Boxlight CD715x User Manual

19462 Powder Hill Place Poulsbo, WA 98370

800.762.5757

360.779.7901 www.boxlight.com

CD715x

USER MANUAL

Copyright

This publication, including all photographs, illustrations and software, is protected under international copyright laws, with all rights reserved. Neither this manual, nor any of the material contained herein, may be reproduced without written consent of the author.

Disclaimer

The information in this document is subject to change without notice. The manufacturer makes no representations or warranties with respect to the contents hereof and specifically disclaims any implied warranties of merchantability or fitness for any particular purpose. The manufacturer reserves the right to revise this publication and to make changes from time to time in the content hereof without obligation of the manufacturer to notify any person of such revision or changes.

Trademark Recognition

All product names used in this manual are the properties of their respective owners and are acknowledged.

D

L

P

r

o

j

e

c

t

o

r

—

U

s

e

r

M

a

n

u

a

l

D

L

P

r

o

j

e

c

t

o

r

—

U

s

e

r

L

P

r

o

j

e

c

t

o

r

—

U

M

s

e

r

M

a

n

u

a

l

a

n

u

a

l

Important Safety Information

Congratulations on purchasing the DLP projector!

Important:

It is strongly recommended that you read this section carefully before using the projector. These safety and usage instructions will ensure that you enjoy many years safe use of the projector. Keep this manual for future reference.

Symbols Used

Warning symbols are used on the unit and in this manual to alert you of hazardous situations. The following boxes are used in this manual to alert you to important information.

Note:

Provides additional information on the topic at hand.

Important:

Provides additional information that should not be overlooked.

Caution:

Alerts you to situations that may damage the unit.

Warning:

Alerts you to situations that may damage the unit, create a hazardous environment, or cause personal injury.

Throughout this manual, component parts and items in the OSD menus are denoted in bold font as in this example: “Push the Menu button on the remote control to open the Main menu.”

Main Features

• Lightweight unit, easy to pack away and transport

• Compatible with all major video standards including NTSC, PAL, and SECAM

• A high brightness rating allows for presentations in daylight or in lit rooms

• Supports resolutions up to XGA at 16.7 million colors to deliver crisp, clear images

• Flexible setup allows for front rear and ceiling projection

• Line-of-vision projections remain square, with advanced keystone correction for angled

projections

• Input source automatically detected

— ii —

Remote Control

The remote control has a laser for pointing out items on a screen.

DANGER: Do not point the laser in the eyes. Doing so can damage the eyes permanently.

General Safety Information

 Do not open the unit case. Aside from the projection lamp, there are no user-serviceable parts in

the unit. For servicing, contact qualified service personnel.

 Follow all warnings and cautions in this manual and on the unit case.  The projection lamp is extremely bright by design. To avoid damage to eyes, do not look into the

lens when the lamp is on.

 Do not place the unit on an unstable surface, cart, or stand.  Avoid using the system near water, in direct sunlight, or near a heating device.  Do not place heavy objects such as books or bags on the unit.

Power Safety

 Only use the supplied power cord.  Do not place anything on the power cord. Place the power cord where it will not be in the way of

foot traffic.

P

r

e

f

a

c

e

P

r

P

r

e

f

a

c

e

f

a

c

e

 Remove the batteries from the remote control when storing or not in use for a prolonged period.

Replacing the Lamp

 Replacing the lamp can be hazardous if done incorrectly. Refer to “Replacing the Projection Lamp”

on page 26 for clear and safe instructions for this procedure.

 Unplug the power cord.  Allow the lamp sufficient time to cool.

Cleaning the Projector

 Unplug the power cord before cleaning. Refer to “Cleaning the Projector” on page 28.  Allow the lamp sufficient time to cool.

Regulatory Warnings

 Before installing and using the projector, read the regulatory notices in the “Regulatory Compli-

ance” section on page 39.

About this manual

This manual is intended for end users and describes how to install and operate the DLP projector. Wherever possible, relevant information—such as an illustration and its description—has been kept on one page. This printer-friendly format is both for your convenience and to help save paper and thereby protect the environment. It is suggested that you only print sections that are relevant to your needs.

– iii –

D

L

P

r

o

j

e

c

t

o

r

—

U

s

e

r

M

a

n

u

a

l

D

L

P

r

o

j

e

c

t

o

r

—

U

s

e

r

L

P

r

o

j

e

c

t

o

r

—

U

M

s

e

r

M

a

n

u

a

l

a

n

u

a

l

Table of contents

GETTING STARTED.......................................................................................................................................................... 1

PACKING CHECKLIST........................................................................................................................................................... 1

VIEWS OF PROJECTOR PARTS............................................................................................................................................... 2

Front-left view................................................................................................................................................................. 2

Top view—OSD buttons and LEDs................................................................................................................................. 3

Rear view—connectors ................................................................................................................................................... 5

Bottom view..................................................................................................................................................................... 7

REMOTE CONTROL PARTS ................................................................................................................................................... 8

REMOTE CONTROL OPERATING RANGE............................................................................................................................... 9

PROJECTOR AND REMOTE CONTROL BUTTONS.................................................................................................................. 10

SETUP AND OPERATION...............................................................................................................................................11

INSERTING THE REMOTE CONTROL BATTERIES ................................................................................................................. 11

CONNECTING INPUT DEVICES ............................................................................................................................................ 12

STARTING AND SHUTTING DOWN THE PROJECTOR............................................................................................................. 13

ADJUSTING THE PROJECTOR LEVEL................................................................................................................................... 14

ADJUST THE ZOOM, FOCUS AND KEYSTONE...................................................................................................................... 15

ADJUSTING THE VOLUME .................................................................................................................................................. 16

ON-SCREEN DISPLAY MENU SETTINGS................................................................................................................... 17

ON-SCREEN DISPLAY MENU CONTROLS ........................................................................................................................... 17

Navigating the OSD ...................................................................................................................................................... 17

Setting the OSD Language............................................................................................................................................ 18

Main Menu.................................................................................................................................................................... 19

Setup Menu ................................................................................................................................................................... 21

Config Menu ................................................................................................................................................................. 22

Utility Menu.................................................................................................................................................................. 23

Language Menu ............................................................................................................................................................ 24

Status Menu................................................................................................................................................................... 25

MAINTENANCE AND SECURITY................................................................................................................................. 26

REPLACING THE PROJECTION LAMP................................................................................................................................... 26

Resetting the Lamp........................................................................................................................................................27

