Page 1
Page 2
10
DC 12V
9W
12.1 TFT-LCD
4:3 Wide
2400*600
2 A/V RCAInputs
(L)15.1 (W)13.4 (H)3.3inch
DC 12V
3W
Right 2.8MHz Left 2.3MHz
Active Matrix TFT
Power Requirements
Power Consumption
Screen Size
Screen Format
Resolution Pixel
A/V Inputs
Dimensions
IR Power Requirements
IR Power Consumption
IR Transmitter Frequency
LCD Panel Type
Compatible video standard
NTSC/PALauto select
SPECIFICATIONS
Note :This equipment has been tested and found to comply with the limits for
a ClassA digitaldevice, pursuant to part 15 of the FCC Rules. These limits
are designedto provide reasonableprotection against harmfulinterference
when theequipment is operatedin a commercialenvironment.
This equipmentgenerates, uses, andcan radiate radiofrequency energy and,
if notinstalled and usedin accordance withthe instruction manual,may cause
harmful interferenceto radio communications.Operation of thisequipment in
a residentialarea is likelyto cause harmfulinterference in whichcase the user
will berequired to correctthe interference athis own expense.
Page 3
2
CAUTION 4
INSTALLATION 5
NAME AND FUNCTION OF EACH PARTS 6
Unit 6
Remote Control 7
CONNECTIONS 8
HOW TO OPERATION THE MONITOR 9
Releasing The Monitor 9
How To Watch Monitor 9
SPECIFICATIONS 10
Please read this User,s Manual in detail and use the set properly.
9
CONTENTSHOW TO OPERATE THE MONITOR
POWER
POWER
PUSH BUTTON
Releasing the Monitor
How to watch the monitor
UNIT
REMOTE CONTROLLER
1. Connect the monitor to the external devices.
2. Press the POWER button on either the remote control or the unit once to turn
the power on.
Press the same POWER button to turn the power off.
3. Turn on the external devices and view.
Push the open button (located on the front edge of the screen housing)
and lower the monitor to the desired angle. You can also adjust the
swivel angle.
Page 4
3
8
CONNECTIONS
CAUTION
Please read and observe all warnings and instructions in this owner s manual
and those marked on the unit. Retain this booklet for future reference.
There are two kinds of alarm symbols as follows:
WARNING
WARNING
CAUTION
The lighteningflash with arrowhead symbol within an equilateral
triangle isintended to alert the user to the presence of
dangerous voltage within the product s enclosure that may be
of sufficientmagnitude to constitute a risk of electric shock to
people.
The exclamationpoint within anequilateral triangle isintended
to alertthe user tothe presence ofimportant operating and
maintenance (servicing)instructions in theliterature accompanying
the product.
Installation ofall TV monitors
must beout of thedriver s
field ofsight.
Do nottry and servicethese
products yourself,Seek only
a qualifiedservice center or
factory servicecenter.
Be carefulnot to dropor
apply underpressure to the
front panelof your video
monitor. If the screen cracks
due tomisuse, your warranty
will bevoid!
Do notmount the productwhere
it willobstruct the deploymentof
the airbagor in anarea where it
would affectthe vehicular control.
Also becareful to avoidmounting
the productwhere it canbecome
hazardous duringsudden stops or
in theevent of anaccident.
Be carefulnot to overloadyour
cigarette lighterplug by adding
more thanone device ata time.
Use extracaution with anyliquids
in yourcar. If you or your child
Spills anyliquid on theseproducts,
pull yourvehicle to theroadside
and turnthe key offto disconnect
or wipethe products witha towel. Donot
operate theequipment until allliquids have
either evaporatedor you havehad the monitor
inspected ata service centerby a qualified
technician, Severeharm or dangercan
Occur.
Use onlya damp clothto clean
the screenand use onlypurified
water onthe cloth. Wringout all
excess waterprior to wipingthe
screen. Donot use anycleaners
or chemicalsto clean thescreen.
In mostcases a drycloth will do!
P
O
W
E
R
A
V
MEN
U
,
,
CAMCORDER
GAME
White AUDIO(L)
Red AUDIO(R)
Yellow VIDEO
CAMCORDER
GAME
White AUDIO(L)
Red AUDIO(R)
Yellow VIDEO
AV Input
(AV 2)
(AV 1)
AV Input
YELLOW
Switched 12Volts
BLACK
RED
Constant 12Volts
Ground
Car domelamp
WHITE
Positive Negative
Trigger Door Trigger Door
Switch Switch
Dome LightTrigger
Page 5
7
NAME AND FUNCTION OF EACH PART
CAUTION
4
Quality installationsare best
performed byqualified and
certifled installers.
Don ttouch the unitif there is
a flashof lightning. Itmay
receive anelectric shock.
Do notcover heater ductsor vents.
This maycause a fireor an electric
shock.
Watching the monitor for an
extended periodof time
with theengine turned off
may depletethe vehicle s
battery.
This productis designed for
operation witha 12 Volt DC,
negative groundvehicle. It
is notsuitable for operation
under otherconditions or
voltages.
1. The operating temperature of this product is limited to 14 F~140 F
(-10 C~60 C).
Your vehicle can reach temperatures up to 100 C in the summertime.
2. When your vehicle is extremely hot or cold you must allow time for your air
conditioner or heater to cool or heat the vehicle and for operating temperatures
to return to normal operating ranges. Your monitor will return to its normal
functions when these operating ranges are achieved.
3. Optimum picture quality is achieved when you are directly in front of the monitor
(+/-45 degrees).
CAUTION
Check Point
Dome LightButton
POWER Button
AV Select Button
MENU Button
+/- Buttons
Dome LightButton
Interface Switch Function
Power Power ON/OFF
AV Signal Select
Menu Press this button for OSD menu.
And select menu option
-
+
Increase current option value.
Decrease current option value.
POWER KEY
AV1 /AV2 K EY
+KEY
-KEY
MENU KEY
Page 6
5
6
INSTALLATION NAME AND FUNCTION OF EACH PART
Unit
Dome light
Monitor
(Front)
Monitor
(Rear)
AUX Input Jack
R
L
AUDIO
VIDEO
AV2INPUTS
1. Open the package and check that these items are presents.
INSTALLATION PLATE
UNIT
SCREW A SCREW B
2. Connect the external compoments to the RCA cable or AV output.
(Refer to the connection diagram on page 8)
3.Match the position of installation bracket and
installation plate with screw A.
4. Tighten the unit with the supplied
screw B.
Infrared Transmitter
Loading...