Boss Audio Systems BV9978T User Manual

To ensure safety while driving

and to comply with laws,

drivers should not watch video or

operate the video device while driving.

-1-

Content

Precaution......................................

Safety Information.........................

Disc Note.......................................

Installation ....................................

Electric Connection ......................

Remote Control ............................

Basic Operation ............................

Loading/Ejecting a DISC .................

Open/Close Monitor and Angle

Adjustment......................... ........

Main Menu Operation......................

Setting animation...........................

Setting disc....................................

Setting radio...................................

Setting TV.......................................

Setting wallpaper............ ................

Version about..................................

Setting time.......... .........................

Setting audio mode.........................

Setting video mode.........................

Setting OSD language....................

Setting

illumination color.................

TFT display calibration. ..................

Rear View Camera ........................

Control Panel ................................

Unit keys ........................................

Radio Operation............................

Listening to the radio ......................

Storing and Listening to a memory

station ........................................

18

19

20

21

23

24

25

26

27

28

29

30

31

32

33

2

3

4

5

7

8

10

11

12

13

14

17

Automatic Memory Storing &

Program Scanning.......................

Media Operation.............................

Basic Operation ..............................

Selecting Play Mode ........................

On-Screen Display Function .............

Digital Video

Special Function........

Multi-Subtitle Language function.......

Multi-audio language Function..........

Multi-angle Function........................

Tit le menu function ..........................

A-B Repeat function.........................

Program function.............................

Step function...................................

Slow speed function.........................

TV operation..................................

AUX Operation ...............................

AV Operation..................................

USB Operation ...............................

Card Operation ..............................

SWC Operation..............................

Parental Control............................

Region Code..................................

Specification .................................

Troubleshooting.............................

-2-

Precaution

THANK YOU FOR PURCHASING PLAYER .

Before operating the unit, read this manual thoroughly and keep it handy for future reference . To avoid injury or accident , read the following precautions before installing and operating the unit .

A BOSS AUDIO MULTIMEDIA

ABOUT THE LIQUID CRYSTAL DISPLAY (LCD) PANEL

Do not press on the LCD panel on the unit as doing so can distort the picture or cause a malfunction . The picture may become unclear , or the LCD panel may be damaged .

NOTES ON CLEANING

-Clean the LCD panel with a slightly damp soft cloth.

-Do not use solvents such as benzine, thinner, commercially available cleaners or antistatic spray .

- Do not use alcohol to clean the screen .

If your car was parked in a cold or hot place, the picture may not be clear . The monitor is not damaged . The picture will become clear the temper ature in your car becomes normal .

DO NOT install any receiver in locations where;

- it may obstruct the steering wheel and gearshift lever operations, as this may result in a traffic accident.

- it may obstruct the operation of safety devices such as air bags, as this may result in a fatal accident.

- it may obstruct visibility. DO NOT operate any receiver while manipulating the steering wheel, as this may result in a traffic accident. The driver must not watch the monitor while driving. IF THE DRIVER watches the monitor while driving, it may lead to carelessness and cause an accident. IF YOU NEED to operate the receive while driving, be sure to look ahead carefully or you may be involved in a traffic accident. IF THE PARKING BRAKE is not engaged.“ ParkingBrake” flashes on the monitor, and no playback picture will be shown.

- This warning appears only when the parking brake wire is connected to the parking brake system built in the car ( refer to the electric connection)

ON INSTALLATION

-3-

Safety Information

CAUTION:

THIS DIGITAL VIDEO PLAYER IS A CLASS I LASER PRODUCT. HOWEVER THIS DIGITAL VIDEO PLAYER USES A VISIBLE/INVISIBLE LASER BEAM WHICH COULD CAUSE .

HAZARDOUS RADIATION EXPOSURE IF DIRECTED. BE SURE TO OPERATE THE DIGITAL VIDEO PLAYER CORRECTLY AS INSTRUCTED.

USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.DO NOT OPEN COVERS AND DO NOT REPAIR YOURSELF. REFER SERVICING TO QUALIFIED PERSONNEL.

WARNING:

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE.

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, AND ANNOYING INTERFERENCE, USE ONLY THE RECOMMENDED ACCESSORIES.

THIS DEVICE

IS INTENDED FOR CONTINUOUS OPERATION.

This product incorporates copyright protection technology that is protected by method claims of certain U.S. Patents and other intellectual property rights owned by Macrovision Corporation and other rights owners.Use of this copyright protection technology must be authorized by

Macro vision Corporation, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision Corporation. Reverse engineering or disassembly is prohibited.

REGION MANAGEMENT INFORMATION:

This Digital Video Player is designed and manufactured to respond to the Region Management Information that is recorded on a Digital Vid eo disc. If the Region number described on the Digital Vi de o disc does not correspond to the Region number of this

Digital Video Player, this Digital Video Player cannot play this disc.

-4-

Disc Note

Preparing New Discs with Rough Spots

A new disc may have rough edges on its inside and outside edges. If a disc with rough edges is used, the proper setting will not be performed and the player will not play the disc. Therefore, remove the rough edges in advance by using a ball point pen or pencil

as shown on the right. To remove the rough edges, press the side of the pen or pencil against the inside and outside edges of the disc.

