Boss Audio Systems 814CA User Manual

Page 1
Page 2
Page 3
1
2
3
4
5
6
7
8
9
10
11
12
13
NO.
14
15
16
Main Set
Front Panel
Install Bracket A
Install Bracket B-Left Install Bracket B-Right
Spring Washer
Plate Washer
Screw M5
Screw M5X8 BHW
Screw ST5X20 BAW Holder Strip 195mm
User Manual Warranty Card
DESCRIPTION
QTY
1
2
1
1
5
6
1
4
1
1
1
1
1
1
1
17
Remote Control
1
Connector and Lines
1
LIST OF THE PRODUCT
Page 4
Yellow wire not connected or incorrect voltage. Red wire not connected or incorrect voltage.
Black wire not connected
Fuse blown
Speaker wires not connected
One or more speaker wires touching each other or touching chassis ground
Yellow or red wire touching chassis ground
Speaker wires touching chassis ground
Incorrect fuse rating
Unit is not mounted correctly or back strap is not secure
Physical defect in media (CD / MP3/CD-R / CD-RW)
Mechanism error
Servo error or disc is in upside down
Unit will not turn on (no power)
Unit has power (but no sound)
Unit blows fuses
Excessive skipping
ERROR1 appears on display
ERROR2 appears on display
Check connections for proper voltage(11-14VDC)
Check connection to ground
Replace fuse
Check connections at speakers
Insulate all bare speaker wires from each other and chassis ground
Check for pinched wire
Check for pinched wire
Use fuse with correct rating
Check mounting sleeve and back strap support
Check media for scratches
Press eject or RESET
Press eject or RESET
Problem Cause Action
13
TROUBLESHOOTINGCONTENTS
1
INSTALLATION
2
WIRING INSTRUCTION
3
CONTROL LOCATIONS
4
12
10~11
SPECIFICATIONS
6
MP3 PLAYER OPERATION
WIRING DIAGRAM
GETTING STARTED
13
TROUBLESHOOTING
7~9
BUTTON FUNCTION
REMOTE CONTROL BUTTON LOCATIONS
5
Page 5
12 1
INSTALLATION
The installation described in this manual assumes that you have a typical car. If your specific car requires any adjustments or modifications, consult your nearest Boss Audio car audio dealer.
PRECAUTIONS This unit is designed for negative - ground,
12-V DC operation only. Before starting installation, make sure the ignition switch is set to OFF and disconnect the ground terminal of the car battery to avoid short­ circuiting. Install the unit where it will not injure the operation of the vehicle. Install the unit where it will not injure the passenger if where is a sudden stop, like an emergency stop. Avoid installing the unit where it would be subject to high temperatures caused by direct sunlight or hot air from the heater, or where it would be subject to dust, dirt or excessive vibration. Use only the supplied mounding hardware for a safe and secure installation.
REINSTALLATIONS
If there is installation hardware for another receiver already in the dashboard, it must be removed. Before installing the unit in the dash­board, Remove the trim plate from the unit. Then, please remove the screws ( ) on the top of unit.
FRONT PANEL INSTALLATION
Store the detachable in its protective case for safe keeping. To drop/take away/install and recover front panel, see the picture.
Mounting-angle adjustment
The mounting angle should be 30 degrees or less from horizontal.
Caution on installation without using the sleeve
Be sure to use the screws ( ) attach the mounting brackets. (Not supplied).
BASIC INSTALLATION
Note that the installation show is a typical example. For some car types you may need to make adjustments or modification to make adjustments or modification to install the unit. If your car is of such type, consult you nearest Boss Audio car audio dealer.
SUPPLIED MOUNTING HARDWARE FOR INSTALLATION
4a3
1 2
A
B
C
Frequency Range:530KHz-1710KHz
AM TUNER SECTION
Wow&Flutter:0.1% S/N Ratio:52dB Separation:45dB Frequency Response:50Hz - 15KHz
TAPE SECTION
Frequency Range:87.5MHZ-107.9MHz Usable sensitivity:3uV. I. F. Frequency :10.7MHz
FM TUNER SECTION
Power Supply: DC 13.8 Volts. Negative Ground Current consumption:15A MAX Maximum Output Power:4X80W
GENERAL
SPECIFICATIONS
CD SECTION
System: Compact disc audio system Signal Format: Sampling Frequency 44.1KHz No of quantization bits 1bit
Frequency:20-100Hz<5dB/10K-20KHz<5dB
S/N Ratio:70dB(1KHz)(IEC-A net work)
Number of channels:4 STEREO
RCA line output: 450-1500 mv
RCA
DETACHABLE
FACEPLATE
INSTALL BRACKET
CONSOLE
1
2
4
3
a
B
A
B
C
Page 6
Root Folder Navigate
Press three times to navigate from the root folder. The root folder name is briefly displayed, after which the first track or subfolder name is displayed.
