Boss Audio Systems BV9355B, BV9350 User Manual

Download

Page 1

10 R - 02 1011

Page 2

Warnings

When Driving

Keep the volume level Iow enough to where it allows you to be aware of the road and traffic conditions.

CAUTION

In some countries, it's unlawful to operate a vehicle while video is displayed in the driver's viewing area. Please always switch the unit's display to "Font Type Display" mode by pressing the DISP button while driving. For safety reason, the driver should only enjoy / watch the video while the car is in parking mode.

When Car Washing

Do not expose the product to water or excessive moisture. This could cause electrical shorts, fire or other damage.

CAUTION

In order to avoid any accident, the driver must not watch video while driving. This unit is designed to not allow watching video while driving. Park your car in a safe place and engage the 'parking brake' before watching video.

When Parked

Parking in direct sunlight can produce very high temperatures inside your vehicle. Give the interior a chance to cool down before starting playback.

Use the Proper Power Supply

This product is designed to operate with a 12 volt DC, negative ground battery system (the regular system in a North American car).

USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OR PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE. DO NOT OPEN COVERS AND DO NOT REPAIR BY YOURSELF PLEASE REFER SERVICING TO A QUALIFIED TECHNICIAN.

NOTE:

1. TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE.

2. TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, AND ANNOYING INTERFERENCE, USE ONLY THE RECOMMENDED ACCESSORIES.

3. THIS DEVICE IS INTENDED FOR CONTINUOUS OPERATION.

This product incorporates copyright protection technology that is protected by method claims of certain U.S. Patents and other intellectual property rights owned by Macrovision Corporation and other rights owners. Use of this copyright protection technology must be authorized by Macrovision Corporation, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision Corporation. Reverse engineering or disassembly is prohibited.

Protect the Disc Mechanism

Avoid inserting any foreign objects into the slot of this player. Failure to follow this may cause malfunction or permanent damage due to the precise mechanism of this unit.

CAUTION

THIS MOBILE DVD PLAYER IS A CLASS I LASER PRODUCT. THIS UNIT USES A VISIBLE/INVISIBLE LASER BEAM WHICH COULD CAUSE HAZARDOUS RADIATION IF EXPOSED DIRECTLY. BE SURE TO OPERATE THE MOBILE DVD PLAYER CORRECTLY AS INSTRUCTED.

E - 2

Page 3

Installation

INSTALLATION CAUTION

1. Before finally installing the unit, connect the wiring temporarily and make sure it is all connected up properly and the unit and system work properly.

2. Use only the parts included with the unit to ensure proper installation. The use of unauthorized parts can cause mal functions.

3. Consult with your nearest dealer if installation requires the drilling of holes or other modifications of the vehicle.

4. Install the unit where it does not get in the driver's way and cannot injure the passenger if there is a sudden stop, like an emergency stop.

5. If installation angle exceeds 30° from horizontal, the unit might not give its optimum performance.

6. Avoid installing the unit where it would be

subject to high temperature, such as from direct sunlight, or from hot air, from heater, or where it would be subject to dust dirt or excessive vibration.

7. Be sure to remove the front panel before

installing the unit.

Attach the trim ring

Trim ring

Installation using the screw holes on the side of the unit

Select a position where the screw holes of the bracket and the screw holes of the main unit become aligned (are fitted) and tighten the screws at 2 places on each side.

Factory radio mounting bracket

Hook

Screw

Hook

Screw

Installation with the half sleeve

After inserting the half sleeve into the dashboard, select the appropriate tab according to the thickness of the dashboard mterial and bend them inwards to secure the holder in place.

Dashboard

182

111

Half Sleeve

Screw

Dashboard or console

Note: The outer trim ring,and half-sleeve are not used for this installation.

Note: The mounting box, metal half sleeve, hook & screws are not included in the packnig.

RESETTING THE UNIT

After releasing the front panel, use a stick or any non-metalic object to press & hold the reset button for five seconds to reset the unit.

Reset Button

E - 3

Page 4

Connecting the System

Wiring Diagram - Power / Speakers

BRAKE ( )

PA RK I N G

PINK

FUSE

2.5m extension wire (not included)

Connect to Parking Brake.

20-PIN

AUDIO/POWER

HARNESS

(See Figure 1 )

WHITE

RED

WHITE

RED

L-C

-C R

-C L

-CH R

Ground

Brake Switch

GREY

REAR CHANNEL

FRONT

CHANNEL

BLUE/WHITE

STRIPE

POWER

AMPLIFIER

REMOTE

VIDEO IN

AUDIO IN LVIDEO OUT 1SUB-W

CAMERA AUDIO IN R

(Not supplied)

RCA-TO-RCA

CABLES

AMP

Connect to power amplifier, if not used, tape bare end of wire.

ANTENNA JACK

ANTENNA EXTENDER CABLE

ORANGE

REVERSE(+)

OVERRIDE

CONNECTOR B

Figure 2

ISO CONNECTOR 4 PIN + 8 PIN FEMALE WITH MALE TERMINAL

ISO CONNECTOR WIRING CHART

PIN WIRE COLOR FUNCTION / LABEL

YELLOW

A4 A5

BLUE RED

A7 A8

BLACK VIOLET

VIOLET / BLACK

GREY

B3 B4

GREY / BLACK WHITE

B5 B6

WHITE / BLACK GREEN

GREEN / BLACK

BATTERY(+) POWER ANTENNA IGNITION(ACC) GROUND RIGHT REAR SPEAKER (+) RIGHT REAR SPEAKER ( ) RIGHT FRONT SPEAKER (+) RIGHT FRONT SPEAKER ( ) LEFT FRONT SPEAKER (+) LEFT FRONT SPEAKER ( ) LEFT REAR SPEAKER (+) LEFT REAR SPEAKER ( )

WIRE

ISO CONNECTOR (See Figure 2)

CONNECTOR A

Gearbox Switch

R N D 2 L

Reverse gear signal

Connect to Back Lamp Lead +

11 12

20 PIN AUDIO / POWER HARNESS

20 PIN HARNESS PIN CHART

PIN WIRE COLOR FUNCTION / LABEL

GREY / BLACK

GREY VIOLET

3 4

VIOLET/BLACK

RIGHT FRONT SPEAKER ( ) RIGHT FRONT SPEAKER (+) RIGHT REAR SPEAKER (+) RIGHT REAR SPEAKER ( )

GREEN

6 7

GREEN / BLACK

RED BLACK

RED

WHITE

WHITE / BLACK

BLUE/WHITE

BLUE YELLOW

15 16

BLACK WHITE

17 18

RED

BLACK

WHITE

LEFT REAR SPEAKER (+) LEFT REAR SPEAKER ( ) IGNITION (ACC) REAR PRE-AMPLIFIER LINE OUT COMMON RIGHT REAR PRE-AMPLIFIER LINE OUT LEFT FRONT SPEAKER (+) LEFT FRONT SPEAKER ( ) POWER AMPLIFIER REMOTE (+) POWER ANTENNA BATTERY (+) CHASSIS GROUND LEFT FRONT PRE-AMPLIFIER LINE OUT RIGHT FRONT PRE-AMPLIFIER LINE OUT FRONT PRE-AMPLIFIER LINE OUT COMMON LEFT REAR PRE-AMPLIFIER LINE OUT

E - 4

Figure 1Pin View

Page 5

Name Of Buttons and Theirs Functions

Source Unit

No.

