SHOWER SYSTEM FAUCET
In stall at ion i nst ruc ti o n
H1106
CH /BN /MB /BG/ ORB
Website:www.boyellivng.com
Customer Service：: 323-982-8955
Email: service@boyelliving.com
C
B
3 CONCEALED FAUCET ACCESSORIES LIST、
A
D
No. Descrip tion
Sh ower Head
A
1/ 2"x2" NPT Nipple
B
Top E sc ut ch eo n
C
Sh ower Arm
D
Hand Shower
E
Di verter Body & Shower Pi pe
F
Low er M ou nt
G
Soap di sh
H
St ainless Steel Hose
I
J
Low er M ou nt s cr ew
P
Wal l An ch or
1、IN STALL ATION P RECAUTI ONS
1. When you open the product packaging, please check the product and accessories at first.
If there are any discrepancies, please contact us promptly. We will provide you with a
satisfactory solution.
2. The hot and cold water supply pipe of the valve must be properly connected. When facing the
front of the valve, the hot water supply is on the left and cold water supply is on the right.
Incorrect connection will cause permanent damage to the cartridge.
3. If the accessories to be changed without affecting the use, we will not make a prior notice.
4. The impurities in the water supply pipe must be cleared before installation to avoid blockage.
5. The water pressure of the faucet is 0.05MPa-1.0MPa(including cold water and hot water
Pressure). Applicable water temperature range:39°F-194°F.
2、PREPARATION BEFORE INSTALLATION
CONNECTION ADVICE
Fir mly han d tighte n the hos e
to the v alve and a dd a quar ter
tur n using t he prope r wrench
Tig hten more i f neede d
* App ly plum ber's
put ty unde r the pla stic
cov er deck p lcta to s eal
you r insta llati on.
*Th e model s hown in
the i nstal latio n steps
may d iffer f rom the o ne
in bo x howev er
con necti on type a nd
ins talla tion st eps are
the s ame.
Plumber's
putty
Included
Threa d se al
tap e
G
P
C
J
Ri ns e th e p rodu ct w it h c lea r wa te r. Dry th e
E
Use a brasi ve clea nsers , cloth s, or pap er towe ls. Use
F
any c leani ng agen ts cont ainin g acid, p olish , wax,
alc ohol am monia , bleac h, solv ent or an y other
CARE INSTRUCTIONS
pr od uct wit h a s of t cl ot h.
DO NOT:
cor rosiv e or hars h chemi nalc cl eanse rs.
H
I
Turn o n
Hot
Cold
HEAD SHOWER
HAND SHOWER
Off
*N ot i nclud e val ve *
4、Installation Instructions
1. Determine length of bras s NP T ni pp le n ee de d:
a. Place mark on existing sho we r ar m at w al l su rf ace.Unscrew shower arm from elbow in
wal1.
b. Measure distance from ma rk o n sh ow er a rm t o en d of shower arm threads. Add " to this
measurement, and then rou nd t o ne ar es t/ ".
Example 1: If measurement = 1h ", a dd l" = iA ", r ounded = 2" NPT nipple-this is the length
needed.
Example 2: If measurement = 1 %" , ad d/ " =2 /" , ro un ded = 2" NPT nipple-this is the length
needed.
2. Apply generous amount of P TF E Th re ad S ea la nt Tape to both ends of nipple.
3. Hand tighten inlet fitti ng o nt o ni pp le , t he n nipple to fitting in wall. Use adjustable
wrench on inlet fitting to ti gh te nb ot hc on ne ctions simultaneously untilboth are sec ur e wi th
no leaks.
4. Slide hand shower holder o ff s ho we r pi pe .
5. Slide soap dish onto showe r pi pe t o de si re d po si tionand secure with set screw . For model
1077 slide soap dish retain er o nt o sh ow er pi pe . Slide plasticsoapdish onto shower pipe an d
push soap dish down until flu sh w it h re ta in er .
CA UT IO N-DO NO T OV ER TI GH TE N
6. Reinstall hand shower ha ng er .
7. Secure swivel joint onto b ot to m of d iv er te r body. Swivel
joint should move freely si de t o si de .
CA UT IO N—DO NO T OV ER TI GH TE N
8. Insert shower pipe into to p te e . Se cu re w it h se t screw .
9. Slide top escutcheon ove r to p te e. H IN T— L ub ricate escutcheon o-ring; a small amount of
soapy water will do the trick .
10 . Slide bottom escutc he on o ve r di ve rt er body.HINT— Lubricate escutcheon o-ring ; a sm al l
amount of soapy water will do t he t ri ck .
11 . Loosen set screw on div er te r an d sl id e lo wer mount into diverter body.
12 . Push top tee over inlet f it ti ng u nt il f lu sh against fitting. Position diverter body so
shower pipe is plumb (verti ca l) .
13 . Mark location of lowe r mo un t wi th p en ci l.
14 . Wall surface must be cl ea n of a ny r es id ue a nd completely dry. OPTION 1: 3M Tape
Remove covering of 3M Tape an d po si ti on m ou nt o n ma rked locations.
15 . Apply pressure to mou nt f or 3 0 se co nd s by p ushing firmlyagainst the wall. To ensure
proper adhesion, allow on e ho ur b ef or e us in g your ShowerSpa and keep area around the
mount as dry as possible for th e fi rs t 24 h ou rs . Ta pe andglue wi11 be fully cured after 24
hours.
16 . Position shower pip e pa ra ll el t o wa ll b y sliding diverter body on lower mount . Secure
diverter to lower mount wit h se t sc re w.
17 . Insert rubber washe r in to b ot h en ds o f ho se. Connect hex head end to swivel joint and
tapered end to hand shower . Pl ac e ha nd s ho we r in to adjustable hanger.
18 . Tighten shower head s ec ur el y to s ho we r arm .
5、SHOWER SYSTEM INSTALLATION INSTRUCTION
1
2
3
4 5
6、PRODUCT REPARATION
If the cartridge is worn out which c au se l ea ka ge , pl ea se t urn off the water source. Remove the
handle, panel, and decorative co ve r in s eq ue nc e, r em ov e the gland with a wrench, then take
out the cartridge and copper sle ev e. R ep ai r or r ep la ce t he new cartridge, then install it again in
sequence.
7. CLEARANCE AND MAINTENANCE
In order to keep the faucet appear an ce s mo ot h an d go od p er formance, please follow the below
steps to clean and maintain the fa uc et .
1. Clean with water and dry with a soft cotton cloth.
2. Use a mild liquid and a colorless glass cleaner to remove surface dirt and scale,
also you can use the cleaner without grinding function.
3. Do not use detergents, polishing tools, abrasive cloth, paper towels or scrapers to
clean the faucet.
4. Do not use acid cleaners, insoluble granular detergents, soaps etc to clean the
Faucet.
Loading...