Boss Audio Systems BV9700 User Manual

2

FEATURES

Compatible with PAL DVD (Video
CD) and NTSC DVD (Video CD)

This player can play discs recorded in
either PAL or NTSC format.

• A single LSI chip now integrates all
major DVD playback circuit functions
including MPEG2 decoder, video D/A
converter, and audio decoders.

• L/R stereo analog audio outputs for
connection to existing head unit aux
inputs. Video output is composite
video.

• Supplied remote handles
multi-function software (multi-language
audio-track/subtitle, multi-angle, multi­story, etc.), plus all basic functions.

USE THIS PRODUCT SAFELY

This set has been designed and
manufactured to assure personal safety.
Improper use can result in electric shock
or fire hazard. The safeguards
incorporated in this unit protect you if
you observe the following procedures for
installation, use and servicing. This unit
doesn’t contain any parts that can be
repaired by the user.

When Driving

Keep the volume level low enough to be
aware of road and traffic conditions.

When Washing Your Car

Do not expose the product to water or
excessive moisture. This could cause
electrical shorts, fire or other damage.

When Parked

Parking in direct sunlight can produce
very high temperatures inside your
vehicle. Give the interior a chance to
cool down before starting playback.

Use the Proper Power Supply

This product is designed to operate with
a 12 volt DC, negative ground battery
system (the regular system in a North
American car).

Protect the Disc Mechanism

Avoid inserting any foreign objects into
the slot of this player.
Failure to observe this may cause
malfunction due to the precise
mechanism of this unit.

Use Authorized Service Centers

Do not attempt to disassemble or adjust
this precision product. Please refer to
the Service Center list included with this
product for service assistance.

For Installation

The unit should be installed in a
horizontal position with the front end up
at a convenient angle, but not more than
30˚.

Protect the Monitor Mechanism

• The monitor is operated automatically.
Do not pull the monitor out or turn it
upward or downward manually.
Otherwise, the mechanism
construction may be harmed to some
degree.

3

CONTENTS

Safety Information......................................................................................................4

Disc Notes...................................................................................................................5

Installation...................................................................................................................6

The Player ...................................................................................................................9

Electrical Connections.............................................................................................11

Remote Control ........................................................................................................12

Location and Function of Keys.............................................................................12

Preparing the Remote Control..............................................................................15

Loading/Ejecting a disc ...........................................................................................15

Loading a Disc......................................................................................................15

Ejecting a Disc ......................................................................................................15

Operation ..................................................................................................................16

Basic Operation ....................................................................................................16

Disc (DVD, VCD, CD, MP3) Operation..................................................................20

Radio Operation....................................................................................................26

TV Operation.........................................................................................................27

AV Operation.........................................................................................................27

RGB Operation .....................................................................................................27

Setup..........................................................................................................................28

Language Setup ...................................................................................................28

Display Setup........................................................................................................28

Audio Setup ..........................................................................................................29

Lock Setup ...........................................................................................................29

Other Table ...........................................................................................................30

Trouble Shooting ......................................................................................................31

Specification .............................................................................................................32

4

CAUTION:

MOBILE DVD PLAYER IS A CLASS I
LASER PRODUCT. HOWEVER THIS
MOBILE DVD PLAYER USES A
VISIBLE/INVISIBLE LASER BEAM
WHICH COULD CAUSE HAZARDOUS
RADIATION EXPOSURE IF DIRECTED.
BE SURE TO OPERATE THE MOBILE
DVD PLAYER CORRECTLY AS
INSTRUCTED.
USE OF CONTROLS OR
ADJUSTMENTS OR PERFORMANCE
OF PROCEDURES OTHER THAN
THOSE SPECIFIED HEREIN MAY
RESULT IN HAZARDOUS RADIATION
EXPOSURE.
DO NOT OPEN COVERS AND - DO NOT
REPAIR YOURSELF. REFER SERVICING
TO QUALIFIED PERSONNEL.

WARNING:

• TO REDUCE THE RISK OF FIRE OR
ELECTRIC SHOCK, DO NOT EXPOSE
THIS EQUIPMENT TO RAIN OR
MOISTURE.

• TO REDUCE THE RISK OF FIRE OR
ELECTRIC SHOCK, AND ANNOYING
INTERFERENCE, USE ONLY THE
RECOMMENDED ACCESSORIES.

• THIS DEVICE IS INTENDED FOR
CONTINUOUS OPERATION.

This product incorporates copyright
protection technology that is protected
by method claims of certain U.S. patents
and other intellectual property rights
owned by Macrovision Corporation and
other rights owners. Use of this copyright
protection technology must be
authorized by Macrovision Corporation,
and is intended for home and other
limited viewing uses only unless
otherwise authorized by Macrovision
Corporation. Reverse engineering or
disassembly is prohibited.

SAFETY INFORMATION

Region Management Information

Region Management Information:
This Mobile DVD Player is designed and
manufactured to respond to the Region
Management Information that is recorded
on a DVD disc. If the Region number
described on the DVD disc does not
correspond to the Region number of this
Mobile DVD Player, this Mobile DVD
Player cannot play this disc.

5

DISC NOTES

Disc formats supported by this player

DVD

12 cm disc
(Single-sided disc only)

Video CD

12 cm disc

CD

12 cm disc

MP3

12 cm disc

Handling and Cleaning

• Dirt, dust, scratches and warping disc
will cause misoperation.

• Do not place stickers or make
scratches on discs.

• Do not warp discs.

• A disc should always be kept in its
case when not in use to prevent from
damage.

• Do not place discs in the following
places:

1. Direct sunlight

2. Dirty, dusty and damp areas

3. Near car heaters

4. On the seats or dashboard

Disc Cleaning

Use a dry soft cloth to wipe the surface.
If the disc is quite dirty, use a soft cloth
slightly moistured with isopropyl (rubbing)
alcohol. Never use solvents such as
benzine, thinner or conventional record
cleaners as they may mar the surface of
the disc.

Note:

A disc may become somewhat scratched
(although not enough to make it
unusable) depending on the way it is
handled and conditions in the usage
environment. Note these scratches are
not an indication of any problem with the
player.