Item

PWR (POWER)

(PLAY/PAUSE)

SOURCE

CAPTURE

CLOCK

(MUTE)

Decriptions

Press this button to turn the mute On / Off.

Press this button or any other button on the front panel to turn the unit on. Hold & press this button again to turn the unit off.

Press this button to Pause / resume Play the music under Media player mode.

Press this button to select different source playback mode: TUNER/DISC/USB/SD CARD/BT AUDIO/AV IN MODE

During video/image playback, press this button can capture images and store them (up to 10 images) to set as wallpaper. You can also capture an image from an auxiliary video device, if connected.

Press this button to enter into the Clock mode, press this button again then return previous mode.

E - 5

Page 6

Name Of Buttons and Theirs Functions

(EJECT)

VOLUME +

VOLUME

DISC SLOT

SD CRAD SLOT

( The SD Card slot behind the SD Card door.)

USB SLOT

( The USB slot behind the USB door.)

Press this button to eject the Disc.

Under the tuner mode, press this button access Auto Seek mode. Under the media player mode, press this button to skip backward of the previous chapter.

Under the tuner mode, press this button access Auto Seek mode. Under the media player mode, press this button to skip forward

of the next chapter.

Press this button to increase the volume.

Press this button to decrease the volume.

Insert the disc into CD slot. The CD will begin to play.

This unit can support playback MP3/WMA/JPEG/MPEG4/DIVX format which are stored on the SD Card.

This unit can support playback MP3/WMA/JPEG/MPEG4/DIVX format which are stored on the USB memory stick.

AUX IN JACK

( The AUX IN slot behind the AUX IN door.)

This unit is allowed to connect with external Audio/Video system such like Digital Camera or Game Console. User can connect the external A/V system thru the A/V in jack on front panel.

E - 6

Page 7

Name Of Buttons and Theirs Functions

Remote Control

No. Button

Item

Decriptions

POWER ON

OFF

When the unit is power on, long press this button to turn Off

the unit. Once the unit power off, press this button to turn On

the unit.

MUTE

SOURCE

Press this button to turn the mute On / Off.

Press this button to enter into the SOURCE mode. Long press

this button to enter into the Bluetooth transfer mode.

AUDIO

2 ZONE MODE

VOLUME +

VOLUME -

AUDIO

Once the

Dual zone turns on, press this button to change Front

zone or Rear zone.

Press this button to increase the volume.

Press this button to decrease the volume.

Press this button to enter into the AUDIO mode.

Under the tuner mode, press this button to access the Manual

Seek mode.

Under the media player mode, press this button fast forward

through the music under media player mode.

Under the tuner mode, press this button to access the Manual

Seek mode.

Under the media player mode, press this button fast backward

through the music under media player mode.

E - 7

Page 8

Name Of Buttons and Theirs Functions

UP/DOWN LEFT/RIGHT

ENTER

PLAY/PAUSE

BAND

ESC

NUMERIC

BUTTONS

Use these buttons to move cursor up/down/left/right.

Under the tuner mode, press this button access Auto Seek mode. Under the media player mode, press this button to skip backward of the previous chapter.

Under the tuner mode, press this button access Auto Seek mode. Under the media player mode, press this button to skip forward

of the next chapter.

Use this button to confirm the selection.

Press this button to Pause / resume Play the music under media player mode.

Press this button to return previous menu. Under the tuner mode, press this button to access the BAND mode.

Press this button to quick return previous menu or playback mode.

When playback the media use for track or file number direct access and use when function need numeric selection or input.

201

GOTO

ZOOM

ANGLE

DIMMER

CLOCK Press this button to enter into the Clock mode.

CAPTURE

FUNCTION

During video/image playback, press this button can capture images and store them to set as wallpaper.

Press this button to enter into the function mode.

Under tuner mode,press this button to Show The List of stored station.

Under the Media playback mode, press this button to list the

LIST

searching of Tracks or Files on the Media playback mode.

Under the DVD/MP4 mode, press this button to list the searching of DVD Root Menu or Files on the playback mode.

Under the VCD mode, press this button to turn On/Off thePCB function.

GOTO

ZOOM

Under the DVD mode, press this button to pop up the search Menu.

When playback the DVD, press this buttonrepeatedly increases the magnification level.

ANGLE

DIMMER

Under DVD mode, press this button while playing a scene recorded with multiple angles to change the angle.

Press this button adjust the screen brightness.

INFO

DISC

AUDIO

SUB

TITLE

INFO

DISC AUDIO

SUBTITLE

TITLE

Press this button to viewing the information.

Under DVD mode, press this button during playback to change

the audio language.

Under DVD mode, press this button during playback to turn on/off subtitles and change the subtitles.

Under DVD mode, press this button to bring up the Title Menu.

E - 8

Page 9

General Operations

1 2 3 4

94.70P3

SOURCE

Under the SOURCE menu, the below options are available for selection:

Please note not all the Optional Source / feature is available with each unit.

POWER OFF

Tap button to power off the unit, and the below display will be shown on TFT:

SETUP

NOTE

5678

HOME MENU

Tap button on the display enter into the Home Menu, and there have SETUP, SOURCE,OFF options for selection.

SETUP

Under the SETUP menu, the below options are available for selection:

SETUP

See You

MOTION PICTURES DISPLAY

MODE

The units have 4 different types of motion

pictures that can be displayed on TFT

under playback Mode. Tap button on

display to repeatedly can switch between the

4 difference modes.

Tap button is Clock &Date diaplay

mode

Tap button is Virtual Aqua display mode

Tap button is DEMO mode

E - 9

Page 10

General Operations

TIPS

DEMO display mode demonstrates the major highlight functions that are available on this unit.

