Page 1
Page 2
CONTENTS
Congratulations on your purchase of a
33bE
Audio Systems
Compact Disc Receiver. This product has been designed and
built to deliver the highest quality audio reproduction. We are
sure you'll enjoy listening to your favorite music with this
33bE
component as part of your car audio system. For best
results please consult a professional mobile electronics installer
for application advice or troubleshooting.
To guarantee top
performance we recommend using The
33bE
Link installation
accessories such as RCA interconnects, power cables, and
speaker wire. Thank you for choosing
33bS
Audio Systems
products for your mobile entertainment system. We can't change
the world, but we can make it sound better.
Installation
.....................................................................................................
4
DIN Front-Mount (Method
A)
..................................................................................
4
Installing the unit
...............................................................................................
4
Removing the unit
.............................................................................................
5
...................................................................................
DIN Rear-Mount (Method
6)
5
..............................................................
Using the Detachable Front Panel
6
1
Wiring Connection
........................................................................................ 7
.......................................................................................................
Operation
8
..................................................................................................
General Operation
8
Radio Operation
......................................................................................................
9
...........................................................................................
CD
or
CDC
Operation 10
.........................................
....................................................
Specification
12
Trouble Shooting
.........................................................................................
13
Page 3
Notes:
Your MR-1200R was designed for use
in marine applications such as in a
boat. It will also work in cars, trucks,
off road vehicles, etc.
Choose the mounting location where
the unit will not interfere with the
normal driving function of the driver.
Before finally installing the unit,
connect the wiring temporarily and
make sure it is all connected properly
and the unit and the system work
properly.
Use only the parts included with the
unit to ensure proper installation.
The use of unauthorized parts can
cause malfunctions.
Consult with your nearest dealer if
installation requires the drilling of holes
or other modifications to the boat or
the vehicle.
Install the unit where it does not get in
the driver's way and cannot
injure,the
passenger if there is a sudden stop,
like an emergency stop.
If installation angle exceeds 30efrom
horizontal, the unit might not give its
optimum performance.
Avoid installing the unit where it would
be subject to high temperature, such
as from direct sunlight, or from hot air,
from the heater, or where it would be
subject to dust, dirt or excessive
vibration.
DIN FRONTIREAR-MOUNT
This unit can be properly installed either
from "Front" (conventional DIN
Frontmount) or '.'Rearw (DIN Rear-mqunt
installation, utilizing threaded screw holes
at the sides of the unit chassis).
For details, refer to the following
illustrated installation methods.
DIN
FRONT-MOUNT (Method
A)
Installing the unit
1.
Dashboard
2.
Mounting Bracket
After inserting the mounting bracket
holder into the dashboard, select the
appropriate tab according of the
dashboard material and bend them
inwards to secure the mounting
bracket holder in place.
3. Screw
1. Dashboard
2.
Nut (5mm)
3.
Spring washer
4. Screw (5 x
25mm)
5. Screw
6.
Strap
Be sure to use the strap to secure the
back of the unit in place. The strap
can be bent by hand to the desired
angle.
7.
Plain washer
!
Removing the unit
1.
Frame
2. Insert fingers into the groove in the
front of frame and pull out to remove
the frame. (When reattaching the
frame, point the side with a groove
downwards and attach it.)
3.
Lever
Insert the levers supplied with the unit
into the grooves at both sides of the
unit as shown in figure until they click.
Pulling the levers makes it possible to
remove the unit from the dashboard.
DIN
REAR-MOUNT (Method
B)
Installation using the screw holes on the
sides of the unit.
Fastening the unit to the factory radio
mounting bracket.
1. Select a position where the screw
holes of the bracket and the screw
holes of the main unit become aligned
(are fitted), and tighten the screws at
2
places on each side.
Use either truss screws
(5
x 5mm) or
flush surface screw (4 x
5mm),
depending on the shape of the screw
holes in the bracket.
2. Screw
3.
Factory radio mounting bracket
4. Dashboard or Console
5.
Hook (Remove this part)
Note:
The mounting box, outer trim ring,
and half-sleeve are not used for method
B installation.
Page 4
ABLI (RONT PANEL
c
!
To Detach the Front pafine'
To Reinstall the Front Panel
1.
Press the
open
button
8
Pnd the fr
1.
Push the front panel into the main
t
panel will flip down.
body. A 'click' sound should be
heard.
Open
&
2.
Remove the front panel
graspirfl!
in the middle and pulling
,tb toward
,,.
2.
Note that if the front panel fails to lock
in
Dosition ~ro~erlv, Dress control
bu'tton mai not fuiction and display
may be missing some segments.
Pressing the
OPEN
button and then
ceinstall the front panel again.
Front
Panel
ecautions when Handling
3,
For
safekeeping,
store
tp&
front
p:i
1.
Do not drop the front panel.
in the supplied protectivo
immediately
aher
being
reWnoved.
2. Do not put pressure on the display or
control buttons when detaching or
-
reinstalling the front panel.
Protective
Case
3.
Do not touch the contacts on the front
panel or on the main unit body. It may
result in poor electrical contact.
4.
If any dirt or foreign substances
adhered on the contacts, they can be
Front
Panel
removed with a clean and dry cloth.
4.
Push
the
front
metal
"nto the
5.
Do not expose the front panel to high
main
body. A 'click'
souoOd shouldh
temperatures or direct sunlight in
anywhere.
heard.
6.
Keep away any volatile agents (e.g.
benzene, thinner, or insecticides) from
touching the surface of the front panel.
7.
Do not attempt to disassemble the
front panel.
WIRING CONNECTION
I
MAIN
UNIT
I
L
ANTENNACONNECTOR
MEMORY YELLOW
BACK-UP
e
11
11111111
111
GROUND
(B-)
BLACK
1
[
AUX INPUT
Rch RED
Lch WHITE
111
IRROWM
>-.
.
-
. .
.
.
,
FRONT RCA CABLE Rch RED
LCh WHITE
POWER BLUE
ANTENNA
Lch WHITE
;.
2-SPEAKERS SYSTEM.
..,..--
4-SPEAKERS SYSTEM
-...,I I 1 11
I I I,.---
4-SPEAKERS SYSTEM
.-...,.
2-SPEAKERS SYSTEM
...
GREEN
Note:
1.
For 2-speakers system, green, violet, white/black and grey/black wire leads are
unconnected and isolated.
2.
For 2-speakers system, keep the fader indicator at center position to maintain the
existing volume level.
Page 5
Page 6
Page 7
Loading...