Features
■ Available in a variety of pin-out
confi gurations
VERSIONS
*RoHS COMPLIANT
AVAILABLE
■ Virtually infi nite electrical circuit isolation
■ Model 96 sealed for board wash
■ Metal or plastic shaft options
91, 92, 93, 94, 95, 96 - 5/8 ” Square Single-Turn Panel Control
97, 99 - 5/8 ” Square Single-Turn Panel Control with Rotary Switch
Potentiometer Specifi cations
Initial Electrical Characteristics1 Conductive Plastic Element Cermet Element
Standard Resistance Range
Linear Tapers (A, B, E, & H) .........................(B & E) 1 K ohms to 1 megohm ......................... (A & H) 100 ohms to 1 megohm
Audio Tapers (C, D, F, G, S, & T) .................(D,G,S, & T) 1 K ohms to 1 megohm ................. (C & F) 1 K ohms to 1 megohm
Total Resistance Tolerance ...............................10 % or 20 % .................................................... 5% or 10%
Independent Linearity .......................................±5 % .................................................................. ±5 %
Absolute Minimum Resistance .........................2 ohms maximum .............................................. 2 ohms maximum
Effective Electrical Angle ..................................(Linear tapers) 240 ° ± 5 ° .................................. (Linear tapers) 240 ° ± 6 °
(Audio tapers) 225 ° ± 5 ° .................................. (Audio tapers) 225 ° ± 6 °
Contact Resistance Variation ...........................±1 % .................................................................. ±1 % or 3 ohms (whichever is greater)
Dielectric Withstanding Voltage (MIL-STD-202, Method 301)
Sea Level ....................................................1,500 VAC minimum .......................................... 1,500 VAC minimum
70,000 Feet .................................................500 VAC minimum ............................................. 500 VAC minimum
Insulation Resistance (500 VDC) ......................1,000 megohms minimum ................................. 1,000 megohms minimum
Power Rating (Voltage Limited By Power Dissipation or 350 VAC, Whichever Is Less)
+70 °C Single Section Assembly ................(Linear tapers) 0.5 watt ...................................... (Linear tapers) 2 watts
(Audio tapers) 0.25 watt .................................... (Audio tapers) 1 watt
+70 °C Multiple Section Assembly .............(Linear tapers) 0.5 watt/section ......................... (Linear tapers) 1 watt/section
(Audio tapers) 0.25 watt/section ....................... (Audio tapers) 0.5 watt/section
+125 °C .......................................................0 watt ................................................................. 0 watt
Theoretical Resolution ......................................Essentially infi nite .............................................. Essentially infi nite
Environmental Characteristics
Operating Temperature Range .......................... -40 °C to +125 °C ................................................-40 °C to +125 °C
Storage Temperature Range .............................. -55 °C to +125 °C ................................................-55 °C to +125 °C
Temperature Coeffi cient Over Storage
Temperature Range .......................................... ±1,000 ppm/°C .....................................................±150 ppm/°C
Vibration (Single Section) ................................... 15 G ...................................................................... 15 G
Total Resistance Shift ................................... ±2 % maximum .................................................... ±2 % maximum
Voltage Ratio Shift ........................................ ±5 % maximum .................................................... ±5 % maximum
Shock (Single Section) ....................................... 30 G ......................................................................30 G
Total Resistance Shift ................................... ±2 % maximum .................................................... ±2 % maximum
Voltage Ratio Shift ........................................ ±5 % maximum .................................................... ±5 % maximum
Load Life ............................................................ 1,000 hours ..........................................................1,000 hours
Total Resistance Shift ................................... ±10 % maximum ..................................................±5 % maximum
Rotational Life (No Load) ................................... 100,000 cycles .....................................................100,000 cycles
Total Resistance Shift ................................... (Linear tapers) 10 ohms or ±15 % TRS max. ......(All tapers) ±5 % TRS max.
(whichever is greater)
(Audio tapers) ±20 % maximum
Contact Resistance Variation
@ 50,000 cycles ........................................... (Linear tapers) ±2 % ............................................. ±2 %
(Audio tapers) ±3 % ............................................. ±3 %
Moisture Resistance (MIL-STD-202, Method 103, Condition B)
Total Resistance Shift ................................... (Linear tapers) ±10 % TRS maximum .................(All tapers) ±5 % TRS maximum
(Audio tapers) ±20 % TRS maximum
Insulation Resistance (500 VDC) .................. 100 megohms minimum ......................................100 megohms minimum
IP Rating (Model 96) .......................................... IP 65 .....................................................................IP 65
(All Others) .................................................... IP 40 .....................................................................IP 40
1
*RoHS Directive 2002/95/EC Jan 27 2003 including Annex
Customers should verify actual device performance in their specifi c applications.