Tap button is Monitor Off mode

TIPS

To turn back on, touch anywhere on the display or press any button on the front panel.

NOTE

Tapping button switches thru each of the three different Motion Picture modes. The TFT screen will have around 1-2 seconds ‘BLANK’ screen (dark screen). This is normal because during these 1-2 seconds BLANK screen it is re-loading the next motion pictures.

iX-BASS

Tap button to quickly enter into the

iX-Bass function.

SUBWOOFER

Tap button to quickly enter into the

Subwoofer function.

MUTE BUTTON

Tap button to mute on the audio volume, Tap this button again to restore volume to the previous setting.

TFT BACKLIGHT DIMMER

CONTROL

User can adjust the TFT backlight on the

screen. Tap button on display to

adjust the Dimmer level between High / Mid /

Low.

GALLERY DISPLAY MODE

Tap button to preview the captured

images which stored in My Image, and set it to

wallpaper.

TIPS

For details operation of My Gallery, please refer to page of Wallpaper Setting.

PRESET EQ MODE

Tap button to quickly enter into the

EQ menu select different types.

E - 10

Page 11

SetUp Menu Operations

1 3 5 7

24 68

AUDIO MENU

Tap button to access into the Audio Menu. The below audio setting can be select:

iX-Bass

1. Level: adjust the iX-BASS level from Low, Middle or High.

2. P.FREQ: adjust the iX-BASS peak frequency as 400Hz, 800Hz or 2.4KHz.

Sub-W

1. Level: adjust the Subwoofer lever from 00 to12.

2. LPF: adjust the Low pass filter (LPF) as Flat, 80Hz, 120Hz or 160Hz.

Bass

1. Level: adjust the Bass level from-06 to +06.

2. C.Freq: adjust the Bass centerfrequency as 60Hz, 80Hz, 100Hz, or 200Hz.

3. Bass-q : adjust the Bass Quality Factor as 1N, 2N, 1W or 2W.

Treble

1. Level: adjust the Treble level from -06 to+ 06.

2. C.Freq: adjust the Treble center frequency (C.FREQ) as 10KHz, 12.5KHz, 15KHz, or

17.5KHz

Middle

1. Level: adjust the Middle level from-06 to + 06.

2. C.Freq: adjust the Middle Range center frequency as 500Hz, 1KHz, 1.5KHz, or

2.5KHz.

3. Mid.q: adjust the desired Middle Quality Factor to 1N, 2N, 1W or2W.

Balance

To adjust the Balance between the right and left speakers from R12 to L12. Balance Center for this unit is Balance C00.

Fader

To adjust the Fader between the front and rear speakers from R12 to F12. Fader Center for this unit is Fader C00.

SYSTEM MENU

Tap button to access into the System Menu. The below system menu setting can be select:

Date Set

Press the Volume Up / Down or Touch screen

& buttons to adjust the

Date / Month / Year.

Clock Set

Press the Volume Up / Down or Touch screen

& buttons to adjust the

Hour / Minute / AM/PM.

Beep Tone

To adjust the Beep Tone On / Off. The beep tone feature allows the selection of an audible beep tone to be heard each time a button is pressed on the face of the radio. "BEEP TONE ON" is the default display.

Program Volume

This option allows the adjustment of the

volume level of the radio will automatically

Treble

1. Level: adjust the Treble level from -06 to+ 06.

2. C.Freq: adjust the Treble center frequency (C.FREQ) as 10KHz, 12.5KHz, 15KHz, or

17.5KHz

assume when To program a

specific turn on volume level. Touch

screen & buttons to

select “VOLUME LEVEL” level from 00 to 46.

-1E 1

the unit turn on.

Page 12

SetUp Menu Operations

PRESET EQ SETTING

Tap button to access into the EQ Menu. Under the Preset EQ Setting, there are the below 8 different types of preset equalizer available for user selection.

Bluetooth Setting Menu

Tap BT logo button on display to access into the Bluetooth Menu. The below Bluetooth Setting can be select:

Pairing

This feature is used for the pairing of this unit's Bluetooth system to mobile phone or other Bluetooth device. Under the “Pairing” mode, touch screen button to activate the Pairing.

Paired (audio)

In this Menu will displayed the list of Paired Audio Device with this unit.

NOTE

This unit can paired up to 8 devices with Handsfree and / or Audio Device.

TIPS

User can select the paired Audio Device from the list for dis-connect or delete it from the list, please refer to page of

“Pairing, Connecting And Deleting With A Bluetooth Device”.

Auto Answer

This unit is default in “Off” mode. If “On” is selected, the unit will automatically answer any incoming call without the need of pressing the PHONE button.

Phone Vol

This unit can preset the ringing volume level for any incoming call. User can press the

or touch screen buttons to adjust from Min 00 to Max 46.

2-Zone

TIPS

Please refer to “Pairing, Connecting And Deleting With A Bluetooth Device” for

the details operation of “Pairing”

Paired (handfree)

In this Menu will displayed the list of Paired Mobile Phone with this unit.

NOTE

This unit can paired up to 8 devices with Handsfree and / or Audio Device.

TIPS

User can select the paired Mobile Phone from the list for dis-connect or delete it from the list, please refer to page of

“Pairing, Connecting And Deleting With A Bluetooth Device”.

Tap button to access into the 2-Zone menu.

1. If Front Zone is selected, press the volume Up / Down to navigate through different modes: Tunner > BT are available for selection of the Front Zone or AV output.

2. If Rear Zone is selected, press the volume Up / Down to navigate through different modes: Tunner > Disc > Card > BT > AV-1 > AV-2 are available for selection of the Rear Zone or AV output.

Image Setting

Tap button to access into the Image Setting Menu. In this menu user can select his/her favor image use as wallpaper on the playback mode. There is two sources of image for selection:

E - 2 1

Page 13

SetUp Menu Operations

My Gallery

This unit contains 10 pre-loaded images. User can select these 10 pre-loaded images set as wallpaper on the playback mode.

My Image

This unit allows the user to self-capture from VIDEO or JPEG picture. User can select these 10 pre-loaded pictures set as Wallpaper.

Default

This option allows the user to change the background screen from wallpaper to factory default screen.

NOTE

If you don’t like the pre-loaded pictures,

you can press button to

select Erase Current or Erase All.

Dimmer

To adjust the TFT Backlight level between High / Mid / Low.

Calibration

Tap button on the Display Setting menu screen to start the Calibration setting.

