Specifications
RDS638BA
MP3-Compatible FM CD Receiver
CD/MP3 PLAYER
Signal to Noise Ratio > 60dB
Channel Separation > 45 dB
Frequency Response 20Hz - 20 kHz
RADIO
FM Section:
Frequency range 87.5-108 MHz
Intermediate frequency 10.7 MHz
Sensitivity 3 µV
Stereo separation 30 dB
Signal to noise ratio 50 dB
Channel step 50 kHz
TONE CONTROLS
Bass (at 100Hz) +/- 10 dB
Treble (at 10kHz) +/- 10 dB
LINE-OUT
Output 5 V (max.)
Impedance 10kOhm
AMPLIFIER
Maximum output power 80 watts x 4 channels
GENERAL
Power Supply 12V DC (10.8-15.6V allowable)
Chassis dimensions 7” x 6-1/4” x 2” (178 x 159 x 51 mm)
Weight 4.4 lb. (2 kg)
Instructions on environment protection
Do not dispose of this product in the usual household garbage at the end of its lifecycle; hand it over at a collection point for the recycling of electrical and electronic
appliances. The symbol on the product, the instructions for use or the packing will
inform about the methods for disposal.
The materials are recyclable as mentioned in this marking. By recycling, material recycling or other forms of reutilization of old appliances, you are making an important
contribution to protect our environment.
Please inquire at the community administration for the authorized disposal location.
17
RDS638BA
MP3-Compatible FM CD Receiver
U S E R ’ S M A N U A L
CONTENTS
Installation
DIN front-mount installation
DIN rear-mount installation
Removing the head unit
Detaching the front panel
Replacing the front panel
General controls
Radio controls
Audio controls
RDS controls
CD/MP3 Playback controls
How to select MP3 files
Controls behind faceplate
USB and Front side AUX IN operations
Remote control functions
2
3
4
4
5
5
6
7
8
8
10
11
11
12
13
How to use bluetooth in your car audio
Wiring diagram
Troubleshooting
Specifications
14
15
16
17
1
234
Before removing the bezel, press the
RELEASE button to remove the front panel.
Release Button
press RELEASE to release
the front panel...
Release Button
press RELEASE to release
the front panel...
5
Front panel controls
TA SEEK
AUDIO
2 sec.
AUDIO
AUDIO
MASK DPI
AUDIO
ESP
ESP 10 / ESP 40
TA SEEK
AUDIO
2 sec.
TA SEEK / TA ALARM
TA SEEK
AUDIO
MASK DPI
AUDIO
2 sec.
MASK DPI / MASK ALL
TA SEEK
AUDIO
RETUNE
AUDIO
RETUNE DSP
AUDIO
MASK DPI
AUDIO
TA SEEK
AUDIO
2 sec.
AUDIO
AUDIO
MASK DPI
AUDIO
RETUNE DSP
AUDIO
TA SEEK
AUDIO
2 sec.
AUDIO
DSP ONMASK DPI
AUDIO
RETUNE
AUDIO
2 sec.
RETUNE L / RETUNE S
POP --- ROCK --- CLASSIC --- FLAT --- DSP OFF
LOUD
LOUD ON/OFF
TA SEEK
AUDIO
2 sec.
AUDIO
LOUD
AUDIO
MASK DPI
AUDIO
AUDIO
RETUNE DSP
AUDIO
ESP
AUDIO
AUDIO
MULTI
BEEP ON/OFF
AUDIO AUDIO
BEEP
VOL
SCROLL
TA SEEK
AUDIO
2 sec.
AUDIO
LOUD
AUDIO
MASK DPI
AUDIO
AUDIO
RETUNE DSP
AUDIO
ESP
MULT ON/OFF
AUDIO
MULT
VOL
TA SEEK
AUDIO
2 sec.
AUDIO
LOUD
AUDIO
MASK DPI
AUDIO
AUDIO
RETUNE DSP
AUDIO
ESP
AUDIO AUDIO
MULT
VOL
VOL
VOL
VOL
VOL
VOL
SCROLL SCROLL 1/2
VOL
TA SEEK
AUDIO
2 sec.
AUDIO
AUDIO
MASK DPI
AUDIO
ESP
ESP 10 / ESP 40
TA SEEK
AUDIO
2 sec.