CLEANING THE PROJECTOR................................................................................................................................................28

Cleaning the Lens ......................................................................................................................................................... 28

Cleaning the Case......................................................................................................................................................... 29

USING THE KENSINGTON LOCK .........................................................................................................................................29

TROUBLESHOOTING..................................................................................................................................................... 30

COMMON PROBLEMS AND SOLUTIONS ............................................................................................................................... 30

TIPS FOR TROUBLESHOOTING............................................................................................................................................ 30

LED ERROR MESSAGES .................................................................................................................................................... 31

IMAGE PROBLEMS.............................................................................................................................................................. 31

LAMP PROBLEMS............................................................................................................................................................... 32

REMOTE CONTROL PROBLEMS .......................................................................................................................................... 32

AUDIO PROBLEMS ............................................................................................................................................................. 32

HAVING THE PROJECTOR SERVICED .................................................................................................................................. 33

SPECIFICATIONS.............................................................................................................................................................34

SPECIFICATIONS................................................................................................................................................................. 34

Input/output connectors................................................................................................................................................ 35

PROJECTION DISTANCE VERSUS PROJECTION SIZE............................................................................................................. 36

TIMING MODE TABLE........................................................................................................................................................ 37

DIMENSIONS ...................................................................................................................................................................... 38

REGULATORY COMPLIANCE..................................................................................................................................... 39

FCC WARNING.................................................................................................................................................................. 39

CANADA ............................................................................................................................................................................ 39

SAFETY CERTIFICATIONS................................................................................................................................................... 39

EN 55022 WARNING ......................................................................................................................................................... 39

— iv —

GETTING STARTED

Packing Checklist

Carefully unpack the projector and check that the following items are included:

250V P

CD-ROM (

OWER

T

HIS

C

ABLE

U

SE

DLP P

R

’

S

ROJECTOR WITH LENS CAP REMOTE CONTROL

WITH TWO AAA BATTERIES)

(

M

ANUAL

)

USB C

M

ABLE

ULTI

-

LANGUAGE

S-V

IDEO

Q

UICK

S

TART

G

UIDE

C

ABLE

C

OMPUTER

C

ARRY

ING

C

ABLE

DB15)

C

ASE

(DVI-

Contact your dealer immediately if

Caution:

1. Avoid using the projecto

2.

r in dusty environments.

Leave the pow placing the projector inside the soft case. Placing the proj could cause the projector to break dow case w

i

er cable plugged in (for

th the lens facing upw

any items are missing, appear damaged,

5-10 minutes) until the projector re

n. Be sure to a

ard.

or if the unit does not work.

turns to room temperature before

ector into the case soon after sw

ttach the lens cap and place the projector into the soft

itching off the pow

er

D

L

P

r

o

j

e

c

t

o

r

—

U

s

e

r

M

a

n

u

D

L

P

r

o

j

e

c

t

o

r

—

U

s

e

r

L

P

r

o

j

e

c

t

o

r

—

U

M

s

e

r

M

a

n

u

a

n

u

Views of Projector Parts

Front-left view

l

a

l

1

8

ITEM LABEL DESCRIPTION SEE PAGE:

7

6

5

2

4

3

1.

2.

3.

4.

5.

6.

7.

8.

Important:

Grill openings on the projector allow for good air circulation, which keeps the projector lamp cool. Do not obstruct any of the grill openings.

Zoom Enlarges the projected image

See OSD buttons and LEDs below

Projection lamp cover Remove when changing lamp

IR receiver Receiver for IR signal from remote control

Lens/focus Remove cover, turn the lens to focus

Height adjuster Adjusters drop down when adjuster button is

pushed

Height adjuster button Push to release height adjuster

Speaker Built-in mono speaker

15

3

26

9

15

14

– 2 –

Top view—OSD buttons and LEDs

12 3 4

KEYSTONE

VOL -

G

e

t

i

n

g

S

t

a

r

t

e

d

—

V

i

e

w

s

o

f

P

r

G

e

t

i

n

g

S

t

a

r

t

e

d

—

V

i

e

w

G

e

t

i

n

g

S

t

a

r

t

e

d

—

POWERREADY

V

s

i

e

w

s

o

f

P

r

o

f

P

r

o

P

a

r

t

s

j

e

c

t

o

r

j

e

c

t

o

j

e

c

t

o

r

P

a

r

t

s

P

a

r

t

s

5

POWER

6

SOURCE

7

VOL +

AUTO

MENU

1011

8 9

ITEM LABEL DESCRIPTION SEE PAGE:

1.

Volume/ left cursor

Decreases volume Navigates and changes settings in the OSD

16

2.

3.

Keystone/ Up cursor

Ready (LED)

Corrects image-trapezoid (narrower top) effect Navigates and changes settings in the OSD

Orange Lamp ready—you can safely turn on or off the projector

Flashing Lamp not ready—do not press the power button

4.

5.

6.

7.

Power Turns the projector on or off (main power switch must

be turned on first, see item 8 on page 5)

Power (LED)

Source Detects the input device

Volume/ right cursor

Green Unit is powered on and working correctly Off Unit is powered off

Flashing Operational error code

(refer to “LED Error Messages” on page 31)

Increases volume Navigates and changes settings in the OSD

– 3 –

13

17

D

18

L

P

r

o

j

e

c

t

o

r

—

U

s

e

r

M

a

n

u

a

l

D

L

P

r

o

j

e

c

t

o

r

—

U

s

e

r

L

P

r

o

j

e

c

t

o

r

—

U

M

s

e

r

M

a

n

u

a

l

a

n

u

a

l

ITEM LABEL DESCRIPTION SEE PAGE:

8.

9.

10.

11.

Auto Optimizes image size, position, and resolution

Menu Opens/exits the On-Screen Display (OSD)

Enter Changes settings in the OSD

Keystone/ Down cursor

Corrects image-trapezoid (narrower bottom) effect Navigates and changes settings in the OSD

– 4 –

Rear view—connectors

G

e

t

i

n

g

S

t

a

r

t

e

d

—

V

i

e

w

s

o

f

P

r

e

t

i

n

g

S

t

a

r

t

e

d

—

V

i

e

w

e

t

i

n

g

S

t

a

r

t

e

d

—

V

s

i

e

w

s

o

f

P

r

o

f

P

r

o

P

a

r

t

s

j

e

c

t

o

r

j

e

c

t

o

j

e

c

t

o

r

P

a

r

t

s

P

a

r

t

s

12

18

17

16

15

14

3456

10111213

9

7

8

ITEM LABEL DESCRIPTION SEE PAGE:

1.