Free Memory

This feature allows the user to check the remaining memory capacity of images for capture.

TIPS

This unit max can capture 10 images and pre-store into My Image.

Display Setting

Tap button to access into the Display Setting menu, and there are have below options for selection:

Standby

Under “Ignition On But Power Off” condition, this unit have the following different types of Standby display for selection:

Information

Touch screen button to view this unit system software version.

Standby Off: To turn off the unit. Clock: To display the Clock on TFT. Aquarium: To display the Virtual Aqua

Screen on TFT.

Demo: To automatically demo this unit's

major features.

E - 13

Page 14

Tuner Operation

BAN D

162 3 4

Under the SOURCE menu, tap button access into the Tuner playback mode.

LIST MENU

Local Seek

This feature is used to designate the strength of the signals at which the radio will stop during automatic tuning. "Distance" is the default, allowing the radio to stop at a broader range of signals. To set the unit to select only strong local stations during automatic tuning, tap bar to select the local ON/OFF.

Tuner Area

This option allows the selection of the frequency spacing which is most appropriate for the status the unit is in, U.S.A, EUROPE.

AF On/Off

Tap bar to change AF in On or Off mode.

Tap button access into the Store List to

select the desired station to Recall.

Tap buttons to access the

Auto Seek mode. Long tap these buttons to

access the Manual Seek mode.

BAND

Tap button to change between FM bands and or AM(MW) bands.

FUNCTION MENU

Tap button access into the Function Menu, and there have below functions are allow to operation:

TUNING UP/DOWN

BA N D

Manual Store

Use this function to saved the current frequency to memory station.

Auto Store

After Auto Store saves (all) 6 stations, it will automatically enter present scan one time.

TA On/Off

Tap bar to change TA in On or Off mode.

PTY Seek

Tap button access into the PTY list to select the desired PTY mode. There have below programs type for selection:

MUSIC GROUP

POP , ROCK NEWS, AFFAIRS, INFO

EASY, LIGHT

CLASSICS, OTHER

JAZZ, COUNTRY

NATION , OLDIES

FOLK , TEST, ALARM

AF, TA & PTY only appearing in the function list, after changed the Tuner Area to “Europe”.

RDS INFORMATION

Tap button to view theRDS information of the unit.

SPEECH GROUP

SPORT, EDUCATE, DRAMA

CULTURE, SCIENCE, VARIED

WEATHER,FINANC, CHILDREN

SOCIAL, RELIGION, PHONE IN

TRAVEL, LEISURE, DOCUMENT

NOTE

E - 4 1

Page 15

Media Player Operations (Disc/USB/SD Card)

This unit can play various video/audio formats stored into Disc / USB or SD Card on Media Player.

The following chart helps you to check if a disc is supported by this unit, as well as what functions are available for a given disc type.

Disc format

Digital Versatile Discs (DVDs)

Video CDs (VCDs)

DigitalVersatileDiscsRecordable (DVD+/-R)

DigitalVersatileDiscsRewritable (DVD+/-RW)

Compact Discs (CDs)

CD Recordable (CD-R)

Unsupported Discs

8 cm Disc CDV, CDI, CDG, LD DVD RAM

Note on Region Code

DVD players and DVD Video discs have their own Region Code numbers. This unit can play the disc of all region code numbers.

ALL

Disc Maintenance

Before playing, wipe the disc using a clean cloth, working from the center hole towards the outside edge.

Never use benzene, thinners, cleaning fluids or anti-static liquids or any other solvent.

CD Rewritable (CD-RW)

Audio Format

Playback CD-DA and MP3 or WMA digital music file on CD-ROM or DVD-ROM or USB or Memory Card.

Note of MP3 and WMA:

Support Maximum 2000 files Maximum 30 characters display Supported Sampling frequencies; 32kHz,

44.1kHz, 48kHz. Supported Bit-Rates: 64-256 kbps variable bit rate

Video Format

Playback IMAGE JPEG, DVD Video, MPEG4 . on CD-ROM or DVD-ROM or USB or Memory Card.

Noted of MPEG4

Supported decoding MPEG-4 video defined by ISO 14496-2 Standard:

1. Simple Profile (SP) and

2. Advance Simple Profile (ASP) Supported file format: MP4 and .M4a (audio only)

NOTE

A disc may become somewhat scratched (although not enough to make it unusable) depending on you handle it and conditions in the usage environment. Note these scratches are not an indication of any problem with the player.

Label side Up

Do not bend

Never touch the under side of a disc

Wipe the disc surface from the center to the edge.

E - 5 1

Page 16

Media Player Operations (Disc/USB/SD Card)

Get into the SOURCE menu to select Disc, USB, SD Card Media Player playback mode.

General Operation

12345

LIST MENU

Repeat

ONE: play the current track repeatedly.

FOLDER: play all track sin the current folder repeatedly.

OFF: Repeat Off to cancel all the Repeat function.

Random

During the disc playback, select Random “On” to play all tracks on a Disc in Random order, select Random “Off” will stop the Random play.

Insert the USB Stick

Tap button to view the songs list and

tap buttons to select the desired song,

then tap button start to play.

Tap buttons to move to the next track on the Disc, The selected track number will appear on the display. Press and hold the these buttons for more thanone second to fast forward or fast rewind through the media. Disc play when the button is released.

PLAY / PAUSE BUTTON

Tap button to suspend music play. Tap this button again to resume music play.

FUNCTION MENU

Tap button access into the Function Menu, and there are have below options for selection:

TRACK SELECT

CAUTION

This unit does not support any portable Hard disk / drive.

WARNING

Before remove the USB stick from the front panel. Always remember to switch off the unit's power or switch to other mode then remove out the USB Stick. Never try to remove the USB Stick while playing music file on the USB stick. It may damage the USB Stick and may cause permanent damage to the unit will caused the unit system lock up.

E - 6 1

Page 17

Media Player Operations (Disc/USB/SD Card)

Insert the SD Card

Cli kc

Mode Change to SD Card

After a SD Card was inserted into the main unit card slot. The unit will automatically start playing the files contained on the SD Card.

NOTE

If no SD Card is inserted into the main unit card slot, the unit will return to previous mode.

ikCl

E - 7

Page 18

DVD Operations

Once a DVD disc is inserted into the unit, the unit will automatically start the playback from the beginning of the disc.

NOTE

If the DVD menu appears, touch the display in the desired place to show the controls for item selection.

Touch / / / to move the cursor, then touch to confirm.

Playing DVD Disc

ANGLE

Touch button while playing a scene recorded with multiple angles to change the angle.

