BV9958B
AM/FM DVD Receiver with 7” TFT Display
U S E R ’ S M A N U A L
CONTENTS
Installation
To support the unit
Detaching and attaching the front panel
Moving the screen forward
Cleaning the connector
Wire Connection
Location of parts and controls (Main unit and Remote control)
General operations
Listening to radio
Using the RDS function
Operations common for audio/video
Listening to MP3/WMA
Playing DVD/video CD/MP4
How to use bluetooth in your car audio
Customizing audio/video settings
Setting up the DVD player
Troubleshooting
Specifications
2
3
3
4
4
4
6
7
8
9
9
10
11
12
13
14
15
16
2
Before installing your new DVD Receiver, please review the items
below carefully.
Use only the installation parts and hardware provided with the unit to ensure
proper installation. Using other parts can cause malfunction and possible damage
to your DVD receiver.
affect performance.
3
10
7
1
2
3
4
4
4
5
5
6
6
8
9
INSTALLATION
PRECAUTIONS
• Choose the mounting location carefully so that the unit will not interfere with the normal driving
functions of the driver.
• Avoid installing the unit where it would be subject to high temperatures, such as from direct sunlight
or hot air from the heater, or where it would be subject to dust, dirt or excessive vibration.
• Use only the supplied mounting hardware for a safe and secure installation.
• Be sure to remove the front panel before installing the unit.
NOTE:Inclination angle for car radio installation must not exceed 30° otherwise the front panel will not open.
NOTE: Keep the release key in the safe place as you may need it in future to remove the unit from the car.
TO SUPPORT THE UNIT
Detaching and attaching the front panel
The front panel of this unit can be detached in order to prevent the unit from being stolen.
Before detaching the front panel, be sure to press the button (1) OFF first.
Then press the button and detach the panel by pulling it towards you as illustrated.
Notes:
• Do not press the front panel hard against the unit when attaching it. It can be easily attached by
pressing it lightly against the unit.
• When you carry the front panel with you, put it in the supplied front panel case.
• Do not press hard or give excessive pressure to the display window of the front panel when attaching
it to the unit.
Detaching and attaching the display screen
• When the lower part of the front panel (control board) is detached, the unit can be power off.
• Do not press hard or give excessive pressure to the display window of the front panel when attaching
it to the unit.
• Pay attention not to put any pressure on the display or control buttons.
1
B
A
C
2
182mm
53mm
3
4 5
Bend these
claws, if necessay
Release screw and
bracket
1. UNIT
2. RELEASE CASE
3. DASH BOARD
4. HEX NUT
5. LOCK WASHER
6. PLAIN WASHER
7. CAR BODY
8. REAR SUPPORT STRAP
9. TAPPING SCREW
10. M5 X 15 HEX BOLT
Dashboard
4
Notes :
• Do not press the front panel hard against the unit when attaching it. It can be
easily attached by pressing it lightly against the unit.
• When you carry the front panel with you, put it in the supplied front panel
case.
Moving the screen forward
Depending on vehicles’s dashboard design, there might be instances where the
display screen might collide or bump into the dashboard’s control knobs.
Follow the steps below to move the screen forward.
1. Slide the switch to UNLOCK position.
2. Hold it in UNLOCK position then move the screen forward. The unlock switch
will move to LOCK position automatically when in place.
Cleaning the connector
The unit may not function properly if the connectors
between the unit and the front panel are contaminated
with dirt. In order to prevent this from happening,
detach the front panel by pressing the button and
clean the connector from time to time.
Clean the connector with a cotton swab together with
contact cleaner as illustrated. Be sure to clean them
carefully pin by pin and make sure not to damage the
connecting points.