2.

3.

DVI-I Connect the DVI cable (supplied) from a computer

RGB IN Connect a VGA cable (not supplied) from a computer

RGB OUT Connect to a monitor

4.

5.

6.

7.

8.

9.

10.

11.

12.

13.

RS-232 Installation control and firmware upgrades

USB Connect the USB cable (supplied) from a computer

Audio-in Connect the audio cable (supplied) from the input device

Power connector Connect the supplied power cord

Main power Turns the main power on or off

IR receiver Receiver for IR signal from remote control

Audio-out Audio loop-thru

Audio-in-R Connect an RCA audio cable (not supplied) from the input

device right channel

Audio-in-L Connect an RCA audio cable (not supplied) from the input

device left channel

Video Connect a composite video cable (not supplied)from a

video device

13

9

13

14.

15.

S-video Connect the supplied S-video cable from a video device

Kensington Lock Secure to permanent object with a Kensington Lock system

– 5 –

29

D

L

P

r

o

j

e

c

t

o

r

—

U

s

e

r

M

a

n

u

a

l

D

L

P

r

o

j

e

c

t

o

r

—

U

s

e

r

L

P

r

o

j

e

c

t

o

r

—

U

M

s

e

r

M

a

n

u

a

l

a

n

u

a

l

ITEM LABEL DESCRIPTION SEE PAGE:

16.

17.

18.

Note:

If your video equipment has both S-video and RCA jacks (composite video) connect to the S-video connector. S-video provides a better quality signal.

Pr/Cr

Pb/Cb

Y

Component video in

Connect a component video enabled device

13

– 6 –

Bottom view

2 3 3 3112

G

e

t

i

n

g

S

t

a

r

t

e

d

—

V

i

e

w

s

o

f

P

r

e

t

i

n

g

S

t

a

r

t

e

d

—

V

i

e

w

e

t

i

n

g

S

t

a

r

t

e

d

—

V

s

i

e

w

s

o

f

P

r

o

f

P

r

o

P

a

r

t

s

j

e

c

t

o

r

j

e

c

t

o

j

e

c

t

o

r

P

a

r

t

s

P

a

r

t

s

ITEM LABEL DESCRIPTION SEE PAGE:

1.

2.

3.

Height adjuster buttons Push to release height adjusters

Height adjusters Adjusters drop down when adjuster buttons

are pushed

Ceiling support holes Contact your dealer for information on mounting the projector on a

ceiling.

14

– 7 –

D

Blank

L

P

r

o

j

e

c

t

o

r

—

U

s

e

r

M

D

L

P

r

o

j

e

c

t

o

r

—

D

L

P

r

o

j

e

c

Remote Control Parts

U

t

o

r

—

U

a

s

e

r

M

a

s

e

r

M

a

n

u

a

l

n

u

a

l

n

u

a

l

22 21

20 19

18 17

16 15

Powe r

Source

Menu

Volume

1

Freeze

Mute

2

3

Auto

4

Blank

5

Enter

6

7

8

9 10

Keystone

11

12

1

14

Important:

1. Avoid using the projector with bright fluorescent lighting turned on. Certain high-frequency fluo-

rescent lights can disrupt remote control operation.

2. Be sure nothing obstructs the path between the remote control and the projector. If the path between remote and projector is obstructed, you can bounce the remote signal off certain reflective surfaces such as projector screens.

2

13

– 8 –

G

e

t

i

n

g

S

t

a

r

t

e

d

—

V

i

e

w

s

o

f

P

r

e

t

i

n

g

S

t

a

r

t

e

d

—

V

i

e

w

e

t

i

n

g

S

t

a

r

t

e

d

—

V

s

i

e

w

s

o

f

P

r

o

f

P

r

o

P

j

e

c

j

e

c

j

e

a

t

o

r

P

a

t

o

P

c

a

t

o

r

ITEM LABEL DESCRIPTION SEE PAGE:

r

t

s

r

t

s

r

t

s

1.

2.

3.

4.

5.

6.

7.

8.

9.

10.

11.

12.

Laser Use as on-screen pointer. DO NOT POINT IN EYES.

IR transmitter Transmits signals to projector

Status LED Lights when the remote control is used

Auto Optimizes image size, position, and resolution

Blank Makes the screen blank

Enter Changes settings in the OSD

Up cursor

Navigates and changes settings in the OSD

Right cursor

Cursor pad Moves the on-screen cursor when connected to a PC

Keystone top

Corrects image-trapezoid (narrower top/bottom) effect

Keystone bottom

Mute Mutes the built-in speaker

9

22

17

15

13.

14.

15.

16.

17.

18.

19.

20.

21.

22.

Right mouse Functions as right mouse button when connected to a PC

Left mouse Functions as left mouse button when connected to a PC

Volume down

Volume up

Down cursor

Left cursor

Menu Opens the On-Screen Display (OSD)

Freeze Freeze/unfreezes the on-screen picture

Source Detects the input device

Power Turns the projector on or off

Adjusts volume

Navigates and changes settings in the OSD

Remote Control Operating Range

The remote control uses infrared transmission to control the projector. It is not necessary to point the remote directly at the projector. Provided you are not holding the remote perpendicular to the sides or the rear of the projector, the remote functions within a radius of about (7) meters (23 feet) and 30 degrees above or below the projector level. If the projector does not respond to the remote control, move a little closer.

16

17

13

– 9 –

D

Blank

L

P

r

o

j

e

c

t

o

r

—

U

s

e

r

M

a

n

u

a

l

D

L

P

r

o

j

e

c

t

o

r

—

U

s

e

r

L

P

r

o

j

e

c

t

o

r

—

U

M

s

e

r

M

a

n

u

a

l

a

n

u

a

l

Projector and Remote Control Buttons

The projector can be operated using the remote control or the buttons on the top of the projector. All operations can be carried out with the remote control; however the buttons on the projector are limited in use. The following illustration shows the corresponding buttons on the remote control and on the projector.

13

12

11 10

7/10

Power

Auto

1

Source

Freeze

Blank

Menu

Enter

2 3 4

VOL -

9 8

Volume

Mute

Keystone

5 6

7

1

2

3/5 13

KEYSTONE

POWERREADY

POWER

12

SOURCE

4/8

VOL +

AUTO

MENU

1 11

26/9

Some buttons on the projector have two functions. For example, item 7/10 on the projector functions both as the volume down button and as the left cursor key in OSD menus.