TOP MENU

Touch button to bring up the Top Menu on the DVD.

NOTE

Some of the above features may not be available, depending on the type of disc.

Touch button to bring up the Menu on the Disc.

216 3 457

LIST MENU

Tap button to open the DVD control menu, which contains the following:

DVD AUDIO

For DVD, the Audio language can be change if the Disc is record with multilingual tracks. Touch

to select the Audio language / format.

1. Touch these buttons to skip foward to the beginning of the next or previous chapter.

2. Long touch these buttons to fast forward or fast rewind through the Disc. Touch these buttons again to resume normal playback.

PLAY / PAUSE BUTTON

1. Tap button topause playback.

2. Tap button againto resume normal

playback.

TRACK SELECT

SUBTITLE

Touch button to turn on / off the Subtitle language and to change the Subtitles.

3. Long tap button is forward to the

next picture in the video (DVD and VCD only.)

E - 8 1

Page 19

DVD Operations

FUNCTION MENU

Tap button access into the Function Menu, and there are have below options for selection:

Repeat

Repeat “CH” current

Repeat “Title” the current title.

Repeat “ Off ” to cancel all the Repeat function.

the chapter.

to repeat playback the

to repeat playback

Disc Audio

During playback to change the audio language (DVD/Divx only).

Video Setting

Top button access into the Video Setting mode, the below Setup menu will appear:

DVD Setup

Under the DVD Setup mode, there are have below options for selection:

Aspect Ratio: Selecting the TV Aspect setting allows the user to select the aspect ratio of the TV (DVD and VCD only). The following options are available:

4:3 = Aspect ratio of TV is 4:3. 16:9=Aspect ratio of TV is 16:9. Both wide screen and 4:3 contents will fill the entire screen.

TV Signal: The Video setting allows the user to select the TV standard (DVD and VCD only). The following options are available:

NTSC= TV is NTSC. PALcontent isplayed at

NTSCresolution andframe rate

(factory default).

PAL= TVis PAL.NTSC contentis playedat

PALresolution and rame rate.

AUTO= If the content isPAL, the output is PAL.

If the content is NTSC, the output is NTSC.

Default

Setting the Default on will reset all options of Media function setting to factory defaults setting.

Change the Bright level from 01 to 10.

Change the Contrast level from 01 to 10.

Change the Color level from 01 to 10.

Reset to default setting

Close the Setting menu

INFORMATION

Tap button to view the Disc information of the unit.

VIDEO SETUP

Tap button to quickly enter into the video setup mode.

-9E 1

Page 20

MPEG4 Opeartions

The unit is support playback MPEG4 files , Tap

button enter into the Disc List to select

the Movie mode to light up the MPEG4

playback.

OPEN

The details operation is exactly the same as Media Playback operation. The following are special functions pertaining to the playback of File:

Central = Include Albanian, Croat,

European

Polish, Romanian, Slovak, Slovene and Sorbian.

Cyrillic = Include Bulgarian, Belorussian, English, Macedonian,Moldavian, Russian, Serbian and Ukrainian.

Czech, Dutch, English,

German, Hungarian,Irish,

NOTE

User can tap button into the MPEG4 Function to select the MPEG4 Subtitle.

Mpeg Subtitle

Mpeg Subtitle setting is used for choosing the language domain, ( only for MPEG4). After select one language domain ( alphabet), when playback a MPEG4 with external subtitle, the subtitle display will use this language alphabet. if you find the displaying subtitle “ alphabet ” are not correct. please make sure to select the correct external subtitle language domain. The following language domains are available:

Western = Albanian, Breton, Catalan,

European

Danish, Dutch, English, Faroese,Finnish, French, Gaelic, German, Icelandic, Irish, Italian,Norwegian, Portuguese, Spanish and Swedish.

Turkish =

Include Dutch, English, Finnish, French, Gaelic, German, Italian, Kurdish (Latin), Norwegian, Portuguese, Spanish, Swedish and Turkish.

Albanian, Danish,

E - 20

Page 21

Dual Zone Operation

This unit is equipped with the most advance “Dual Zone” feature. This function is useful if the user would like to select different modes of the Audio and Video output source for Front and Rear Speakers and TFT Screens. For example, user can select to listen to Tuner music for front speakers and rear speaker for DVD movie.

To Switch On Dual Zone Mode

1. “Off” is the default setting.

2. Under SETUP menu, tap button access into the Dual Zone mode, and then tap select to 2-Zone on.

2. When DUAL ZONE is turned“On”, the Source button is used to change Front source & Rear source. Press the Source button repeatedly to change between Front and Rear.

3. The TFT screen will display the Rear Source mode. User can to make the desired operation on the Rear Source's function on the Front Panel or Remote Control.

4. The will automatically switch

TFT screen back to the Front Source after 10 seconds. And the Front Panel buttons and Remote now is resumed to operate for Front Source's function again.

The Default Setting When Dual Zone is “On”

1. The default source / mode for Front ZONE is Tuner & for Rear ZONE is “DVD”.

The Available Playback Mode

1. Front Zone: Tuner and BT modes are available select for playback on Front Zone.

2. Rear Zone: Tuner , Media (Disc/USB/SD), AV modes are available select for playback Rear Zone.

NOTE

AV-1 & AV 2 are considered as the same mode/source in the DUAL ZONE function. So if either the Front or Rear Source is set to AV-1 or AV-2 mode, The other ZONE is not allowed to select the AV-2 or AV-1 Mode eg: If F-Zone is selected “AV-1”, then R-Zone is not allow to have ”AV-2”.

To Operates Function of Front / Rear Soures

1. The Front Panel & Remote control, is

defaulted to control the FRONT source's function / operation.

2. The default Volume level is “12” for both Front & Rear ZONE audio output. (or the Volume Level set as VOL PGM Level set in the Menu).

3. The TFT screen is defaulted to display the Front Mode.

4. When Dual Zone is “On”, some of the AUDIO FUNCTION, EQ FUNCTION and SOURCE WILL NOT BE FUNCTIONAL.

To Switch Off Dual Zone Mode

Under SETUP menu, tap button access into the Dual Zone mode, and tap button select to 2-Zone off.

The Default Setting When Dual Zone Is In “off” Mode

The default audio output reverts to what the user selected for the FRONT Zone source when DUAL ZONE IS “OFF”. For example: When the DUAL Zone is “ON “, user has selected DVD for Front ZONE & Tuner for Rear ZONE. Once DUAL ZONE is turned “OFF”, Audio Output for all 4 speakers becomes “DVD” mode.

