER ASIA

BQT Solutions Singapore Office
Mediapolis
71 Ayer Rajah Crescent #03-03
Singapore 139951
Phone: [phone]
Fax: [phone]
Email: [e-mail]

Copyright © 2012 BQT S olutions Limi ted. BQT Solutio ns and the BQ T solutions l ogo are register ed trademarks of BQT Solutions (Australia) Pty Ltd.

Wiring diagram

Note:

• A shielded cable is recommended to be used. The shield is connected to controller 0V reference

• Maximum wie gand data cable length: 150 meters (500 feet)

• Buzzer and LED are activated when buzzer and LED line go below 2.5V.

• RS485 lines and Relay lines are only for optional use

• Some models have additional wires/connectors which are not specified in the diagram above. These wires are for other

requirements. DO NOT connect them unless specified from BQT Solutions or a BQT authorized distributor. Any damage
caused by incorrect connection will void the warranty

• Terminate or insulate all un-used wires

Regulatory Information

C-Tick: This device is C-Tick complied.
CE: The device has passed all relevant tests and obtained CE approval.
FCC: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1) this device

may not cause harmful interference and 2) this device must accept any interference received, including interference that
may cause undesired operation of the device.
Warning: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part
15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-Consult the dealer or an experienced radio/TV technician for help.
Any changes or modifications not expressively approved by BQT Solutions could void the user’s authority to operate this
equipment.

9

Series

INSTALLATION GUIDE

Version4.1

Installation

Remove the cover by holding the unit as shown and pulling the cover from
the top as illustrated

Note: DO NOT use a screw driver or other implement to remove cover

If necessary, drill holes in the wall for the mounting screws or mounting
box on which the reader unit will be placed. (Use the Drilling Template
provided overleaf).

1. Place the controller and power supply cable through the grommet hole.

2. Drill the holes as indicated by the arrows.

Note: Make sure that you don't drill through the cable.

Wire connection
Note:

Power to the unit is provided from the listed control unit or from a
separately UL listed 12V DC power-limited, access control power source.
DO NOT supply power during installation.

Wiring methods shall be in accordance with the Electrical wiring regulation
in your country / region.

Check your circuit diagram for the colour coding of the circuit wiring. The
reader can be damaged beyond repair if the wiring is connected incorrectly.
This will void the warranty.

1. Connect the 0V wire to the power 0V line;

Note: The 0V line of all power supplies must be connected to a common 0V reference

point.

2. Connect the Wiegand data wires;

3. Connect the Buzzer and LED wires;

4. Connect 12V DC wire;

5. Place reader on the wall (Make sure the wires are not crushed. This

will void the warranty if damage occurs)

6. Insert and hand tighten the screws;

7. Check that the reader is level before tightening the screws;

Note: Excessive tightening of screws may deform the casing, resulting in a damaged

unit. This will void the warranty.

8. Turn on the 12V DC power to power up reader.

9. Allow 5 – 10 seconds for reader to finish initialization (depends on the

application). Make sure reader is functioning correctly according to
the application specification.

External Use

• Make sure the wire bundle to the reader has an IP rating of at least IP65

Handling

• Handle the reader with care. DO NOT damage or drop unit before

installation. This will void the warranty.

• If the case is damaged, the reader may not be to the specified IP rating.

Replace the reader if the case is damaged.

Maintenance

• Once installed the reader requires no maintenance.

Troubleshooting

Problem

Troubleshoo ting steps

Power on rea der – reader does

not start up

1. Check connections

2. Check the voltage a t the reader

3. Check the current capability of the power

supply

Power on rea der – reader keeps

beeping

1. Check buzzer line

2. Check the voltage a t the reader

3. Check the current capability of the power

supply

Power on rea der – LED stays
green

1. Check LED line

Present a card to reader – a beep

is heard but reade r does not
output any data

1. Check whether the card has data encoded

2. Check the wiegand connection to controlle r

3. Check the voltage level on wiegand data lines

Present a card to reader – no

response from reader

1. Try a known working card

2. Check if the reader requires to be configured

with a confi guration car d

If the proble m still pers ists, please contact your distributor for technical support.

Warranty

Unless specified otherwise, the Company warrants to the Customer that’
BQT Solutions Branded Products’ (excluding third party products and
software) are covered by a return to base warranty on defects in materials
and workmanship affecting normal use for a period of the Warranty offered
under the Standard Terms and Conditions of Sale from BQT invoice date
(‘Standard Warranty’)

This standard warranty does not cover damage, fault, failure or malfunction
due to external causes including; accident, misuse, problems with electrical
power, servicing not authorised by the Company, usage and/or storage
and/or installation not in accordance with Product instructions, failure to
perform required preventative maintenance, normal wear and tear, act of
God, fire, flood, war, any violent or similar occurrence; any attempt by any
person other than Company personnel or any person authorised by the
Company to repair or support the Products and problems caused by use of
parts and components not supplied by the Company. The standard warranty
does not cover any items that are in one or more of the following categories:
software; external devices; accessories or parts added to the product after
the product has been shipped from BQT Solutions.

During the warranty, period beginning on the invoice date, the Company will
repair or replace faulty products (at its absolute discretion) returned to its’
factory. The Customer must prepay shipping and transportation costs and
insure the shipment or accept the risk of loss or damage during such
transportation.

The Customer shall be solely responsible for determining suitability for use
and the Company will, in no event, be liable in this respect. This standard
warranty is given in place of all warranties, conditions, terms, undertakings
and obligations implied by statute, common law, trade usage, and course of
dealing or otherwise including warranties or conditions of merchantability,
fitness for purpose, satisfactory quality and / or compliance with description,
all of which are hereby excluded to the fullest extent permitted by law.