Preparing New Discs with Rough
Spots

A new disc may have rough edges on its
inside and outside edges. If a disc with
rough edges is used, the proper setting
will not be performed and the player will
not play the disc.
Therefore, remove the rough edges in
advance by using a ballpoint pen or
pencil as shown on the right. To remove
the rough edges, press the side of the
pen or pencil against the inside and
outside edges of the disc.

Rough spots
on inside edge

Ball point pen
or pencil

Rough spots on
outside edge

Label side up

Do not touch
the underside
of the disc

Do not bend

Wipe the disc from center
toward the outside edge

30˚

182 mm

53 mm

Front Panel

Outer Trim Ring

L Key

Sleeve

R Key

INSTALLATION

Notes:

• Choose the mounting location where
the unit will not interfere with the
normal driving function of the driver.

• Before finally installing the unit,
connect the wiring temporarily and
make sure it is all connected up
properly and the unit and the system
work properly.

• Use only the parts included with the
unit to ensure proper installation.
The use of unauthorized parts can
cause malfunctions.

• Consult with your nearest dealer if
installation requires the drilling of holes
or other modifications of the vehicle.

• Install the unit where it does not get in
the driver’s way and cannot injure the
passenger if there is a sudden stop,
like an emergency stop.

• If installation angle exceeds 30˚ from
horizontal, the unit might not give its
optimum performance.

• Avoid installing the unit where it would
be subject to high temperature, such
as from direct sunlight, or from hot air,
from the heater, or where it would be
subject to dust, dirt or excessive
vibration.

DIN FRONT/REAR-MOUNT

This unit can be properly installed either
from “Front” (conventional DIN Front­mount) or “Rear” (DIN Rear-mount
installation, utilizing threaded screw holes
at the sides of the unit chassis).
For details, refer to the following
illustrated installation methods.

DIN FRONT-MOUNT (Method A)

Installation Opening

This unit can be installed in any dashboard
having an opening as show below:

Installing the unit

Be sure you test all connections first, and
then follow these steps to install the unit.

1. Make sure the ignition is turned off,
and then disconnect the cable from
the vehicle battery's negative (-)
terminal.

2. Disconnect the wire harness and the
antenna.

3. Lift the top of the outer trim ring then
pull it out to remove it.

4. The two supplied keys release tabs
inside the unit’s sleeve so you can
remove it. One key is for the right side
and the other is for the left side. Insert
the keys as far as they will go (with the
notches facing up) into the appropriate
slots at the middle left and right sides
of the unit. Then slide the sleeve off
the back of the unit.

5. Mount the sleeve by inserting the sleeve
into the opening of the dashboard and
bend open the tabs located around the
sleeve with a screwdriver. Not all tabs
will be able to make contact, so
examine which ones will be most
effective. Bending open the appropriate
tabs behind the dashboard to secure
the sleeve in place.

6

9. Reconnect the cable to the vehicle
battery's negative (-) terminal. Then
replace the out trim ring

Removing the unit

1. Make sure the ignition is turned off,
and then disconnect the cable from
the vehicle battery's negative (-)
terminal.

2. Remove the metal strap attached the
back of the unit (if attached).

3. Lift the top of the outer trim ring then
pull it out to remove it.

4. Insert both of the supplied keys into
the slots at the middle left and right
sides of the unit, then pull the unit out
of the dashboard.

DIN REAR-MOUNT (Method B)

If your vehicle is a Nissan, Toyota, follow
these mounting instructions.
Use the screw holes marked T (Toyota),
N (Nissan) located on both sides of the
unit to fasten the unit to the factory radio
mounting brackets supplied with your
vehicle.

Sleeve

Dashboard

Screwdriver

Tabs

Spring Washer

Tapping Screw

Plain Washer

Hex Nut

Metal Strap

Mounting Bolt

Dashboard or
Console

Side view showing
Screw Holes marked
T, N or S

Factory Radio
Mounting
Bracket

Screw

Screw

INSTALLATION

6. Reconnect the wire harness and the
antenna and be careful not to pinch
any wires or cables.

7. Slide the unit into the sleeve until it
locks into place.

8. To further secure the unit, use the
supplied metal strap to secure the back
of the unit in place. Use the supplied
hardware (Hex Nut (M5mm) and Spring
Washer) to attach one end of the strap
to the mounting bolt on the back of
the unit. If necessary, bend the metal
strap to fit your vehicle's mounting
area. Then use the supplied hardware
(Tapping Screw (5x25mm) and Plain
Washer) to attach the other end of
metal strap to a solid metal part of the
vehicle under the dashboard. This strap
also helps ensure proper electrical
grounding of the unit.
Note to install the short threading
terminal of the mounting bolt to the
back of the unit and the other long
threading terminal to the dashboard.

7

INSTALLATION

To fasten the unit to the factory radio
mounting brackets.

1. Align the screw holes on the bracket

with the screw holes on the unit, and
then tighten the screws on each side.

2. Fasten with the supplied truss screws

(5x5mm) or flush surface screws
(4x5mm), depending on the shape of
the screw holes in the bracket.

Note:

(1) The outer trim ring, sleeve and the
metal strap are not used for method B
installation.

(2) When the unit is on work, if you release
the front panel, the unit will enter into the
power off state automatically, and you
can see the indicater LED flashing. When
you install the front panel the unit will
resume work automatically.

8

THE PLAYER

9

FRONT VIEW

1
2

20

21

23 3

1567101213 4 14

16 25

19

18

5

5

1
2

23 3 15 6 7

10 12 13

4

14 16

9

8

17

11

22

24

Closed Position

Open Position

Remove the front panel:

1. (BACK) 14.

2. AV IN 15. DSP

3. (OPEN/CLOSE) 16. ENT

4.

(EJECT) 17. SETUP

5. Disc Slot 18. LOC

6. MODE 19. MO/ST

7. VOL

+/- 20. BAND

8. + 21. AS/PS

9. - 22. Reset Button

10.

/MUT 23. Remote Sensor

11. 7“ COLOR TFT 24. Front Panel LED

MONITOR

12. S (Smart MODE) 25.

/ , / (Cursor Buttons)

13.