Rough spots on outside edge

Ball point pen or pencil

Rough spots on inside edge

Do not touch the underside of the disc

Do not bend

Wipe the disc from center toward the outside edge

Label side up

Disc Cleaning

Use a dry soft cloth to wipe the surface. If the disc is quite dirty, use a soft cloth slightly moistured with isopropyl (rubbing) alcohol. Never use solvents such as benzine, thinner or conventional record cleaners as they may mar the surface of the disc.

Handling and Cleaning

Dirt, dust, scratches and warping disc will cause misoperation. Do not place stickers or make scratches on discs. Do not warp discs. A disc should always be kept in its case when not in use to prevent from damaging. Do

not place discs in the following

places:

1.Direct sunlight

2.Dirty, dusty and damp areas

3.Near car heaters

4.On the seats or dashboard

Discs which cannot be played with this player

Digital Video-RAM CDV CDG

Note:

A disc may become somewhat scratched (although not enough to make it

unusable) depending on your handle it and conditions in the usage environment.

Note these scratches are not an indication of any problem with the player.

Disc formats supported by this player

Digital Video

VCD

CD

MP3

Audio and Vide o Disc size 12 cm

Audio Disc size 12 cm

Digital Vide o

VCD

CD

MP3

NOTES:

Choose the mounting location where the unit will not interfere with the normal driving function of the driver.

Before finally installing the unit, connect the wiring temporarily and make sure it is all connected up properly and the unit and the

system work properly.

Use only the parts included with the unit to ensure proper installation. The use of unauthorized parts can cause malfunctions.

Consult with your nearest dealer if installation requires the drilling of holes or other modifications of

the vehicle.

Install the unit where it does not get in the driver s way and cannot injure the passenger if there is a sudden stop, like an emergency stop.

If installation angle exceeds 30 from horizontal, the unit might not give

its

optimum performance.

Avoid installing the unit where it would be subject to high temperature, such as from direct sunlight, or from hot air, from the heater, or where it would be subject to dust, dirt

or excessive vibration.

DIN FRONT/REAR-MOUNT

This unit can be properly installed either from "Front"(conventional DIN Front-mount) or "Rear"(DIN Rear-mount installation, utilizing threaded screw holes at the sides of the unit chassis). For details, refer to the following illustrated installation methods.

'

Installation

-5-

30

Installation

-6-

Installing the unit

If you want to take the CHASSIS out of the SLIDE BRACKET HOUSING, first remove the PLASTIC COVER on both sides , then insert the two KEY PLATES

into the left and the right sides of the chassis as illustrated above.

KEY PLATE

PLASTIC TRIM OUT

KEY PLATE

DASH BOARD

METAL MOUNTING STRAP

HEX NUT

SPRING WASHER

PLAIN WASHER

TAPPING SCREW

CONSOLE

SLIDE BRACKET HOUSING

HEX BOLT

SCREWDRIVER

TABS

Electric Connection

-7-

WIRING CONNECTION

Note:

the ground connection cable (parking brake B-) must be connected in order for pictures to be played back to the monitor. If the cable has not been correctly connected, the message “PARKING BRAKE” appears on the monitor.

(B+)12V REAR CAMERA SWITCH

(B-)PARKING BRAKE

GREY

GREY/BLACK

FRONT RCH SPK.

VIOLET

VIOLET/BLACK

WHITE

WHITE/BLACK

GREEN

GREEN/BLACK

REAR

LCH SPK.

AUTO ANTENNA

BLUE

GROUND(B-)

MEMORY BACK-UP(B+)

IGNITION SWITCH(B+)

RED

YELLOW

BLACK

REAR RCH SPK.

FRONT

LCH SPK.

LIGHT GREEN

FUSE

KEY GROUND(BLACK) KEY 1(BROWN) KEY 2(WHITE)

ISO CONNECTOR

VIOLET/WHITE

TV ANTENNA JACK

SUBWOOFER GREY

RCH RED

LCH WHITE

REAR OUTPUT CABLE

FRONT RCA WHITE L

FRONT RCA RED R

VIDEO OUT

YELLOW

FRONT RCA OUTPUT CABLE

REAR CAMERA INPUT YELLOW

RADIO ANTENNA JACK

RCH IN RED

LCH IN WHITE

VIDEO OUT(2) YELLOW

AUX 2 VIDEO IN YELLOW

AUX2

-8-

Remote Control

18. RPT BUTTON

19. ANG BUTTON

20. 10+ BUTTON

21. LANG/L/R/ST BUTTON

22. A-B/CLEAR BUTTON

23. >II BUTTON

24. >>I BUTTON

25. ZOOM BUTTON

26. EQ BUTTON

27. SUBT BUTTON

28. POWER BUTTON

29. APS BUTTON

30. MENU BUTTON

31. SETUP BUTTON

32.GOTO/SEARCH BUTTON

33. PBC/TITLE BUTTON

34. RDM BUTTON

35. /FINE - BUTTON

36. /FINE +

BUTTON

37. /CH + BUTTON

38. / CH - BUTTON

1. OSD BUTTON

2. PROG BUTTON

3. LOUD BUTTON

4. 9

5. LOCK BUTTON

6. ANGLE/MO/ST BUTTON

7. LOC/SLOW BUTTON

8. STOP BUTTON

9. I<< BUTTON

12. STEP BUTTON

13. SRC BUTTON

14. MUTE BUTTON

15. BAND BTTON

NUMBER(0~ )BUTTONS

C

10. SELECT BUTTON

11. VOLUME+/-

BUTTONS

16. OK BUTTON

17. INT BUTTON

3

19

12

21

23

22

20

4

5

7

6

8

26

27

29

31

32

34

33

38

35

30

28

12

14

15

18

17

16

13

37

36

11

25

24

9

10

-9-

Remote Control

Using the Remote Control

Face the remote control towards the player front face IR mark (remote control signal

receiver).