TA SEEK / TA ALARM
TA SEEK
AUDIO
MASK DPI
AUDIO
2 sec.
MASK DPI / MASK ALL
TA SEEK
AUDIO
RETUNE
AUDIO
RETUNE DSP
AUDIO
MASK DPI
AUDIO
TA SEEK
AUDIO
2 sec.
AUDIO
AUDIO
MASK DPI
AUDIO
RETUNE DSP
AUDIO
TA SEEK
AUDIO
2 sec.
AUDIO
DSP ONMASK DPI
AUDIO
RETUNE
AUDIO
2 sec.
RETUNE L / RETUNE S
POP --- ROCK --- CLASSIC --- FLAT --- DSP OFF
LOUD
LOUD ON/OFF
AUDIO
TA SEEK
AUDIO
2 sec.
AUDIO
LOUD
AUDIO
MASK DPI
AUDIO
AUDIO
RETUNE DSP
AUDIO
ESP
MULT ON/OFF
AUDIO
MULT
VOL
TA SEEK
AUDIO
2 sec.
AUDIO
LOUD
AUDIO
MASK DPI
AUDIO
AUDIO
RETUNE DSP
AUDIO
ESP
AUDIO AUDIO
MULT
VOL
VOL
VOL
VOL
VOL
VOL
SCROLL SCROLL 1/2
VOL
GENERAL CONTROLS
POWER Press any button to turn unit ON. To turn
head unit off, press and hold POWER.
RELEASE Press to release and remove the front panel.
DISP When this key is pressed, it is operated as the conversion of each
display mode as follow.
1) In case of receiving RDS station.
RADIO MODE
PS ---- CT ---- FREQ ---- PTY
CD/MP3 PLAYER MODE
CDP ---- CT ---- PS ---- FREQ ---- PTY
2) In case of receiving NON RDS station
RADIO MODE
FREQ ---- CLOCK ----NO PTY
CD/MP3 PLAYER MODE
CDP ---- FREQ ---- CLOCK ---- NO PTY
Each display time is several seconds, and come back to 1’st position after
several seconds.
Notes: • CT = clock time • FREQ = frequency • CDP = CD player
6
The Liquid Crystal Display will display the current state of the unit.
SCROLL MODE When press the AUDIO button for more than 2 seconds, it is
activated as selecting mode of these function.
SCROLL 1: Unit displays song details but no text scrolling.
SCROLL 2: Unit displays song details and scrolls the text information to the left.
BEEP MODE When press the AUDIO button for more than 2 seconds, it is activated as selecting mode of these function.
BEEP ON: BEEP sound can hear from speaker when the buttons are pressed.
RADIO CONTROLS
TA SEEK
AUDIO
2 sec.
AUDIO
AUDIO
MASK DPI
AUDIO
ESP
ESP 10 / ESP 40
TA SEEK
AUDIO
2 sec.
TA SEEK / TA ALARM
TA SEEK
AUDIO
MASK DPI
AUDIO
2 sec.
MASK DPI / MASK ALL
TA SEEK
AUDIO
RETUNE
AUDIO
RETUNE DSP
AUDIO
MASK DPI
AUDIO
TA SEEK
AUDIO
2 sec.
AUDIO
AUDIO
MASK DPI
AUDIO
RETUNE DSP
AUDIO
TA SEEK
AUDIO
2 sec.
AUDIO
DSP ONMASK DPI
AUDIO
RETUNE
AUDIO
2 sec.
RETUNE L / RETUNE S
POP --- ROCK --- CLASSIC --- FLAT --- DSP OFF
AUDIO
LOUD
LOUD ON/OFF
TA SEEK
AUDIO
2 sec.
AUDIO
LOUD
AUDIO
MASK DPI
AUDIO
AUDIO
RETUNE DSP
AUDIO
ESP
AUDIO
AUDIO
MULTI
TA SEEK
AUDIO
2 sec.
AUDIO
LOUD
AUDIO
MASK DPI
AUDIO
AUDIO
RETUNE DSP
AUDIO
ESP
AUDIO
MULT
AUDIO
AUDIO AUDIO
TA SEEK
AUDIO
2 sec.