Specifi cations are subject to change without notice.
Additional Features
■ DPST and DPDT switch options
■ RoHS compliant versions available*
91, 92, 93, 94, 95, 96 - 5/8 ” Square Single-Turn Panel Control
97, 99 - 5/8 ” Square Single-Turn Panel Control with Rotary Switch
Potentiometer Specifi cations
Mechanical Characteristics
Stop Strength (1/4 ” D shaft) .............................................................................................................................................45.19 N-cm (4 lb.-in.)
(1/8 ” D shaft) .............................................................................................................................................33.89 N-cm (3 lb.-in.)
Mechanical Angle ................................................................................................................................................................................. 300 ° ±5 °
Torque
Starting ........................................................................................................................................... 0.3 max. above average running torque
Running Torque
Single or Dual Section (A ,D & R Bushings) .............................................................................................. 0.21 to 1.06 N-cm (0.3 to 1.5 oz.-in.)
Single or Dual Section (C & U Bushings) .................................................................................................. 0.14 to 1.06 N-cm (0.2 to 1.5 oz.-in.)
Mounting .................................................................................................................. (Metal Bushing) 1.7-2.0 N-m (15-18 lb.-in.) maximum
Plastic Bushing) 56-79 N-cm (5-7 lb.-in.) maximum
Variation ...................................................................................................................... 0.35 N-cm (0.5 oz.-in.) maximum in 45 ° shaft travel
Weight (Single Section, Plastic Bushing) ............................................................................................................................... 7.3 grams nominal
Weight (Single Section, Metal Bushing) ...............................................................................................................................12.7 grams nominal
(Each Additional Section) ....................................................................................................................................................4 grams nominal
Terminals .................................................................................................................................Printed circuit terminals, J-Hooks or solder lugs
Soldering Condition ...........................................Recommended hand soldering using Sn95/Ag5 no clean solder, 0.025 ” wire diameter.
Maximum temperature 399 °C (750 °F) for 3 seconds. No wash process to be used with no clean fl ux.
Marking ..................................................................................Manufacturer’s trademark, date code, resistance, manufacturer’s part number
Ganging (Multiple Section Potentiometers) .............................................................................................................................2 cups maximum
Hardware ...................One lockwasher and one mounting nut is shipped with each potentiometer, except where noted in the part number.
1
NOTE: All Model 90 performance specifi cations do not apply to units subjected to printed circuit board cleaning procedures, except
for the sealed version (Model 96).
1
At room ambient: +25 °C nominal and 50 % relative humidity nominal, except as noted.
Specifi cations are subject to change without notice.
Customers should verify actual device performance in their specifi c applications.
91, 92, 93, 94, 95, 96 - 5/8 ” Square Single-Turn Panel Control
97, 99 - 5/8 ” Square Single-Turn Panel Control with Rotary Switch
Rotary Switch Specifi cations
Initial Electrical Characteristics
1
Contacts:
DPST ........................................................................................................................................................N.O/N.O., N.C./N.C. or N.O./N.C.
DPDT ..........................................................................................................................................................2 N.O./N.C. (break before make)
Power Rating (Resistive Load):
DPST ..................................................................................... 2 A @ 125 volts RMS-60 Hz or 2 A @ 28 VDC, 1 A @ 250 volts RMS-60 Hz
DPDT .....................................................................................................................................1 A @ 125 volts RMS-60 Hz or 1 A @ 28 VDC
Contact Resistance (0.1 VDC-10 mA) ...............................................................................................................................10 milliohms nominal
Contact Bounce ...........................................................................................................................................................5 milliseconds maximum
Dielectric Withstanding Voltage (MIL-STD-202, Method 301)
Sea Level ........................................................................................................................................................................1500 VAC minimum
Insulation Resistance ................................................................................................................................................. 1000 megohms minimum
Environmental Characteristics
1
Operating Temperature Range .................................................................................................................................................... 0 °C to +70 °C
Exposure Temperature Range ................................................................................................................................................-65 °C to +125 °C
Vibration (Dual Section).................................................................................................................................................................................. 8 G
Contact Resistance .................................................................................................................................................. 10 milliohms maximum
Contact Bounce ................................................................................................................................................... 0.1 millisecond maximum
Shock (Dual Section).................................................................................................................................................................................... 20 G
Contact Resistance .................................................................................................................................................. 10 milliohms maximum
Contact Bounce ................................................................................................................................................... 0.1 millisecond maximum
Rotational Life ................................................................................................................................................................................25,000 cycles
Switch Actuating Torque (50% Duty cycle @ Rated Power Load) ........................................................... 1.41 to 4.94 N-cm (2 to 7 oz.-in.)