Operation angle: About 30 degree in each the direction of the front of the IR mark.

Preparing the Remote Control

1.First push to inside as the direction indicated by the arrow (See )And then

Remove the battery holder as the direction indicated by the arrow (See ).

2.Replace the battery Set a new battery property with (+)side up as illustrated

(See ).

3.Insert the battery holder. Push in the holder to the original position(See ).

1

2

3

4

Inserting the Battery

Note :

The lithium cell in the battery compartment of remote control has been secured for

transport with a plastic . Before initial use please remove this plastoc so that the

remote control is ready for operation .

Basic Operation

-10-

POWER ON/OFF

LOADING/EJECTING A DISC

Ejecting a Disc

In disc mode, Press the (2) button on the front panel to eject the disc .

Loading a Disc

3. The player starts playback the disc automatically .

2. Insert the disc with printed side facing up into the disc slot (1) .

1

2

1. Press the POWER ( ) button on the front panel to turn the device on .

Touch the “OFF” ICON on screen to turn the unit off . Press the“ ” onthe front panel to turn It on, press it again to turn off .

OPEN/CLOSE MONITOR AND ANGLE ADJUSTMENT

Press OPEN button on front panel, the monitor will draw out automatically .

OPEN/CLOSE button

FIG.1

When the monitor draws out to a certain location, it will turn upward automatically and stop at vertical position .

FIG.2

FIG.3

Do not rotate the monitor forcibly to avoid mechanical damage .

FIG.4

Return the monitor to the central viewing position, then press OPEN button on the front panel , the monitor will turn downward automatically .

FIG.5

Adjusting the viewing angle . When the monitor does not move, you long press button on the panel to turn the monitor upward or downward at fine steps to get a desired viewing angle ; short press that button ( ) on

remote is screen move back

or out.

Basic Operation

-11-

When the monitor turns downward to a certain angle, it will draw in .

FIG.6

Main Menu Operation

In many modes, touch the icon or In DVD/VCD mode , touch the range to enter the main menu, the message like following as below.

1. POWER icon In any modes, touch

the POWER icon to switch the unit off . The monitor will draw in automatically .

2. UP icon Touch this icon to adjust the angle of the monitor upward until your desired

angle .

3. CLOSE icon Touch this icon to Close the monitor .

4. DOWN icon Touch this icon to adjust the angle of monitor downward until your desired angle .

5. EJECT icon Touch to allow for inserting or ejecting disc.

6. SETUP icon Touch to enter the SETTING mode, the message will display as follow :

General setup interface2

GENERAL

WALLPAPER ...

TV

NTSC

ABOUT ...

ADJUSTABLE ITEMS:

ANIMATION

In RADIO mode, you can change the playing time of animation among of “OFF, 10S, 30S, 1M,90S, 2M, 3M and 4M ”.

Note:

Please set the playing time of the animation to “ 10S ” for the first, when you turn the unit on .

KEY BEEP : ON or OFF.

Tou c h the “ ” section on the setting menu, touch the “ / ” ranges to select the adjustment item, Touch the “ ” icon to return to

the

previous playback .

Setup interface 1

GENERAL

ANIMATION 2 MINUTE

KEY BEEP ON

DISC ...DISC ...

RADIO ...

General setup interface1

10:00 AM

(3)

(1)

(5) (6)(2) (4)

Setup interface 2

ILLUMINATION COLOR

-12-

Basic Operation

Disc setup as follow:

FORMAT

TV TYPE

This is to select the appropriate TV aspect (4:3 or 16:9) according to the connected TV set.

Normal/PS (For 4:3 TV)

Played back in the PAN & SCAN style. (If connected to wide-screen TV, the left and right edges are cut off.)

Normal/LB (For 4:3 TV)

Played

back in LETTER BOX style. (If connected to wide-screen TV, black bands appear at top and bottom of the screen.)

Wide (For 16:9 TV)

Select when a wide-screen TV set is connected.

RATING

Select to turn Parental Control on or off.

This player is capable of playing discs recorded in either PAL or

NTSC formats. Make the selection based on whether you are connecting the unit to a PAL TV or an NTSC TV. You can also set the unit to AUTO (auto select). The disadvantage to autoselect is that each time you turn the unit on it checks to see what kind of monitor is connected, which causes a

small delay and some flickering of the display image which you may find unpleasant.

The factory default password is 0000.

16:9

4:3 Letter Box

4:3 Pa n Scan

DISC

FORMAT NTSC

TV TYPE 4:3PS

RATING ADULT

changes to the Parental Control menu below .)

Key in “0000” and then turn to rating then you can setting as follow: KID SAFE -> G -> PG -> PG-13

-> PG R -> R ->NC-17 -> ADULT

RADIO

DUAL: touch to select stereo or mono.

LOCAL: touch to select

local or distant.

REGION: touch to select radio frequency as USA or EUROPE.

TV

Touch to select TV type as:NTSC, PAL, SECAM.

WALLPAPER

Tou c h to select wallpaper .

ABOUT

Tou c h to show the version information.

