Boss Audio Systems 820UA User Manual

24
10 R - 03 0500
1. BUTTONS LOCATION AND FUNCTIONS
5
3
13
2. Mute Button
3. CD Eject Button
4. Power Button
5. Display Button / ID3Information Button
6. Local / Distant Button
7. Preset Memory Buttons
8. Menu Button
9. Scan Button
10. Volume Knob
11. MP3Menu Button & Automatically Store/ Preset Scan Button
12. Band/LoudnessButton / MP3 Enter Button
13. TuningUp/Down & Track Up / Down Buttons
14. RemoteControl Receiver
15. SourceButton
16. AuxIn Jack
17. USBSlot
1. Entriegel-Taste Bedienteil
2. Stumm-Taste
3. CD-Auswurftaste
4. Einschalt-Taste
5. Display-/ ID3-Taste
6. Local/ Distant-Taste
7. Senderspeichertasten
8. SuchlaufTaste
9. Scan-Taste
10. Lautstärkenregler
11. AMSTaste
12. Frequenzband-Taste/ MP3Eingabe-Taste
13. Titel AUF /AB - Taste
14. Fernbedienungs-Taste
15. Source
16. Front-Audio-Anschluss
17.
Ta st eUSB -
5
1.Teclapara remover opainelfrontal
2.TeclaMute
3.Teclapara ejetar odisco
4.TeclaLigar/desligar
5.TeclaDisplay / informaçãoMP3-iD3
6.TeclaLocal/Distante
7.Teclasde memória deestações
8.TeclaMenu
9.TeclaScan
10.Controledevolume
11.Memorizaçãoautomática(As) / PresetScan(Ps)
12.TeclaBanda / Loudness/MP3Enter
13.Teclasde sintonização deestações/
demúsica
14.Sensordocontrole remoto
15.TeclaSource
16.EntradaAuxiliar
17.
EntradaUSB
1. Extraccióndel panel frontal
2. Silenciamientorápido
3. Aperturadel panel motorizado y expulsióndel disco
4. Encendido/Apagado
5. Seleccióninformación Display/ID3 TAGmuestra
6. BotónDistancia/Local
7. Botonesde estaciones memorizadas
8. Menúdel Sistema
9. BotónDe Búsqueda
10. BotónDe Volumen
11. MemorizaciónAutomática de emisoras / selecciónde memorias
12. SelectorBandas / Bajos/MP3
13. Botónde selección deemisoras &banda de música
14. Receptorde control remoto
15. Selecciónmodos Radio/CD/Entrada auxiliar&Botón De Sub-W
16. Entradade auxiliar
17.
Entrada deUSB
mudançadefaixas
1. BoutonDeDéclenchementDuPanneau
2. BoutonD'assourdissement
3. BoutonÉjectionD'unCd
4. BoutonD'alimentation
5. BoutonD'écran/AffichageD'information Sur Les Disques MP3
6. BoutonLocal/distant
7. BoutonsDesStationsPréréglées (m1 ~m6)
8. BoutonDeMenu
9. BoutonDuScanner
10.BoutonDe Volume
11.BoutonDe Stockage Des Stations Dans La Mémoire
12.BoutonDe Bande /Entrée De MP3
13.BoutonDe Recherche Des Stations/pistes : En Avant / En Arrière
14.RécepteurDe La Commande À Distance
15.BoutonDe Régime/Subwoofer
16.AuxA Jack
17.
USBSlot
1. Tasto RilascioFrontalino
2. Tasto Mute
3. Tasto Eject
4. Tasto Power
5. Tasto Display/ID3(informazioni)
6. BottoneDistante Locale
7. Tasti StazioniMemorie Preimpostate
8. Tasto Menu
9. Tasto Scan
10. Tasto Volume
11. Tasto AS/PS
12. Tasto Banda/Forte & Enter MP3
13. Tasto sintonizzazionesu/gui & traccia su/gui
14. Destinatariodi controllo remoto
15. Tasto Mode/Subwoofer
16.EntradaAux
17.
Entrada USB
2. HANDLING COMPACT DISCS
MOISTURE CONDENSATION
On a rainy day or in a very damp area, moisture may condense on the lenses inside the unit. Should this occur, the unit will not operate properly. In such a case, remove the disc and wait for about an hour untilthe moisture has evaporated.
NOTES ON CDs
1.
A dirty or defective disc may cause sound dropouts while playing. To enjoy optimum sound, handle the disc as follows. Handle the disc by its edge. To keep the disc clean, do not touch the surface (P.1).
P. 1
Do notstick paper or tape onthe disc (P.2).
2.
P. 2
Do not expose the discs to direct sunlight or
3.
heat sources such as hot air-ducts, or leave them in a car parked in direct sunlight where there can be a considerable rise in temperature inside the car (P.3).
P. 3
Before playing, clean the discs with an
4.
optional cleaning cloth. Wipe each disc from the centre out (P.4).
NOTES ON DISCS
If you use the discs explained below, the sticky residue can cause the CD to stop spinning and may cause malfunction or ruin your discs.
Do not use second-hand or rental CDs that have a sticky residue on the surface (for example, from peeled-off stickers or from ink, or glue leaking from under the stickers).
There are paste residue. Ink is sticky (P.5).
P. 5
*******
*******
Do not use rental CDs with old labels that are beginning to peel off.
