Page 1
1 x
2 x
6 x
2 x
2 x
Cross Head Screwdriver
Drill
Level
3mm
Drill Bit
5mm
Drill Bit
1
3
6
5
7
Panels Hardware
ASSEMBLY GUIDE
Minimum Tools required
Hammer
12 x Standard
B
4
WALL
Cabinets
1 x RH Side
1 x LH Side
1 x Top
1 x Base
1 x Back
2 x Shelves for Standard 3 x for Tall
1 x Rail
1 x Centre Muntin
1
2
3
4
5
6
2
6
AA
P
BB
BC
800 -1000mm
Standard and Tall
6
7
18 x Tall
B
H
50 mm
8
8
4 x
K
25mm
Before you Start …
WARNING: Installation should be performed by a competent person only. This product could
be dangerous if incorrectly installed. All assembly fittings except legs and shelf pegs have
been pre-inserted. If any are missing or there is a problem with the panels, please call the
Manufacturers’ Helpline on 01769 575500, and their team will get things sorted.
Video assembly guides can be viewed at www.mycabin etguide.co.uk
Cleaning – Use mild soap and water only. Do not use abrasive cleaners.
Please use scissors to open the
bag of fittings and then empty
the contents into a bowl, so
that they do not get lost!
Hinges Supplied Separately
14 x Standard
2 x
D
F
22 x Tall
F
20mm
Page 2
Fit panels & to panel , tightening metal cams as you go.
Slide panel into position.
354 1
1
3
4
5
2
3
4
5
7
17
A (mm) B (mm)
800mm Wall 60 100
1000mm Wall 60 150
5
7
1
2
4
A
B
60mm
B
A
60mm
1
2
3
Fully insert the shelf pegs , at required position, (the back of the plastic collar must
finish flush with the face of the side panel). Rest the shelf on the pegs, and line up with
the plastic inserts. Now tap down firmly to secure.
NOTE: To remove the shelf, gently tap up and take out, push shelf peg in turn anticlockwise
with a screwdriver and pull out.
B
B
Shelf Fitting
4
8
1
4
3
5
2
7
Fit panel to panel . Then, fit panel to
panels , , and .
Fit panel to panels & using
4 x screws.
Tighten metal cams.
8
3
4
H
Now secure the
base panel to
the back rail ,
using 2 x
screws .
4
7
H
H
H
It is recommended, when hanging this unit,
that additional fixings (not supplied)
are used at the bottom of the unit.
Using an appropriate drill bit,
four holes should be drilled
through panels and ,
in the suggested positions
indicated (refer to table below),
in order to achieve this.
5 7
CSS1110 01/12
Page 3
Drill a 5mm hole through both side panels. Join together using joining bolts .
Stage 1:
Hold Wall plate between hands and snap at centre to produce one left hand and one right hand wall plate
Stage 2:
Position and secure wall plates to the wall with
suitable fixings.
WARNING: This unit could be dangerous if fitted
incorrectly to wall. (Fixings are not supplied with the
pack, as they vary according to the type of walls you
have. If you are unsure, ask an expert).
AA
Stage 3:
Position the wall hanging brackets into the large
holes at the top of the LH and RH end panels ( & ),
as shown, and ensure they are fully inserted.
P
1
Stage 5:
To adjust the height of the Wall Hanging Brackets .
P
Stage 6:
Turn screwdriver clockwise
to pull cabinet towards wall.
AA
1 2
LH
Side
Panel
RH
Side
Panel
Snap here
Bottom Flap
Down
P P
2
Stage 7:
When correctly positioned, push in cover caps
BB
Stage 4:
Pull the bottom flap down to lock the hanging brackets.
Finally, they must be secured into place at the bottom,
using 1 x to each bracket, as shown.
Note: This screw
must be fitted
TOP OF WALL CABINET
43mm
Approx 20mm
For secure fixing of this unit, you should now fix to the
wall through the bottom of the unit, as detailed earlier.
Turn screwdriver clockwise to reduce height
Turn screwdriver anticlockwise to increase height
Turn screwdriver anticlockwise
to release cabinet from wall
Insert the metal frame brackets, at an angle, into the holes in the
back of the frame, and then straighten them up, to grip the holes,
before fitting the frame. Carefully push the frame (with brackets)
onto the front of the cabinet, and adjust to the correct position.
Finally, secure the frame brackets to the cabinet with
screws (supplied in hinge pack).
unit
Frame Fitting
7
NOTE: Where frames are to be fitted to this unit, the frame
fixing brackets can only be used for fitting to panels & .
Where the frame is to be fitted to panel , the countersunk
holes on the inside face of panel will need to be carefully
drilled through, with a 5mm drill bit. Then, both frames will
need to be secured to panel , using 4 x .
1
K
C
Snap here
Fitting to wall
5
2
2
1
1
Joining of Cabinets
D
6
C
frame
Supplied in Hinge Packs For Inset Doors and Frames only
2
8
8
8
AA
1
2
P
BC
BC
Page 4
Lay on
Fit each soft closer next
to centre muntin on the
top or bottom panel.
CSS1110 01/12
Fit each Door Stop ‘A’ to the
back of the Frame joined to
the top panel with 2 x screws
supplied
Fit to holes drilled in bottom panel, so that closers are
either side of centre muntin.
Handles Position as required.
NOTE: care should be taken when drilling for the handle so as not to drill in to the shelf.
Soft Closer (This section details all options available.)
Insert Door Hinge into
rear recess in door
Affix Hinge Plate
on cabinet
Now, Clip Hinge onto Hinge Plate
Turn screws as shown to adjust door position
Door Hinges
mounting plate for
Inset Doors Only
You should follow the details that refer to the system you have purchased.
8
9
10
Frame
Firstly, when fitting soft closers to framed doors only,
locate the 4 pre-marked holes in the bottom panel, and
using a 5mm drill bit, carefully drill these to a depth of
12mm.
Fixing of Magnetic Catch
First, carefully push the magnetic
catch , into the holder ,
as shown, until it clips onto the
adjustment screw at the end.
BASE PANEL
8mm
15mm
screw
fixing
adjustment
screw
Fixing of Strike Plate
Using a 3mm drill bit, carefully drill a 3mm hole in the
door, as shown.
Now tap the strike plate into this hole, and close
the door.
LH hung wall door shown
3mm hole drilled
for metal striking
plate
20mm
43mm
The door should be
pushed onto the
magnetic catch,
to close it. Then,
to open the door,
simply push the
door again, and
release, and the
door should open.
If the door does
not open smoothly,
then it may require
further adjustment
of the hinges.
Push-to-open only:
ARAS
AT
AS
AR
AT
43mm
11mm
This is now ready to be fitted to the unit.
Carefully mark holes for fixing the holder, in the
positions shown, and using a 3mm drill bit, drill
approximately 5mm
deep.
Then fix the
complete magnetic
holder to the side
panel, as shown.
Once fitted, use the
adjustment screw
to fix the catch
in the optimum
position.
AS
Loading...