CLOCK SETUP

Tou c h the CLOCK to adjust the time and time format.

AUDIO SETUP

Tou c h the audio to turn to audio quality adjustment.

(The password must be used to make

clock setup interface

audio setup interface2audio setup interface1

-13-

Basic Operation

The RESET button is to be activated for the following reasons: A. Initial installation of the unit when all wiring is completed. B. All the function buttons do not operate. C. Error symbol on the display.

Rear Vie w Camera

When connecting the rear view camera the mirror image of the rear view is automatically displayed on the monitor when you change the gear to the back position. (Note: additional monitor can not display the image.)

Reset Factory Settings

RESET button is placed on the housing and must be activated with either a ballpoint pen or thin metal object.

RESET

TREBLE: -7 to +7 Adjust treble level .

BASS: -7 to +7 Adjust bass level .

SUBWOOFER: touch to adjust subwoofer volume and frequency.

EQ: touch to select audio mode as follow:

USER -> JAZZ -> CLASSIC -> POP -> ROCK

LOUDNESS: touch to select loudness effect as :OFF -> LOW -> MID -> HIGH

FADER/BALANCE: BALANCE: R 0-10 to L 0-10

Adjust sound balance between left and right speakers .

FA DE: F 0-10 to R 0-10 Adjust sound balance between front and rear speakers .

VIDEO SETUP

COLOR: 0 to 32

Adjust the color for

the picture-lighter

or darker.

BRIGHTNESS: 0 to 32

Adjust if the picture is too bright or too dark.

CONTRAST: 0 to 32

Adjust the contrast of the bright and dark portion.

TINT: 0 to 32

Adjust the tint if the human skin color is unnatural.

-Adjustable when “NTSC “ is selected for “NTSC/PAL

“ .

LANGUAGE

Touch to select OSD language.

ILLUMINATION COLOR

Tou c h to select the backlight for all buttons. Tap auto icon the backlight change automatically.

CALIBRATION

Tou c h the arrow as show to calibration the display.

Video setup interface

-14-

UNIT KEYS

Control Panel

5817 9 10 1211 134

3

6

7

16

15

14

1

2

19 18

1. OPEN/ BUTTON

To slide the monitor out and stand it up or into the monitor slot, press this button; To adjust the angle of the monitor, press the 5/ or 6/ to change the angle for

the TFT display.

2. SEL BUTTON and VOL KNOB

In normal mode, the VOL knob is used to increase or decrease the volume.

Press the SEL(except radio mode) to switch between BASS,TREBLE,

BALANCE, FADE,COLOR,RIGHTNESS, CONTRAST, TINT , LOUD, SWF, EQ, TIME 12H/24H, CLOCK, BEEP,EUR/USA FREQ, ANIMATION, TV SYSTEM.

After switching on the desired mode above, rotate VOL knob or press VOL+/ VOL- buttons to set it.

Control Panel

-15-

3. (POWER On/Off )/MODE

Press it to turn on the unit, to switch the device off. In playback mode, Press it repeatedly to select RADIO, DISC, USB, CARD, TV, AUX and AV mode.

4

long pressing |<< or >>| button can automatically search down or up for an available station beginning from the current frequency; Briefly pressing |<< or >>| button can manually search down or up for a your desired station beginning from the

current frequency.

In media mode, pressing |<< or >>| button can play the previous or next track; continuously and long pressing |<< or >>| button can fast backwards or forwards at the following multiple of normal speed: x2, x4, x8, x20.

6. MUTE BUTTON

Press it button to switch of the loudspeakers for a short period. The word MUTE flashes in the display. Press it again to cancel the mute function. This function can also be cancelled by rotating the VOL multifunction button.

-13. PRESET STATION MEMORY AND >II, INT, RPT, RDM BUTTON

A)In RADIO mode

Go to any preset station by pressing one of the 6preset station(1-6) ,if one of these buttons is pressed for more than 2 seconds, the stations currently being listened to will be memorized into the selected preset button.

B) In DISC/USB/SD mode During playing, press 1/>II button to pause the current playback, press again to to continue play;

During playing, press 2/RPT button to select repeat function;

During playing, press 3/RDM button to select random function;

During DVD/VCD/CD disc playing, press 4/STOP button to stop playing and turn to home mode, during MP3/USB/SD mode, press this button to turn to previous mode, press again to turn to home mode;

4

Press and hold for two seconds

/5. >>| and |<< BUTTONS

In radio mode,

7. USB PORT For information about connecting a USB device, please see USB operation.

8

1. AUXILIARY INPUT JACK

Insert an external device to this AUX jack in order to have audio output of the device through the unit

In radio mode, press the SEL to select MANUAL/AUTO mode, in radio manual

mode to scan the frequency by rotate the VOL knob, select radio auto mode to

cancel the scan function.

Control Panel

-16-

16. REL BUTTON

Press it to detachable the front panel.

7

15. (EJECT) BUTTON

Insert the disc, label side facing up, until the mechanism senses its presence

and draws the disc in. Press it to eject the disc..

1. LCD Display window

18. SD CARD SLOT

19. RESET BUTTON

Press this button to return to factory settings.

Touch Screen Operation

-17-

Selecting The Frequency Band

Touch the screen of “ BAND ” section repeatedly to select the band , the message will show in turn :

When an FM stereo broadcast is hard to receive

Press ST/MO button on the remote control to select the MONO or STEREO mode .

