Page 1
HS-7322
Intel® GM45/Mobile Dual-Core processor
PICMG1.3 Half-size SBC
•1066/800/667MHz FSB•CompactFlash•
•8-bit GPIO•DVI-I/CRT/LVDS•Dual GB LAN•
•Audio•SATA•RS-232/422/485•4 COM•
•7 USB2.0•WDT•H/W Monitor•
Page 2
Copyright Disclaimers
The accuracy of contents in this manual has passed thorough checking and review before
publishing. BOSER Technology Co., Ltd., the manufacturer and publisher, is not liable for
any infringements of patents or other rights resulting from its use. The
manufacturer will
not be responsible for any direct, indirect, special, incidental or consequential
damages arising from the use of this product or documentation, even if advised of
the possibility of such damage(s).
This manual is copyrighted and BOSER Technology Co., Ltd. reserves all
documentation rights. Unauthorized reproduction, transmission, translation, and
storage of any form and means (i.e.,
electronic, mechanical, photocopying, recording)
of this document, in whole or partly, is prohibited, unless granted permission by BOSER
Technology Co., Ltd.
BOSER Technology Co., Ltd. reserves the right to change or improve the contents of
this document without due notice.
BOSER Technology Co., Ltd. assumes no
responsibility for any errors or omissions that may appear in this manual, nor does
it make any commitment to update the information contained herein.
T
T
T
r
r
r
a
a
a
d
d
d
e
e
e
m
m
m
a
a
a
r
r
r
k
k
k
s
s
s
BOSER is a registered trademark of BOSER Technology Co., Ltd.
ISB is a registered trademark of BOSER Technology Co., Ltd.
Intel is a registered trademark of Intel Corporation.
Award is a registered trademark of Award Software, Inc.
AMI is a registered trademark of AMI Software, Inc.
All other trademarks, products and or product names mentioned herein are
mentioned for identification purposes only, and may be trademarks and/or
registered trademarks of their respective companies or owners.
© Copyright 2009 BOSER Technology Co., Ltd.
All Rights Reserved.
Edition 1.6, October 06, 2010
Page 3
Table of Contents
Chapter 1 General Description ..................................1
1.1 Major Features....................................................................... 2
1.2 Specifications ........................................................................ 2
1.3 Board Dimensions................................................................. 4
Chapter 2 Unpacking ..................................................5
2.1 Opening the Delivery Package............................................. 5
2.2 Inspection............................................................................... 5
Chapter 3 Hardware Installation ..............................7
3.1 Before Installation ................................................................. 7
3.2 Board Layout ......................................................................... 8
3.3 Jumper List ............................................................................ 9
3.4 Connector List ....................................................................... 9
3.5 Configuring the CPU ........................................................... 10
3.6 System Memory ................................................................... 10
3.7 VGA Controller .................................................................... 10
3.8 Serial ATA Connector ......................................................... 13
3.9 Serial Port Connectors ....................................................... 13
3.10 Ethernet Connector ............................................................. 14
3.11 USB Port............................................................................... 15
3.12 CMOS Data Clear ................................................................. 15
3.13 Parallel Port.......................................................................... 16
3.14 Power and Fan Connectors................................................ 16
3.15 Keyboard/Mouse Connectors ............................................ 17
3.16 System Front Panel Control ............................................... 17
3.17 Watchdog Timer .................................................................. 18
3.18 Audio Connectors ............................................................... 20
3.19 8-bit GPIO Function............................................................. 20
3.20 CompactFlash Socket...................................................... 21
Page 4
Chapter 4 AMI BIOS Setup..................................... 23
4.1 Starting Setup...................................................................... 23
4.2 Using Setup ......................................................................... 24
4.3 Main Menu............................................................................ 25
4.4 Advanced Settings .............................................................. 26
4.5 Advanced PCI/PnP Settings............................................... 29
4.6 Boot Settings ....................................................................... 30
4.7 Security Settings ................................................................. 31
4.8 Advanced Chipset Settings................................................ 32
4.9 Exit Options ......................................................................... 33
Chapter 5 Software Utilities..................................... 35
5.1 Chipset Driver Installation.................................................. 35
5.2 VGA Driver Installation ....................................................... 38
5.3 LAN Driver Installation........................................................ 41
5.4 Audio Driver Installation..................................................... 43
Page 5
Declaration of Conformity -- CE Mark
BOSER Technology hereby acknowledges that compliance testing in
accordance with applicable standards of the EU’s EMC Directive,
89/336/EEC, was successfully completed on a sample of the equipment
identified below:
Equipment Class: Information Technology Equipment
Product Model Series: HS-7322
This Product Complies With: EN55022: Class A for Radiated emissions
EN50082-2: Heavy Industrial EMC Immunity
We, the undersigned, hereby declare that the equipment specified above
conforms to the above directives and standards.
Manufacturer:
BOSER TECHNOLOGY CO., LTD.
Page 6
Safety Instructions
Integrated circuits on computer boards are sensitive to static electricity. To
avoid damaging chips from electrostatic discharge, observe the following
precautions:
Do not remove boards or integrated circuits from their anti-static packaging
until you are ready to install them.
Before handling a board or integrated circuit, touch an unpainted portion of
the system unit chassis for a few seconds. This helps to discharge any static
electricity on your body.
Wear a wrist-grounding strap, available from most electronic component
stores, when handling boards and components. Fasten the ALLIGATOR clip
of the strap to the end of the shielded wire lead from a grounded object.