AUDIO
LOUD
AUDIO
MASK DPI
AUDIO
AUDIO
RETUNE DSP
AUDIO
ESP
AUDIO
MULT
STEREO/MONO
STEREO
AUDIO
BEEP
VOL
AUDIO
SEEK1 / SEEK 2SEEK
BEEP
VOL
BEEP ON/OFF
AUDIO AUDIO
BEEP
VOL
SCROLL
SCROLL
SCROLL
TA SEEK
AUDIO
2 sec.
AUDIO
LOUD
AUDIO
MASK DPI
AUDIO
AUDIO
RETUNE DSP
AUDIO
ESP
MULT ON/OFF
AUDIO
MULT
VOL
TA SEEK
AUDIO
2 sec.
AUDIO
LOUD
AUDIO
MASK DPI
AUDIO
AUDIO
RETUNE DSP
AUDIO
ESP
AUDIO AUDIO
MULT
VOL
VOL
VOL
VOL
VOL
VOL
SCROLL SCROLL 1/2
VOL
TA SEEK
AUDIO
2 sec.
AUDIO
AUDIO
MASK DPI
AUDIO
ESP
ESP 10 / ESP 40
TA SEEK
AUDIO
2 sec.
TA SEEK / TA ALARM
TA SEEK
AUDIO
MASK DPI
AUDIO
2 sec.
MASK DPI / MASK ALL
TA SEEK
AUDIO
RETUNE
AUDIO
RETUNE DSP
AUDIO
MASK DPI
AUDIO
TA SEEK
AUDIO
2 sec.
AUDIO
AUDIO
MASK DPI
AUDIO
RETUNE DSP
AUDIO
TA SEEK
AUDIO
2 sec.
AUDIO
DSP ONMASK DPI
AUDIO
RETUNE
AUDIO
2 sec.
RETUNE L / RETUNE S
POP --- ROCK --- CLASSIC --- FLAT --- DSP OFF
AUDIO
LOUD
LOUD ON/OFF
TA SEEK
AUDIO
2 sec.
AUDIO
LOUD
AUDIO
MASK DPI
AUDIO
AUDIO
RETUNE DSP
AUDIO
ESP
AUDIO
AUDIO
MULTI
TA SEEK
AUDIO
2 sec.
AUDIO
LOUD
AUDIO
MASK DPI
AUDIO
AUDIO
RETUNE DSP
AUDIO
ESP
AUDIO
MULT
AUDIO
AUDIO AUDIO
TA SEEK
AUDIO
2 sec.
AUDIO
LOUD
AUDIO
MASK DPI
AUDIO
AUDIO
RETUNE DSP
AUDIO
ESP
AUDIO
MULT
AUDIO
TA SEEK
AUDIO
2 sec.
AUDIO
LOUD
AUDIO
MASK DPI
AUDIO
AUDIO AUDIO
RETUNE DSP
AUDIO
ESP
MULT
LOCAL/DX
LOCAL
AUDIO
STEREO
AUDIO
BEEP
VOL
STEREO/MONO
STEREO
AUDIO
BEEP
VOL
AUDIO
SEEK1 / SEEK 2SEEK
BEEP
VOL
BEEP ON/OFF
AUDIO AUDIO
BEEP
VOL
SCROLL
SCROLL
SCROLL
AUDIO
SCROLL
TA SEEK
AUDIO
2 sec.
AUDIO
LOUD
AUDIO
MASK DPI
AUDIO
AUDIO
RETUNE DSP
AUDIO
ESP
MULT ON/OFF
AUDIO
MULT
VOL
TA SEEK
AUDIO
2 sec.
AUDIO
LOUD
AUDIO
MASK DPI
AUDIO
AUDIO
RETUNE DSP
AUDIO
ESP
AUDIO AUDIO
MULT
VOL
VOL
VOL
VOL
VOL
VOL
SCROLL SCROLL 1/2
VOL
AS/PS Select six strong stations and store them in current band.
1. Select a band (if needed)
2. Hold A/PS button for more than three seconds. The new stations
replace stations already stored in that band.
Preset Scan
Scan stations stored in current band
1. Select a band (if needed)
2. Touch A/PS for more than one second but less than three seconds.
Radio pauses for five seconds at each station. Touch A/PS again to stop
scanning when desired station is reached.