FM1 FM2 FM3

AM2(MW2)

AM1(MW1)

RADIO OPERATION

Touch the RADIO ICON in home menu to enter the RADIO mode:

Briefly touch “ ” to decrease frequency by one step of channel spacing.

Automatic Search

During Radio mode, touch and hold (for more than 2 seconds ) either “ /

” ICONS to start search for a radio station automatically.

To tune in strong-signal FM Station only (LO/DX function)

Press button on the

remote control to select

mode of Local and

Long-distance traffic news.

Storing and Listening to a Memory Station

Setting Memory

With this system, a total of 30 stations can be stored in the memory of six buttons. Each band stores up to six preset stations. The stations might be FM1, FM2, FM3, AM1(MW1), and AM2(MW2) band.

The operation is as below :

In radio mode, LOC

or tap icon

select LOC/DX

Listening to Radio

10:00 AM

Start Searching For a Station

Manual Search

During Radio mode, briefly touch “ ” to increase frequency by one step of channel spacing.

10:00 AM

FM1 87.50 MHz 4

87.50 90.10 98.10

107.9 100.8

87.50

10:00 AM

-18-

Touch Screen Operation

Automatic Memory Storing & Program Scanning

3

Automatic Preset Setup

In Radio Mode, touch and keep (for more than 2 ’ S) the screen of “ ” range to active automatic station storage. The radio searches within the current frequency band, e.g. Fm , for the stronger signal level until the search cycle has finished . The six strongest

stations are then allocated to the corresponding storage locations . Then the station of the first storage location is set .

Scan Function

In Radio mode, briefly touch the “ ” section on the touch screen , the radio briefly plays all the preset stations of the frequency band .

- Store in Memory >Select the frequency band

> Select the station >Press and the station until it show

the frequency band your select.

- Retrieve a preset station Touch the 1-6 ranges briefly to retrieve

a station which had been stored in the memory

in advance the chose number

is shown on display .

-19-

Touch Screen Operation

Media Operation

In audio play mode, the message will display as below : (When Parking Brake is applied .)

The icons for other mode

(The same icon have the same function in each mode)

In PHOTO playing ,tap to change the photo direction.

ZOOM IN and OUT.

For page turning.

Mute function

To select the Equalizer mode

Fast forward

Fast backward

Intro Function

To decrease the volume level

To increase the volume level

Loudness Function

Subwoofer Function

Play/Pause the playing

To skip the next track

To skip the previous track

Repeat Function

Random Function

Previous menu

10:00 AM

Touch Screen Operation

-20-

FOR Digital Video :

Tap the icon or press the RPT button on the remote control to select REPEAT mode as follows :

REPEAT ALL

CHAPTER REPEAT ON TI TLE REPEAT ON

REPEAT OFF

Note:

when the JPEG disc playback, in normal mode, you can use the cursor buttons to rotate the picture . Press UP to invert an image . Press DOWN to mirror an image . Press LEFT to rotate an image to left . Press RIGHT to rotate an image to right .

FOR

VCD/CD :

Tap the icon or press the RPT button on the remote control to select REPEAT mode as follows :

FOR MP3 :

Tap the icon or press the RPT button on the remote control) to select REPEAT mode as follows :

FOR

CD :

Tap the icon or press the INT button on the remote control to play the previous 10 seconds part of each track/chapter on disc. (Touch it again to cancel this mode)

REPEAT OFF

REPEAT ONE REPEAT ALL

REPEAT ALL

REPEAT ONE REPEAT FO LD ER(or DIR)

REPEAT OFF

SELECTING PLAY MODES

During the Disc playback, select the “RPT, RDM, INT ” to select your favour play mode.

1). REPEAT FUNCTION

2). INTRO FUNCTION

Note :

For some VCD2.0 disc (PBC-playback control), above these buttons may be unavailable .

Skipping Track

During DISC playback, Touc h the / section on the touch screen to skip to next/back one track.

Digital Video/VCD/CD/MP3:

Normal Playback 2x 4x 8x 20x

Rapid Forward/Rapid Reverse

During DISC playback, touch the screen of “ / ” range the speed of rapid forward/reverse changes according to the disc as follow:

Use the direction keys ( / / / on remote control to move the enlarged picture .

Zoom Function

Touch the button repeatedly, the displayshow as “

zoom 2, zoom 3, zoom 4 , zoom ½, zoom 1/3, zoom 1/4 , zoom off

. ”

Stopping Play

Touch the screen the range to stop the unit playback. touch the range to start play.

Pause (still picture)

Touch the “ ” section on touch screen during playback will stop play temporary, touch it again to return the normal playback .

BASIC OPERATION

Touch Screen Operation

-21-

Note: when select the INTRO Mode, this player to start to play the previous 15 seconds part of each track/chapter on disc. (Touch it again to cancel this mode .)

3). RDM(RANDOM) FUNCTION

During DISC playback, touch screen of “ ” section ( press the RDM button on the remote control to play in random. Each play mode the order is different . (Depend on the disc used for VCD). Touch it again to cancel this function .

FOR VCD :

Press the INT button on the remote control. It display will following menu as below :

FOR Digital Video/MP3 :

For Digital Video/MP3 , press the INT button is not available .