Contact Resistance ................................................................................................................................................ 100 milliohms maximum
Moisture Resistance (MIL-STD-202, Method 106, Condition B)
Contact Resistance (0.1 VDC-10 mA) ..................................................................................................................... 10 milliohms maximum
Insulation Resistance (After 24 Hours @ Room Temperature) (500 VDC) ..............................................................100 megohms minimum
Housing Material .......................................................................................................High temperature, fl ame retardant, thermosetting plastic
Mechanical Characteristics
1
Actuating Torque (Each Section, Switch Module Only) .............................................................................. 3.53 to 10.59 N-cm (5 to 15 oz.-in.)
Running Torque (Out of Detent, 2-4 Module Assembly) ............................................................................. 0.21 to 1.41 N-cm (0.3 to 2 oz.-in.)
Detent ................................................................................................................................................................................CW or CCW standard
Actuation Angle ......................................................................................................................................................................................20 ° ±5 °
Contact Materials .................................................................................................................................................... Fine silver with gold overlay
Terminal Styles .............................................................................................................................................................................Solder lug only
Standard Orientation ........................................................................................................................................ In-line with control terminals
Optional ....................................................................................................................................................Rotated 90 ° CCW from standard
Terminal Strength (Before and After Soldering Heat Exposure) .................................................................................... 0.9 kg (2 lbs.) minimum
NOTE: Model 99 performance specifi cations do not apply to units subjected to printed circuit board cleaning procedures.
1
At room ambient: +25 °C nominal and 50 % relative humidity nominal, except as noted.
Customers should verify actual device performance in their specifi c applications.
Specifi cations are subject to change without notice.
91, 92, 93, 94, 95, 96, 97, 99 - 5/8 ” Square Single-Turn
Product Dimensions
Model 91 & 96 PC Pin Terminals, In-Line
22.86 ± .43
(.90 ± .017)
12.7
(.50)
10.16
(.40)
.79 ± .41
(.031 ± .016)
9.53 ± .38
(.375 ± .015)
6.35 ± .38
(.250 ± .015)
SEE DETAIL
FOR
SHAFT OPTIONS
11.05 ± .20
(.435 ± .008)
15.88 ± .38
(.625 + .015)
(STYLE A)
(STYLE C)
2.36
(.093)
15.29 ± .56
(.602 ±.022)
(MODEL 91 ONLY)
2.54
(.100)
1.37
(.054)
1
2
3
.81
(.032)
2.54
(.100)
Model 93 PC Pin Terminals, "L" Pattern
5.97 ± .38
(.235 ± .015)
2
5.08 ± .38
(.20 ± .015)
11.05 ± .20
(.435 ± .008)
TYP.
.81
(.032)
DIA. TYP.
10.16 ± .30
(.40 ± .012)
1
1
2
3
Model 95 Solder Lug Terminals, "Triangular" Pattern
5.08 ± 1.02
(.200 ± .040)
13
4.45 ± .38
(.175 ± .015)
2
5.59 ± .20
(.220 ± .008)
2.54
(.100)
2.54
(.100)
4.45 ± .38
(.175 ± .015)
10.16
(.40)
2
31
13.72
(.54)
15.88 ± .38
(.625 ± .015)
9.53 ± .38
(.375 ± .015)
DIA.
12.7 ± 1.02
(.50 ± .040)
5.08
(.20)
2.03
(.080)
3 PLCS.
Model 92 J-Hooked
Terminals, In-Line
DIA.
321
5.08
(.20)
Model 94 J-Hooked
Terminals, "L" Pattern
321
.81
(.032)
R. MAX.
(.150)
MAX. TYP.
Bushing Styles
3/8 THREADLESS (9.53 mm) (STYLE "D")
3/8-32 UNEF (9.53 mm) (STYLE "A")
1/4-32 UNEF (6.35 mm) (STYLE "C")
M10 X 0.75-6g (STYLE "R")
M7 X 0.75-6g (STYLE "U")
.41
(.016)
WIDE X
3 PLCS.
2.29
(.090)
LONG
1.02
(.040)
3.81
.79
(.031) 2 PLCS.
