Boss Audio Systems 822UA User Manual

LOCATION OF CONTROLS

POWER BUTTON

TUNING / SEEK / CD TRACK UP / DOWN BUTTON

BAND / LOUDNESS / MP3 ENTER BUTTON

VOLUME UP / DOWN BUTTONS

CD PAUSE BUTTON

CD SHUFFLE BUTTON

LOCAL/DX BUTTON

FM STEREO / MONO BUTTON

DSP BUTTON

MODE BUTTON

DISPLAY/ ID3 TAG INFORMATION BUTTON

FUNCTION SELECT BUTTON

CD SCAN BUTTON REPEAT BUTTON PRESET MEMORY BUTTONS

DIRECTORY UP/DOWN BUTTONS SCAN BUTTON

REMOTE CONTROL

HANDLING COMPACT DISCS

MOISTURE CONDENSATION

On a rainy day or in a very damp area, moisture may condense on the lenses inside the unit. Should this occur, the unit will not operate properly. In such a case, remove the disc and wait for about an hour until the moisture has evaporated.

NOTES ON CDs

A dirty or defective disc may cause sound

dropouts while playing. To enjoy optimum sound, handle the disc as follows. Handle the disc by its edge. To keep the disc clean, do not touch the surface (P.1).

P. 1

Do not stick paper or tape on the disc (P.2).

P. 2

Do not expose the discs to direct sunlight or

heat sources such as hot air-ducts, or leave them in a car parked in direct sunlight where there can be a considerable rise in temperature inside the car (P.3).

Before playing, clean the discs with an

optional cleaning cloth. Wipe each disc from the centre out (P.4).

P. 3

NOTES ON DISCS

If you use the discs explained below, the sticky residue can cause the CD to stop spinning and may cause malfunction or ruin your discs.

Do not use second-hand or rental CDs that have a sticky residue on the surface (for example, from peeled-off stickers or from ink, or glue leaking from under the stickers).

There are paste residue. Ink is sticky (P.5).

P. 5

Do not use rental CDs with old labels that are beginning to peel off.

Stickers that are beginning to peel away, leaving a sticky residue (P.6).

P. 6

Do not use your CDs with labels or stickers attached.

Labels are attached (P.7).

P. 7

Do Not Use Special Shape CDs

Be sure to use round shape CDs only for this unit and do not use any special shape CDs. Use of special shape CDs may cause the unit to malfunction.(P.8).

****

*******

**************

*******

P. 4

Do not use solvents such as benzine,

thinner,commercially available cleaners, or antistatic spray intended for analog discs.

P. 8

Be sure to use CDs with disc mark Only for this unit.

CD-Rs and CD-RWs which have not undergone finalization processing cannot be played. (For more information on finalization processing, refer to the manual for your CD-R/CD-RW writing software or CD-R/CD-RW recorder.) Additionally, depending on the recording status, it may prove impossible to play certain CDs record on CD-R or CD-RW.

E - 2

INSTALLATION

Before finally installing the unit, connect the wiring temporarily and make sure it is all connected up properly and the unit and system work properly. Use only the parts included with the unit to ensure proper installation. The use of unauthorized parts can cause malfunctions. Consult with your nearest dealer if installation requires the drilling of holes or other modifications of the vehicle. Install the unit where it does not get in the driver's way and cannot injure the passenger if there is a sudden stop, like an emergency stop. If installation angle exceeds 30 degree from horizontal, the unit might not give its optimum performance.

Avoid installing the unit where it would be subject to high temperature, such as from direct sunlight, or from hot air, from heater, or where it would be subject to dust dirt or excessive vibration. Be sure to remove the front panel before installing the unit.

DIN FRONT/REAR-MOUNT

This unit can be property installed either from Front (conventional DIN Front-mount) or Rear(DIN Rear-mount installation, utilizing threaded screw holes at the sides of the unit chassis). For details, refer to the following illustrated installation methods A and B.

DIN FRONT-MOUNT (Method A) Installation the unit

178

100

1. Dashboard

2. Holder After inserting the half sleeve into the dashboard,

select the appropriate tab according to the thickness of the dashboard material and bend them inwards to secure the holder in place.

3. Screw

ANTENNA JACK

REAR LINE OUT LEFT REAR LINE OUT RIGHT

FRONT LINE OUT RIGHT

FRONT LINE OUT LEFT

1. Dashboard

2. Nut (5mm)

3. Spring washer

4. Screw (5x15mm)

5. Screw

6. Support Strap

Be sure to use the support strap to secure the

back of the unit in place. The strap can be bent by hand to the desired angle.

7. Plain washer

Trim Plate Installation: Push the trim plate against the chassis until it is fitted. You must do this before you install the front panel, otherwise it can't be attached.

E - 3

+ 10 hidden pages