Please wear and connect the strap before handle the HS-7322 to ensure
harmlessly discharge any static electricity through the strap.
Please use an anti-static pad when putting down any components or parts or
tools outside the computer. You may also use an anti-static bag instead of
the pad. Please inquire from your local supplier for additional assistance in
finding the necessary anti-static gadgets.
NOTE: DO NOT TOUCH THE BOARD OR ANY OTHER SENSITIVE
COMPONENTS WITHOUT ALL NECESSARY ANTI-STATIC
PROTECTIONS.
Page 7
1
Chapter 1
General Description
The HS-7322 is an Intel® GM45/ICH9-M chipset-based board
designed, the board supports Socket P for Intel® Mobile Dual-Core
processor. The HS-7322 is an ideal all-in-one PICMG1.3 Half-size
SBC. Additional features include an enhanced I/O with CF,
DVI-I/CRT/LVDS, dual GB LAN, audio, SATA, 4 COM, and 7 USB2.0
interfaces.
The Intel® GM45 integrated Intel® Graphics Media Accelerator 4500
MHD with 352MB video memory supports CRT/Panel displays up to
2048 x 1536. It also supports 24-bit single/dual-channel LVDS
interface.
System memory is also sufficient with the two 240-pin DIMM sockets
up to 4GB DDR2 SDRAM.
Page 8
2
Additional onboard connectors include seven advanced USB2.0 ports
providing faster data transmission. And two RJ-45 connectors for
10/100/1000 Based Ethernet uses. To ensure the reliability in an
unmanned or standalone system
, the watchdog timer (WDT) onboard
HS-7322 is designed with software that does not need the arithmetical
functions of a real-time clock chip. If any program causes unexpected
halts to the system, the onboard WDT will automatically reset the CPU
or generate an interrupt to resolve such condition.
1.1 Major Features
The HS-7322 comes with the following features:
¾ Socket P for Intel® Mobile Dual-Core processor, supports
1066/800/667MHz FSB
¾ 2 x DIMMs up to 4GB DDR2 SDRAM
¾ Intel® GM45/ICH9-M system chipset
¾ Intel® GM45 integrated for CRT & LVDS
¾ 2 x 10/100/1000 Mbps Ethernet
¾ High Definition audio codec
¾ Supports CF, 3 x SATA, 4 x COM, 7 x USB2.0
¾ Supports 24-bit LVDS, 8-bit GPIO, H/W Monitor function
¾ Option for DVI-I display
1.2 Specifications
z System
CPU:
Intel® Mobile Dual-Core processor, supports Merom 65nm and
Penryn 45nm (Socket P)
FSB:
1066/800/667MHz FSB
BIOS:
AMI PnP Flash BIOS
System Chipset:
Intel® GM45/ICH9-M
I/O Chipset:
Winbond W83627UHG
System Memory:
2 x 240-pin DIMM sockets DDR2 800MHz up to 4GB
Storage:
1 x Type II CF socket
Watchdog Timer:
Software programmable time-out intervals from 1~255 sec. or
1~255 min.
Page 9
3
H/W Status Monitor:
Monitoring temperatures, voltages, and cooling fan status
Operating Temperature:
0~+60 degrees C
Operating Humidity:
0~95%, non-condensing
Size (L x W):
167.6x 126.4 mm
z I/O Interface
MIO:
3 x RS-232
1 x RS-232/422/485
7 x USB2.0 (6 x internal, 1 x external)
1 x Parallel
3 x SATA
1 x PS/2 for KB/MS
GPIO:
8-bit general purpose input/output port
z Display
Chipset:
Intel® GM45 integrated Intel® Graphics Media Accelerator
4500 MHD
Display Memory:
352MB video memory
LVDS:
24-bit single/dual-channel
Resolution:
2048 x 1536
DVI Chipset:
Intel® GM45 integrated Intel® Graphics Media Accelerator
4500 MHD
z Audio
Chipset:
RealTek ALC262 High Definition audio codec
Audio Interface (w/pin header):
MIC In, Line Out
z Ethernet
Chipset:
Dual RealTek RTL8111C 10/100/1000 Mbps LAN
Ethernet Interface:
2 x RJ-45
Page 10
4
1.3 Board Dimensions
Page 11
5
Chapter 2
Unpacking
2.1 Opening the Delivery Package
The HS-7322 is packed in an anti-static bag. The board has
components that are easily damaged by static electricity. Do not
remove the anti-static wrapping until proper precautions have been
taken. Safety Instructions in front of this manual describe anti-static
precautions and procedures.
2.2 Inspection
After unpacking the board, place it on a raised surface and carefully
inspect the board for any damage that might have occurred during
shipment. Ground the board and exercise extreme care to prevent
damage to the board from static electricity.
Integrated circuits will sometimes come out of their sockets during
shipment. Examine all integrated circuits, particularly the BIOS,
processor, memory modules, ROM-Disk, and keyboard controller chip
to ensure that they are firmly seated. The HS-7322 delivery package
contains the following items:
HS-7322 Board x 1
Utility CD Disk x 1, including User’s Manual
Cables (as follow table)
Jumper Bag x 1
Page 12
6
Cables Package
NO. Description QTY.