– 10 –

Inserting the Remote Control Batteries

Remove the battery compartment cover

1.

by sliding the cover in the direction of the arrow.

Insert the supplied batteries taking note

2.

of the polarity (+/-) as shown here.

SETUP AND OPERATION

Replace the cover.

3.

Caution:

1. Only use AAA alkaline batteries.

2. Dispose of used batteries according to local ordinance regulations.

3. Remove the batteries when not using the projector for prolonged periods.

D

L

P

r

o

j

e

c

t

o

r

—

U

s

e

r

M

a

n

u

a

l

D

L

P

r

o

j

e

c

t

o

r

—

U

s

e

r

L

P

r

o

j

e

c

t

o

r

—

U

M

s

e

r

M

a

n

u

a

l

a

n

u

a

l

Connecting Input Devices

A PC or notebook computer as well as video devices can be connected to the projector at the same time. Video devices include DVD, VCD, and VHS players, as well as movie camcorders and digital still camera s. Check the user manual of the connecting device to confirm it has the appropriate output connector.

A

DVI-I IN

BS

P/C

Y

COMPONENT VIDEO IN

K

B

RGB IN

P/C

RR

S-VIDEO IN VIDEO IN L-AUDION IN -R

J

C

RGB OUT

I

H

D

RS-232C

AUDIO OUT

G

ITEM LABEL DESCRIPTION

A

B

C

DVI-I Connect the supplied DVI cable from a computer.

RGB in Connect a VGA cable (not supplied) from a computer.

RGB out Connect a VGA cable (not supplied) to a monitor.

E F

AUDIO-IN

USB

D

E

F

G

RS-232 Reserved for installation control and firmware upgrades.

USB Connect the supplied USB cable from a computer.

Audio-in Connect an audio cable (not supplied) from the computer’s audio-out connector.

Audio-out Audio loop-thru

H

L-Audio in-R Connect the audio cable (not supplied) from an audio input device.

I

Video Connect a composite video cable (not supplied) from a video device.

S-video Connect the supplied S-video cable from a video device.

Component video in

Warning:

As a safety precaution, disconnect all power to the projector and connecting devices before making connections.

Connect a component video cable (not supplied) from a video device.

– 12 –

Starting and Shutting down the Projector

Connect the power cord to the projec-

1.

tor. Connect the other end to a wall outlet. (A) Turn on the power switch. (B) The Power LED and Lamp-ready LED turn on.

S

e

t

u

p

a

n

d

O

p

e

r

a

t

i

o

n

S

e

t

u

p

a

n

d

O

p

e

S

e

t

u

p

a

n

r

d

O

p

e

r

a

t

i

o

n

a

t

i

o

n

Remove the lens cover.

2.

Turn on the connected devices.

3.

Ensure the Lamp-ready LED is on a

4.

steady (not flashing) orange and then press the Power button to turn on the projector.

The projector splash screen displays and connected devices are detected. If the connected device is a PC, press the appropriate Fn hot keys on the computer keyboard to switch the display output to the projector. (Check the PC user manual to determine the appropriate Fn hot keys to change display output.)

ON

OFF

If more than one input device is con-

5.

nected, press the Source button repeatedly to switch among devices.

To turn off the projector, press the

6.

Power button. The projector prepares for shutdown and a “Wait a moment please…” message appears.

When the “Power Off?/Press Power

7.

again” message appears, press the Power button. The projector turns off.

Attention : Power off the projector normally and unplug the power cord before moving the projector

– 13 –

D

L

P

r

o

j

e

c

t

o

r

—

U

s

e

r

M

a

n

u

a

l

D

L

P

r

o

j

e

c

t

o

r

—

U

s

e

r

D

L

P

r

o

j

e

c

t

o

r

—

Adjusting the Projector Level

Take note of the following when setting up the projector:

• The projector table or stand should be level and sturdy.

• Position the projector so that it is perpendicular to the screen.

• Be sure cables are not in the way or can cause the projector to be knocked over.

U

M

s

e

r

M

a

n

u

a

l

a

n

u

a

l

1.

2.

To raise the level of the projector, lift the projector [A] and press the height-adjuster buttons [B].

The height-adjusters drop down [C].

To lower the level of the projector, press the height-adjuster buttons and push down on the top of the projector.

– 14 –

Adjust the Zoom, Focus and Keystone

Use the Image-zoom con-

1.

trol (on the projector only) to resize the projected im-

age and screen size

Use the Image-focus con-

2.

trol (on the projector only) to sharpen the projected

image

Use the Keystone buttons

3.

(on the projector or the remote control) to correct image-trapezoid (wider top or bottom) effect.

B

A

.

S

e

t

u

p

a

n

d

O

p

e

r

a

t

i

o

n

S

e

t

u

p

a

n

d

O

p

e

S

e

t

u

p

a

n

r

d

O

p

e

r

a

t

i

o

n

a

t

i

o

n

The keystone control appears on the display.

– 15 –

D

L

P

r

o

j

e

c

t

o

r

—

U

s

e

r

M

D

L

P

r

o

j

e

c

t

o

r

—

L

P

r

o

j

e

c

U

t

o

r

—

U

a

s

e

r

M

a

s

e

r

M

a

Adjusting the Volume

Press the Volume +/- but-

1.

tons on the projector or the remote control. The volume control appears on the display.

Use the Volume +/- but-

2.

tons to adjust the level.

n

u

a

l

n

u

a

l

n

u

a

l

Press the Mute button (on

3.

the remote control only) to turn off the volume.

Press Volume +/- or

4.

Mute on the remote control to turn off mute.

– 16 –

BlankBlank

Power

Menu

Keystone

Auto

Enter

Source

Volume

Mute

Freeze

1 2

3

6 5 4

VOL -

KEYSTONE

MENU

POWERREADY

POWER

VOL +

25 4163

ON-SCREEN DISPLAY MENU SETTINGS

On-Screen Display Menu Controls

The projector has an On-Screen Display (OSD) that lets you make image adjustments and change various settings.

Navigating the OSD

You can use the remote control or the buttons on the top of the projector to navigate and make changes to the OSD. The following illustration shows the corresponding buttons on the remote control and on the projector.

D

L

P

r

o

j

e

c

t

o

r

—

U

s

e

r

M

a

n

u

a

l

D

L

P

r

o

j

e

c

t

o

r

—

U

s

e

r

L

P

r

o

j

e

c

t

o

r

—

U

M

s

e

r

M

a

n

u

a

l

a

n

u

a

l

Setting the OSD Language

You may want to reference the OSD on your projector while reading this section. Set the OSD language to your preference before continuing. (The default language is English.)