SEQ PLAY INTR O 1

OSD

2. Example for VCD/SVCD, when it is on, it will display the information such as:

3. Example for Movie or PHOTO . When it is on, it will display the information such as:

DISC Search (GOTO)

FOR Digital Video :

Tou c h the screen as show or press the GOTO button on remote control;

the screen will display the following message :

Touch the to select the your adjustment item, then select the item your favour by touching the numberic buttons , then touch

the OK button

to confirm .

T 001/004

C 001 /00 1

Note : in random mode, the button

is not available .

During playback, touch the screen or press the OSD on the remote control, it will display

the following as below :

Note: touch the screen or press the OSD on the remote control again to cancel the OSD information.

1. Digital Video , when it is on, it will display the information such as:

ON-SCREEN DISPLAY FUNCTION

-22-

Touch Screen Operation

the screen will display the following message :

Touch the to select the your adjustment item, then select the item your favour by touching the numberic buttons , then touch the OK button to confirm .

For Movie/Photo:

Touch the screen as show or press the GOTO

button on remote control;

the screen will display the following message :

Touch the to select the your adjustment item, then select the item your favour by touching the numberic buttons , then touch the OK button to confirm .

FOR VCD (With PBC OFF) :

Touch the screen as show or press the GOTO button on remote control;

-23-

Digital Video Special Function

Touch Screen Operation

4. Tit le Menu Function

For Digital Video :

If the Digital Video has multiple titles recorded on the disc. It can select preferred title from the title menu to start playback.

- During Digital Vid eo playback, press TITLE button on the remote .The title menu is display.

- Select preferred title by the

cursor button and confirmed by press the ENTER button .

For VCD:

Press TITLE/PBC button on the remote control while the disc is playing, you can switch between "PBC ON"and "PBC off" mode.

MONO LEFT MONO RIGHT

STEREO

MIX-MONO

For VCD/CD:

during playback, touch the AUDIO section of the touch screen or Press AUDIO on the remote . It is possible to switch the sound between monaural and stereo sound.

2. Multi-Audio Language Function

For Digital Video:

During Digital Video playback , touch the icon on touch screen (or press the LANG

on the remote .) Each time the button is pressed or touch , number of the audio soundtrack language changes on sequential order.

Notes:

- The language number

is different

according to the disc.

- Some disc only contain one language soundtrack

- When no different language soundtra ck are recorded will be display at screen left top corner.

“ INVALID KEY ”

Notes:

- The language number is different according to the disc.

- Some discs only contain one subtitle language.

- When no different subtitle language are recorded, “ INVALID KEY ” will be displayed at screen left top corner.

During Digital

Video playback. Touch the icon on touch screen(or press the SUBT on the remote) .

1. Multi-subtitle Language Function (for Digital Vi de o Only)

Each time the button is pressed or touch, number of the subtitle language changes in sequential order.

During Digital Video playback, touch the icon on the touch screen . Each time the button is pressed , the number of the angel changes in sequential order .

Notes:

- The angle number is different according to the disc.

- The function only work for disc having scenes recorded at different angles.

- When no different angle are recorded, will be displayed at

screen left top corner.

“ INVALID KEY ”

3. Multi-Angle Function (for Digital Video Only)

Touch Screen Operation

-24-

5. A-B Repeat (for Digital Video and VCD)

Press the A-B button if you want to repeat a specific segment on a disc that you define:

1. Press the A-B button at a point (A) where you want it to be the start point of the repeat segment. Press the A-B button again at a

point (B) where you want it to be the terminal point of the repeat segment. Then it will play the segment repeatedly.

2. To cancel the A-B repeat mode and resume normal playback, press the A-B button for the third time.

Note:

During DVD playback, points A and B can be selected from different chapters.

6. Program Playback (for Digital Vi de o and VCD)

It allows you to enter the order in which you want some chapters/tracks in DVD/VCD to play. 1 During playback, press the PROG button to enter a program interface as follows:

2 Use the direction buttons to move cursor onto the desired place for inputting the sequence number.

3 Use the number button to input desired sequence number of title/ chapter/track with desired sequence.

4 After input your favour, press >II on remote or use the direction buttons to select

play and then press OK on remote to play the programmed titles/ chapters/tracks in programmed order.

* Ta p the display or press stop button to exit the PROG .

* During VCD playback, if it is in PBC ON mode, at the same time of entering the state of

program playback, it turns

off PBC mode.

7.

Display still frame step by step

(for Digital Vi de o and VCD)

If the unit is currently playing video, press the STEP button consecutively to display still frame step by step.

Press the PLAY button to resume normal playback.

8.Playback with Slow Speed

During video playback , press the LOC/SLOW button to execute the Slow Forward function.

Press the PLAY button to resume normal playback.

PROGRAM

Program interface for DVD

Touch Screen Operation

-25-

TV operation

1. To enter TV mode (SOURCE button or TV icon) When you use SOURCE button or source menu(tapping TV icon) to enter TV mode, first it displays TV interface, and broadcastes program after a while.

During TV broadcasting, touching any place on touch screen

can pop up TV interface as

follows:

2. To search and save TV channels(SCAN icon or SEARCH button) Touching icon or pressing SEARCH button can search for all available channels from the lowest frequency to highest frequency. After searching

for a circle, it will stop searching and broadcast the available channel with the lowest frequency and all the available channels from the lowest frequency to the highest frequency will be saved.

3. To select a desired channel with an available station (

and icon or CH- and CH+ or |<< and >>| buttons) After searching, touching or icon or pressing CH- or CH+ button on remote control or pressing |<< or >>| button on control panel can select the channels

with available stations.