E - 1 2

Page 22

AV-In Mode

Select the AV Mode

You can connect up to 2 optional devices, tap

button on display to enter into the AV mode.

AV - 1 = Front panel AV in AV - 2 = RCAback of unit

AV -1

This unit is allowed to connect with external Audio/Video system such like Digital Camera or Game Console. User can connect the external A/V system thru the A/V in jack on front panel.

AV-2

Connect the external signal to the RCA line in jack located at the rear of the unit , then press

button to select AV -2.

TIPS

The below “ No Video Signal ” will show on the TFT as remind if there is no any external AV System input.

Tips

Be sure to connect Parking Brake connection lead. ( please see more details on “ Wiring Diagram.”)

NOTE

If watch moving video from Disc or AV In source but Parking Brake is NOT PROPERLY CONNECTED, the video signal will be blocked by the system and the below display will be show on TFT:

Info

About The Reverse Wire For Back Up Camera System

About the Parking Wire

CAUTION

NOTE

The Video Blocking system under Parking Brake NOT ENGAGED only control this unit's display, This system will not affect the Video Output thru the rear RCA Video Output.

If user connected a back up camera system to this unit, the vehicle is in reverse Gear (Back Up mode), the front in-dash TFT display will automatically switch to Back Up Camera Video signal regardless whatever mode is currently displayed on the front indash TFT.

Tips

Be sure to connect Reverse wire properly. (please see more details on “ Wiring Diagram.”)

E - 22

Page 23

Wallpaper Setting

Setting the Background Screen (Wallpaper)

This unit allows the user to change the background screen on the playback mode. This function is called wallpaper change. User can select the desire image on the below operation to set as wallpaper.

How To Select The Image

Under Setup menu, tap button access into the Image Setting mode, the below TWO location are available for images selection:

My Gallery

There is total 10 factory default images for the user to select as wallpaper.

TIPS

For details operation, please refer to SETUP MENU_MY GALLERY.

My Image

This stores all images capture by user on this unit.

TIPS

For details operation, please refer to SETUP MENU_MY IMAGE.

2. Hold press the CAPTURE button for more

than 3 seconds when the desired scene or image appear on the TFT screen.

3. The confirmation display will appear to

confirm the image is stored in to MY IMAGE.

TIPS

Those captured images will store in the SETUP_MY IMAGE. For details please refer to SETUP MENU_MY IMAGE.

How To Setting The Captured Images As Wallpaper

The captured images can be set as wallpaper on the playback mode.

TIPS

For details setting of wallpaper, please refer to SETUP MENU_MY IMAGE.

NOTE

Do not turn off the unit while storing the image.

Stored image may differ from the original aspect ratio due to compression or elongation.

Capturing Images for Wallpaper

This units allows user during video or images playback, user can capture images and store them (up to 10 images) to set as wallpaper. User also can capture an image from an Auxiliary video device if connected.

How To Capturing Images

1. Start playing the disc, USB stick , SD card or auxiliary video device.

E - 23

Page 24

Bluetooth Operations

User Guide For Bluetooth

1. When user use our Bluetooth HEAD UNIT,

please make sure the mobilephone you use must / does support Bluetooth functions (Headset or Handsfree profiles or both).

2. Before you start to use our Bluetooth HEAD UNIT, please make sure complete pairing with your mobile phone first. Please refer to the user manual, section “PAIRING” for detail “PAIRING” instruction. To ensure the best reception for Pairing or Re-connection, please make sure the Phone Battery is fully charged when making the Pairing or Reconnection

3. Please always try pairing the Mobile Phone with Head unit after a few minutes of the Mobile Phone Switched On to ensure the best pairing result.

4. “BT70” is this unit device model number which is displayed on the mobile phone.

5. To achieve the best performance, please always keep the Mobile Phone within 3 meters of the Head unit.

6. Please always keep a clear path between the Mobile Phone & the Head unit.

7. Never put any metal object or any obstacle between the path of the Mobile Phone & the Head unit.

8. Some mobile phone brands like Sony Ericsson may have "Power Saving Mode" selection when Bluetooth mode is switch on. DO NOT Switches ON Power saving Mode when operating with this Head Unit, as some abnormal communal behavior will happen occasionally if Power Saving Mode is switched on.

9. Before user makes Outgoing call or Incoming calls, make sure the mobile phone's “Bluetooth function” is switched “ON”.

11. If user want to Dis-connect the Head unit with the Mobile Phone, please switch "OFF" Bluetooth connectivity on the Mobile Phone, or go to the system menu, "disconnect" to disconnect the Bluetooth connectivity manually. ( please refer to the user manual, section “dis-connection of the Bluetooth system for details instruction. )

12. Some Mobile Phones can support “IN BAND RING TONE”, such as Nokia. In such case, the Incoming Ringing Tone will be same as the original Ring-tone of the Mobile Phone. But some Mobile Phones like Sony Ericsson do not support this feature. The Ring-tone will be using the standard Ring-tone of the Head unit.

13. When in telephone mode, during talking, it is highly recommended to set the volume to below “35” in order to achieve the best sound quality. As if the volume is too high, it may create unwanted echo inside the car, and this unwanted echo mayfeedback into the microphone.

14. If the Bluetooth related operation is not performing normally, like cannot make pairing, cannot making an outgoing call, the user can try to make a SOFT-RESET of the Bluetooth module by removing / detaching the panel from the main unit and waiting for about 1 min. Then re-attach the panel to the unit & retry the Bluetooth operation again. Or user can RESET the whole unit by pressing the RESET button behind the panel.

NOTE

By pressing the RESET button all the stored memory will resume to factory default.

10. To ensure the best conversation quality / performance, keep talking within 1 meter of the Head Unit.

E - 24

Page 25

Bluetooth Operations

Handsfree Operation

Pairing, Connecting And Deleting With A Bluetooth Device

When connecting Bluetooth devices at the first time with this unit, a mutual registration is required, this is called “Pairing”. This registration (Pairing) is required only at the first time, as this unit and the other devices will recognize each other automatically from the next time.

After the devices are registered (Paired) with this unit. User can select the registered device and connect it, this is called “Connecting”.

TIPS

This unit can Pair up to 8 devices with Handsfree and / or Audio Devices.

If the pairing Bluetooth device has both HFP (Handsfree Profile) and A2DP (Advance Audio Distribution Profile). This unit will automatically pairing these two profiles at the same time.