1. Press the Menu button. The Main menu appears.

2. Press

until Language is highlighted.

3. Press until the language you want is highlighted.

4. Press the Enter button to select the language.

5. Press the Menu button twice to close the OSD.

– 18 –

Main Menu

O

n

-

S

c

r

e

n

D

i

s

p

l

a

y

M

e

n

u

S

e

t

i

n

g

s

n

-

S

c

r

e

n

D

i

s

p

l

a

y

M

e

n

u

S

n

-

S

c

r

e

n

D

i

s

p

l

a

y

M

e

n

u

S

e

t

i

n

g

s

t

i

n

g

s

Press the Menu button to open the OSD menu. If necessary, press

Press

then press Enter to confirm the new setting.

to move up and down in the Main menu. Press

to change values for settings, and

to move to the Main menu.

ITEM DESCRIPTION DEFAULT

Brightness Press

Contrast Press

Sharpness Press

Color Temperature

Color Saturation

Color Tint

Gamma

Color Space Press

Press

(Range: Cool/Normal/Warm)

Press

(Range: Auto—RGB—YpbPr—YCbCr)

to adjust the brightness. (Range: 0—100) 50

to adjust the contrast. (Range: 0—100) 50

to adjust the display sharpness (Range: 1-5) 3

to adjust the video tint/hue.

to adjust the video saturation. (Range: 0—100)

to adjust the video tint/hue. (Range: 0—100)

to adjust the gamma correction of the display.

Input Gamma Brightness

PC 2.2 High MAC 1.8 High Video 2.4 Low Chart 2.2 Low B&W 2.4 High

to adjust the color space.

Normal

50

PC

Auto

Reset Resets all Main items settings except Color Saturation to default values -

– 19 –

D

L

P

r

o

j

e

c

t

o

r

—

U

s

e

r

M

a

n

u

a

l

D

L

P

r

o

j

e

c

t

o

r

—

U

s

e

r

D

L

P

r

o

j

e

c

t

o

r

—

Main Menu Items Supported for Each Input Source

Depending on the video source not all items in the OSD are available. Items that are available for each input source are marked with “X”. Items that are not available can not be selected in the OSD.

Function RGB DVI Component Video Composite Video S-Video

U

M

s

e

r

M

a

n

u

a

l

a

n

u

a

l

Brightness Contrast Sharpness Color Temperature Color Saturation Color Tint Gamma

X X X X X X X X X X X X X X X X X X X X X X X X X

X X X X X

X X

– 20 –

Setup Menu

O

n

-

S

c

r

e

n

D

i

s

p

l

a

y

M

e

n

u

S

e

t

i

n

g

s

n

-

S

c

r

e

n

D

i

s

p

l

a

y

M

e

n

u

S

n

-

S

c

r

e

n

D

i

s

p

l

a

y

M

e

n

u

S

e

t

i

n

g

s

t

i

n

g

s

Press the Menu button to open the OSD menu. Press

move up and down in the Setup menu. Press

ter to confirm the new setting.

to change values for settings, and then press En-

to move to the Setup menu. Press

to

ITEM DESCRIPTION DEFAULT

Horizontal Position

Vertical Position

Keystone

Aspect Ratio Press

Reset Resets Keystone and Aspect Ratio to default values

Setup Menu Items Supported for Each Input Source

Depending on the video source not all items in the OSD are available. Items that are available for each input source are marked with “X”. Items that are not available can not be selected in the OSD.

Function RGB DVI Component Video Composite Video S-Video

Horizontal Position

Press

(Range: -50—50)

TV (HDTV) format.

to move the image left or right. (Range: 0—100) 50

to move the image up or down. (Range: 0—100) 50

to correct distortion of the projected image.

to toggle between the 4:3 standard format and 16:9 High Definition

X

4:3

0

Vertical Position Keystone

X X X X X X

– 21 –

D

L

P

r

o

j

e

c

t

o

D

L

P

r

L

o

P

r

j

e

c

t

o

r

j

e

c

t

o

Config Menu

r

—

U

s

e

r

M

a

n

u

a

l

s

e

r

M

s

e

r

M

a

n

u

a

l

a

n

u

a

l

Press the Menu button to open the OSD menu. Press

move up and down in the Config menu. Press

ter to confirm the new setting.

to change values for settings, and then press En-

to move to the Config menu. Press to

ITEM DESCRIPTION DEFAULT

Blank Screen Press

(Range: Black – Red—Green—Blue—White)

Auto Source

Auto Power Off

Volume Press

Menu Position

Menu Display

Translucent Menu

Reset

Press

(Range: On—Off) Press

utes of inactivity (Range: On—Off)

Press

(Range: Left—Right—Center—Down—Up) Press

(Range: 10 - 20 sec.) Press

(Range: On—Off) Resets all Config screen items to default values

to select a background color for blank screen

to enable or disable automatic source detection

to enable or disable automatic shut-down of lamp after 10 min-

to adjust the audio volume level (Range: 0 - 10) 5

to position the OSD on screen

to determine the timeout delay of the OSD

to set menu screen translucency

Blue

On

Off

Center

15

Off

– 22 –

Utility Menu

O

n

-

S

c

r

e

n

D

i

s

p

l

a

y

M

e

n

u

S

e

t

i

n

g

s

n

-

S

c

r

e

n

D

i

s

p

l

a

y

M

e

n

u

S

n

-

S

c

r

e

n

D

i

s

p

l

a

y

M

e

n

u

S

e

t

i

n

g

s

t

i

n

g

s

Press the Menu button to open the OSD menu. Press

move up and down in the Utility menu. Press

ter to confirm the new setting.

to change values for settings, and then press En-

to move to the Utility menu. Press

to

ITEM DESCRIPTION DEFAULT

Video Type Press

(Range: Auto—NTSC—PAL—SECAM)

Video AGC Press

for the video source. (Range: On—Off)

Projection

Frequency Press

Tracking Press

Press

(Range: 0—180)

(Range: 0—100)

to select the video standard.

to enable or disable automatic gain control

to choose from four projection methods:

Desktop mount, front of screen

Desktop mount, rear of screen

Ceiling mount, front of screen

Ceiling mount, rear of screen

to adjust the A/D sampling clock.

to adjust the A/D sampling number.