WIRE CONNECTION
IN / OUT CONNECTOR
DVD Audio Out: White (L) Red (R)
Connect this wire to rear seat A/V monitor system to enjoy
DVD movie
Audio Out (Front): White (L) Red (R)
Audio Out (Rear): White (L) Red (R)
Video Out: Yellow
Connect to external A/V system to display
Video In: Yellow
Connect to external Video equipment
Rear Camera In: Blue
Connect to rear camera output
RCA Audio Input (Black):
Left (White) Right (Red)
Subwoofer Output (Green): Plug (Yellow)
External Bluetooth Microphone
CONTROL WIRE
Parking (Gray) : Connect this wire to car hand brake system
Auto Antenna/Remote Control (Blue) :
Rear Camera (Red) : Connect to back rear camera
During back gear condition, this wire should be connected to hight voltage.
LOCK
UNLOCK
Cotton Swab
Rear of
front panel
Main unit
To detach
1. Slide the screen release button
to the right side.
2. Hold the display by the trim
(not screen). Gently lift the
display right and upwards.
To attach
Push and insert the screen all
the way down until you heard 2
click sounds indicating both hole
connector is attached properly.
GRAY
PARKING
SUBWOOFERAUDIO IN
BLUE
AUTO
ANTENNA
RED
GREEN
BLACK
WHITERED
YELLOW
BACK GEAR
CONTROL
LINE OUT
LINE OUT
AUDIO OUT
ANTENNA
CONNECTOR
FRONT
REAR
CAMERA IN
VIDEO IN
VIDEO OUT 1
VIDEO OUT 2
FUSE 10A
L
R
L
R
L R
ISO CONNECTOR
B
A
1234567
8
478
BLUETOOTH
EXTERNAL MICROPHONE
BLUETOOTH ANTENNA
5
ANTENNA
CONNECTOR
FRONT
REAR
AUDIO OUT
CAMERA IN
VIDEO IN
VIDEO OUT 1
VIDEO OUT 2
R
L
L R
L R
ISO CONNECTOR
B
A
1234567
8
4
5 7
8
REAR
UT
CAMERA IN
VIDEO IN
R
L
L R
RED
OPEN
FRONT
SIDE
TOP VIEW
To rear camera video out
To reverse gear control switch
Steps:
1. Connect the Rear Camera IN plug to the rear camera’s video out plug.
2. Connect the RED wire to “REVERSE” gear control switch.
3. Check your gear control switch and make sure it is connected to +12V.
GRAY
BLUE
RED
OPEN
FRONT
SIDE
TOP VIEW
To Hand brake switch
Steps:
1. Connect the gray wire to the hand brake system.
2. Check your hand brake switch and make sure it is connected to car body chassis
and properly grounded.
ISO CONNECTOR A
4. MEMORY +12V
7. +12V (TO IGNITION KEY)
8. GROUND
NOTE: (connector A no. 7) must be connected by car ignition key in order to avoid that car battery
becomes weak when the car will be not used for long period.
CONNECTOR B
1. REAR RIGHT SPEAKER (+)
2. REAR RIGHT SPEAKER (-)
3. FRONT RIGHT SPEAKER (+)
4. FRONT RIGHT SPEAKER (-)
5. FRONT LEFT SPEAKER (+)
6. FRONT LEFT SPEAKER (-)
7. REAR LEFT SPEAKER (+)
8. REAR LEFT SPEAKER (-)
Maintenance
FUSE REPLACEMENT
If the fuse blows, check the power connection and replace the fuse. If the fuse blows again after the
replacement, there may be an internal malfunction. In this case, consult your nearest repairing center.
Warning
Use the specified amperage fuse for each lead. Use of a higher amperage fuse may cause serious damage
DRIVING WITHOUT VIDEO DISPLAY
Follow the installation below so when the car is in motion, no video will come out from the LCD screen.
Only sound can be heard from speaker.
Note:
- Only sound can be heard when car is in motion.
- Refer and follow your country’s law regarding driving with video.
Caution:
- Do not attempt to install it by yourself if the instruction is not clear to you. Consult you dealer concerning the installation procedures.
INSTALLING REAR CAMERA FOR PARKING OR REVERSE MOTION
You can install a separate camera at the rear of the car so when doing parking or reverse motion, the
unit will automatically switch the video to the rear camera to guide the driver.
Loading...