Page 1
Page 2
Introduction
Thank you for choosing Boss Marine as your source for
entertainment! The MRBT200 Marine Bluetooth Speaker will
provide you with years of listening enjoyment. Its rugged, and
certified water resistance is built to handle the outdoors and
marine environment.
MRBT200 Description:
9
1 2 3 4
5 6 7 8
10
11
Page 3
1.ON/OFF button 2.Play/Pause/Phone
(Reset/press and hold 2 seconds twice)
3.Previous/Volume – 4.Next/Volume +
5.MIC
7.Green LED(Power)
9.AUX in Port
6.Blue LED(Bluetooth)
8.Red LED(Charging)
10.Micro USB Charging Port
11.NFC
Included:
1.Boss Marine MRBT200 Speaker
2.USB Micro Charging Cable
3.3.5 mm Audio Cable
4.Carabineer clip
5.Warranty Card
6.User Manual
Specifications
Supported Profiles: A2DP, HFP, AVRCP
Bluetooth Version/Range: v2.1, 33ft (10m)
NFC: For Simplified Bluetooth Pairing
Dimensions: 7" x 3" (176 mm x 76 mm)
Battery: Li-Ion 3.7V, 1200 mAh
Charging: 5V @ 500 mA
Up to 8 Hours of Playback
Page 4
Operation
Powering On
Press and Hold "ON/OFF" button 2 seconds to power ON, the
Blue LED will start to flash, while the Green LED stays
illuminated.
If an Aux (3.5 mm) cable is connected to the MRBT200, the
Blue LED will turn off, and the Green LED will stay illuminated,
notifying you, the MRBT200 is in Aux-In mode
.
Powering Off
Press and Hold "ON/OFF" button 2 seconds to power OFF
Bluetooth Mode
Pairing
The unit will automatically go into “Pairing Mode” when it is
powered ON.
Go into your Bluetooth device settings menu and look for
“BOSS MARINE”
After the unit has paired and connected, it will re-connect
automatically when the MRBT200 is powered on and the device
is in range.
Note: Bluetooth Timeout :30 minutes
Begin Streaming Music
” to start playing music Press “
” 2 seconds to play the next track
” 2 seconds to play previous track
Press and Hold“
Press and Hold“
Press either “ ” or “ ” for volume control
Making and Receiving Phone Calls
When the MRBT200 is connected and paired to your device,
the MRBT200 allows you to make or receive phone calls with its
built-in microphone.
Press “ ” to accept a call
To end a call press“ ”
To place a call, simply dial the number or select a contact from
your Bluetooth device and call
To reject a call, press and hold “ ” for 2 seconds
Page 5
Aux-In Mode
Plug in the supplied 3.5 mm cable into the MRBT200. The other end
is connected to your device. The Green LED will only illuminate
when in “Aux” mode.
Please note music and volume can be controlled by your device.
Charging
Attach the USB cable to the MRBT200, and plug into any USB
charger. If the unit is completely discharged, it will take
approximately 4 hours to fully charge.
The Red LED will illuminate during charging, when it has completed,
the Red LED will turn off.
Note:There will be a beep when the battery is low and needs to be
recharged.
LED Status
Blue LED flashing & Green LED solid Bluetooth Mode
Green LED on solid
Red LED
Aux Mode, Charging Completed
Charging
Troubleshooting
The MRBT200 doesn’t connect
to device
Speaker needs to be connected/
re-paired to device
A tone is heard every few seconds Speaker needs to be charged
The MRBT200 will not power on
Speaker needs to be charged
The MRBT200 doesn’t control
track(s)/volume
Speaker needs to be in Bluetooth
mode for full control
The MRBT200 distorts at
high volume
The devices’ volume needs to
be lowered
Discover various marine electronics and navigation in our online store.
Loading...