Auto

On

Desktop front

Auto detected

Reset Resets Video Type, Video AGC, and Projection to default values

– 23 –

D

L

P

r

o

j

e

c

t

D

L

P

L

P

o

r

o

j

e

c

t

o

r

o

j

e

c

t

o

Language Menu

r

—

U

s

e

r

M

a

n

u

a

l

r

—

U

s

e

r

U

M

s

e

r

M

r

—

a

n

u

a

l

a

n

u

a

l

Press the Menu button to open the OSD menu. Press

to move up and down in the Language menu.

ITEM DESCRIPTION DEFAULT

to move to the Language menu. Press

English

French

German

Italian

Spanish

Swedish

Chinese Simplified

Chinese Traditional

Japanese

Korean

Press the cursor menu.

Press the Enter button to select the language.

button to move up and down in the

English

– 24 –

Status Menu

O

n

-

S

c

r

e

n

D

i

s

p

l

a

y

M

e

n

u

S

e

t

i

n

g

s

n

-

S

c

r

e

n

D

i

s

p

l

a

y

M

e

n

u

S

n

-

S

c

r

e

n

D

i

s

p

l

a

y

M

e

n

u

S

e

t

i

n

g

s

t

i

n

g

s

Press the Menu button to open the OSD menu. Press

move up and down in the Status menu. Press

ter to confirm the new setting.

to change values for settings, and then press En-

to move to the Status menu. Press

to

ITEM DESCRIPTION DEFAULT

Video Information

Active Source Displays the active source.

Software Version

Lamp Hours Number of hours lamp has been in Normal use and number of hours lamp

Lamp Mode Toggles between lamp modes. ECO mode uses less power but decreases

Lamp Hour Reset

Displays the resolution and refresh rate of the connected video device.

Information about the firmware version.

has been in Eco use.

the lamp brightness. After replacing the lamp, this item should be reset. Refer to “Replacing the

Projection Lamp” on page 26.

These

items are

display

only.

2000 lumens

—

– 25 –

MAINTENANCE AND SECURITY

Replacing the Projection Lamp

The projection lamp should be replaced when it burns out. It should only be replaced with a certified replacement part, which you can order from your local dealer.

Important:

1. The lamp contains a certain amount of mercury and should be disposed of according to local or-

dinance regulations.

2. Avoid touching the glass surface of the new lamp: Doing so may shorten its operation life.

Warning:

1. Be sure to turn off and unplug the projector at least an hour before replacing the lamp. Failure to

do so could result in a severe burn.

2. It is recommended that you do not attempt to replace the lamp while the projector is installed on a ceiling. If you do attempt this, wear protective goggles to prevent glass from a ruptured lamp getting into your eyes.

Lift the screw cover (A).

1.

Remove the screw on the lamp compartment cover (B) and then lift the lamp compartment cover (C).

Remove the two screws

2.

from the lamp module (A) and then lift the module handle up (B).

Pull up firmly to remove

3.

the lamp module.

M

a

i

n

t

e

n

a

i

n

t

e

n

a

i

n

t

e

n

Reverse Steps 1 to 4 to

4.

install the new lamp module. Note: The lamp module should be oriented as shown here when replacing.

M

Resetting the Lamp

After replacing the lamp, reset the lamp hour counter to zero. Refer to the following:

Press the Menu button to open the

1.

Main menu.

a

n

c

e

a

n

d

S

e

c

u

r

i

t

y

a

n

c

e

a

n

d

S

a

n

c

e

a

n

d

S

e

c

u

r

i

t

y

c

u

r

i

t

y

Press the cursor

2.

to the Status menu.

Press the cursor button to move

3.

to Lamp Hour Reset.

Press the Enter button.

4.

A message screen appears.

Press the cursor buttons in this order:

5.

; ; ; .

The “Lamp Hour Reset OK !!” message appears. Then the Status menu appears again showing the Lamp Hours reset to zero.

button to move

Lamp Hour Reset OK !!

– 27 –

D

L

P

r

o

j

e

c

t

o

r

—

U

s

e

r

M

a

n

u

a

l

D

L

P

r

o

j

e

c

t

o

r

—

U

s

e

r

L

P

r

o

j

e

c

t

o

r

—

U

M

s

e

r

M

a

n

u

a

l

a

n

u

a

l

Cleaning the Projector

Cleaning the projector to remove dust and grime will help ensure trouble-free operation.

Warning:

1. Be sure to turn off and unplug the projector at least an hour before cleaning. Failure to do so

could result in a severe burn.

2. Use only a dampened cloth when cleaning. Do not allow water to enter the ventilation openings on the projector.

3. If a little water gets into the projector interior while cleaning, leave unplugged in a well-ventilated room for several hours before using.

4. If a lot of water gets into the projector interior when cleaning, have the projector serviced.

Cleaning the Lens

You can purchase optic lens cleaner from most camera stores. Refer to the following to clean the projector lens.

1. Apply a little optic lens cleaner to a clean soft cloth. (Do not apply the cleaner directly to the lens.)

2. Lightly wipe the lens in a circular motion.

Caution:

1. Do not use abrasive cleaners or solvents.

2. To prevent discoloration or fading, avoid getting cleaner on the projector case.

– 28 –

M

a

i

n

t

e

n

a

n

c

e

M

a

i

n

t

e

n

a

i

n

t

e

n

a

n

c

e

a

n

c

e

a

Cleaning the Case

Refer to the following to clean the projector case.

1. Wipe off dust with a clean dampened cloth.

2. Moisten the cloth with warm water and mild detergent (such as used to wash dishes), and wipe the case.

3. Rinse all detergent from the cloth and wipe the projector again.

Caution:

To prevent discoloration or fading of the case, do not use abrasive alcohol-based cleaners.

Using the Kensington Lock

If you are concerned about security, attach the projector to a permanent object with the Kensington slot and a security cable.

n

d

S

e

c

u

r

i

t

y

n

d

S

e

n

d

S

e

c

u

r

i

t

y

c

u

r

i

t

y

Note:

Contact your vendor for details on purchasing a suitable Kensington security cable.

– 29 –

TROUBLESHOOTING

Common problems and solutions

These guidelines provide tips to deal with problems you may encounter while using the projector. If the problem remains unsolved, contact your dealer for assistance.

Often after time spent troubleshooting, the problem is traced to something as simple as a loose connection. Check the following before proceeding to the problem-specific solutions.

• Use some other electrical device to confirm that the electrical outlet is working.

• Ensure the projector is turned on.

• Ensure all connections are securely attached.