AS/PS
Step4
Press to select the desired track within the folder.
BAND/LOUDNESS
Current Folder Navigate
Press four times to navigate the current folder. The current folder name is displayed. After the current folder name is displayed, the currently playing track name is displayed.
AS/PS
Step4
Press to select the desired track within the folder.
BAND/LOUDNESS
2
Speakers Connection
This unit can be wired up to 4 speakers. Make sure that you check all connections before powering up this unit.
Caution:
Do not short speaker wires to chassis ground . It will cause the unit to be damaged.
Ground Connection
Connect Black Wire to Ground terminal.
Power Connection
First connect the Yellow Wire (w/15Amp fuse block) directly to +12v constant power. Then connect Red Wire(w/1 Amp fuse block) to ignition output.
Antenna Connection
Insert coaxial connector to antenna socket.
Caution:
If a fuse is blown, only replace it with one of the same rating.
Other wise may cause severe damage . Repeated blown fuse indicates potential problem(s) exists. A thorough inspection is recommended.
WIRING INSTRUCTION
11
MP3 PLAYER OPERATION
Step2
If a subfolder is selected, the icon will illuminate. Press " " (or turn rotary encoder to the down) first, to preview the desired track or subfolder. NOTE: " " must be pressed first (or turn the rotary encoder encoder to the down) to continue navigating.
FF
Step3
Press BAND/LOUDNESS to select the desired track or subfolder. If a subfolder is selected, two "\\" will illuminate. Press first, then " " (or turn the rotary encoder to the down) to begin navigating the selected subfolder. NOTE: " " must be pressed first (or turn the rotary encoder to the down) to navigate within the subfolder.
BAND/LOUDNESS
Step3
Press to select the desired track or subfolder. If a subfolder is selected, two "\\" will illuminate in the LCD. Press AS/PS first, then " " (or turn the rotary encoder to the down) to begin navigating the selected subfolder. NOTE: " " must be pressed first (or turn the rotary encoder to the down) to navigate within the subfolder.
BAND/LOUDNESS
Step2
If a subfolder is selected, the icon will illuminate. Press " " (or turn the rotary encoder to the down) first, to preview the desired track or subfolder. NOTE: " " must be pressed first (or turn the rotary encoder to the down) to continue navigating.
FF
Page 7
Step2
Press BAND/LOUDNESS to confirm the selected track number or, wait for the input cycle to time out (approximately 4 seconds).
Alphanumeric Track or Folder Search
Press two times, an " * " will flash in the display. Use the buttons in the table on page 7 (16 keystroke maximum input) or the rotary encoder or enter the desired alphanumeric search characters. Press AUDIO for character shift.
AS/PS
Step2
Press BAND/LOUDNESS to initiate the selected alphanumeric search.
Step5
Press to select the desired track within the folder.
BAND/LOUDNESS
MP3 MODEL
The following keys are assigned as MP3 disc plays. Key assigned in searching mode.
Remark:
1. M5 and M6 is assigned Searching file or directory.
AS/PS MODE SELECT
M3 G,H,I,3
SCAN S,T,U,7
SEL CHAR,SHIFT
BAND ENTER
M4 J,K,L,4
T-DOWN V,W,X,8
VOL UP/DOWN CHAR,SEL(A,B~8,9,0)
M1 A,B,C,1
M5 M,N,O,5
T-UP Y,Z,SPACE,9
M2 D,E,F,2
M6 P,Q,R,6
Direct Numeric Track Select
Press one time. "MP3 T*" will flash in the display. Use the buttons in the above table (3 keystroke maximum input), or the rotary encoder to enter the desired track number.
AS/PS
MP3 Direct Select Search and Navigate Modes
Press AS/PS to select between the following MP3 Modes: Direct Numeric Track Select Alphanumeric Track or Folder Search Root Folder Navigate Current Folder Navigate
Step4
Press BAND/LOUDNESS to select the desired track or folder. If a folder is selected, two "\\" will illuminate.
Press first, then " " (or turn the rotary encoder to the down) to begin searching the selected folder. NOTE: " " must be pressed first (or turn the rotary encoder to the down) to search within the folder.
BAND/LOUDNESS
3
WIRING DIAGRAM
b
a
c
B C
A
B
C
D
d
- -
CONNECTIONS
PRECAUTIONS
PRECAUTION ON MAKING CONNECTIONS
Before connecting, make sure that the ignition switch is set to OFF. And remove the ground terminal of the battery to protect the unit and your car from damage.
One or more of the connectors , and may not exist on the model your car. Make the appropriate connection or connections according to the configuration of your unit. See the section "SPECIFICATIONS" of the separate Operating Instructions.
