Boser HS-4701 User Manual

HS-4701

Pentium® 4 Embedded

Engine Board

Mini AGP•DDR•PCI Slot•DIO•

•

•CRT/LVDS Panel•TV-Out•

LAN•Audio•ATA/33/66/100•

•

•RS-232/422/485•4COM•USB2.0•

WDT•H/W Monitor•

•

Copyright Disclaimers

The accuracy of contents in this manual has passed thorough checking and review before
publishing. BOSER Technology Co., Ltd., the manufacturer and publisher, is not liable for
any infringements of patents or other rights resulting from its use. The

not be responsible for any direct, indirect, special, incidental or consequential
damages arising from the use of this product or documentation, even if advised of
the possibility of such damage(s).

This manual is copyrighted and BOSER Technology Co., Ltd. reserves all
documentation rights. Unauthorized reproduction, transmission, translation, and
storage of any form and means (i.e.,

this document, in whole or partly, is prohibited, unless granted permission by BOSER
Technology Co., Ltd.

BOSER Technology Co., Ltd.

this document without due notice.
responsibility for any errors or omissions that may appear in this manual, nor does
it make any commitment to update the information contained herein.

T

r

a

d

e

m

T

r

T

r

BOSER is a registered trademark of BOSER Technology Co., Ltd.
ISB is a registered trademark of BOSER Technology Co., Ltd.
Intel is a registered trademark of Intel Corporation.
AMI is a registered trademark of AMI Software, Inc.
All other trademarks, products and or product names mentioned herein are

mentioned for identification purposes only, and may be trademarks and/or registered
trademarks of their respective companies or owners.

a

a

d

e

m

a

a

d

e

m

a

reserves the right to change or improve the contents of

r

k

s

r

k

s

r

k

s

electronic, mechanical, photocopying, recording) of

BOSER Technology Co., Ltd. assumes no

manufacturer will

© Copyright 2003 BOSER Technology Co., Ltd.

All Rights Reserved.
Edition 1.3, October 19, 2004

Table of Contents

Chapter 1 General Description………………………1

1.1 Major Features....................................................................2

1.2 Specifications .....................................................................3

1.3 Board Dimensions..............................................................4

Chapter 2 Unpacking…………………………………5

2.1 Opening the Delivery Package..........................................5

2.2 Inspection............................................................................5

Chapter 3 Hardware Installation……………………7

3.1 Before Installation ..............................................................7

3.2 Board Layout ......................................................................8

3.3 Jumper List .........................................................................9

3.4 Connector List ....................................................................9

3.5 Configuring the CPU ........................................................10

3.6 System Memory................................................................10

3.7 VGA Controller .................................................................10

3.8 PCI E-IDE Drive Connector..............................................11

3.9 Floppy Disk Drive Connector ..........................................14

3.10 Serial Port Connectors ....................................................15

3.11 Parallel Connector............................................................16

3.12 Ethernet Connector..........................................................17

3.13 USB Connector.................................................................17

3.14 CMOS Data Clear..............................................................18

3.15 Power and Fan Connectors.............................................18

3.16 Keyboard/Mouse Connectors .........................................19

3.17 System Front Panel Connectors.....................................19

3.18 External Speaker ..............................................................20

3.19 Audio Connectors ............................................................20

3.20 Digital Input/Output..........................................................21

3.21 TV Out Function ...............................................................22

3.22 Mini AGP Connector ........................................................22

3.23 PCI Expansion Slot ..........................................................22

Chapter 4 Award BIOS Setup……………………...23

4.1 Starting Setup...................................................................23

4.2 Using Setup ......................................................................24

4.3 Main Menu.........................................................................25

4.4 Standard CMOS Setup.....................................................26

4.5 Advanced CMOS Setup ...................................................27

4.6 Advanced Chipset Setup.................................................28

4.7 Power Management Setup ..............................................29

4.8 PCI / Plug and Play Setup................................................30

4.9 Peripheral Setup...............................................................31

4.10 PC Health Status ..............................................................32

4.11 Frequency/Voltage Control .............................................32

Chapter 5 Software Utilities………………………..33

5.1 IDE Driver Installation......................................................33

5.2 VGA Driver Installation....................................................38

5.3 LAN Driver Installation ....................................................46

5.4 Audio Driver Installation..................................................55

Safety Instructions

Integrated circuits on computer boards are sensitive to static electricity. To
avoid damaging chips from electrostatic discharge, observe the following
precautions:



Do not remove boards or integrated circuits from their anti-static packaging
until you are ready to install them.

 Before handling a board or integrated circuit, touch an unpainted portion of the

system unit chassis for a few seconds. This helps to discharge any static
electricity on your body.