1 SATA cable 50cm (w/Lock) 1
2 COM DB9*2-10P(2.0) 30cm w/bracket 1
3 Print DB25-26P(2.0) 27cm w/bracket 1
4 SPK 8P(2.0) phone jack*2 27cm w/bracket 1
5 SATA power cable 15cm 1
6 USB 1-to-2 cable 20cm w/bracket 1
7 6P(JST2.0)-Mini DIN*2 cable 20cm w/bracket 1
It is recommended that you keep all the parts of the delivery package
intact and store them in a safe/dry place for any unforeseen event
requiring the return shipment of the product. In case you discover any
missing and/or damaged items from the list of items, please contact
your dealer immediately.
Option Accessories
NO. Description
1 50cm SATA device cable
2 COM DB9*2-10P(2.0) 30cm w/bracket
3 USB 1-to-2 cable 20cm w/bracket
4 P-M Cooler, H=23mm
Page 13
7
Chapter 3
Hardware Installation
This chapter provides the information on how to install the hardware
using the HS-7322. This chapter also contains information related to
jumper settings of switch, and watchdog timer selection etc.
3.1 Before Installation
After confirming your package contents, you are now ready to install
your hardware. The following are important reminders and steps to
take before you begin with your installation process.
1. Make sure that all jumper settings match their default settings
and CMOS setup correctly. Refer to the sections on this chapter
for the default settings of each jumper. (JP1 short 1-2)
2. Go through the connections of all external devices and make
sure that they are installed properly and configured correctly
within the CMOS setup. Refer to the sections on this chapter
for the detailed information on the connectors.
3. Keep the driver CD in good condition for future reference and
use.
Page 14
8
3.2 Board Layout
Page 15
9
3.3 Jumper List
Jumper Default Setting Setting Page
JP1 Clear CMOS: Keep CMOS Short 1-2 15
JP5 Panel Voltage Select: +3.3V Short 2-3 10
JP6 Short 1-2 10
JP7 Short 1-2 10
JP8
FSB Frequency Select: CPU Driven
Short 2-3 10
JP10 Short 1-2 10
JP11
Onboard Display or External PCIex16 Bus
Select: CRT Function
x 10
CN3
COM2 Use RS-232 or RS-422/485 Select:
RS-232
Open 13
3.4 Connector List
Connector Definition Page
CN1 RS-422/485 Connector (3x2 header) 13
CN2 8-bit GPIO 20
CN5/CN6/CN7/CN8 COM 1~COM 4 Connector 13
CN9 Parallel Port 16
CN10/CN11 DDRII Socket 10
CN13/CN12 LVDS Panel Connector 10
CN14/CN15/CN16 Serial ATA Connector 13
CN17 MIC In/Line Out Connector 20
CN18 System Front Panel Connector 17
CN19/CN20 RJ-45 Connector 14
CN21 6-pin KB/MS Connector 17
CN23 DVI-I Connector 10
CN24/CN25/CN29 Internal USB2.0 Ports 15
CN26 15-pin CRT Connector 10
CN27 CompactFlash Socket 21
CN28 External USB2.0 Port 15
FN1/FN2 CPU Fan Power Connector 16
JP4 Inverter Power Connector 10
Page 16
10
3.5 Configuring the CPU
The HS-7322 uses Socket P for Intel® Mobile Dual-Core processors,
supports 1066/800/667MHz FSB.
z JP6/JP7/JP8: FSB Frequency Select
Settings
Options
JP6 JP7 JP8
CPU Driven (default) Short 1-2 Short 1-2 Short 2-3
1066MHz FSB Open Short 2-3 Short 2-3
800MHz FSB Open Open Short 2-3
667MHz FSB Short 2-3 Open Short 2-3
13
13
13
3.6 System Memory
The HS-7322 provides two 240-pin DIMM sockets at locations
CN10/CN11. It supports DDR2 up to 4GB SDRAM.
3.7 VGA Controller
The HS-7322 provides two connection methods of a VGA device.
CN26 is a 15-pin CRT connector, CN23 is DVI-I connector, and
CN13/CN12 are the LVDS interface connectors onboard reserved for
flat panel installation.
z JP10/JP11: Onboard Display or External PCIe x16 Bus Select
CRT Version
Settings
Options
JP10 JP11
CRT Function (default) Short 1-2 x
External PCIe x16 Short 2-3 x
13
Page 17
11
DVI-I Version
Settings
Options
JP10 JP11
DVI-I Function (default) Short 1-2 Open
External PCIe x16 Short 2-3 Short
13
z CN26: 15-pin CRT Connector
PIN Description PIN Description
1 Red 2 Green
3 Blue 4 N/C
5 GND 6 GND
7 GND 8 GND
9 VCC 10 GND
11 N/C 12 DDCDA
13 HSYNC 14 VSYNC
15 DDCCL
1
7123914
5
611281341015
z CN13/CN12: LVDS Interface Connector
PIN Description PIN Description
1 V
LCD
2 V
LCD
3 GND 4 GND
5 A0-/B0- 6 A0+/B0+
7 A1-/B1- 8 A1+/B1+
9 A2-/B2- 10 A2+/B2+
11 CLK1-/CLK2- 12 CLK1+/CLK2+
13 A3-/B3- 14 A3+/B3+
12
13 14
NOTE: LVDS cable should be produced very carefully. A0- & A0+ have to
be fabricated in twister pair (A1- & A1+, A2- & A2+ and so on)
otherwise the signal won’t be stable. Please set the proper voltage
of your panel using JP4 before proceeding on installing it.
Page 18
12
z JP4: Inverter Power Connector
PIN Description
1 +12V
2 +12V
3 VCC5
4 BK_EN
5 LCD_EN
6 GND
1
6
NOTE: If use CN13 only, it just supports 24-bit single channel LVDS
panel; If you want to use 48-bit dual channel LVDS panel, please
use CN13 and CN12 combined.