(MENU)

THE PLAYER

10

11

ELECTRICAL CONNECTION

FUSE

0.5A

4-SPEAKER SYSTEM

(GREEN/BLACK)

(GREEN)

(WHITE/BLACK)

(WHITE)

(GRAY/BLACK)

(GRAY)

(VIOLET/BLACK)

(VIOLET)

REAR LEFT
SPEAKER

BRAKE (PINK) Connect to the negative side of the parking brake.

FRONT LEFT
SPEAKER

FRONT RIGHT
SPEAKER

FR (RED)

FL(WHITE)

RR (RED)

RL (WHITE)

(WHITE)

(RED)

(YELLOW)

(WHITE)

(RED)

(YELLOW)

(WHITE)

(ORANGE)

PREAMP OUTPUT

AV-OUTPUT(GRAY)

AV-INPUT(BLACK)

SUBWOOFER OUT(GREEN)

DIGITAL AUDIO(ORANGE)

RGB

REMOTE SENSOR
CONNECTOR (BLACK)

(BLACK)

EXTERNAL REMOTE SENSOR (OPTIONAL)

YELLOW(SYNC)

BLUE

GREEN

RED

ANT(BLACK)

ONE SIDE

MONITOR

DIVERSITY ANTENNA INPUT

2345678

15 14 13 12 11 10 9

TV Tuner is sold separately (Model # TV4)

12

REMOTE CONTROL

LOCATION AND FUNCTION OF KEYS

2

7

34

21

222

22
19
16

17

12

14

13

4

15

9

35

28

5

6

32

27
10

25

30

31

8

11

18

3

20

1

26

33

29

24

23

1

36

13

REMOTE CONTROL

1. Press POWER button to turn the unit ON or OFF.

2. EJECT Press to eject the disc.

3. OP/CL Press to open/close the screen display.

4. SUBT(BACK) Changes of the SUBTITLE language on multi-subtitle language

DVD disc.
In the MENU mode, press BACK can return to the previous

menu.

5. ANG Changing of the view angle on multi-angle DVD disc.

6. CONS Display statistical disc information during playback in DVD mode.

7. MODE Press to change between RADIO, DVD, AV1 , AV2 and RGB

mode.

8. SETUP Display the SETUP menu in DVD mode.

9. PROG Allows the track played in the order you programmed.

10. AUD Changes of the AUDIO soundtrack on multi-audio soundtrack

DVD disc.

11. TITLE(DSP) Display the TITLE menu that is stored in DVD disc.

12. MENU Display the main menu.

13.

/ , / In case of MENU mode, / , / buttons served as cursor

buttons to select item left/right, ahead/back. In FM mode, use
/ to choose the frequency.

14. OK Confirm the Track/Chapter selected with the numeric buttons or

selected with the cursor buttons on screen.

15.

/ Changing for slow forward/ reverse playback motion on DVD

disc.

16. Press to play the disc.

17.

/ Press to start forward rapidly & to reverse rapidly.

18. / Press to skip to the next track & press to skip back one

track.

19.

Press it to stop playback.

20.

Press it to pause playback.

21. 0 - 9 Numeric buttons

22. MO/ST (-/--)

In radio mode press the button to set the reception between
mono mode or stereo mode.In TV mode -/-- button is always
use with 0-9 numeric buttons to select channel.

23. P/N Switch between PAL mode and NTSC mode.

24. S-M Press it to enter SMART MODE function.

25. ZOOM Allows the picture to be increased in size.

26. VOL+ Press VOL+ button to increase the volume level.

27. GOTO (AUTO) In TV mode shortly pressto scan preset station.

Disc search button in DVD mode, cooperatively used with
numeric buttons.

28. RDM Press it to play all tracks on CD in random order.

29. LOC (CLEAR)

In FM mode, press it to select between local and distant stations.
If you press the RESUME button, you can press CLEAR button
to clear the stop point.

14

REMOTE CONTROL

30. VOL- Press VOL- button to decrease the volume level.

31. RPT Switch the Repeat mode of discs.

32. A-B A-B repeat allows a passage to be repeated continuously.

33. AS/PS(BOOKMK) In radio mode, press it to activate Automatic Memory

Storing/Program Scanning function. During playback,
press to enter bookmark function.

34. BAND(PBC) In radio mode, press it to select desired band.

Changing between PBC ON and PBC OFF on the VCD

disc.

35. MUTE In radio, DVD, AV1, AV2 mode, press to mute the

sound.

36.TV-DVD-AUDIO Switch it to select among TV, DVD and AUDIO mode.

15

REMOTE CONTROL

Remote Control

Inserting the Battery

1. Open the battery compartment cover.

2. Insert the new batteries. Make sure
that the positive and negative
terminals of the battery are oriented
as indicated.

3. Close the cover
Battery:

One button cell lithium
battery.

Using the Remote Control

Point the remote control towards the
remote control signal receiver on the player
front face.

Operation angle: About 30 degree in
each the direction of the front of the
remote sensor.

LOADING/EJECTING A DISC

Loading a Disc

1. Turn the ignition on to the accessory
position.

2. Press the button (1).

3. Insert the disc with printed side facing
up into the disc slot (2).

4. The player will start playback
automatically.

Ejecting a Disc

Only in DVD mode, press button (3) to
eject the disc.

1 32

16

OPERATION

BASIC OPERATION

Turning the player on/off

Press and hold

button on the front panel

for several seconds or press

on the

remote control to turn the player on or
off.(Note: Shortly press

button on the

front panel will return the previous menu.)

Open/Close the Monitor and Angle
Adjustment

• Press button on the front panel or

point the remote control to the remote
sensor on the front panel and press
OP/CL button on the remote control,
the monitor will draw out automatically.

When the monitor draws out to a certain
location, it will turn upward automatically
and stop at vertical position.

• Adjusting the viewing angle and

distance. (1)Method A: When the
monitor stops moving, press SETUP
button on the front panel the following
picture will appear on the screen display.