4-SPEAKER CONNECTIONS Note
Speakers with an impedance of 4 to 8 ohms and with adequate power handing capacities. Otherwise, the speakers may be damaged. DO NOT connect the speakers in parallel. DO NOT connect the terminal of the speaker system to the car chassis.
From the car antenna CD Changer(option) RCA Audio output (Front and Rear). AUX IN To the wiring of the vehicle colors of leads Black (ground lead to be connected to
vehicle <metal> boby.) Red (ACC lead to be connected to the terminal from which power is supplied when the ignition switch is set to AC.)
Yellow (Connect to a 12 volt constant wire.) Blue (power antenna lead. If your car has
a power antenna, this wire will turn it on.)
Pink (Power amp remote control)
CONNECTION DIAGRAM
10
MP3 PLAYER OPERATION
b
a
c
F
E
A
B C
A
d
++++
+ ++ +
--
--
--
--
Grey
White
Grey/black
White/black
GROUND
(ACC)
(AUTO ANT)
(12V CONSTANT)
Black
Red
Blue
POWER ANTENNA
IGNITION
Pink (POWER AMP)
CONTROL
RELAY
BATTERY
1A
15A
Yellow
Violet/Black
Green/Black
Violet
Green
++
++
LL
RR
+ ++ +
++++
--------
----
++
++
LL
RR
++
++
------
--
++
++
LL
RR
++
++
--
--
--
--
++
++
LL
RR
++
++
------
--
D
F
E
Step3
Press " "(or turn the rotary encoder to the down), first to preview the search results. If the search returns a folder, the icon will illuminate. NOTE: " " must be pressed first (or turn the rotary encoder to the down) to continue the search.
FF
DISPLAY _,-,+,0
Caution Make the connection correctly, as illustrated in the connection diagram. Do not connect the negative cord of each speaker wire to a common point. When replacing the fuse. Be sure to use a fuse of the same rated amperage. Use of a fuse of a higher rating may cause serious damage to the unit.
F
Page 8
1
DISPLAY
2
3
4
5
AS/PS
6
7
MUTE
8
9
10
11
12
13
14
15
17
16
18
M5/D-DOWN
M6/D-UP
M3/REPEAT
M2/INTRO
DISC SLOT BUTTON
RELEASE
T-UP/DOWN
VOL-UP/VOL-DOWN
SELECT CONTROL BUTTON
19
Superior anti-shock performance (CD-45'S MP3-100'S) Superior disc reading ability: Able to read CD/MP3 Superior ECC(error correction code) capability Color LCD display(black mask)
LCD WINDOW
EJECT
POWER
AUX IN
M4/SHUFFLE
20
OPEN
21
BAND/LOUDNESS
MODE
M1/PAUSE
(REMOTE CONTROL )
(REMOTE CONTROL )
(REMOTE CONTROL )
(REMOTE CONTROL )
(REMOTE CONTROL )
(REMOTE CONTROL )
(REMOTE CONTROL )
(REMOTE CONTROL )
(REMOTE CONTROL )
(REMOTE CONTROL )
(REMOTE CONTROL )
(REMOTE CONTROL )
(REMOTE CONTROL )
(REMOTE CONTROL )
(REMOTE CONTROL )
4
1
5
3
18
11
12
8
9
13
14
6
10
2
17
4
CONTROL LOCATIONS
1
2
3
4
5 6
7
8
9
10
1112
13
14
15
17 16
19
20
21
18
MODEMODE
CD FUNCTION
1.CDP MODE As lift indication, pause, intro, repeat, shuffle of CDP is selected.
2.CDP MP3 mode Pause function of CDP is selected by M1(PAUSE) key. When pressed M2~4 short, INTRO, REPEAT, SHUFFLE function in whole disc is selected.
BUTTON FUNCTION
Press the OPEN to allow the front panel to fold down.
OPEN
When pressed short, it is activated as "CLOCK" key. Clock is displayed for few seconds. When pressed long with displaying CLOCK, "CLOCK ADJUST" mode is activated for few second. During clock adjust mode, hour is adjusted by "T- UP" key and minute by "T-DN" key.
DISPLAY
9
BASS
1.Press SELECT button twice display shows BAS.
2.To adjust BAS level, the VOL up or down.
TREBLE
1.Press button three, display shows TRE.
2.To adjust TRE level,
SELECT
the VOL up or down.
BALANCE
1.Press button four times, display shows BAL.
2.To adjust BAL level,
SELECT
the VOL up or down.
FADER
1.Press button five times, display shows FAD.
2.To adjust FAD level,
SELECT
the VOL up or down.
Press SELECT button,VOLUME MODE is switched on: VOLUME/BASS/TREBLE/BALANCE/FADER
SELECT/ VOL UP/ VOL DOWN
VOLUME
1.Press SELECT button once display shows VOL.