The HS-7322 has an onboard jumper that selects the working voltage
of the flat panel connected to the system. Jumper JP5 offers two
voltage settings for the user.
z JP5: Panel Voltage Select
Options Settings
+3.3V (default) Short 2-3
+5V Short 1-2
1
3
z CN23: DVI-I Connector
PIN Description PIN Description
1 - DATA2 2 DATA2
3 GND 4 N/C
5 N/C 6 DDCCLK
7 DDCDATA 8 VSYNC
9 -DATA1 10 DATA1
11 GND 12 N/C
13 N/C 14 VCC5
15 GND 16 HPDET
17 -DATA0 18 DATA0
19 GND 20 N/C
21 N/C 22 GND
23 CLK 24 -CLK
25 RED 26 GREEN
27 BLUE 28 HSYNC
29 GND 30 GND
117
9
824
16
26 28
29 30
25 27
Page 19
13
3.8 Serial ATA Connector
You can connect the Serial ATA device that provides you high speeds
transfer rates (300MB/sec.).
z CN14/CN15/CN16: Serial ATA Connector
PIN Description
1 GND
2 SATATXP
3 SATATXN
4 GND
5 SATARXN
6 SATARXP
7 GND
17
3.9 Serial Port Connectors
The HS-7322 offers 16C550 compatible UARTs with Send/
Receive 16-byte FIFO serial ports.
z CN5~CN8: COM 1 ~ COM 4 Connector (5x2 Header)
PIN Description PIN Description
1 DCD 2 DSR
3 RXD 4 RTS
5 TXD 6 CTS
7 DTR 8 RI
9 GND 10 Don’t Use
19
10 2
z CN1: RS-422/485 Connector (3x2 Header, COM 2)
PIN Description PIN Description
1 TX- 2 TX+
3 RX+ 4 RX-
5 GND 6 VCC
15
62
NOTE: The terminal resistance of RX & TX is set at 180Ω.
Page 20
14
z CN3: COM 2 use RS-232 or RS-422/485 Select
Options Settings
RS-232 (default) Open
RS-485 Transmit Only (*1) Short 1-2, 3-4, 5-7, 8-10
RS-485 by –RTS (*-1) Short 1-2, 3-4, 7-9, 8-10
RS-422/485 Full Duplex (*2) Short 1-2, 3-4, 6-8
19
10 2
NOTE: *1: 2-wires RS-485 function
*2: 4-wires point-to-point full duplex function
4-wires point-to-point full duplex RS-422/485
Typical RS-485 2-wires Mutildrop Network
3.10 Ethernet Connector
The HS-7322 provides two RJ-45 connectors for 10/100/1000 Based
LAN. Please refer to the following for its pin information.
When installs OS, this driver namely can automatically install. User
does not need to renewal.
z CN19/CN20: RJ-45 Connector
PIN Description PIN Description
1 MDIP0 2 MDIN0
3 MDIP1 4 MDIN1
5 MDIP2 6 MDIN2
7 MDIP3 8 MDIN3
Page 21
15
3.11 USB Port
The HS-7322 provides one 8-pin connector, at location
CN24/CN25/CN29, and CN28 is external USB2.0 port, there are total
seven USB2.0 ports in HS-7322.
z CN28: External USB2.0 Port
PIN Description
1 VCC
2 BD7-
3 BD7+
4 GND
z CN24/CN25/CN29: Internal USB2.0 Connector
PIN Description PIN Description
1 VCC 2 VCC
3 USBD1-/3-/5- 4 USBD2-/4-/6-
5 USBD1+/3+/5+ 6 USBD2+/4+/6+
7 GND 8 GND
1
2
78
3.12 CMOS Data Clear
The HS-7322 has a Clear CMOS jumper on JP1.
z JP1: Clear CMOS
Options Settings
Normal Operation (default) Short 1-2
Clear CMOS Short 2-3
13
IMPORTANT: Before turn on the power of system, please set JP1 to
open for normal operation.
Page 22
16
3.13 Parallel Port
CN9 is a standard 26-pin flat cable connector designed to
accommodate parallel port connection onboard the HS-7322.
z CN9: Parallel Port
PIN Description PIN Description
1 Strobe 14 Auto From Feed
2 DATA 0 15 ERROR#
3 DATA 1 16 Initialize
4 DATA 2 17 Printer Select LN#
5 DATA 3 18 GND
6 DATA 4 19 GND
7 DATA 5 20 GND
8 DATA 6 21 GND
9 DATA 7 22 GND
10 Acknowledge 23 GND
11 Busy 24 GND
12 Paper Empty 25 GND
13 Printer Select 26 GND
13
1
2614
3.14 Power and Fan Connectors
HS-7322 provides Connector FN2 onboard HS-7322 is a 3-pin +12V
fan power output connector.
z FN1/FN2: Fan Power Connector
PIN Description
1 GND
2 +12V
3 Fan In
13
Page 23
17
3.15 Keyboard/Mouse Connectors
The CN21 is an internal 6-pin connector for HS-7322.
z CN21: Internal 6-pin Keyboard/Mouse Connector
PIN Description
1 Keyboard Data
2 Mouse Data
3 GND
4 +5V
5 Keyboard Clock
6 Mouse Clock
16
3.16 System Front Panel Control
The HS-7322 has front panel control at location CN18.
z CN18: System Front Panel Control
PIN Description PIN Description
1 220Ω pull VCC 2 Speaker
3 HDD LED 4 N/C
5 GND 6 200Ω pull VCC
7 ATX Power Button 8 200Ω pull VCC
9 Reset Switch 10 200Ω pull VCC
11 GND 12 GND
Connector CN18 Orientation
1
3
5
7
9
11
2
4
6
8
10
12
Speaker
ATX
Power
LED
Reset
Button
HDD LED
ATX Power
Button
Page 24
18
3.17 Watchdog Timer
Once the Enable cycle is active a Refresh cycle is requested before the
time-out period. This restarts counting of the WDT period. When the
time counting goes over the period preset of WDT, it will assume that
the program operation is abnormal. A reset system signal will restart
when such error happens.