4. To select a desired channel (0~9) Use the 0~9 icons or the 0~9 buttons to directly select the channel.

* the +10 button is not available.

5. To fine tune the current channel(FINE- and FINE+) Touching FINE- or FINE+

icon or pressing FINE- or FINE+ button to fine fune for better signal.

6. To add or delete a channel(SKIP button or OK icon) After searching channels automatically, the CH+/CH- buttons on remote control and >>|/|<< buttons on control panel and /

icons can select only the channels with available signal.

1) Add Channels Use the number buttons to select a channel, then press SKIP button or touch OK icon, the screen will display SAVE, the channel will be available for the CH+/CH- & >>|/|<< buttons

and

/ icons.

2) Skip Available Channels Use the CH+/CH- or >>| / |<< buttons or / icons to select a channel you want to skip for the CH+/CH- & >>|/|<< buttons

and / icons, then press SKIP button or touch OK icon, the screen will display SKIP, the channel will be skipped for the CH+/CH- & >>| / |<< buttons and / icons.

icon = SW button

icon = LOUD button

icon = MUTE button

and

icons = VOL- and VOL+ buttons = VOL knob icon = EQ button

icon: To enter source menu.

-26-

Touch Screen Operation

AUX Operation

On the front panel of this unit, there is an AUX IN jack, follow the diagram below to connect analogue replay devices(only for the Audio connect, if you want to connect the Video, please plug the RCA <Video input > on the back of the unit .) . Use this jack to

replay sound of other replay equipment such as Digital Video players, computers, etc. Via the loudspeakers.

1). Please connect the external device with stereo jack (3.5mm)plug the Aux in socket .

AUX IN JACK FRONT PAN EL

AUX IN

Ground

Right

Left

AUX IN

2). In radio mode, touch the screen of “ ” ICON to enter the main menu, touch the “ AUX ” ICON to enter the AUX IN mode .

10:00 AM

AUX INTERFACE 1

10:00AM

AUX INTERFACE 2

10:00AM

3). You now hear the sound from the external device played back through the loudspeakers .

The function of the icons as follow:

Tap to mute the sound.

Tap to select EQ as the same on the

remote control.

Tap to turn LOUD on or off.

Tap to select subwoofer frequency.

Ta p to adjust audio volume.

Touch Screen Operation

-27-

AV Operation

Please plug the RCA <Video input > on the back of the unit .

Touch the AV IN icon to enter the AV IN mode.

As the interface show, here is only the audio output, now tap the icon, the picture of the auxiliary input video show on the display and tap the display again to turn to audio mode.

Now you can watch the video from your External video equipment such as

Digital

Video players, computers, etc.

The function of the icons as follow:

Tap to mute the sound.

Tap to select EQ as the same on the remote control.

Tap to turn LOUD on

or off.

Tap to select subwoofer frequency.

Ta p to adjust audio volume.

Note: To ensure safety while driving and to comply with lows, drivers should not watch video or operate the video device while driving.

AV INTERFACE 1

10:00AM

10:00 AM

AV INTERFACE 2

10:00AM

-28-

Following the diagram below, connect your USB device to the front panel USB port . If it is properly connected, the device will be mounted and start playing automatically.

USB OPERATION

Touch Screen Operation

1 Current type (highlighted bar) .

2 Audio play mode select.

3 Picture play mode select.

4 Movie play mode select,

5 Current play track .

1 Current type (highlighted bar) .

2 Audio play

mode select.

3 Picture play mode select.

4 Movie play mode select,

5 Current play track .

Card OPERATION

The unit can support playback MP3/WMA/ JPEG/MP4 and Divx format which are stored on SD memory cards . Please read the following instructions before you start using a memory card . Inserting the card as follow:

Press REL button to detachable the panel

Label side facing upward

1

SONG

001

002002

003

004

005

10:00AM

2 3 4

5

1

WEDDING MOV03247.MPG

CIMG3080.MOV

10:00AM

2 3 4

5

10:00 AM

Touch Screen Operation

STEERING WHEEL CONTROL

Touch the SWC icon as follow to turn to steering wheel control .

During setting, touch the icon to turn to home menu.

There are 2 KEY for total 12 buttons to save, first, tap Assign to open function save, then select button 1 in KEY 1 on steering

wheel and tap the icon, the icon show in button 1 position then touch Confirm, final turn the unit on again, the function will save in button 1 of KEY 1.

The function of the icons as follow:

Touch to begin function save.

After selection touch to confirm operation.

Touch this icon to cancel the input and resume load.

When electric resistance is too low, touch this icon to increase.

When electric resistance is too high, touch this icon to reduce.

-29-

10:00 AM

Parental Control

-30-

* Parental Control

Q: After inserting a Digital Vi deo disc into the disc slot, ?

A: The playing disc is locked by a rating level of parental control. If the current rating level of parental control of the Digital Vi deo

player is lower than the one of current disc, you must input the correct password of parental control to unlock the parental control and enter a rating level one

* For factory preset password of parental control of Digital

Vi deo player,

part of Media Setup Menu

Appendix: Parental Control

Parental Control function of a Digital Video player can control playback of movie ratings on a disc. You can set the Digital Video player to be a certain rating level of parental control using the Media Setup Menu. If the rating level of parental control of a disc is higher than the one of the Digital Video player, the Digital Vi deo player cannot play the disc.