BAND Push this switch to select the desired band. Selection is made in
regular sequence as FM1-FM2-FM3.
STEREO/MONO MODE When press AUDIO button for more than 2 seconds, it is activated
as selecting mode of these function.
When FM stations are weak and are disturbed, listening can be improved by selecting MONO.
LOCAL/DX MODE When press AUDIO button for more than 2 seconds, it is activated as
selecting mode of these function.
“Local” position in areas with strong signals to let radio stop at only strong stations
during manual tuning (LOC appears). Press to Distant position in areas with weak
signals to listen to all stations.
STATION PRESETS Six numbered preset button store and recall stations
for each band.
Storing a station:
1. Select a band (if needed)
2. Select a station
3. Hold a preset button longer than one second. Preset station number
appears in the display when station is saved.
Recall a station:
1. Select band (if needed)
2. Press a preset button for less than one second to select stored station.
TUNE BUTTONS When pressed for less than 1 second, these keys operate as
manual tuning mode.
When pressed longer than 1 sec., they are operated as SEEK tuning mode.
If the keys are not pressed for 3 seconds, they will return to SEEK mode again.
7
Front panel controls
TA SEEK
AUDIO
2 sec.
AUDIO
AUDIO
MASK DPI
AUDIO
TA SEEK
AUDIO
2 sec.
TA SEEK / TA ALARM
TA SEEK
AUDIO
MASK DPI
AUDIO
2 sec.
MASK DPI / MASK ALL
TA SEEK
AUDIO
RETUNE
AUDIO
RETUNE DSP
AUDIO
MASK DPI
AUDIO
TA SEEK
AUDIO
2 sec.
AUDIO
DSP ONMASK DPI
AUDIO
RETUNE
AUDIO
2 sec.
RETUNE L / RETUNE S
POP --- ROCK --- CLASSIC --- FLAT --- DSP OFF
LOUD ON/OFF
VOL
VOL
VOL
VOL
VOL
TA SEEK
AUDIO
2 sec.
TA SEEK / TA ALARM
TA SEEK
AUDIO
MASK DPI
AUDIO
2 sec.
MASK DPI / MASK ALL
TA SEEK
AUDIO
RETUNE
AUDIO
MASK DPI
AUDIO
TA SEEK
AUDIO
2 sec.
AUDIO
DSP ONMASK DPI
AUDIO
RETUNE
AUDIO
2 sec.
RETUNE L / RETUNE S
POP --- ROCK --- CLASSIC --- FLAT --- DSP OFF
VOL
VOL
VOL
VOL
AUDIO CONTROLS
SUB Press to engage subwoofer output.
SOURCE By pressing this key, user can select AUX/TUNER/CDMP3/USB mode.
AUDIO BUTTON and ROTARY CONTROL Press the button repeatedly to
access Volume, Bass, Treble, Balance and Fader functions. Then use the knob
to adjust the selected function.
DSP MODE When press AUDIO button for more than 2 seconds, it is
activated as selecting mode of these function.
RDS CONTROLS
The RDS (Radio Data System) is a digital information system developed by the EBU (European
Broadcast Union). Piggy-backed on normal FM broadcasts, RDS offers a variety of information
services and automatic retuning functions for RDS-compatible car stereos.
In 1988, RDS became available in the United Kingdom, France, West Germany, Ireland and Sweden.
Test transmissions are being conducted in many other european countries. It is expected that RDS
will be available in most western european countries in the near future.
8
POP, ROCK, CLASSIC, FLAT or DSP OFF selected by rotary VOL left or right
LOUD MODE When press AUDIO button for more than 2 seconds, it is
activated as selecting mode of these function.
LOUD ON/OFF mode is selected by rotary VOL left or right. Increase the level
of bass output.
TA SEEK
AUDIO
2 sec.
TA SEEK / TA ALARM
TA SEEK
AUDIO
MASK DPI
AUDIO
2 sec.
MASK DPI / MASK ALL
VOL
VOL
RDS CONTROLS
TA SEEK
AUDIO
2 sec.
TA SEEK / TA ALARM
VOL
TA SEEK
AUDIO
2 sec.