3. When searching is completed, the detected device name(s) will be displayed in a list.

4. Tap the device name you want to be connected/paired with the selected device in the list.

5. Password input: user can input minimum 1 & up to maximum 4 of any numeric number between 0 to 9, as the password for this unit.

6. Tap button on display to confirm the password input, and the Pairing process should start.

7. “BT70” should appear on the pairing device, user should select & accept pair with “BT70” and then input the same password which was input on this unit previously on above step 6.

NOTE

Please refer to the instruction manual of the Bluetooth device on how to enter into the Bluetooth set up and Bluetooth pairing.

8. If the pairing is successful, the below display will be show on TFT:

Searching available Bluetooth Devices for Pairing “from this unit”.

1. Access into the SETUP MENU, and touch to activate the Pairing procedure.

NOTE

Please see SETUP MENU Operation for more details of how to access into Bluetooth Menu – Pairing mode.

2. Tap to activate the searching

pairing device mode.

NOTE

Please make sure to check the pairing Bluetooth device, make sure the Bluetooth mode is turned ON and the “VISIBILITY” is set to “SHOW”.

Stored image may differ from the original aspect ratio due to compression or elongation.

If the pairing failed, the below display will be show on TFT for 3 seconds:

and the unit will automatically switch back to the previous mode.

NOTE

During Pairing, only the Volume & Mute buttons are functional, all the other function keys are disabled & non-operational during the pairing mode.

E - 25

Page 26

Bluetooth Operations

Pairing The Bluetooth System Between Mobile Phone & The Unit

1. Open your Mobile Phone and switch Bluetooth to on, and search Bluetooth device.

2. “BT70” should appear in the pairinglist on the Mobile Phone. User need to select “BT70” and then input the password “0000”, the below display will be show on TFT:

Tap button to confirmed the

connect.

Disconnecting of the Bluetooth System

User can disconnect the connected Bluetooth device as follows:

1. Access into the SETUP MENU of Bluetooth Menu_Paired (Handfree).

2. Tap button access into the HandFree Device list.

3. Tap button to disconnect

this device, and the below display will be sholw on TFT:

3. If the pairing is successful, the below display will be flashing on the TFT for 3 seconds. And the unit will switch back to the previous mode automatically.

If the pairing failed, the below display will be show on TFT:

Tap button to confirmed the

disconnect.

Deleting

User can delete a paired device if it is no longer needed as follows:

1. Access into the SETUP MENU of Bluetooth Menu_Paired (Handfree).

NOTE

During Pairing, only Power/Mute, Volume Knob are functional, all the other function keys are disabled & non-operational during the pairing mode.

2. Tap button access into the HandFree Device list.

3. Tap button to Delete the

device, and the below display will be sholw on TFT:

E - 26

Page 27

Tap button to confirmed the

selection to delete.

3. If the delete is successful, the below display will be show on the TFT:

INCOMING CALL

Answering An Incoming Call

1. When there is an incoming call, the below display will be show on TFT:

4. To end the conversation, tap button. The unit will switch back to the

previous mode automatically and release the mute of the previous mode at the same time.

NOTE

An Incoming call under stand by mode (Ignition on & Power Off), the system will automatically switch on the head unit.

Rejecting An Incoming Call

User can tap button to reject the incoming call.

NOTE

The audio output of the present mode will be muted and the ringing tones will be heard if an incoming call is not being answered. After tapping the button, the mute of the present mode will be released.

2. If the incomingcall hasno caller I.D. number, the display will show UNKNOW. user can tap the button to answer / accept the call.

NOTE

The audio output of the present mode will be muted and the ringing tone will be heard if an incoming call is not being answered.

3. User can use the Volume Up / Down to

adjust the volume level.

OUTGOING CALL

Making An Outgoing Call

1. User can tap button on display enter into the dial and make an outgoing call.

NOTE

User also can use his/her Mobile Phone to dial and make an outgoing call.

E - 27

Page 28

Bluetooth Operations

2. Once the phone number has been entered completely, tap button to start dialing the call, and the below display will show on the TFT:

3. User can use the Encoder Volume Knob to

adjust the volume level.

4. Tap button on display to end the conversation. The unit will switch back to the previous mode automatically. The mute of the previous mode will be released at the same time.

5. During talking mode, if the Ignition is being

turned off, the unit will keep the conversation even if the ignition is switched off. After the conversation, User can tap

button to switch off the unit.

NOTE

After the tapped button, the present mode will be muted at the same time, user can press the

button to release the Mute.

When making an outgoing call, it's not possible to CALL TRANSFER if the call is not being answered yet. It's only possible to Transfer the call to Mobile Phone after the call is being answered.

Depending on different type of Mobile

Phone, the time need for activating

the CALL TRANSFER mode is

different. Example Nokia Mobile

Phone usually takes 3-5 seconds after

tapping button for audio

transfer back or forth from Unit to

Mobile Phone.

CALL TRANSFER

To Audio Transfer From Head Unit Back To The Mobile Phone

During the talking mode, user can tap the

button to transfer the audio from

the unit back to the Mobile Phone for privacy

reason. The below display will be show on TFT

for 3 seconds:

AUTO ANSWER

Auto Answer Mode

User can set this unitto automaticallyanswer all

the incoming calls, once this function is set to

on, user do not need to tap the button to answer / accept any incoming call.

NOTE

Please refer to the SETUP MENU Operation for more details of how to access into and operates the SETUP MENU of BLUETOOTH

_Auto Answer.

E - 28

Page 29

Bluetooth Operations

Bluetooth Audio Operation

Bluetooth Audio Streaming A2DP (Advanced Audio Distribution Profile)

User can listen to music files on an audio device on this unit if the audio device supports A2DP (Advanced Audio Distribution Profile) of Bluetooth Technology. Please read the below instruction before operating the Bluetooth Audio streaming function on this unit.

Connecting A Bluetooth Audio Device With This Unit

Before using an audio device to play music on this unit, the audio device must be paired with this unit first.

Open your Mobile Phone and switch Bluetooth to ON, and search Bluetooth device.

“BT70” should appear in the pairing list on the Mobile Phone. User need to select“ and then input the password “0000” , the below display will be show on TFT:

BT70”

TIPS

If the audio device has both HFP (Hands Free Profile) and A2DP (Advance Audio Distribution Profile), this unit will automatically pair these two profiles at the same time. For example: if a mobile phone has both HFP & A2DP profile and this mobile phone is already HFP paired with this unit, A2DP audio device pairing is not necessary. Also this paired mobile phone will be added automatically to the list of Paired Device – Audio of this unit.