5.33 ± .76
(.21 ± .03)
1.52
(.06)
Model 97 1st Cup Same As Model 93
(2nd Cup - Switch)
2.77 ± .38
(.109 ± .015)
MOUNTING
SURFACE
.254
(.010)
GAP
16.89 ± .51
(.665 ± .020)
2.29
6 PLCS.
(.090)
1.52
(.06)
GAP
2.77 ± .38
(.109 ± .015)
Model 99 1st Cup Same As Model 95
(2nd Cup - Switch)
24.77 ± .51
2.77 ± .38
(.109 ± .015)
MOUNTING
SURFACE
5.59 ± .38
(.022 ± .015)
16.89 ± .51
(.665 ± .020)
4.45 ± .38
(.175 ± .015)
(.975 ± .020)
1
2 3
Switch Module Variations
Shaft Flat Orientation
120 ° ± 5 ° STD.
FLAT ORIENTATION
(SHAFT AT CCW END)
TOTAL ROTATION 300 °
2.41 X 1.14
(.095 ± .045)
2.54 ± 0.25
(.100 ± .010)
8.26 ± 0.25
(.325 ± .010)
2.41 X 1.14
(.095 ± .045)
2.29
(.090)
2.77 ± .38
(.109 ± .015)
1
CCW
15.88
(.625)
REF.
31
2654
SLOT 6 PLCS
2 PLCS.
15.88
(.625)
REF.
31
2654
SLOT 6 PLCS
6 PLCS.
3
2
POTENTIOMETER
TOLERANCES EXCEPT AS SHOWN: DECIMAL .XXX ±
.128
FRACTION ± 1/64
(.015 )
.005
.XX ±
ANGLE ±5 °
(.38)
DIMENSIONS:
(INCHES)
MM
Specifi cations are subject to change without notice.
Customers should verify actual device performance in their specifi c applications.
CCW DETENT
25 ° MAX.
ACTUATION
ANGLE
(TYPES 51,
53, 55, 57, 59,
61, 71, 73)
3
1
DPST (NO/NC)
(TYPES 50, 51, 56, 57)
NOTE: Switch terminals shown in vertical position.
4
3
1
2
DPST (NC/NC)
(TYPES 54, 55, 60, 61)
4
3
2
1
DPST (NO/NO)
Switch contacts shown in detent position.
(TYPES 52, 53, 58, 59)
CW DETENT
25 ° MAX.
ACTUATION ANGLE
(TYPES 50, 52, 54,
56, 58, 60, 70, 72)
4
3
2
1
DPDT (NC/NC)
(TYPES 70, 71, 72, 73)
4
5
6
2
91, 92, 93, 94, 95, 96, 97, 99 - 5/8 ” Square Single-Turn
Product Dimensions
Plastic
Shaft
Styles
Metal
Shaft
Styles
SHAFT TYPE "B" (USES BUSHING A OR D) SHAFT TYPE "D" (USES BUSHING C)
1.60+.38/-.00
(.063+.015/-.000)
STD. LENGTHS:
12.70
15.88
(.500)
(.625)
1.19
(.047)
19.05
(.750)
6.32+.000/-.152
(.249+.000/.006)
DIA.
22.23
(.875)
13.16+.00/-.15
(.1245+.000/-.006)
STD. LENGTHS:
12.70
15.88
(.500)
(.625)
DIA.
19.05
(.750)
SHAFT TYPE "T" (USES BUSHING U)
1.50 ± .25
(0.06 ± .001)
3.988 +0.000/-0.051
STD. LENGTHS:
12.00
(.472)
(0.03)
16.00
(.630)
.79
(.157 +.000/-.002)
22.00
(.866)
DIA.
SHAFT TYPE "C" (USES BUSHING A OR D) SHAFT TYPE "R" (USES BUSHING R) SHAFT TYPE "W" (USES BUSHING A OR D)
STD. LENGTHS:
22.23
(.875)
5.49
(.216)
11.18 ± .38
(.440 ± .015)
6.30+.000/-.152
(.248+.000/.006)
DIA.
1.80 ± .25
(0.07 ± .001)
STD. LENGTHS:
16.0
(.630)
19.0
(.748)
22.0
(.866)
5.994 +0.000/-0.051
(.236 +.000/-.002)
1.00
(.04)
DIA.