Stickers that are beginning to peel away, leaving a sticky residue (P.6).
P. 6
Do not use your CDs with labels or stickers attached.
Labels are attached (P.7).
P. 7
Do Not Use Special Shape CDs
Be sure to use round shape CDs only for this unit and do not use any special shape CDs. Use of special shape CDs may cause the unit to malfunction.(P.8).
****
*******
*******
**************
*******
*******
*******
*******
*******
*******
*******
*******
P. 4
Do not use solvents such as benzine,
5.
thinner,commercially available cleaners, or antistatic spray intended for analog discs.
P. 8
Be sure to use CDs with disc mark CD-Rs and CD-RWs which have not
undergone finalization processing cannot be played. (For more information on finalization processing, refer to the manual for your CD-R/CD-RW writing software or CD-R/CD-RW recorder.) Additionally, depending on the recording status, it may prove impossible to play certain CDs record on CD-R or CD-RW.
E - 1
3. INSTALLATION
Before finally installing the unit, connect the wiring temporarily and make sure it is all connected up properly and the unit and system work properly.
Use only the parts included with the unit to ensure proper installation. The use of unauthorized parts can cause malfunctions.
Consult with your nearest dealer if installation requires the drilling of holes or other modifications of the vehicle.
Install the unit where it does not get in the driver's way and cannot injure the passenger if there is a sudden stop, like an emergency stop.
If installation angle exceeds 30° from horizontal, the unit might not give its optimum performance.
Avoid installing the unit where it would be subject to high temperature, such as from direct sunlight, or from hot air, from heater, or where it would be subject to dust dirt or excessive vibration.
Be sure to remove the front panel before installing the unit.
DIN FRONT/REAR-MOUNT
This unit can be property installed either from “Front” (conventional DIN Front-mount) or “Rear”(DIN Rear-mount installation, utilizing threaded screw holes at the sides of the unit chassis). For details, refer to the following illustrated installation methods A and B.
- DIN FRONT-MOUNT (Method A) Installation the unit
1
2
182
53
4
3
30°
1. Dashboard
2. Half Sleeve After inserting the half sleeve into the dashboard, select the appropriate tab according to the thickness of the dashboard material and bend them inwards to secure the holder in place.
3. Screw
4. Remove the two screws that fix the CD
deck mechanism player before mounting the unit.
1
6
7
4
2
5
3
1. Dashboard
2. Nut (5mm)
3. Spring washer
4. Screw (4x12mm)
5. Screw
6. Support Strap Be sure to use the support strap to
secure the back of the unit in place. The strap can be bent by hand to the desired angle.
7. Plain washer
E - 2
Removing the unit
a
a. Frame b. Insert fingers into the groove in the
front of frame and pull out to remove the frame. (When re-attaching the frame, point the side with a groove
b
c
down wards and attach it.)
c. Insert the levers supplied with the
unit into the grooves at both sides of the unit as shown in figure until they click. Pulling the levers makes it possible to remove the unit from the dashboard.
- Trim Plate Installation:
Before attaching the trim plate, the side with a "Bottom" Label stuck should be at down side (as shown on diagram). Push the trim plate against the main panel until it is fitted.
- DIN REAR-MOUNT (METHOD B)
Installation using the screw holes on the sides of the unit. Fastening the unit to the factory radio mounting bracket.
1. Select a position where the screw holes of the bracket and the screw holes of the main unit become aligned (are fitted) and tighten the screws at 2 places on each side.
2
2. Screw
3. Factory radio mounting bracket.
4
5
3
4. Dashboard or Console
5. Hook (Remove this part)
Note: The mounting box, outer trim ring, and half-sleeve are not used for method
2
B installation.
5
M O
T OT B
O
TT M
O
B
- PANEL OPEN / CLOSE OPERATION
1
T E S
E R
2
1. Press Open button
2. The CD slot will be accessible.
3. After CD is loaded or unloaded return the panel to its original position.
Note: Before inserting or ejecting disc, press the Release button to flip down the faceplate.
NCID
Open button
E - 3
4. DETACHABLE CONTROL PANEL(D.C.P)
Removing The Detachable Front Panel
1.
Open button
To remove the front panel:
1. Press the Panel Open Button.
2. After flipping down the front panel, push it rightwards ( ), then draw the left of the front panel outwards ( ).
Step 2
2.
Step 1
Step 2
Step 1
Attaching The Detachable Front Panel
Step 2Step 1
1. To attach the front panel back to the unit chassis, firstly join the left guide block hole to the left cylinder ( ), then join the right guide block hole and the right cylinder ( ).
Step 2
Step 1
2. Press the centre of the front panel until a “ click” sound is heard.
CAUTION
The D.C.P can easily be damaged by shocks. After removing it, place it in a protective case and be careful not to drop it or subject it to strong shocks.
When the release button is pressed and the D.C.P is unlocked, the car's vibrations may cause it to fall. To prevent damage to the D.C.P, always store it in a protective case after detaching it.
The rear connector that connects the main unit and the D.C.P is an extremely important part. Be careful not to damage it by pressing on it with fingernails, pens, screwdrivers, etc.
Note:
If the D.C.P is dirty, wipe off the dirt with soft, dry cloth only. And use a cotton swab soaked in isopropyl alcohol to clean the socket on
Socket
the back of the D.C.P.
UP SH
E - 4
+ 12 hidden pages