TA SEEK / TA ALARM
TA SEEK
AUDIO
MASK DPI
AUDIO
2 sec.
MASK DPI / MASK ALL
TA SEEK
AUDIO
RETUNE
AUDIO
MASK DPI
AUDIO
2 sec.
RETUNE L / RETUNE S
VOL
VOL
VOL
TA When pressed short, it is activated as TA mode on or off
When TA mode is on and traffic announcement is transmitted
– When the unit is it CD/MP3 mode, it will switch to radiomode temporarily.
– If the volume level was under the threshold point, it will be raised to the threshold point.
– When TP station is received, TP segment is turned on in LCD display.
AF When pressed short, AF/REG switching mode is selected.
When AF/REG switching mode is selected, the radio checks the signal strength of the AF all the
time. When pressed long, it is activated as regional mode ON/OFF.
– Regional mode ON:
AF switching or PI SEEK is implemented to the station which have all PI codes same as current
station. REG segment is turned on, in LCD display.
– Regional mode OFF:
The regional code in the format of PI code is ignored when AF switching or PI SEEK is implemented.
PTY While selecting PTY type, its selection is implemented by preset buttons as described in
preset key. When PTY is selected, the radio starts to search corresponding PTY information, and
stops if the corresponding PTY information is detected.
When PTY mode is selected, the PTY switch is shared as follows:
PTY music group ---- PTY speech group ---- OFF
MUSIC SPEECH
1. POP M, ROCK M 1. NEWS, AFFAIRS, INFO
2. EASY M, LIGHT M 2. SPORT, EDUCATE, DRAMA
3. CLASSICS, OTHER M 3. CULTURE, SCIENCE, VARIED
4. JAZZ, COUNTRY 4. WEATHER, FINANCE, CHILDREN
5. NATION M, OLDIES 5. SOCIAL, RELIGION, PHONE IN
6. FOLK M 6. TRAVEL, LEISURE, DOCUMENT
TA SEEK/TA ALARM MODE When press AUDIO button for more than 2 seconds, it is activated
as selecting mode of these function.
TA SEEK Mode or TA ALARM mode is selected by rotary VOL left or right.
- TA SEEK mode:
When newly turned station does not receive TP information for 5 sec., the radio retunes to next
station which has not the same station (PI) as the last station, but has the TP information.
In TA seek mode, the current station can be changed to the completely different station because
the unit searches TP station when the field strength of the current station is very weak, or the
current station has no TP signal.
- TA ALARM mode:
Any automatic retune mode is not activated, just can hear Beep sound.
MASK DPI MODE When press AUDIO button for more than 2 seconds, it is activated as selecting mode of these function.
MASK DPI: masked only the AF which has different PI.
MASK ALL: masked the AF which has different PI and NO RDS signal with field strength.
RETUNE L / S MODE When press AUDIO button for more than 2 seconds, it is activated as
selecting Retune mode.
RETUNE L: Select 90 seconds as the initial time of automatic TA search.
RETUNE S: Select 30 seconds as initial time.
9
CD/MP3 PLAYBACK CONTROLS
TA SEEK
AUDIO
2 sec.
AUDIO
AUDIO
MASK DPI
AUDIO
ESP
ESP 10 / ESP 40
TA SEEK
AUDIO
2 sec.
TA SEEK / TA ALARM
TA SEEK
AUDIO
MASK DPI
AUDIO
2 sec.
MASK DPI / MASK ALL
TA SEEK
AUDIO
RETUNE
AUDIO
RETUNE DSP
AUDIO
MASK DPI
AUDIO
TA SEEK
AUDIO
2 sec.
AUDIO
AUDIO
MASK DPI
AUDIO
RETUNE DSP
AUDIO
TA SEEK
AUDIO
2 sec.
AUDIO
DSP ONMASK DPI
AUDIO
RETUNE
AUDIO
2 sec.
RETUNE L / RETUNE S
POP --- ROCK --- CLASSIC --- FLAT --- DSP OFF
LOUD
LOUD ON/OFF
AUDIO
VOL
VOL
VOL
VOL
VOL
VOL
EJECT Press to eject CD
TUNE/TRACK BUTTONS Press and release
to advance to next track or to return to
the beginning of the current track (track
number will be displayed). Press and hold
to fast forward or reverse. Play will begin
at the point when you release the button.