48 TOOTH
STD. LENGTHS:
25.40
(1.00)
14.27 ± .25
(.562 ± .010)
6.31+.025/-.051
(.2485+.001/.002)
DIA.
SHAFT TYPE "A" (USES BUSHING A) SHAFT TYPE "H" (USES BUSHING A) SHAFT TYPE "V" (USES BUSHING U)
12.70
(.500)
STD. LENGTHS:
15.88
(.625)
19.05
(.750)
6.32+.010/-.025
(.2490+.0004/.0010)
DIA
22.23
25.4
(1.000)
(.875)
“F” ± .38
(“F” ± .015)
12.70
(.500)
1.60
(.063)
5.486 ± .051
(.216 ± .002)
STD. LENGTHS:
15.88
19.05
(.625)
(.750)
FLAT LENGTH “F”:
4.78
7.95
(.188)
(.313)
6.32+.010/-.025
(.2490+.0004/.0010)
DIA
22.23
25.4
(1.000)
(.875)
11.13
14.30
(.438)
(.563)
1.50 ± 0.25
(.059 ± .010)
0.79 ± 0.13
(.031 ± .054)
STD. LENGTHS:
12.0
(.472)
(.630)
16.0
(.1571+.0000/.0010)
19.0
(.748)
3.99+.000/-.035
DIA
22.0
(.866)
SHAFT TYPE "G" (USES BUSHING A)
1.60+.38/-.00
(.063+.015/-.000)
1.194
(.047)
12.70
(.500)
DIMENSIONS:
(INCHES)
STD. LENGTHS:
15.88
(.625)
MM
19.05
(.750)
6.32+.010/-.025
(.2490+.0004/.0010)
22.23
(1.000)
(.875)
25.4
DIA.
SHAFT TYPE "J" (USES BUSHING R)
1.80 ± 0.25
(.071 ± .010)
1.00 ± 0.13
(.039 ± .054)
STD. LENGTHS:
12.0
16.0
(.472)
(.630)
TOLERANCES EXCEPT AS SHOWN: .XX = ±
19.0
(.748)
(.2362+.0000/.0010)
22.0
(.866)
.XXX = ±
.XXXX = ±
Customers should verify actual device performance in their specifi c applications.
6.00+.000/-.035
DIA
.02
(.050)
.005
(.127)
.0005
(.0127)
SHAFT TYPE "Y" (USES BUSHING A)
9.12
1.27
(.050)
21 °
STD. LENGTHS:
19.05
(.750)
(.359)
5.87
(.231)
8.74
(.344)
.762
(.030)
5.03 ± .05
(.198 ± .002)
1.57
(.062)
5.97
(.235)
DIA.
DIA.
Specifi cations are subject to change without notice.
How to Order 90 Series Panel Controls
9 1 A 2 A - A 2 8 - A 1 5 / A15 L
9 9 A 2 A - B 2 8 - A 1 5 / R51 L
Models 91 - 96: Part number for multiple section
potentiometers must have a taper and resistance value for
each section.
Models 97 & 99: Part number must contain a switch type.
ANTI-ROTATION LUG
A Single .305 ” (7.8 mm) R,
90 °CW
C Single .305 ” (7.8 mm) R,
270 °CW
D No Lug
# SECTIONS APPLICABLE MODELS
1 Single Models 91 Thru 96 Only
2 Dual All Models, 2nd Section is
a Switch in Model 99
A Metal Plain 3/8 ” (9.53 mm) D x 3/8 ” (9.53 mm) L
C Metal Plain 1/4 ” (6.35 mm) D x 1/4 ” (6.35 mm) L
D Plastic Unthreaded 3/8 ” (9.53 mm) D
x 3/8 ” (9.53 mm) L
R Metal Plain 10 mm D x 9 mm L
U Metal Plain 7 mm D x 9 mm L
91 Single-Turn, In-Line PC Pins
92 Single-Turn, In-Line J-Hooks
93 Single-Turn, L-Pattern PC Pins
94 Single-Turn, L-Pattern J-Hooks
95 Single-Turn, Triangle-Pattern Solder Lugs
96 Single-Turn, In-Line PC Pins, Sealed*
97 Single-Turn, L-Pattern PC Pins w/Switch
99 Single-Turn, Triangle-Pattern
Solder Lugs w/Switch
*Model 96 is not available in multi-gang versions.