2.To adjust VOL level, the VOL up or down.
Page 9
5
8
BUTTON FUNCTION
MUTE
This key serves to switch the "muted" state on/off. The releasing mode of the mute state is when any key is pressed again.
M1(PAUSE) M2(INTRO) M3(REPEAT) M4(SHUFFLE) M5(D-DOWN) M6(D-UP)
1)RADIO MODE. M1~M6
-PRESET MEMORY is saved when key is pressed for longer than 1 secretary.
2)CD/MP3 PLAY MODE
PLAY/PAUSE-PLAY/PAUSE is activated. During a PAUSE, DISC INDICATOR flashes. TOP -First song will play when Top key is pressed for longer than 0.5sec during play.
INTRO
-INTRO ON/OFF is activated. During INTRO ON, INT indicator comes on and begins playing the first 10sec of each song, until the last song is played, It begins playing the entire track from where INT started.
REPEAT
-CD PLAY mode: REPEAT ON/OFF is activated. When REPEAT ON, RPT INDICATOR comes on and repeats the existing track.
SHUFFLE
-This function shall cause to immediately stop playing the current track and jump to be played in a random order commencing.
D-UP/D-DOWN
-MP3 MODE: 10 TRACK UP/DOWN is activated. When the total track is 10 or less, KEY is inactivated.
-PRESET MEMORY is loaded when key is pressed for less than 1 second.
REMOTE CONTROL BUTTON LOCATIONS
Press RELEASE button to allow the front panel to detachable.RELEASE
When short pressing BAND/LOUNDESS the FM/AM band is toggled OF CHANGER. Cyclically through the tuning bands: FM1->FM2->FM3->AM The loudness mode in E.VR is activated by pressing this key for more than 1 secretary. LOUD of individual sag is turned on when LOUD mode is engaged. LOUD of individual sag is turned off when LOUD mode is released.
BAND/ LOUDNESS
Press the OPEN to allow the front panel to fold down.
Page 10
6
7
BUTTON FUNCTION
1.Press the POWER button to turn the unit on.
2.Insert the CD, and then display shows CD sign, playing begins to start automatically. When the last track on disc playing finished, the disc track number will return to track one, and play again.
3.Press the( )button to eject the CD disc from the slot; If the disc has not yet been taken away within 10 seconds, it will automatically be loaded into the slot again, but will not play.
INSERT/ EJECT CD DISC
When short pressing: The radio searches for each preset station. When the field strength level is more than the threshold level of stop level, the radio is holding at preset number for few secretary with releasing mute, and than searches again. In FM band,FM1,FM2 and FM3 is checked one at a time. When long pressing(more than 1 secretary ) The radio searches from the current frequency and checks the signal strength, level until 1cycle search is finished. And then 6 strongest stations are preset to the corresponding preset number. The AS operation is finished, the radio executes the Preset scan.
AS/PS SEARCH
1)RADIO MODE.
-Frequency moves one step up/down when press T-UP/DOWN key is pressed for less than 500ms.
-SEEK MODE is activated as below when T-UP/DOWN key is pressed for longer than500ms. *Establishing SEEK MODE from the MENU.
-SEEK2:SEEK is activated after key is released.
2)CDP MODE.
-TRACK UP/DOWN is activated when key is pressed for less than 500ms .Track returns to the beginning of the song when play has been on for longer than 3 sec.
-SEARCH FF/FR is activated when T-UP/DN key is pressed for longer than 500ms. Search function is activated up to the first track at 0min 0sec,then resumes play.
-SEEK1:SEEk is activated right away when key is pressed for longer than 500ms.
T-UP/ DOWN
When pressed short, It is used as the selection of each function. When a mode is selected, the sound source switching is controlled in E.V.R. And relative port control is also implemented. >RADIO >CDP >TAP >AUX When a CDP is existed inside, S-CDP of individual segment is turned on.
MODE
When system is on, by pressing this key, the radio system goes into power off mode. All information about its current setting, and restores the information when switched on again. The system comes to ON by pressing any key.
POWER ON/OFF
1
2
3
4
2
EJECT BUTTON push down to eject the cassette tape.
3
CASSETTE COMPARTMENT Insert a tape into the cassette compartment. The unit will automatically switch from 'TAPE' will be shown on display.
4
FAST FORWARD/REWIND/PROGRAM BUTTON Fast forward/rewind: Press the button with the double arrows pointing the same direction as the direction indicator in the LCD to fast forward. Press the other button in the opposite direction to rewind. Program: Push down both buttons together to play the other side of the tape.
1
RESET BUTTON
USA
EUR
Radio frequency area option:(see the pict re )u
GETTING STARTED
Loading...