The Digital Vi deo movie can be designed so that the Digital Video player can play different versions of content of a particular movie according to the different rating levels of parental control. Depending on igital Vi deo , the scenes

that are not suitable for children will be cleared or replaced by suitable

scenes automatically.

The rating levels of Parental Control are as follows:

Unlock 1 Kid Safe

2 G 3 PG 4 PG 13 5 PG R 6 R 7 NC 17

8 Adult

if a dialogue box pops up

and asks you to input a password, what should you do

equal to or higher than

of the current disc in order to play the disc.

the D features

please

see the .

Region Code for DVD

-31-

* Region Code

Appendix: Region code of D

Motion Picture Association of America (MPAA) divided the world into 6 regions, and gave every region a region code for locking and unlocking D playback.

Please

Region codes and the countries or areas represented by region codes are as follows:

Region 1: America, Canada, East-Pacific Inlands; Region 2: Japan, We st Europe, North Europe, Egypt, South Africa, Middle East;

Region 3: Taiwan, Hong Kong, South Korea, Thailand, indonesia, etc.; Region 4: Australia, New Zealand, Central South America, South Pacific Inlands; Region 5: Russia, Mongolia, Indian Peninsula, Middle Asia, East Europe, North Korea, North Africa, North-west Asia etc.; Region 6: China mainland.

If you insert a disc into the disc slot and REGION ERROR is displayed, the car multi-media system can not play the disc. The reason is that the region codes of the car multi-media system and the used disc do not match each other.

igital Video

as the code of the igital Video

igital Video igital Video

impose this restriction. igital

Video igital Video -

has motivated the

igital Video igital Video

-

Basically, a coded D player can play only the discs if its region code is the

same D player. Otherwise, it cannot play the disc.

note that only the D discs and D players produced by

the 8 biggest film-making companies of America The D

discs and D players not

produced by the 8 biggest film making companies of America are not restricted by the rule of region code. Generally, they are called Free Region Code or Full Region Code.

The problems caused by area code inconsistency production of unlocked version D players and recodable

D players .

South-east Asian countries include

The 8 biggest film making companies of America are as follows:

1. WarnerBros;

2. Columbia;

3. 20thCenturyFOX;

4. Paramount;

5. Universal;

6. UA(UnitedArtist);

7. MGM(MetroDogwynMayer);

8. WaltDisney

Specification

-32-

TFT Monitor:

Monitor Screen Size: 7 Inch Wide Color System: NTSC/PAL

NOTE:

Specifications and design are subject to modification, without notice, due to improvements in technology.

RADIO Section:

For 2 Bands For

2 Bands

(Europe) (U.S.A.)

FM FM

Frequency Coverage: 87.5 to108 Mhz

87.5 to107.9 Mhz

IF: 10.7 MHz

10.7 MHz

Sensitivity (S/N = 30 dB): 15 dBu 15 dBu

MW AM

Frequency Coverage: 522 to1620 KHz

530 to1710 KHz

IF: 450 KHz

450 KHz

Sensitivity (S/N = 20 dB): 40 dBu 40 dBu

Audio Signal Output: 2ch&4ch line out Characteristics: (1)Frequency Response 20 Hz - 20 KHz

(2)S/N Ratio 90 dB (JIS)

(3)Wow and Flutter Below measurable limits

General :

Supply Voltage: 12V DC (11V-15V) Current Consumption: Less than10 A Signal System: Compositive video 1.0Vp-p 75 Discs Played:

(1)DIGITAL-VIDEO Disc

5"( 12 cm) single-sided, single-layer

5"(12 cm) single-sided, double-layer

(2)Compact Disc (CD-DA, VIDEO CD)

5"(12cm) disc

TV

TV System NTSC/PAL/SECAM TV Sensitivity 45dB

uV@CH25 in average

-33-

Before going through the check list, check wiring connection. If any of the problems persist after check list has been made, consult your nearest service dealer.

Troubleshooting

Inserting the disc in reverse direction

Press the RESET button. Front panel is not properly fixed into its place

The car ignition switch is not on

If the power supply is properly connected to the car accessory terminal,switch the ignition key to "ACC"

The fuse is blown

Replace the fuse

Presence of disc inside the player.

Remove the

disc in the player,

then put a new one

Insert the compact disc with the label facing upward

The disc is extremely dirty or defective

Clean the disc or try to play a new one

Temperature inside the car is too high

Cool off or until the ambient temperature return to normal

The built-in microcomputer is

not operating properly

due to noise The antenna cable is not

connected

Insert the antenna cable firmly

The signals are too weak

Select a station manually

SYMPTOM CAUSE SOLUTION

Video/image appears black-white

The color system is set incorrectly

Please switch to correct color system from menu

No video/image appears

The unit is not connected to the parking brake detection switch

Make proper connection according to wire connection

“”

The parking brake is not engaged

For safety reasons no video/ images are displayed while the vehicle is moving. Engaging the parking brake will cause images to be displayed.

The operation keys do not work

The radio does not work

Disc can not be loaded or ejected

No power

No color in picture

The disc format is not according to the TV-set used (PAL/NTSC)

Please choose a proper color system.

JPEG disc can not be played back

No JPEG files are recorded on the disc.

JPEG files are not recorded in a compliant format

Change the disc Record JPEG files using a compliant application

Change the disc

Made in China 88-J9967-02