AVAILABLE ONLY IN
SHAFT TYPE
(CODE) (CODE)
B Plastic Single Slotted 1/4 " (6.35 mm) D 16,20,24,28 A,D
C Plastic Single Flatted 1/4" (6.35 mm) D 24,28 A,D
D Plastic Single Plain 1/8" (3.18 mm) D 16,20,24 C
R Plastic Single Slotted 6 mm D Metric 16,19,22 R
T Plastic Single Slotted 4 mm D Metric 16,19,22 U
W Plastic Single Knurled 1/4" (6.35 mm) D 32 A,D
A Metal Single Plain 1/4" (6.35 mm) D 16,20,24,28,32 A
G Metal Single Slotted 1/4" (6.35 mm) D 16,20,24,28,32 A
H Metal Single Flatted 1/4" (6.35 mm) D 16,20,24,28,32 A
J Metal Single Slotted 6 mm D Metric 12,16,19,22 R
V Metal Single Slotted 4 mm D Metric 12,16,19,22 U
Y Metal Single Knurled 1/4" (6.35 mm) D 24 A
BUSHING
MODEL
LENGTHS BUSHINGS
SHAFT AVAILABLE
LENGTH ONLY IN
(FMS) BUSHING
Code Description Code
16 1/2 ”L A, C, D
20 5/8 ”L A, C, D
24 3/4 ”L A, C, D
28 7/8 ”L A, D
32 1 ”L A, D
12 12 mmL U
16 16 mmL R, U
19 19 mmL R
22 22 mmL R, U
METRIC
RoHS IDENTIFIER
Compliant
L
Non-Compliant
Blank
SWITCH TYPE (MODELS 97 & 99 ONLY)
(R50) DPST N.O./N.C. CW Detent In-Line Term
(R51) DPST N.O./N.C. CCW Detent In-Line Term
(R52) DPST N.O./N.O. CW Detent In-Line Term
(R53) DPST N.O./N.O. CCW Detent In-Line Term
(R54) DPST N.C./N.C. CW Detent In-Line Term
(R55) DPST N.C./N.C. CCW Detent In-Line Term
(R56) DPST N.O./N.C. CW Detent Horz Term
(R57) DPST N.O./N.C. CCW Detent Horz Term
(R58) DPST N.O./N.O. CW Detent Horz Term
(R59) DPST N.O./N.O. CCW Detent Horz Term
(R60) DPST N.C./N.C. CW Detent Horz Term
(R61) DPST N.C./N.C. CCW Detent Horz Term
(R70) DPDT CW Detent In-Line Term
(R71) DPDT CCW Detent In-Line Term
(R72) DPDT CW Detent Horz Term
(R73) DPDT CCW Detent Horz Term
ELEMENT TAPER RESISTANCE CODE
TYPE/TOLERANCE VALUE IN OHMS
(A) Linear Cermet ±10 % (05) - 100 (30) - 15 K
(H) Linear Cermet ±5 % (28) - 150 (16) - 20 K
(06) - 200 (17) - 25 K
(07) - 250 (18) - 50 K
(08) - 500 (19) - 75 K
(09) - 750 (20) - 100 K
(10) - 1 K (31) - 150 K
(29) - 1.5 K (21) - 200 K
(11) - 2 K (22) - 250 K
(12) - 2.5 K (23) - 500 K
(13) - 5 K (24) - 750 K
(14) - 7.5 K (25) - 1 M
(15) - 10 K
(B) Linear C-P ±20 % (10) - 1 K (18) - 50 K
(E) Linear C-P ±10 % (12) - 2.5 K (20) - 100 K
(13) - 5 K (22) - 250 K
(15) - 10 K (23) - 500 K
(16) - 20 K (25) - 1 M
(17) - 25 K
(C) CW Audio Cermet ±10 % (10) - 1 K (18) - 50 K
(D) CW Audio C-P ±20 % (12) - 2.5 K (20) - 100 K
(F) CCW Audio Cermet ±10 % (13) - 5 K (22) - 250 K
(G) CCW Audio C-P ±20 % (15) - 10 K (23) - 500 K
(S) CW Audio C-P ±10 % (17) - 25 K (25) - 1 M
(T) CCW Audio C-P ± 10 %
Boldface features are Bourns standard options.
All others are available with higher minimum order
quantities.
REV. 02/10
Specifi cations are subject to change without notice.
Customers should verify actual device performance in their specifi c applications.
Loading...