Press SETUP on the front panel to select
Angle or Slide items. Then use +/- buttons
on the front panel to turn the monitor

angel upward/downward in small steps
or
draw the panel in/out to get a desired
viewing position.
(2)Method B:
You can enter the panel setup menu by
pressing MENU button on the remote
control, then select SETUP, in Setup
menu you can select the Panel item to
enter the panel setup menu. Press

/
buttons on the remote control to select
Angle or Slide items. Then use /
buttons on the remote control to turn the
monitor angle upward/ downward in small
steps or draw the panel in/out to get a
desired viewing position.
And you can rotate the monitor left and
right from the central viewing position at
a certain angle range manually. (Note: Do
not rotate the monitor forcibly to avoid
mechanical damage.)

• Return the monitor to the central viewing

position, then press

button on the
front panel or press OP/CL button on
the remote control, the monitor will turn
downward automatically.

When the monitor turns downward to
a certain angle, it will draw in.

OPEN/CLOSE button

Press / buttons on the front panel or
on the remote control to adjust the
selected item. The corresponding value
will show on the display.
In Mode item, you can change the zoom
among: Zoom1, Zoom2, Zoom3, Full(16:9)
and Normal(4:3).

Menu Setup on Screen Display

Press the MENU button and the following
menu will appear on the screen. You can
use

/ , / cursor buttons to move

between the highlight bars in the menu.

Then use ENT button on the front panel
or OK on the remote control to enter the
Audio or Setup menu as follow:

•Audio Menu:

In Bal/Fad menu, use / , / cursor
buttons to adjust the Balance and the
Volume level of the front&rear speakers.

17

Remote Sensor

There is a remote sensor on the front
panel. You can point the remote control
handset to the remote sensor on the front
panel and press function keys on the
remote control to control the DVD unit.
The unit is also connected to an external
remote receiver (See the electrical
connection diagram above), and the
function is the same with the remote
sensor on the front panel.

Notes:

7” TFT Display

When the monitor stretches out, the 7”
color TFT display can show the current
state of the unit.

Volume Level Adjustment

Press VOL+/- buttons on the remote
control to increase or decrease the volume
level.
Press MUT on the front panel or MUTE
on the remote control will mute the sound.
Press MUT or MUTE again the sound will
resume.

Mode Selection

Press MODE button on the remote control
to select among RADIO, DVD, TV, AV1,AV2
and RGB mode.

Reset

Press

on the front panel to release the
front panel you will see the Reset button
(See THE PLAYER picture above.) It must
be activated with either a ballpoint pen
or thin metal object. The reset button is
to be activated for the following reasons:

- Initial installation of the unit when all

wiring is completed.

- All the function buttons do not operate.

- Error symbol on the display.

Picture mode Adjustment

Press MENU button on the front panel or
on the remote control to open the setup
menu, select Setup, in SETUP menu
select Picture, the picture menu will show
on the display, use

/ button to select

among Bright, Contrast, Color, Tint (For
the unit with NTSC system) and Mode.

OPERATION

• Setup Menu:

In Wallpaper menu, use / cursor
buttons to change the wallpaper among
Twinkle/Snowfall/Pillar.

In Clock menu, using / buttons to
select the hour and minute. Then using

/ buttons to change the value of the

hour and minute.

In System menu, use / , / Cursor
buttons to select and adjust the
Beep/Clock/Zone on/off, and can adjust
the Time mode between 12/24.

OPERATION

In EQ menu, use / , / cursor
button to change the sound mode.

In Treble menu, use / to select Freq
or Level, use / to adjust the
corresponding item.

In Bass menu, use / cursor button
to adjust Freq/Level/Q.Fac.

In Loudness menu, use / to change
the Loud on or off.

18

19

OPERATION

The operation of Picture menu and Panel
menu please refer to the before
description.

In ZoneCtr menu,you can adjust the the
mode of the front or rear speakers. Use

/ to select front speaker or rear

speaker. Use / to change the speaker’s
mode.
Front mode can be changed among
DVD/TV/ AV1/ AV2/ RGB/Tuner.
Rear mode can be changed among DVD/
TV/ AV1/ AV2.

20

NOTE (FOR THE UNIT WITH TEL-MUTE
AND BRAKE FUNCTION):

• When there is an incoming call, the unit

will be in mute state, and “TEL MUTE”
appears on the screen display.

• If the brake wire isn’t connected to the

ground wire of the parking brake, the
picture will not be shown on the screen
in DVD/TV/AV mode for safety purpose.
Only the audio will be heard.

SMART MODE OPERATION

In any mode, shortly press S-M button
on the remote control or S (Smart MODE)
button on the front panel to enter Smart
Mode function. At this time the front
speaker is the original sound, you can
press the MODE button to change the
front speaker’s state among DVD/
TV/AV1/AV2/RGB/Tuner. The rear
speaker’s state can be changed among
DVD/TV/AV1/AV2 by pressing S-M or S
button. After AV2 mode will exit smart
mode function.

DISC (DVD, VCD, CD, MP3) OPERATION
Switching to DVD mode

Press MODE button on remote control to
select DVD mode (Note: Only there is
a disc in the disc slot, can you enter the
DVD mode.)

Stopping Play

- Briefly press the

(Stop) button to pause
the unit playback, when the (Play)
button is pressed, normal playback will
continue.

- Press (Stop) button twice to stop the
playback and go back to initial
Track/Chapter.

Fast Forward / Fast Reverse

Press & during play.
Each time the button is pressed, the
speed of fast forward

& reverse
changes
according to the disc as follow.

DVD:

Normal Playback X2 X4 X16 X100

VCD/CD/MP3:

Normal Playback X2 X4 X8

OPERATION

Skipping Track

Press / buttons on the remote
control during playback.
Press

to skip to next track, and
to back one track.
Note: For some VCD2.0 discs (PBC­playback control), / buttons may be
unavailable.

Slow Motion Play

During playback each time

/ button
is pressed, the speed of slow forward/
reverse changes according to the disc as
follow.(Note:Only for the DVD disc )

DVD:

Normal Playback 1/32 1/16 1/8

1/2 1/4

Pause (still picture)

Pressing on the remote control during
playback will pause the playback. To return
to normal playback, press on the remote
control.
And you can press and hold button
on the front panel for several seconds to
pause the playback, Press and hold it
again will return to normal palyback.

21

SETUP

REPEAT PLAY/ PARAGRAPH REPEAT
PLAY

Repeat play: When you want to repeat
playing the whole disc or a track or a
chapter in the disc.

