SHOWER SYSTEM FAUCET
In sta ll a tio n ins tru c tio n
A3801
CH /BN/ MB/B G/OR B
Website:www.boyellivng.com
Customer Service：: 323-982-8955
Email: service@boyelliving.com
1、IN S TALLATI ON PRECAUTI ONS
3 CONCEALED FAUCET ACCESSORIES LIST、
D
C
B
B1
A1
A
B2
B3
A4
A3
A2
A5
A3
No.
A
A-1
A-2
A-3
A-4
A-5
B
B-1
B-2
B-3
C
D
E
Description
Pressu re bala nced di verte r va lve
Valve
Face pla te with s ealjo in t
Dive rter kn ob kit
Trim cap
Alle n screw
Hand held Sh ower Ki t with Fl ex ibl e Ho se
Flex ible ho se
Hand s hower h older
Hand s hower
Show er head
Show er arm an d flang e kit
Bath tub spo ut
1. When you open the product packaging, please check the product and accessories at first.
If there are any discrepancies, please contact us promptly. We will provide you with a
satisfactory solution.
2. The hot and cold water supply pipe of the valve must be properly connected. When facing the
front of the valve, the hot water supply is on the left and cold water supply is on the right.
Incorrect connection will cause permanent damage to the cartridge.
3. If the accessories to be changed without affecting the use, we will not make a prior notice.
4. The impurities in the water supply pipe must be cleared before installation to avoid blockage.
5. The water pressure of the faucet is 0.05MPa-1.0MPa(including cold water and hot water
Pressure). Applicable water temperature range:39°F-194°F.
2、PREPARATION BEFORE INSTALLATION
CONNECTION ADVICE
Fir mly han d tighte n the hos e
to the v alve and a dd a quar ter
tur n using t he prope r wrench
Tig hten more i f neede d
* App ly plum ber's
put ty unde r the pla stic
cov er deck p lcta to s eal
you r insta llati on.
*Th e model s hown in
the i nstal latio n steps
may d iffer f rom the o ne
in bo x howev er
con necti on type a nd
ins talla tion st eps are
the s ame.
Plum be r' s
putt y
Includ ed
Threa d se al
tap e
A5
A4
E
CARE INSTRUCTIONS
DO NOT:
4、TECHNICAL DRAWING OF DRILING SIZE
1. The size of the valve that needs to be drilled is 5.3" x 6.7".
2. The depth of the valve is 1.8"-2.2". It's better to drill the depth of 1.8" for blank wall.
2.2"
1.8-2"
Wall
5.3"
2.68"2.8"
6.7"
HEAD SHOWER
HAND SHOWER
COLD WATERHOT WATER
BATHTUB SPOUT
5、PIPE CONNECTION
1. Pleas e drill the hol es on the wall fo r the main body p art, hot an d co ld water in le t pipes as
well as sh ower arm conn ection pipe s according t o the basic p ro duct dime ns ion drawi ng a s
Below.
2. Pleas e make hot and co ld water inle t pipe, the mix ed water ou tl et pipe con ne ct with con tr ol
valve, a nd tighten wi th the wrench .
6、WATER TESTING AND SEALING TESTING
1. After t he pipe conne ction is comp leted, open t he protec ti ve panel an d co ver, and th en o pen
the cart ridge, flus h the pipelin e;then clos e the cartr id ge to check t he p ressure r es istance
and seal ing perform ance of the pip eline, make s ure there a re n o leakage .
2. Block e ach outlet pi pe with a stopp er then open th e cartrid ge t o check if th e pi pe joint is
well-s ealed and the p ipe conditi on under pres sure to ens ur e no leakag e.
Testing Pu rpose: Flush th e im purities and sl udge in the pipel in e to avoid cloggi ng and affect
the efflue nt functions.
Head Shower
9、SHOWER SETS INSTALLATION / HANDLE SHOWER INSTALLATION
①
③
②
④
Hot
Hand shower
Cold
7、THE PROCEDURE OF SEALING THE WALL
Use a para llel ruler to m easure the fl atness of the v alve and th e ve rtical wa ll s urface. I f th e
wall sur face is not fla t, it should be p atched to ens ure the val ve a nd vertic al w all angle m ee ts
at nearl y ideal angle o f 90, then lay th e tile decora tion.
8、INSTALLATION OF CONTROL VALVE
1. Take of f the protect ive panel and c over.
2. The dec orative pan el and the hand le are connec ted to the co nt rol valve a s sh own below
sequen ce.
3. Accor ding to the fig ure below, pl ease correc tly adjus t th e directi on o f water sep ar ator
Handle .
Tie surface
wall
Protective
cover is roughly
even with tile
10、PRODUCT REPARATION
If the car tridge is wor n out which cau se leakage, p lease tur n of f the water s ou rce. Remo ve t he
handle , panel, and de corative co ver in sequen ce, remov e th e gland wit h a wr ench, the n ta ke
out the ca rtridge and c opper sleev e. Repair or re place the n ew c artridg e, t hen insta ll i t again in
sequen ce.
11. CLEARANCE AND MAINTENANCE
In order t o keep the fauc et appearan ce smooth and g ood perfo rm ance, ple as e follow th e be low
steps to c lean and main tain the fauc et.
1. Clean with water and dry with a soft cotton cloth.
2. Use a mild liquid and a colorless glass cleaner to remove su rface dirt a nd scale,
also you can use the cleaner without grinding function.
3. Do not use detergents, polishing tools, abrasive clo th, paper to wels or scra pers to
clean the faucet.
4. Do not use acid cleaners, insoluble granular deterge nts, soaps e tc to clean th e
Faucet.
Loading...