The HS-7322 custom WDT circuit is implemented using the internal IO
of the Winbond Super I/O W83627UHG which is at 2Eh of LPC.
The following sample programs show how to enable, disable and
refresh the watchdog timer:
Sample Code
C Language for Watchdog Timer under DOS.
#include<stdio.h>
#include<dos.h>
static unsigned int 83627UHG_Port = 0x2e;
{
Outportb(83627UHG_Port,0x87);
Outportb(83627UHG_Port,0x87);
}
void W83627UHG_WDT(unsigned int count_setup)
{
unsigned int Counting, Register_Setup;
outportb(83627UHG_Port, 0x07);
outportb(83627UHG_Port+1, 8); // set as Logical
Device 8
if(count_value >= 60)
{
outportb(83627UHG_Port, 0xf5);
Register_Setup = inportb(83627UHG_Port+1);
Register_Setup |= 0x08;
outportb(83627UHG_Port+1, Register_Setup); /
/ set as minute mode
counting = count_setup / 60;
if((count_value%60) > 30)
Page 25
19
counting++;
if(counting > 255)
counting = 255;
printf("WDT timeout in %d minutes.\n",
counting);
}
else
{
outportb(83627UHG_Port, 0xf5);
Register_Setup = inportb(83627UHG_Port+1);
Register_Setup &= 0xf7;
outportb(83627UHG_Port+1, Register_Setup); /
/ set as second mode
Counting = count_setup;
printf("WDT timeout in %d seconds.\n",
counting);
}
If(counting)
{
outportb(83627UHG_Port, 0x30);
Register_Setup = inportb(83627UHG_Port+1);
Register_Setup |= 0x01;
outportb(83627UHG_Port+1, Register_Setup);// set WDTO#
active
outportb(83627UHG_Port, 0x07);
outportb(83627UHG_Port+1, 8); // set as Logical
Device 8
outportb(83627UHG_Port, 0xf6);
outportb(83627UHG_Port+1, counting); // set WDT
count value
};
Page 26
20
3.18 Audio Connectors
The HS-7322 has an onboard RealTek ALC262 audio connector. The
following tables list the pin assignments of the MIC In/Line Out
connector.
z CN17: MIC In/Line Out Connector
PIN Description PIN Description
1 AOUTL 2 AOUTR
3 GND 4 GND
5 MIC IN L 6 MIC IN R
7 GND 8 GND
12
78
3.19 8-bit GPIO Function
The HS-7322 offers one 8-bit input/output port.
z CN2: 8-bit GPIO
PIN Description PIN Description
1 VCC 2 GND
3 GD0 4 GD4
5 GD1 6 GD5
7 GD2 8 GD6
9 GD3 10 GD7
19
10 2
EX. Sample Code Using GPIO 5
#include <conio.h>
#include <stdio.h>
#include <io.h>
void main(void)
{
unsigned char byte_cr29;
outportb(0x2e, 0x87); // enter Super I/O configuration mode
outportb(0x2e, 0x87);
outportb(0x2e,0x29); // set CR29 bit 5
byte_cr29 = (inportb(0x2f) | 0x20); // to switch UARTA to GPIO5
outportb(0x2f, byte_cr29);
outportb(0x2e, 0x07); // locate logical device 8
outportb(0x2e, 0x08);
outportb(0x2e, 0x30); // set CR30 bit 1 (enable GPIO5)
Page 27
21
outportb(0x2f, 0x02);
outportb(0x2e, 0xe0); // set GP54 ~ GP57
outportb(0x2f, 0x0F); // GP54 ~ GP57 as output pins
}
3.20 CompactFlash Socket
The HS-7322 also offers a Type I/II CompactFlash socket is IDE
interface located at the solder side of the board. The designated CN27,
once soldered with an adapter, can hold CompactFlash cards of
various sizes. Please turn off the power before inserting the CF card.
Inserting a CompactFlash card into the adapter is not a difficult task.
The socket and card are both keyed and there is only one direction for
the card to be completely inserted. Refer to the diagram on the
following page for the traditional way of inserting the card.
Page 28
22
z CN27: CompactFlash Socket
PIN Description PIN Description
1 GND 2 DATA3
3 DATA4 4 DATA5
5 DATA6 6 DATA7
7 SDCS1# 8 GND
9 GND 10 GND
11 GND 12 GND
13 VCC 14 GND
15 GND 16 GND
17 GND 18 SDA2
19 SDA1 20 SDA0
21 DATA0 22 DATA1
23 DATA2 24 470Ω pull GND
25 N/C 26 N/C
27 DATA11 28 DATA12
29 DATA13 30 DATA14
31 DATA15 32 SDCS3#
33 N/C 34 UOR
35 IOW 36 EWE0
37 IRQ 38 VCC
39 CS 40 N/C
41 RESET 42 IORDY
43 DACK 44 REQ
45 IDE LED 46 PDIAG
47 DATA8 48 DATA9
49 DATA10 50 GND
NOTE: When use CF card, IDE device function will be disabled.