PAUSE Press to pause CD playback. Press
again to resume playback
ESP MODE When press AUDIO button for
more than 2 seconds, it is activated as
10 sec. or 45 sec. of ESP mode can be
selected.
+10 10 TRACK UP SELECT:
(In case of MP3 files)
-10 10 TRACK DOWN SELECT:
(In case of MP3 files)
SHUFFLE Press to play ALL tracks
on the CD in random order.
CD SCAN Press to hear first several
seconds of each track on current disc.
Press again to stop intro and listen to
intro last previewed.
TOP Press to play first song of disc.
REPEAT Press and release to continuously repeat
same track. Press again to stop repeat cycle.
CD/MP3 Operation
To PLAY a CD gently insert a CD with the label side up into the disc slot. It will automatically
load and begin playing the first track.
To EJECT a CD press EJECT to stop the CD playback and eject the CD from the slot. The receiver
will automaticvally switch to radio mode.
To PAUSE a CD press PAUSE to stop playback temporarily. Press again to resume playback.
To SKIP TRACKS press the or key to choose the next or preceding track.
To FAST FORWARD or REVERSE press and hold the or key to the desired location
10
on the disc. Releasing the button starts playback at the location.
To REPEAT a TRACK press REPEAT to continuously repeat the current track. Press again to
return to normal playback mode.
To PREVIEW ALL TRACKS press CD SCAN to play the first several seconds of each track. Press
it again to stop an play the current track being previewed.
To PLAY TRACKS IN RANDOM ORDER press SHUF to play ALL tracks on the CD in random
mode. Press again to cancel this function.
Front panel controls
RESET
AUX IN
How to select MP3 files
Searching Track:
• Press and hold “AS/PS”, then search track is activated. First digit will flash.
• Rotate “VOL knob to right or left”, select first digit desired.
• Press “AUDIO” button, then the first digit is fixed and second digit will flash.
• Rotate “VOL knob to right or left”, select 2’nd 3’rd respectively.
• Then automatically the song selected will start.
Searching Directory:
• Press and hold “AS/PS”. Press “AS/PS” again, then directory search is activated.
• Rotate “VOL knob to right or left”, you can select the desired directory.
• Press “AUDIO” button again, then the directory is fixed and the first file name is displayed.
• Rotate clockwise to select the desired song.
• Press “AUDIO” button, then the song selected will start.
Searching File Name:
• Press and hold “AS/PS”. Press “AS/PS” twice, then character search mode is activated. “*”
character is displayed.
• Rotate “VOL knob to right or left”, you can select the desired letter.
• Press “AUDIO” button longer than 2 sec.
• The song with the same character you selected is displayed.
• Rotate clockwise to select the desired song.
• Press “AUDIO” button, then the song selected will start.
Controls behind faceplate
CD Loading/unloading slot
LED This LED flashes when the faceplate is
removed.
RESET Press this button with a ballpoint pen or other thin object.
The reset button is to be activated for the following reason:
Initial installation of the unit when all wiring is completed.
All the function button do not operate.
Error symbol on the display.
NOTE: If the unit does not function properly after you have
pressed the RESET button, clean the socket and the connector on the rear of the front panel with a cotton swab soaked
in isopropyl alcohol and try again.
11
USB and Front side AUX IN operations
TA SEEK
AUDIO
2 sec.
AUDIO
AUDIO
MASK DPI
AUDIO
ESP
ESP 10 / ESP 40
TA SEEK
AUDIO
2 sec.
TA SEEK / TA ALARM
TA SEEK
AUDIO
MASK DPI
AUDIO
2 sec.
MASK DPI / MASK ALL
TA SEEK
AUDIO
RETUNE
AUDIO
RETUNE DSP
AUDIO
MASK DPI
AUDIO
TA SEEK
AUDIO
2 sec.
AUDIO
AUDIO
MASK DPI
AUDIO
RETUNE DSP
AUDIO
TA SEEK
AUDIO
2 sec.
AUDIO
DSP ONMASK DPI
AUDIO
RETUNE
AUDIO
2 sec.