• Ensure the attached device is turned on.

• Ensure a connected PC is not in suspend mode.

• Ensure a connected notebook computer is configured for an external display. (This is usu-

ally done by pressing an Fn-key combination on the notebook.)

Tips for Troubleshooting

In each problem-specific section, try the steps in the order suggested. This may help you to solve the problem more quickly.

Try to pin point the problem and thus avoid replacing non-defective parts. For example, if you replace batteries and the problem remains, put the original batteries back and go to the next step.

Keep a record of the steps you take when troubleshooting: The information may be useful when calling for technical support or for passing on to service personnel.

LED Error Messages

STATUS/

NUMBER OF

LED

FLASHES

T

r

T

r

T

r

DESCRIPTION REMEDY

o

u

b

l

e

s

h

o

t

i

n

g

o

u

b

l

e

s

h

o

u

o

b

l

e

s

h

o

t

i

n

g

o

t

i

n

g

Power

Ready

Flashing Lamp not ready Do not press the power button.

3 System overheated Allow the projector to cool down.

4 System interface error Contact your dealer for assistance.

5 Lamp error Replace the lamp module. 6 Fan error Refer to Ready LED status in this

table to determine which fan.

7 Lamp cover open Close the lamp cover.

8 DLP driver error

Contact your dealer for assistance.

9 Color wheel error

Flashing Valid only when fan error indicated by Power LED flashing 6 times.

1 Power fan

2 Blower fan

3 Lamp fan or Optical fan

Contact your dealer for assistance.

Image Problems

Problem: No image appears on the screen

1. Verify the settings on your notebook or desktop PC.

2. Turn off all equipment and power up again in the correct order.

Problem: The image is blurred

1. Adjust the Focus on the projector.

2. Press the Auto button on the remote control or projector.

3. Ensure the projector-to-screen distance is within the 8-meter (26-feet) specified range.

4. Check that the projector lens is clean.

5. Make sure the output resolution from the PC is 800 x 600 (SVGA model) or 1024 x 768

(XGA model), the native resolution of the projector.

Problem: The image is wider at the top or bottom (trapezoid effect)

1. Position the projector so it is as perpendicular to the screen as possible.

2. Use the Keystone button on the remote control or projector to correct the problem.

Problem: The image is reversed or upside down

1. Check the Projection setting on the Utility menu of the OSD.

Problem: The image is streaked

– 31 –

D

L

P

r

o

j

e

c

t

o

r

—

D

L

P

r

o

j

e

L

P

c

P

r

o

j

e

c

1. Set the Frequency and Tracking settings on the Utility menu of the OSD to the default

2. To ensure the problem is not caused by a connected PC’s video card, connect to another

Problem: The image is flat with no contrast

1. Adjust the Contrast setting on the Main menu of the OSD.

Problem: The color of the projected image does not match the source image.

1. Adjust the Color Temperature and Gamma settings on the Main menu of the OSD.

U

t

o

r

—

U

t

o

r

—

U

settings.

computer.

Lamp Problems

Problem: There is no light from the projector

1. Check that the power cable is securely connected.

2. Ensure the power source is good by testing with another electrical device.

3. Restart the projector in the correct order and check that the Power LED is green.

4. If you have replaced the lamp recently, try resetting the lamp connections.

5. Replace the lamp module.

6. Put the old lamp back in the projector and have the projector serviced.

s

e

r

M

a

n

u

a

l

s

e

r

M

s

e

r

M

a

n

u

a

l

a

n

u

a

l

Problem: The lamp goes off

1. Power surges can cause the lamp to turn off. Press the power button twice to turn off the projector. When the Lamp Ready LED is on, press the power button.

2. Replace the lamp module.

3. Put the old lamp back in the projector and have the projector serviced.

Remote Control Problems

Problem: The projector does not respond to the remote control

1. Direct the remote control towards the remote sensor on the projector.

2. Ensure the path between remote and sensor is not obstructed.

3. Turn off any fluorescent lights in the room.

4. Check the battery polarity of the remote control.

5. Replace the batteries.

6. Turn off other Infrared-enabled devices in the vicinity.

7. Have the remote control serviced.

Audio Problems

Problem: There is no sound

1. Adjust the projector volume.

2. Adjust the volume of the audio source.

3. Check the audio cable connection.

4. Test the source audio output with other speakers.

5. Have the projector serviced.

Problem: The sound is distorted

1. Check the audio cable connection.

2. Test the source audio output with other speakers.

3. Have the projector serviced.

– 32 –

T

r

o

u

b

l

T

e

r

o

u

b

l

r

o

u

b

l

Having the Projector Serviced

If you are unable to solve the problem, you should have the projector serviced. Pack the projector in the original carton. Include a description of the problem and a checklist of the steps you took when trying to fix the problem. The information may be useful to the service personnel. Return the projector to the place you purchased it.

s

h

o

t

i

n

g

e

s

h

o

e

s

h

o

t

i

n

g

o

t

i

n

g

– 33 –

Specifications

SPECIFICATIONS

Power consumption < 350 watts < 280 watts < 350 watts < 280 watts Lamp

Display type TI DMD 0.7-inch, 12 deg. DDR TI DMD 0.55-inch, 12 deg. DDR Resolution XGA 1024 x 768 native SVGA 800 x 600 native Bandwidth Up to SXGA 1280 x 1024 @ 60 Hz Up to XGA 1024x 768 @ 60 Hz Color 16.7 Million (24-bits/pixel) Weight 3.55 kg (7.8 lbs) Projection distance 1.5 to 8 meter (4.9 to 26 feet) Projection screen size 0.94 to 6.1 meter (37 inches to 240 inches) Projection lens Manual zoom and focus Zoom ratio 1.2:1 Vertical keystone correction + / - 15 Projection methods Desktop front/rear; ceiling front/rear

XGA SVGA

250W

(ECO mode 200W)

200W

(ECO mode 160W)

250W

(ECO mode 200W)

200W

(ECO mode 160W)

Data Compatibility IBM PC or compatibles (VGA, SVGA), Mac HDTV Video Video compatibility NTSC/NTSC 4.43, PAL (B/G/H/I/M/N 60), SECAM H-Sync 15,31 - 70 kHz V-Sync 50 - 85 Hz Safety certification FCC Class B, UL, CUL, CE, CB, TUV-GS, CCC Operation temperature 10° ~ 35° Dimensions 32.8 x 23.8 x 8.8 cm (12.9 x 9.4 x 3.5 inches) Standby < 20 watts Noise 36 dB typical Audio speaker 2W mono speaker Uniformity 80 %