Page 29
23
Chapter 4
AMI BIOS Setup
The HS-7321 uses AMI BIOS for the system configuration. The AMI
BIOS setup program is designed to provide the maximum flexibility in
configuring the system by offering various options that could be
selected for end-user requirements. This chapter is written to assist
you in the proper usage of these features.
4.1 Starting Setup
The AMI BIOS is immediately activated when you first power on the
computer. The BIOS reads the system information contained in the
CMOS and begins the process of checking out the system and
configuring it. When it finishes, the BIOS will seek an operating system
on one of the disks and then launch and turn control over to the
operating system.
While the BIOS is in control, the Setup program can be activated in one
of two ways:
1. By pressing <Del> immediately after switching the system on, or
2. By pressing the <Del> key when the following message appears
briefly at the bottom of the screen during the POST (Power On Self
Test).
Press DEL to enter SETUP.
If the message disappears before you respond and you still wish to
enter Setup, restart the system to try again by turning it OFF then ON or
pressing the "RESET" button on the system case. You may also restart
by simultaneously pressing <Ctrl>, <Alt>, and <Delete> keys. If you do
not press the keys at the correct time and the system does not boot, an
error message will be displayed and you will be asked to...
PRESS F1 TO CONTINUE, DEL TO ENTER SETUP
Page 30
24
4.2 Using Setup
In general, you use the arrow keys to highlight items, press <Enter> to
select, use the <PageUp> and <PageDown> keys to change entries,
and press <Esc> to quit. The following table provides more detail about
how to navigate in the Setup program using the keyboard.
↑ Move to previous item
↓ Move to next item
← Move to previous item
→ Move to previous item
Esc key Main Menu -- Quit and not save changes into CMOS
Status Page Setup Menu and Option Page Setup Menu -Exit current page and return to Main Menu
PgUp key Decrease the numeric value or make changes
PgDn key Increase the numeric value or make changes
+ key Increase the numeric value or make changes
- key Decrease the numeric value or make changes
F1 key Reserved
F2 key Change color from total 8 colors. F2 to select color forward
F3 key F2 to select color backward
F4 key Reserved
F5 key Reserved
F6 key Reserved
F7 key Reserved
F8 key Reserved
F9 key Reserved
F10 key Save all the CMOS changes, only for Main Menu
Page 31
25
4.3 Main Menu
Once you enter the AMI BIOS CMOS Setup Utility, the Main Menu will
appear on the screen. The Main Menu allows you to select from several
setup functions and two exit choices. Use the arrow keys to select
among the items and press <Enter> to enter the sub-menu.
BIOS SETUP UTILITY
Main Advanced PCIPnP Boot Security Chipset Exit
System Overview
AMIBIOS
Version : 08.00.15
Build Date : 06/22/09
ID : A7322004
Processor
Type
Intel(R) Core(TM) 2 Duo CPU T7500 @ 2.20GHz
Speed : 2200MHz
Count : 1
System Memory
Size : 893MB
Select Screen
Select Item
System Time [00:29:32] ª -
Change Field
System Date [Tue 01/01/2002] Tab Select Field
F1 General Help
F10 Save and Exit
ESC Exit
v02.59 (C)Copyright 1985-2005, American Megatrends, Inc.
NOTE: A brief description of the highlighted choice appears at the bottom
of the screen.
Page 32
26
4.4 Advanced Settings
This section allows you to configure your system for the basic
operation. You have the opportunity to select the system’s default
speed, boot-up sequence, keyboard operation, shadowing and
security.
BIOS SETUP UTILITY
Main Advanced PCIPnP Boot Security Chipset Exit
Advanced Settings
WARNING: Setting wrong values in below sections
may cause system to malfunction.
CPU Configuration
IDE Configuration
Floppy Configuration
Select Screen
SuperIO Configuration
Select Item
Hardware Health Configuration ª - Change Field
ACPI Configuration Tab Select Field
USB Configuration F1 General Help
F10 Save and Exit
ESC Exit
v02.59 (C)Copyright 1985-2005, American Megatrends, Inc.
BIOS SETUP UTILITY
Main Advanced PCIPnP Boot Security Chipset Exit
Configure advanced CPU settings
Module Version –13.03
Manufacturer : Intel
Intel(R) Core(TM) 2 Duo CPU T7500 @ 2.20GHz
Frequency : 2.20GHz
FSB Speed : 800MHz
Cache L1 : 32 KB
Cache L2 : 4096 KB
Ratio Actual Value : 11
Select Screen
Select Item
Max CPUID Value Limit [Disabled] ª - Change Field
Intel(R) Virtualization Tech [Enabled] Tab Select Field
Execute-Disabled Bit Capability [Enabled] F1 General Help
Hyper Threading Technology [Enabled] F10 Save and Exit
Intel(R) SpeedStep(TM) tech [Enabled] ESC Exit
v02.59 (C)Copyright 1985-2005, American Megatrends, Inc.
Page 33
27
BIOS SETUP UTILITY
Main Advanced PCIPnP Boot Security Chipset Exit
IDE Configuration
SATA PORT0 : [Not Detected]
SATA PORT1 : [Not Detected]
SATA PORT2 : [Not Detected]
Select Screen
SATA PORT3 : [Not Detected]
Select Item
ª - Change Field
Tab Select Field
F1 General Help
F10 Save and Exit
ESC Exit
v02.59 (C)Copyright 1985-2005, American Megatrends, Inc.