RETUNE L / RETUNE S
POP --- ROCK --- CLASSIC --- FLAT --- DSP OFF
LOUD
LOUD ON/OFF
AUDIO
TA SEEK
AUDIO
2 sec.
AUDIO
LOUD
AUDIO
MASK DPI
AUDIO
AUDIO
RETUNE DSP
AUDIO
ESP
MULT ON/OFF
AUDIO
MULT
VOL
VOL
VOL
VOL
VOL
VOL
VOL
USB Port Enhanced control of connected Portable Media such as
Flash Drives and digital MP3 Players, by using function keys on
the main unit or the remote control unit.
This unit features the latest ID3 Tag support, which allows you
to see the song’s name and which folder it’s located in, on the
LCD display.
AUX IN Convenient easy to use front “AUX IN” input jack, allows easy connection of Portable Media and other digital MP3
Players.
CD MULTI SECTION MODE When press AUDIO button for more than 2
seconds, it is activated as selecting mode of these function.
* IMPORTANT INFORMATION:
Because there are a great numBer and varieties of usB products, we can not guarantee
that our product will operate 100% with these devices.
12
CD MULTI ON/OFF mode is selected by rotary VOL left or right
CD MULTI ON: Read multi section CD.
CD MULTI OFF: Read first section only.
Tel /
*
#
POWER
2
INTRO
10-UP AF TA10-DN
3 41
6 7 85
TOP
SEL
MENU
BAND
VOL
VOL
SHUF
ST/MOPTY
SCAN SUB
TUNE/SEEK
AS/PS
RPT MUTE
MODE
09
DISP
Remote controls functions
1. POWER ON / OFF
2. ANSWER A CALL
3. VOLUME +
4. DISP / END A CALL
5. BAND / CD PLAY / PAUSE
6. TUNE / SEEK
7. SEL / MENU
8. CD REPEAT /
AUTO STORE/PRESET SCAN
9. VOLUME -
10. MUTE / MODE
11. CD PLAYER FIRST SONG
12. CD SCAN
13. PHONE NUMBER /
BUTTON 1-6: STATION
PRESETS
14. CD SHUFFLE
15. 10 TRACK DOWN SELECT
16. 10 TRACK UP SELECT
17. ALTERNATIVE FREQUENCIES
18. TRAFFIC ANNOUNCEMENT
19. PROGRAM TYPE
20. STEREO / MONO MODE
21. RADIO SCAN / PHONE
22. SUBWOOFER
12
11
16
15
20
19
1
32 4
6
5
8
7
9
10
13
14
17
18
21
22
Note: You can dial calls with this remote control. Please refer to “Making Calls Using the Dial Keypad”.
13
How to use bluetooth in your car audio
HOW TO PERFORM PAIRING
Before you can dial out from the car stereo, you must first perform
PAIRING. Pairing is a procedure used to connect 2 Bluetooth devices
together.
1. Press and hold AUDIO button for 2 seconds.
2. Press AUDIO button repeatedly until “PAIRING” displays.
3. Press and hold AUDIO button to engage paring mode. “PAIRING”
blinks on the display.
4. Turn on the Bluetooth feature of your mobile phone. Perform “Add
Bluetooth device” from your mobile phone. The mobile will search
for any Bluetooth devices within the range. Select “BHF207C” and
enter Passkey: “0000” to connect to the car audio. (Please refer to the
instruction manual of your mobile phone for Bluetooth Pairing).
5. The LCD will display “PAIRED” after successful pairing.
Note:
• If “DISCONN” shows instead of “PAIRING”, it means the head unit cur-
rently is paired with another device. Press and hold AUDIO button to
disconnect the connection and perform steps above again.
• “BHF207C” is the Bluetooth device name of the car stereo.
• Refer to your cellular user manual for the proper procedures of pairing
Bluetooth devices.
Audio Streaming
If your phone is “A2DP” format compatible, then you can play music in your mobile and
the sound will be transferred to car head unit.
1. Make sure your mobile and the unit is properly paired and connected.
2. Play the music through your mobile music player software.
3. Press SOURCE repeatedly until “BT-PLAY” appears in the display. The sound will be
transferred to the head unit.