Input/output connectors

S

p

e

c

i

f

i

c

a

t

i

o

n

s

S

p

e

c

i

f

i

c

S

p

a

e

c

i

f

i

c

a

t

i

o

n

s

t

i

o

n

s

PC

Video

Audio

Service/upgrades RS-232 Security Kensington slot

DVI-I RGB in RGB out USB Composite video (RCAx1) S-Video (Mini-DIN) Component video Y,Pb/Cb,Pr/Cr (RCAx3) Mini-jack in Mini-jack out Right and left in (RCAx2)

– 35 –

D

L

P

r

o

j

e

c

t

o

r

—

U

s

e

r

M

a

n

u

a

l

D

L

P

r

o

j

e

c

t

o

r

—

U

s

e

r

L

P

r

o

j

e

c

t

o

r

—

U

M

s

e

r

M

a

n

u

a

l

a

n

u

a

l

Projection Distance versus Projection Size

A B

L Projection Distance

C

D

Projection

Distance

L

1.5m 1.14m 0.91m 0.68m 0.94m 0.75m 0.56m

4.92' 45" 36" 27" 36.88" 29.5" 22.1" 2m 1.52m 1.22m 0.91m 1.25m 1m 0.75m

6.56' 60" 48" 36" 49.18" 39.34" 29.51"

2.4m 1.83m 1.46m 1.1m 1.5m 1.20m 0.90m

7.87' 72" 57.6" 43.2" 59" 47.2" 35.4"

2.8m 2.13m 1.71m 1.28m 1.75m 1.4m 1.05m

9.18' 84" 67.2" 50.4" 68.85" 55.08" 41.31"

3.2m 2.44m 1.95m 1.46m 2m 1.6m 1.20m

10.5' 86" 68.8" 51.6" 70.49" 56.39" 42.29"

3.6m 2.74m 2.19m 1.65m 2.25m 1.80m 1.35m

11.81' 108" 86.4" 64.8" 88.52" 70.82" 53.11" 4m 3.05m 2.44m 1.83m 2.5m 2.00m 1.50m

13.12' 120" 96" 72" 98.36" 78.69" 59.02"

4.4m 3.35m 2.68m 2.01m 2.75m 2.2m 1.65m

14.43' 132" 105.6" 79.2" 108.19" 86.55" 64.91"

4.8m 3.66m 2.93m 2.19m 3.00m 2.40m 1.80m

15.74' 144" 115.2" 86.4" 118.03" 94.42" 70.82"

5.2m 3.96m 3.17m 2.38m 3.25m 2.60m 1.95m

17.06' 156" 124.8" 93.6" 127.86" 102.29" 76.72"

5.6m 4.27m 3.41m 2.56m 3.50m 2.80m 2.10m

18.37' 168" 134.4" 100.8" 137.7" 110.16" 82.62" 6m 4.57m 3.66m 2.74m 3.75m 3.00m 2.25m

19.68' 180" 144" 108" 147.54" 118.03" 88.52" 8m 6.10m 4.88m 3.66m 5.00m 4.00m 3.00m

26.24' 240" 192" 144" 196.72" 157.38" 118.03"

Diagonal Width Height Diagonal Width Height

Max. Screen Size Min. Screen Size

A C

B D

– 36 –

S

p

S

p

S

p

Timing Mode Table

The native resolution is 800 x 600 for the SVGA series and 1024 x 768 for the XGA series. Resolution other than native mode may display with uneven size of text or lines.

The following table shows the supported timing modes.

e

c

i

f

i

c

a

t

i

o

n

s

e

c

i

f

i

c

a

e

c

i

f

i

c

a

t

i

o

n

s

t

i

o

n

s

Signal Resolution

Frequency H.

( KHz )

NTSC -- 15.734 60.0 Ο -- --

PAL / SECAM -- 15.625 50.0 Ο -- --

VESA

640 x 350 37.9 85.1 -- Ο Ο

720 x 400 31.5 70.0 -- Ο Ο

720 x 400 37.9 85.0 -- Ο Ο

640 x 480 31.5 60.0 -- Ο Ο

640 x 480 37.9 72.8 -- Ο Ο

640 x 480 37.5 75.0 -- Ο Ο

640 x 480 43.3 85.0 -- Ο Ο

800 x 600 37.9 60.3 -- Ο Ο

800 x 600 46.9 75.0 -- Ο Ο

800 x 600 48.1 72.2 -- Ο Ο

800 x 600 53.7 85.1 -- Ο Ο

1024 x 768 48.4 60.0 -- Ο Ο

Frequency V.

Video Digital Analog

( Hz )

Apple Macintosh

HDTV

Ο

--

1024 x 768 56.5 70.1 -- Ο Ο

1024 x 768 60.0 75.0 -- Ο Ο

1024 x 768 68.7 85.0 -- Ο Ο

1280 x 1024 64.0 60.0 -- Ο Ο

640 x 480 35.0 66.7 -- Ο Ο

832 x 624 49.7 74.5 -- Ο Ο

1024 x 768 60.2 74.9 -- Ο Ο

1152 x 870 68.7 75.1 -- Ο Ο

1920 x 1080 33.8 60.0 Ο -- --

1920 x 1080 28.1 50.0 Ο -- --

1280 x 720 45.0 60.0 Ο -- --

720 x 576 31.3 50.0 Ο -- -- SDTV

720 x 480 31.5 60.0 Ο -- --

Frequency supported Frequency not supported

For XGA series only

– 37 –

D

L

P

r

o

j

e

c

t

o

D

L

P

r

L

o

P

r

j

e

c

t

o

r

j

e

c

t

o

Dimensions

r

—

U

s

e

r

M

a

n

u

a

l

s

e

r

M

s

e

r

M

a

n

u

a

l

a

n

u

a

l

32.8 cm (12.9 inches)

8.8 cm (3.5 inches) 23.8 cm (9.4 inches)

– 38 –

REGULATORY COMPLIANCE

FCC Warning

This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

Changes or modifications not expressly approved by the parties responsible for compliance could void the user’s authority to operate the equipment.

Canada

This class B digital apparatus complies with Canadian ICES-003.

Safety Certifications

UL, CUL, CB, TUV-GS, CCC

EN 55022 Warning

This is a Class B product. In a domestic environment, it may cause radio interference, in which case the user may be required to take adequate measures. The typical use is in a conference room, meeting room, or auditorium.