BIOS SETUP UTILITY
Main Advanced PCIPnP Boot Security Chipset Exit
Floppy Configuration
Floppy A [Disabled]
Select Screen
Select Item
ª - Change Field
Tab Select Field
F1 General Help
F10 Save and Exit
ESC Exit
v02.59 (C)Copyright 1985-2005, American Megatrends, Inc.
BIOS SETUP UTILITY
Main Advanced PCIPnP Boot Security Chipset Exit
Configure WIN627EHF Super IO Chipset
OnBoard Floppy Controller [Enabled]
Serial Port1 Address [3F8]
Serial Port2 Address [2F8]
Serial Port2 Mode [Normal]
Serial Port3 Address [3E8]
Serial Port4 Address [2E8]
Select Item
Parallel Port Address [378] ª - Change Field
Parallel Port Mode [Normal] Tab Select Field
F1 General Help
F10 Save and Exit
ESC Exit
v02.59 (C)Copyright 1985-2005, American Megatrends, Inc.
Page 34
28
BIOS SETUP UTILITY
Main Advanced PCIPnP Boot Security Chipset Exit
Hardware Health Configuration
CPU Temperature :
System Temperature :
CPUFAN Speed :
:
Select Screen
Vcore :
Select Item
12V : ª - Change Field
3.3V : Tab Select Field
1.8V : F1 General Help
: F10 Save and Exit
ESC Exit
v02.59 (C)Copyright 1985-2005, American Megatrends, Inc.
BIOS SETUP UTILITY
Main Advanced PCIPnP Boot Security Chipset Exit
ACPI Settings
Suspend mode [Auto]
Select Screen
Select Item
ª - Change Field
Tab Select Field
F1 General Help
F10 Save and Exit
ESC Exit
v02.59 (C)Copyright 1985-2005, American Megatrends, Inc.
BIOS SETUP UTILITY
Main Advanced PCIPnP Boot Security Chipset Exit
USB Configuration
Legacy USB Support [Enabled]
Select Screen
USB 2.0 Controller Mode [HiSpeed]
Select Item
ª - Change Field
Tab Select Field
F1 General Help
F10 Save and Exit
ESC Exit
v02.59 (C)Copyright 1985-2005, American Megatrends, Inc.
Page 35
29
4.5 Advanced PCI/PnP Settings
This section describes configuring the PCI bus system. PCI, or
Personal Computer Interconnect, is a system that allows I/O devices to
operate at speeds nearing the speed the CPU itself uses when
communicating with its own special components. This section covers
some very technical items and it is strongly recommended that only
experienced users should make any changes to the default settings.
BIOS SETUP UTILITY
Main Advanced PCIPnP Boot Security Chipset Exit
Advanced PCI/PnP Settings
WARNING: Setting wrong values in below
sections may cause system to
malfunction.
Clean NVRAM [No]
Plug & Play O/S [Yes]
HDA Controller [Enabled]
Onboard Lan1 Controller [Enabled]
Onboard Lan2 Controller [Enabled]
Onboard Lan Boot ROM [Enabled]
TPM Controller [Enabled]
Trusted Computing
Watch Dog Timer Select [Disabled]
Restore on AC Power Loss [Last State]
Select Screen
Select Item
ª - Change Field
Tab Select Field
F1 General Help
F10 Save and Exit
ESC Exit
v02.59 (C)Copyright 1985-2005, American Megatrends, Inc.
Page 36
30
4.6 Boot Settings
BIOS SETUP UTILITY
Main Advanced PCIPnP Boot Security Chipset Exit
Boot Settings
Boot Device Priority
Hard Disk Drives
Removable Drivers
Select Screen
Select Item
ª - Change Field
Tab Select Field
F1 General Help
F10 Save and Exit
ESC Exit
v02.59 (C)Copyright 1985-2005, American Megatrends, Inc.
BIOS SETUP UTILITY
Main Advanced PCIPnP Boot Security Chipset Exit
Boot Device Priority
1st Boot Device [SATA:PM-ST34313A]
2nd Boot Device [Network: Realtek Bo]
Select Screen
3rd Boot Device [Network: Realtek Bo]
Select Item
4th Boot Device [Disabled] ª - Change Field
Try Other boot Device [Yes] Tab Select Field
F1 General Help
F10 Save and Exit
ESC Exit
v02.59 (C)Copyright 1985-2005, American Megatrends, Inc.
BIOS SETUP UTILITY
Main Advanced PCIPnP Boot Security Chipset Exit
Hard disk Drives
1st Drive [SATA:PM-ST34313A]
Select Screen
Select Item
ª - Change Field
Tab Select Field
F1 General Help
F10 Save and Exit
ESC Exit
v02.59 (C)Copyright 1985-2005, American Megatrends, Inc.
Page 37
31
BIOS SETUP UTILITY
Main Advanced PCIPnP Boot Security Chipset Exit
Removable Drives
1st Drive [Disabled]
Select Screen
Select Item
ª - Change Field
Tab Select Field
F1 General Help
F10 Save and Exit
ESC Exit
v02.59 (C)Copyright 1985-2005, American Megatrends, Inc.