Listening To Music From An Audio Device In This Unit

1. Connect this unit with the audio device.

NOTE

Make sure the Bluetooth system is connecting with this unit. If the BT icon on the TFT is blinking, it means the Bluetooth is disconnected with this unit. Open your Mobile Phone or Audio device to re-connect Bluetooth again. .

2. Enter into the SOURCE Menu to light up the BT Audio mode, and the

will appears on the TFT.

Tap button to confirmed the

connect.

If the pairing is successful, the below display will be flashing on the TFT for 3 seconds. The unit will switch back to the previous mode automatically.

IMPORTANT

To listen to Bluetooth audio streaming from the audio device, user MUST change the mode to . first. Any other mode of this unit is not able to activate the Bluetooth audio streaming ( A2DP ) function.

NOTE

In Bluetooth Audio Mode, if there is no audio device connected with this unit, the TFT will show

The unit will search for an audio device for 20 seconds. If there is no device found, the screen will display "NO DEVICE”

3. Once in the mode, user can use the audio device to start playback via Bluetooth wireless with this unit.

E - 29

Page 30

Bluetooth Operations

NOTE

When you change to Bluetooth Audio mode, some audio devices will automatically start playback. Some phones may require you to choose 'Media Player' mode on your phone. If the auto playback is not supported on the audio device, please refer to the instruction manual for the audio device on how to operate music playback via Bluetooth wireless technology.

Operating an audio device with this unit AVRCP ( Audio Video Remote Control Profile )

This unit can perform the following operations when the connecting Audio device supports AVRCP (Audio Video Remote Control Profile) only if the Audio device supports AVRCP.

1. Start playing - Every time the user switches to mode, this unit will automatically send a “PLAY” command via AVRCP to the audio device to command the auto start playing song in the audio device.

6. Stop playback - by changing mode into any other mode of this unit.

NOTE

The AVRCP operation may differ depending on the audio device.

Handsfree Phoning While Bluetooth Audio Streaming

If the connecting playback audio device is a mobile phone, all the hands free function is still available under the Bluetooth audio streaming, like the answering incoming call, making an outgoing call, etc.

Disconnecting An Audio Device With This Unit

User can close the Bluetooth Audio connection by disconnecting with the audio device on the Mobile Phone.

NOTE

For more detail and information on disconnecting with the unit, please refer to the DISCONNECTION section.

NOTE

The PLAY command may differ depending on the Audio device. If the Audio device is not able to auto start playing after changing mode into mode, user may need to operate the PLAY mode on the audio device to start the song playback.

2. Track up / down - by pressing the Track up / down buttons on this unit.

3. Pause/Play - by pressing the Pause / Play

button on this unit.

4. Volume up/down - by pressing the volume

up / down on this unit.

5. Audio Mute - by pressing the Mute button

on this unit.

E - 30

Page 31

Specifications

TFT Screen Section

Screen Size: 6.1(Measured Diagonally) Screen Type: TFT Liquid Crystal Display active matrix Resolution: 480 x 234

DVD / CD Section

Compatible Disc/Format Signal to Noise Ratio Dynamic Range Frequency Response Channel Separation

Video Section

Color System Video Output Video Input

Audio Section

Max Output Power Load Impedance (speakers) Digital Output Line out level / load Line out Impedance

See “ Disc Note” for more details description >90dB >9

0dB 20Hz to 20Khz +/-3dB 2 Channel (Stereo) >60dB @1khz

NTSC / PAL Composite 1.0 Vp-p (+/- 0.2) 75 - ohm Composite 1.0 Vp-p (+/- 0.2) 75 - ohm

8 0W x 4 channels 4 ohms 900mV 400mV / 10k ohm load 200 ohm

Auxiliary Input Section

Frequency response Input Maximum Voltage Input Impedance

Radio Section FM

Frequency Range

Usable Sensitivity Stereo Separation S/N Ratio

AM or MW

Frequency Range

Usable Sensitivity S/N Ratio

BLUETOOTH

Power Consumption Output Power Frequency Band Range Standard

General

Operating Voltage Grounding System Fuse: Operating Temperature: Unit Mounting Angle

E - 31

20Hz to 20KHz -3dB 1200 mV

4.7k ohm

87.5-108.0 MHz (50 kHz Space)

87.5-107.9 MHz (200 kHz Space) < 15dB at S/N 30 dB 25 dB at 1KHz 50 dB

522-1620 Khz (9 kHz Space) 530-1720 (10 kHz Space) < 40dB at S/N 20dB 40 dB

200mA

0 dBm (Class II)

2.4GHz ~ 2.4835GHz ISM Band 3 meters (free space) Bluetooth 2.0 specification

DC 11 -14.4V Negative Ground 15-Amp Mini ATM Type

0°Cto50°C

<30°

Page 32

Troubleshooting

Before going through the check list, check wiring connection. If any of the problems persist after check list has been made, consult your nearest service dealer.

Symptom

No power

Disc cannot be loaded or ejected

No sound

Cause

The car ignition is not on.

The fuse is blown.

Presence of CD disc inside the player.

Inserting the disc in reverse direction.

Compact disc is extremely dirty or defective disc.

Temperature inside the car is too high.

Condensation.

Volume is in minimum.

Wiring is not properly connected.

Solution

If the power supply is properly connected to the car accessory terminal, switch the ignition key to “ACC”

Replace the fuse.

Remove the disc in the player, then put a new one.

Insert the compact disc with the label facing upward.

Clean the disc or try to play a new one.

Cool off or until the ambient temperature returns to normal.

Leave the player to off for an hour or so, then try again.

Adjust volume to a desired level.

Check wiring connection.

The operation keys do not work

Sound skips.

The radio does not work. The radio station automatic selection does not work.

ERROR

Disc Error

If at any time in the future you should need to dispose of this product, please noted that: Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your local Authority or retailer for recycling advice. (Waste Electrical and Electronic Equipment Directive).

The built-in microcomputer is not operating properly due to noise.

The installation angle is more than 30 degrees.

The disc is extremely dirt or defective disc.

The antenna cable is not connected.

The signals are too weak.

Mechanism Error

Maybe disc dirty / disc scratched /disc upside down.

Press the RESET button. Front panel is not properly fixed into its place

Adjust the installation angle to less than 30 degrees.

Clean the compact disc. Then try to play a new one.

Insert the antenna cable firmly.

Select a station manually.

Press the eject button to correct the problem. If the error code does not disappear, consult your nearest service dealer.

Replace the disc.

E -32