1)Press RPT button repeatedly to select
different repeat modes.

2)For different kinds of disc, pressing

RPT button has different effects.

Note: REPEAT feature does not support

VCD2.0 (with PBC ON).

A-B
Paragraph Repeat Play: When you
want to repeat playing a desired
paragraph.
A-B repeat allows a passage to be

repeated continuously.

1) Press A-B button first at the start of

the. required passage.

A -

2) Press A-B button secondly at the end

of the passage.

A - B

3) Then the unit will repeat playing the

passage you just set from A to B.

4) To revert to normal playback, press A-

B button again.

Off

Bookmark Function

During playback, pressing BOOKMK
button on the remote control will enter
into bookmark function.

1) During playback, when you want to set
a bookmark, press BOOKMK button,
the information will appear:

#1 : 1/9

This is to tell you that you have set a

bookmark.

2) If you want to watch the section that
you just set a bookmark, press GOTO
button, then press / buttons to move
the cursor to the desired number of the
bookmark,and press or OK button on
the remote control or ENT on the front
panel to confirm.

1 2 3 4 5 - - - -

! NOTE:

You can press BOOKMK button
repeatedly to set 9 bookmarks, Then press
GOTO button and use / and /OK
/ENT to confirm the track you have
marked. And you can use numeric buttons
(1-9) to select the track directly. CLEAR
button on the
remote control to clear the bookmark you
have set.

Zoom

Allows the picture to be increased in size.
Press ZOOM on the remote control to
toggle among 400% scale, 1600% scale.
During Zoom mode, press

/ , /
buttons to move pictures up, down, left
or right direction.

Random

Pressing RDM button during playback will
start to play tracks in random order.
Press the button again to return to normal
playback.

Note:

This function is effective on VCD, SVCD

and CD.

When playing a VCD/SVCD, the

random playback is effective with PBC
OFF.

Program

(This function is ineffective for DVD disc.)

The function is effective in PBC OFF

mode. In stop or pre-stop mode, press
PROG button can activate program edit
interface.

Chapter

Title

Off

DVD

Track

All

Off

VCD/SVCD
CD/MP3/
WMA

ALL

JPG

Large JPG

12 Level

MP3

Mpg

Video CD

List Program List

0:00:00

22

For how to set the program menu,

please refer to the operation of the
audio files in the media player below.

Note:

• After you have programmed the tracks,
press PROG button can switch
between program play and normal
play.

• Press

or OK button on the remote
control or ENT on the front panel to
exit the edit interface.

DATA DISC AND AUDIO CD PLAY
OPERATION

When you insert a data disc including
audio (MP3, WMA), movie (MPEG),
picture (JPG) files or audio CD into the
disc slot, the following media play
window will be shown on the screen:

1)Press TITLE button to switch between
Music, Photo and Movie these three
pages.

2)In Music page, there are three areas:
Play list, Program list and the Edit area
in the middle.

• Press

or OK button on the remote
control or ENT on the front panel to
open the highlight folder in the play
list or play the audio file in the play
list or program list.

• Use “ADD”, “ADD ALL”, “DELETE”,
and “DELETE ALL” these four
operation buttons on the middle edit
area to edit the program list.

• When highlight is on the audio file of
the play list, you can press PROG
button to add the highlight file
directly to the program list.

• When highlight is on the program
list, you can press CLEAR button on

SETUP

the remote control to delete the
highlight file directly.

3) In Photo page, there are three areas:
Play list, Preview window and the
Edit area in the middle.

• Press

or OK button on the remote
control or ENT on the front panel to
open the highlight folder in the play
list.

• When the highlight stops on the picture
file, the preview of the picture will be
shown in the preview window on the
right.

• When selecting the

(slide show)
button in the middle area and pressing
OK/ENT to confirm, it will start to
display all the pictures in full screen in
turn. When show the picture in full
screen, the control bar will be shown
on the screen.

Press

or button on the remote
control or on the front panel to rotate
the picture 90º counter-clockwise or
clockwise.
Press

/ button on the remote
control or on the front panel to skip to
the previous or next picture.
Press

button to stop slide show.
Press CLEAR button to hide or display
the control bar.

• The

(Speed) button in the middle
area is used to adjust the display
interval speed between the pictures.
Press

/ buttons on the front panel
or on the remote control to switch
between “>”, “>>”, “>>>”and “

”.

ALL

JPG

Large JPG

12 Level

MP3

Mpg

Music

List Program List

0:00:00

Photo Movie

_ _ _ _ 1

_ _ _ _ 2

_ _ _ _ _ _ _ _ _ _ _ 1

soft

_ _ _ _ _ _ _ _ _ _ _ 2

_ _ _

Music

List Preview

Photo Movie

3/15 90º 90º

Prev Next Stop

23

SETUP

4) In Movie page, press or OK button
on the remote control ENT button on
the front panel to open the highlight
folder in the play list or play the
corresponding file.

NOTE:

For audio CD, the play interface and
operation is similar with the Music page
operation. For details, please refer to the
description of Music page above.

Display

When the TFT panel is drawn in,Press the
DSP button on the front panel or on the
remote control during playback to display
the contents of the current disc on the
LCD display.

1-14053_2mpeg

2-BB_MPEGYEMANNVYOU.mpe

3-badluck.mpeg

Music

List

Photo Movie

24

SETUP

01 : 12

(3) Press DSP for the third time:

The message on the screen will be
resume:

DVD ROOT

Multi-audio language function
For DVD

Press AUD on the remote control during
playback. Each time the button is pressed,
the audio soundtrack language changes
on sequential order.
Notes:

- The language number is different
according to the disc.

- Some discs only contain one language
soundtrack.

- When no different language soundtrack
are recorded, will be displayed at

screen left top corner.

For VCD/CD

Press AUD during playback.
It is possible to switch the sound between
monaural and stereo sound.

MONO LEFT MONO RIGHT STEREO

TITLE menu function (For DVD Only)

If the DVD has multiple titles recorded on
the disc. It can select preferred title from
the title menu to start playback.

1. Press TITLE during playback.

- The title menu is display.

2. Press the cursor button shown in

display, select preferred title by the
cursor button and confirm by OK button.