Making Calls Using the Dial Keypad
You can make calls directly from the supplied Dial Keypad. Before you make calls, make
sure that the devices are properly paired and the keypad cable properly connected to the
back of the head unit.
1. Press PHONE button or press and hold (*) on the keypad.
2. Enter the phone number via the keypad and press button to dial out. Press
button to make corrections when entering numbers.
3. Press button to end call.
Tips: Press PHONE on the head unit is the same as press and hold (*) on the keypad.
Answering / Hanging Up
To answer a call, press the button on the dial keypad. Speak directly to the keypad’s microphone. Once you have finished your conversation, press the button to hang up.
Calls (Outgoing, Incoming)
The unit stores all the incoming and outgoing calls. Use this feature to check the numbers and
make calls from it.
“OUT NUM” – outgoing calls made through the dial keypad.
1. Press PHONE then press and hold AUDIO button for 2 seconds. “OUT NUM” displays.
2. Press and hold AUDIO button again.
3. Rotate volume knob to search for entries and press to call.
“IN NUM” – incoming calls received.
1. Press PHONE then press and hold AUDIO button for 2 seconds.
2. Press AUDIO button repeatedly until “IN NUM” displays.
3. Press and hold AUDIO button again.
4. Rotate volume knob to search for entries and press to call.
Adding Contacts
The unit can save contact telephone number for quick access.
1. Press PHONE then press and hold AUDIO button for 2 seconds.
2. Press AUDIO button repeatedly until “ADD NUM” displays.
3. Press and hold AUDIO button again.
4. Using volume knob, enter the name of the contact. Press AUDIO to save each character
entered. Press and hold AUDIO to save name.
5. Enter the phone number. Press AUDIO to save each number entered.
6. Press and hold AUDIO to save entry.
Finding Contacts
After adding contacts, you can use this feature to find them.
1. Press PHONE then press and hold AUDIO button for 2 seconds.
2. Press AUDIO button repeatedly until “FIND NUM” displays.
14
CONNECTOR A
4. CONSTANT +12V
5. AUTO ANTENNA OUTPUT
7. IGNITION SWITCHED +12V
8. GROUND
CONNECTOR B
1. REAR RIGHT SPEAKER (+)
2. REAR RIGHT SPEAKER (-)
3. FRONT RIGHT SPEAKER (+)
4. FRONT RIGHT SPEAKER (-)
5. FRONT LEFT SPEAKER (+)
6. FRONT LEFT SPEAKER (-)
7. REAR LEFT SPEAKER (+)
8. REAR LEFT SPEAKER (-)
L (WHITE)
SUB WOOFER
LINE IN
R (RED)
L (WHITE)
LINE OUT
(REAR)
R (RED)
LINE OUT
(FRONT)
L (WHITE)
ANTENNA
CONNECTOR
ISO CONNECTOR
R (RED)
B
A
1234567
8
4
5 7
8
DIAL KEYPAD
3. Press and hold AUDIO button again.
4. Using volume knob, select the name of the contact and press to call.
Deleting Contacts
1. Press PHONE then press and hold AUDIO button for 2 seconds.
2. Press AUDIO button repeatedly until “FIND NUM” displays.
3. Press and hold AUDIO button again.
4. Rotate volume knob until the name of the contact you want to delete displays.
5. Press and hold for 2 seconds to delete contact.
How to Set Incoming Call Melody
1. Press PHONE then press and hold AUDIO button for 2 seconds.
2. Press AUDIO button repeatedly until “MELODY” displays.
3. Rotate volume knob to the desired melody.
How to Set Incoming Call Ring Volume
1. Press PHONE then press and hold AUDIO button for 2 seconds.
2. Press AUDIO button repeatedly until “RING” displays.
3. Rotate volume knob to the desired level.
How to Set Conversation Volume
1. Press PHONE then press and hold AUDIO button for 2 seconds.
2. Press AUDIO button repeatedly until “TEL” displays.
3. Rotate volume knob to the desired level.
Disconnect Paired Devices
You can disconnect to an already paired Bluetooth device from your car stereo.
1. Press PHONE then press and hold AUDIO button for 2 seconds.
2. Press AUDIO button repeatedly until “DISCONN” displays.
3. Press and hold AUDIO button again to disconnect.
Electrical connections
15
16
Loading...