4.7 Security Settings
BIOS SETUP UTILITY
Main Advanced PCIPnP Boot Security Chipset Exit
Security Settings
Supervisor Password : Not Installed
User Password : Not Installed
Select Screen
Change Supervisor Password
Select Item
Change User Password ª - Change Field
Boot Sector Virus Protection [Disabled] Tab Select Field
F1 General Help
F10 Save and Exit
ESC Exit
v02.59 (C)Copyright 1985-2005, American Megatrends, Inc.
Page 38
32
4.8 Advanced Chipset Settings
BIOS SETUP UTILITY
Main Advanced PCIPnP Boot Security Chipset Exit
Advanced Chipset Settings
WARNING: Setting wrong values in below
sections may cause system to
malfunction.
North Bridge Configuration
Select Screen
South Bridge Configuration
Select Item
ª - Change Field
Tab Select Field
F1 General Help
F10 Save and Exit
ESC Exit
v02.59 (C)Copyright 1985-2005, American Megatrends, Inc.
BIOS SETUP UTILITY
Main Advanced PCIPnP Boot Security Chipset Exit
North Bridge Chipset Configuration
Boots Graphic Adapter Priority [PEG/PCI]
Internal Graphics Mode Select [Enabled, 128MB]
PAVP Mode [Lite]
PEG Port Configuration
Select Screen
PEG Port [Auto]
Select Item
ª - Change Field
DVMT Mode Select [DVMT Mode] Tab Select Field
DVMT/FIXED Memory [256MB] F1 General Help
Boot Display Device [VBIOS-Default] F10 Save and Exit
Flat Panel Type [Type 3] ESC Exit
v02.59 (C)Copyright 1985-2005, American Megatrends, Inc.
Flat Panel Type
Type 1 640 x 480 18-bit Single Channel
Type 2 800 x 600 18-bit Single Channel
Type 3 1024 x 768 24-bit Single Channel
Type 4 1280 x 1024 24-bit Dual Channel
Type 5 1400 x 1050 24-bit Dual Channel
Type 6 1600 x 1200 24-bit Dual channel
Page 39
33
BIOS SETUP UTILITY
Main Advanced PCIPnP Boot Security Chipset Exit
Sorth Bridge Chipset Configuration
PCIE Ports Configuration
PCIE Port 0 [Auto]
PCIE Port 1 [Auto]
Select Screen
PCIE Port 2 [Auto]
Select Item
PCIE Port 3 [Auto] ª - Change Field
PCIE Port 4 [Auto] Tab Select Field
PCIE Port 5 [Auto] F1 General Help
F10 Save and Exit
ESC Exit
v02.59 (C)Copyright 1985-2005, American Megatrends, Inc.
4.9 Exit Options
BIOS SETUP UTILITY
Main Advanced PCIPnP Boot Security Chipset Exit
Exit Options
Save Changes and Exit
Discard Changes and Exit
Discard Changes
Load Optimal Defaults
Load Failsafe Defaults
Select Screen
Select Item
ª - Change Field
Tab Select Field
F1 General Help
F10 Save and Exit
ESC Exit
v02.59 (C)Copyright 1985-2005, American Megatrends, Inc.
Page 40
34
This is the blank page.
Page 41
35
Chapter 5
Software Utilities
This chapter contains the detailed information about installation
procedures of chipset, VGA, LAN, audio and other drivers. The utility
CD disk that comes with the package contains an auto-run program
that invokes the installation programs for the chipset, VGA, LAN and
audio drivers. The following sections describe the installation
procedures of each driver based on WinXP operating systems. Other
operation system may be slightly different.
5.1 Chipset Driver Installation
1. Insert the CD that comes with the board into the CD-ROM drive.
Click CHIPSET to install chipset driver.
Page 42
36
2. Immediately after clicking the CHIPSET button in Step 1, the
program launches the Setup that will assist you in the
installation process. Click on the N
ext > button to proceed.
3. The License Agreement dialog box then appears on the screen.
Choose Y
es to proceed.
Page 43
37
4. When the Readme File Information dialog box pops up, just
clock on the Next> button to proceed.
5. Click on the Finish to completed the installation.
Page 44
38
5.2 VGA Driver Installation
1. Insert the CD that comes with the board into the CD-ROM drive.
Click VGA to install Intel® GM45 video driver.
2. The Welcome to the Setup program dialog box appears on the
screen. Choose Next> to proceed.
Page 45
39
3. The Intel® License Agreement dialog box appears on the screen.
Choose Y
es to proceed.
4. When the Readme File Information dialog box pops up, just click
on the Next> button to proceed.
Page 46
40
5. The Installshield Wizard dialog box appears on the screen. Click
on Next> to proceed.
6. When Setup Progress finished, just click on Next button to
proceed.
Page 47
41
7. Please select “Yes, I want to restart my computer now”
button then click “F
inish” to reboot your system to take the
effect once the installation is completed.
5.3 LAN Driver Installation
1. Insert the CD that comes with the board into the CD-ROM drive.
Click LAN to install RTL8111 LAN driver.
Page 48
42
2. When the dialog box below appears, make sure you close all
other Windows applications the click on the N
ext> button to
proceed.
3. The Setup Status dialog box then appears on the screen.
Page 49
43
4. When setup is finished, please reboot your computer to take the
effect.
5.4 Audio Driver Installation
1. Insert the CD that comes with the board into the CD-ROM drive.
Click Audio to install audio driver.
Page 50
44
2. When the dialog box below appears, Click on Yes to proceed.
3. Please select “Yes, I want to restart my computer now”
button then click “F
inish” to reboot your system to take the
effect once the installation is completed.
Loading...