ON-SCREEN DISPLAY FUNCTION

Press the CONS button during playback
to display the console information of the
current disc on the screen.

For DVD

1/1

OFF

0:01:45

1/17

1.ENG
D

3/2.1

Normal

2/32

Sound

Move Select

Example:

MP3:

(1) Press DSP for the first time will display

the elapsed time of the disc:

00 : 00 : 55

(2) Press DSP for the second time will

display the clock:

01 : 17

(3) Press DSP for the third time, the

massage will resume:

MP3 T 01

CD:

(1) Press DSP for the first time:

REPT ALL

(2) Press DSP for the second time will

display the elapsed time of the disc:

00 : 02 : 39

(3) Press DSP for the third time will display

the clock:

00 : 23

(4) Press DSP for the fourth time, The

message on the screen will resume:

CD T 08

VCD:
(1) Press DSP for the first time will display

the elapsed time of the disc:

00 : 03 : 31

(2) Press DSP for the second time will

display the clock:

01 : 03

(3) Press DSP for the fifth time:
The message on the screen will resume:

VCD T 01

DVD:

(1) Press DSP for the first time:

DVD T

(2) Press DSP for the second time will

display the clock:

25

SETUP

1)

1/17

Item: Title
Function: Display the current title

number and the total title number; it
can skip to the desired title number.
Method:

/ buttons or use numeric
buttons to input and confirm with OK
button on the remote control or ENT
button on the front panel.

2)

2/32

Item: Chapter
Function: Display the current chapter

number and the total chapter number;
it can skip to the desired chapter
number.

Method:

/ buttons or use numeric
buttons to input and confirm with
OK/ENT button.

3)

0:01:45

Item: Time
Function: Display the elapsed time;

you can input the time directly to the
skip to the corresponding playback
point.
Method: Use numeric buttons to input
time and confirm with OK/ENT button.

4)

1.ENG
D

3/2.1

Item: Audio
Function: Display the current audio

soundtrack language and digital audio
output; it can switch to other audio
soundtrack language and digital audio
output.
Method:

/ buttons or press AUD

button.

5)

NONE

Item: Subtitle
Function: Display the current subtitle

language; it can switch to other subtitle
language.
Method:

/ buttons or press SUB-

T button.

6)

1/1

Item: Angle
Function: Display the current angle; it

can switch to other angle.
Method:

/ buttons or press ANG

button.

7)

Normal

Item: Sound
Function: Display the current sound

mode; it can switch between normal
and 3D surround effect mode.
Method:

/ buttons.

For VCD:

0:01:45

PBC

Stereo

Normal

Sound

Move Select

1)

PBC

Item: Track
Function: When it is in PBC ON mode,

it display “PBC” (only display, can’t be
changed); when it is in PBC OFF
mode, it will display the current track
number and total track number (such
as “1/16”) and it can skip to the desired
track number.
Method: When in PBC OFF, press

/

buttons or use numeric buttons to
input and confirm with OK/ENT
button.

2)

0:01:45

Item: Time
Function: Display the elapsed time;

you can input the time directly to the
skip to the corresponding playback
point.
Method: In PBC mode, it can’t be

26

SETUP

changed. In PBC OFF mode, use
numeric buttons to input time and
confirm with OK/ENT button.

3)

Stereo

Item: Audio
Function: Display the current audio

mode; it can switch to other audio
mode.
Method:

/ buttons or press AUD

button.

4)

Normal

Item: Sound
Function: Display the current sound

mode; it can switch between normal
and 3D surround effect mode.
Method:

/ buttons.

Multi-subtitle language function (For
DVD only)

Press SUBT during playback.
Each time the button is pressed, the
subtitle language changes in sequential
order.
Notes:

- The language number is different
according to the disc.

- Some discs only contain one subtitle
language.

- When no different subtitle language are
recorded, will be displayed at screen

left top corner.

Multi-angle function (For DVD only)

Press ANG during playback.
Each time the button is pressed, the angle
changes in sequential order.
Notes:

- The angle number is different according

to the disc.

- The function only works for discs having

scenes recorded at different angles.

- When no different angle is recorded,

will be displayed at screen left top
corner.

RADIO OPERATION

• Switching to radio mode

Press MODE button on remote control
to select radio mode.
In radio mode, the following information
will appear on the display.

• Selecting the frequency band

Press BAND on remote control to select
desired band. The reception band will
change in the following order:

FM1 FM2 FM3 AM

• Selecting station

During radio mode, press CH button
on remote control or on the front
panel to increase frequency, press CH

button on remote control or on the
front panel to decrease frequency by
one step of channel spacing. Hold the
button longer for fast tuning. The
frequency is updated correspondingly
on display.

• Setting memory
Press RADIO PRESET buttons (1~6)

on remote control or press

/ on the
front panel to preset stations at radio
mode. With this system, a total of 24
stations can be stored in the memory
of six buttons. Each band stores up to
six preset stations.
The stations might be FM1, FM2, FM3,
AM band. The operation is as below:

- Store in Memory

Press and hold desired memory
location button for several seconds.
The current listening station will be
stored into the number button.

- Retrieve a Preset Station

Press any one of the RADIO PRESET
buttons (1~6) on remote control to
retrieve a station which had been
stored in the memory in advance the
chosen number is shown on display.

• Automatic memory storing & program
scanning

- Program scanning
Shortly press AS/PS button on remote
control or on the front panel to scan
preset station.

27

And it will hold at each station for about
5 seconds.

- Automatic memory storing
Press and hold AS/PS button on remote
control for about several seconds or
press AS/PS button on the front panel,
the radio searches from the current
frequency and checks the signal
strength until one cycle search is
finished.
And then stations are stored into the
preset number button in turn according
to the strength of the stations. When
auto search is finished, it will enter into
preset scan mode automatically.

• Mono/stereo

Press MO/ST button on remote control
to select mono or stereo mode. You
can sometimes improve reception of
distant stations by selecting mono
operation.

• LOCAL/DISTANT

Press and LOC button on the remote
control to select between local and
distant stations.
Local setting for reception of strong
Station, and a distant setting for
reception of weaker stations. This
function is effect during AUTO SEEK
operation.

TV OPERATION

• Switching to TV mode

Press MODE button on remote control
to select TV mode.

• Auto searching TV channels

Press GOTO (AUTO) button on remote
control or press and hold AS/PS button
on the front panel for several seconds,
“SCAN READY” will appear on the
screen display, then press CH

on the
remote control or press button on
the front panel to start search channel
automatically.
In the course of searching, press CH
button on the remote control or button
on the front panel to stop searching.

• Selecting channel

Press CH button on remote control

or button on the front panel to
choose channel upward and press
CH button on remote control or
button on the front panel to choose
channel downward.

OPERATION

The numeric buttons (0,1~9) allow

you to select the corresponding
channel directly.
Press digital select button -/-­cooperatively used with numeric
buttons to select channel desired.
For example, when you want select
16 channel, press -/-- button to switch
between “-“ and “--“, when the “--“
appears on the display, you can press
“1 “button then press “6” button to
select 16 channel.

• Screen display

Press TITLE (DSP) button on remote
control to display the current status
such as TVch. If you don’t operate over
five seconds, the information on the
screen will disappear.

• Note: In TV mode press RPT+GOTO
button on the remote control to change
the TV type among: NTSC, PAL B/C,
PAL I, PAL M, PAL D/K

AV OPERATION

• Switching to AV mode

There is a pair of AUDIO/VIDEO INPUT
jacks on the front and back of the unit.
When you connect an audio/video
system through these jacks, press
MODE button on the remote control or
on the front panel to select AV mode.

RGB OPERATION

• Switching to RGB mode
When you connect the RGB terminals
on the back of the DVD unit to the
corresponding RGB system, then Press
MODE button on the front panel or on
the remote control to select RGB mode,
the RGB signal will appear on the
screen.
Note: When you press MODE button

to select RGB mode and there is
no RGB signal input, then there
is nothing to be shown on the
screen.

28

In DVD mode, when the disc is playing or
in stop mode, press SETUP on the remote
control to enter setup menu.

• When the cursor is on the topside, use
/ buttons to move between the

different pages.

• Press button to move the cursor to

the setup page below and then you can
use

/ buttons to move between the

different setup options.

• Press button to display the choice list

for each setup option and then use /

buttons and ENT button on the front

panel or OK button on the remote
control to change your selection.

LANGUAGE SETUP

• When you open the setup menu, you

will see the language setup page at first,
see below:

LANGUAGE

Menu Language
Disc Audio
Disc Subtitle
Disc Menu

English
English
English
English

SelectMove

t

• “Menu Language” is used to change

the language used in the whole menu
and the all kinds of prompt information
during playback.
The unit has the following languages to
be selected: English, French, Spanish,
German, Italian, Portuguese and
Russian.

• “Disc Audio” is used to set a preset

value for the playback language of the
DVD. When play a DVD disc, if the disc
has a language that atches with the
preset value, then it will play the
language directly; if the disc isn’t
including the language that matches
with the preset, or the disc has the
compelling playback language itself,
then it will play the default language of
the disc.
The unit has the following disc audio
languages to be selected: Original,
English, Spanish, German, Italian,
Portuguese, French, Russian, Chinese
and Other.

Prev. Move Select

SETUP

LANGUAGE

Menu Language
Disc Audio
Disc Subtitle
Disc Menu

Original
English
Spanish
German
Italian
Portuguese
French

Prev. SelectMove

• “Disc Subtitle” and “Disc Menu” are similar
with “Disc Audio”; the function is to set a
preset value for the playback subtitle and
menu display language of the DVD.

DISPLAY SETUP

• When you open the DISPLAY menu, you
will see the following picture:

DISPLAY

TV Aspect
Display Mode
TV Output

4:3
Letterbox
Auto

SelectMove

• “TV Aspect” is used to set the appropriate
display effect when wide-screen video
material is played on a conventional
screen. There are two options to be
selected: 4:3 and 16:9. When a wide­screen TV set is connected, you can select
“16:9” to get better view effect.

• “Display Mode” can be changed when
you set “4:3” in the “TV Aspect”. There
are Letterbox and Panscan to be selected.

Letterbox: Display the picture of the

cinema effect with the black bands at
the top and bottom of the screen.

Panscan: Display the picture of the

clipped TV screen. The left and right
edges are cut off.

• “TV Output” is used to select the TV output
mode. This player can play discs recorded
in either PAL or NTSC format.
Select NTSC format, when the unit is
connected to NTSC TV.
Select PAL format, when the unit is
connected to PAL TV.
Select AUTO format, the player TV output
format will be according to the DVD disc
format.

29

SETUP

AUDIO SETUP

• When you open the AUDIO menu, you
will see the following picture:

AUDIO

Dolby Digital
DTS
Sample Freq.
Digital Output

Bitstream
Bitstream
48kHz
On

SelectMove

• “Dolby Digtial” means the Dolby digital
out type. There are “Bitstream” and
“PCM” to be selected.

Bitstream: When connecting to the

amplifier or other devices with the
Dolby Digital Decoder, DTS Decoder
or MPEG Decoder or other devices,
select this item.

PCM (Pulse Code Modulation):

When connect to the amplifier with
two channels digital stereo, select
this item.
When playing a DVD disc with Dolby
Digital and recorded by MPEG1 or
MPEG2 record system, the DVD
player will output the audio in PCM2
playback mode.

• “DTS” means “Digital Theater System”.
There are “Bitstream” and “PCM” to be
selected.

• “Sample Freq.” means “Sample
Frequency”. Select the Sample Freq.
between 48kHz and 96kHz. The higher
the sample frequency is, the better the
output audio quality is.

• “Digital Output” is to activate the digital
audio output on or off.

LOCK SETUP

• When you open the LOCK setup page,
you will see the following picture.

LOCK

Rating
Password
Country Code

Unlock
New
US

SelectMove

• “Rating” is used to set the parent control
level.

LOCK

Rating
Password
Country Code

Unlock
8 Adult
7 NC17
6 R
5 PGR
4 PG13
3 PG
2 G
1 Kids

SelectMovePrev.

When you enter into this item, the

system will require you to input the
password, only the password is
correct, can you be permitted to
change the parent lock level.

Then you must input the password
“3308”.

If you find it wrong in the course of

inputting the password, press CLEAR
button to clear the inputted character.

When you input the correct

password, you can use

/ buttons
to change the parent level. Here
provide 9 kinds of level including 1~8
and unlock.

Regarding to the levels, please refer

to the “PARENT CONTROL”.

• When you complete the set in the setup,
you must eject/load the disc from the
disc slot, and then the function will
come into effect.

• “Password” setup is used to set the
new password or change the old
password; before you enter into this
item, the system will require you to input
the old password, only the password
is correct, can you be permitted to
change the password.

30

SETUP

• “Load Default” is used to revert to factory
initial settings.

• “Screen Saver” is used to switch on/off
the screen saver function.

• “ Country Code” is used to set the
country code. The code information
standing for original producing area
country will be written in every DVD
disc when it is produced. There are two
characters standing for the name of the
country. For example, CN for China, CA
for Canada, and so on. Only when the
country code you set in the SETUP
menu matches with the disc’s own
country code, the parent level that you
set will come into effect.
The detail operation is:

When you first set this item, it will

display “NEW” and require you to
input a new password, then input the
password again to confirm it.

Then the first character of the

country code will be selected, you
can use

/ buttons to select upward
or downward to confirm the first
character;

When you confirm the first character,

the second character will change into
all the characters that may match
with the first character to stand for
the corresponding country code;

Then use / buttons to select the

second character;

Press ENT or OK to confirm the

setting for country code.

Note:

If you have set a password in “Rating”
and “Password”, when you set the
country code, it will require you to input
the password. Only when the password
is correct, can you be permitted to

change the country code.
If you select “Load Default” in SETUP
menu, the password you have set will be
cleared.

OTHERS SETUP

• When you enter into the OTHERS setup

page, you will see the following picture.

You can change the setting for Load

Default and Screen Saver.

OTHERS

Load Default
Screen Saver

Select
On

SelectMove

TROUBLE SHOOTING

31

If it appears that your DVD unit is faulty,
first consult this checklist. It may be that
something simple has been overlooked.

Under no circumstances should you
try to repair the player yourself, as this
will invalidate the warranty. Only
qualified service personnel can
remove the cover or service this
player.

NO POWER

• Check if the on/off button on the front

of the player is set to on.

• Check if the power plug of the mains

unit is properly connected.

• Check if there is power at the wiring

harness..

NO PICTURE

• Check if the mode is set to proper

state, such as DVD mode, RADIO, TV,
AV and RGB mode.

• Check the video connection.

DISTORTED PICTURE

• Check the disc for fingerprints and

clean with soft cloth, wiping from center
to edge.

• Sometimes a small amount of picture

distortion may appear. This is not a
malfunction.

THE PICTURE IS OVER DARK, OVER
BRIGHT OR HAS NO COLOR

Enter the picture setup menu (refer to the
Picture mode Adjustment above) to adjust
the corresponding item (BRIGHT,
CONTRAST, COLOR or TINT) to proper
value, then you can get an optimum
picture effect.

COMPLETELY DISTORTED PICTURE

• The disc format is not according to the

TV-set used (PAL/NTSC).

DISC DOES NOT PLAY

• Ensure the disc label is upwards.

• Clean the disc.

• Check if the disc is defective by trying

another disc.

NO SOUND

• Check audio connections.

• If using an amplifier, try another sound

source.

• Check if the volume is minimum, and
adjust the VOL+ to increase the volume
level.

NO RETURN TO START-UP SCREEN
WHEN DISC IS REMOVED

• Press POWER to turn off the unit, then
press it again to turn on the unit.

• Press Reset button on the front of the
DVD unit.

THE PLAYER DOES NOT RESPOND TO
THE REMOTE CONTROL

• Aim the remote control directly at the
sensor on the front of the player.

• Avoid all obstacles which may interfere
with the signal path.

• Inspect or replace the remote control
battery.

NO AUDIO AT DIGITAL OUTPUT

• Check the digital connections.

• Check the Digital Audio menu to make
sure that the digital output is correctly
set.

• Check if the audio format of the
selected audio language matches your
receiver’s capabilities.

CAN’T RECEIVE TV SIGNAL OR THE
PICTURE QUALITY IS POOR IN TV
MODE

• Please confirm if the antenna is
connected to the antenna socket of
the TV BOX that connected to the DVD
unit.

• Perhaps the signal in your position is
too weak, and it can’t receive any TV
signal at all.

BUTTONS DO NOT WORK

• Turn the player off and on with the

power on/off button on the front of the
player.

• Press Reset button on the front of the
DVD unit.

SPECIFICATIONS

GENERAL

Power Supply Requirements : DC 12 Volts, Negative Ground
Maximum Output Power : 4 x 80 watts
Current Drain : 15 Ampere (max.)

TV

TV Sensitivity : 45dB V @CH25 in average

RADIO

FM

Frequency Coverage : 87.5 to 107.9 MHz
Sensitivity (S/N = 30 dB) : 4 V

Image Rejection : > 45 dB
Stereo Separation : > 25 dB

AM

Frequency Coverage : 530 to 1710 KHz
Sensitivity (S/N = 20 dB) : 36 dBV
Image Rejection : 45 dB

32

DVD

Signal system : Compositive video 1.0Vp-p 75 Ω
Discs played : (1) DVD-Video disc

5” (12 cm) single-sided, single-layer
5” (12 cm) single-sided, double-layer
(2) Compact disc (CD-DA/CD-R/CD-RW/MP3)

(3) (12 cm) VIDEO CD

Monitor Screen Size : 7.0” TFT
Resolution : 1440 x 234 dots

Note:

Specifications and design are subject to modification, without notice, due to
improvements in technology.

SPECIFICATIONS

33

This product incorporates copyright protection technology that is
protected by method claims of certain U.S. patents and other intellectual
property rights owned by Macrovision Corporation and other rights
owners. Use of this copyright protection technology must be authorized
by Macrovision Corporation, and is intended for home and other limited
viewing uses only unless otherwise authorized by Macrovision
Corporation. Reverse engineering or disassembly is prohibited.

88-V3690-06