Wear a wrist-grounding strap, available from most electronic component
stores, when handling boards and components. Fasten the ALLIGATOR clip
of the strap to the end of the shielded wire lead from a grounded object.
Please wear and connect the strap before handle the HS-4701 to ensure
harmlessly discharge any static electricity through the strap.



Please use an anti-static pad when putting down any components or parts or
tools outside the computer. You may also use an anti-static bag instead of the
pad. Please inquire from your local supplier for additional assistance in finding
the necessary anti-static gadgets.

NOTE:

DO NOT TOUCH THE BOARD OR ANY OTHER SENSITIVE
COMPONENTS WITHOUT ALL NECESSARY ANTI-STATIC
PROTECTION.

This Page is intentionally left blank.

Chapter 1

General Description

The HS-4701 is an Intel® 82845GE/82801DB chipset-based board
designed for PCI Bus PGA 478 Intel

2.4GHz(400MHz FSB)/3.06GHz(533MHz FSB) CPU compatibility.
These features combine and make the HS-4701 an ideal all-in-one
industrial single board computer. Additional features include an
enhanced I/O with CRT/LVDS Panel, DIO, LAN, Audio and 4COM
ports interface.

®

Pentium® 4 up to

Its onboard ATA/33/66/100 to IDE drive interface architecture allows
the HS-4701 to support data transfers of 33, 66 or 100MB/sec. to each
IDE drive connection. Designed with the Intel
core logic chipset, the board supports all PGA 478 Pentium® 4 CPU
series operating up to 2.4GHz(400MHz FSB)/3.06GHz(533MHz FSB).
The display controller is Intel
supporting CRT display up to 1280 x 1024 at 32-bit colors, it also
provides LVDS panel interface.

System memory is also sufficient with the two DDR sockets that can
support up to 2GB.

Additional onboard connectors include an advanced USB2.0 port
providing faster data transmission, and one internal 5x2 connector for
10/100 Base-TX Ethernet use.

®

82845GE with 1MB or 8MB memory

®

82845GE/82801DB

1

1.1 Major Features

The HS-4701 comes with the following features:

 PGA 478 for Intel® Pentium® 4 up to 2.4GHz(400MHz FSB)/

3.06GHz(533MHz FSB) CPU

 Intel
 Two DDR sockets with a max. capacity of 2GB
 Winbond W83627, SMC SP37E760 super I/O chipset
 Fast PCI ATA/33/66/100 IDE controller
 Three RS-232 and one RS-232/422/485 serial ports
 Intel 82845GE CRT display controller
 Supports LVDS Panel interface
 Intel 82562 10/100 Based LAN

 Supports USB2.0, two connectors
 Supports Hardware Monitor function
 Supports 16-bit Digital Input/Output function (optional)
 Supports TV-Out function (optional)

®

82845GE/82801DB system chipset

AC97 3D audio controller

2

1.2 Specifications



CPU: PGA 478 for Intel® Pentium® 4 up to 2.4GHz(400MHz FSB)/

3.06GHz(533MHz FSB)

 Bus Interface: PCI and Mini AGP Bus
 Memory: Two DDR sockets supporting up to 2GB
 Chipset: Intel

®

82845GE/82801DB

 I/O Chipset: Winbond W83627, SMC SP37E760
 PCI Slot:
 Digital I/O:

One standard PCI slot

16-bit Digital Input/Output port (optional)

 VGA: Intel 82845GE with 1MB or 8MB memory supporting CRT display

up to 1280 x 1024 at 32-bit colors



Panel Display: Supports LVDS Panel interface



IDE: Four IDE disk drives supporting ATA/33/66/100 and with transfer
rates of up to 33/66/100MB/sec.

 FDD: Supports up to two floppy disk drives
 Parallel: One enhanced bi-directional parallel port supporting

SPP/ECP/EPP



LAN: Intel® 82562 10/100 Based LAN



Audio: AC97 3D audio controller



Serial Port: 16C550 UART-compatible RS-232/422/485 x 1 and RS-232
x 3 serial ports with 16-byte FIFO

 USB: Supports USB2.0, two connectors
 TV-

Out: Supports PAL or NTSC TV systems (optional)

 Keyboard/Mouse: 8-pin connector supporting standard PC/AT

keyboard and PS/2 mouse



BIOS: Award PnP Flash BIOS



Watchdog Timer: Software program time-out intervals from 1~256 sec.



CMOS: Battery backup



Power Connector: One 4-pin and one 20-pin ATX power connector



Operating Temperature: -10~+60°C



Hardware Monitor: Winbond W83627



Board Size: 20.3 x 14.6 cm

3

1.3 Board Dimensions

4

Chapter 2

Unpacking

2.1 Opening the Delivery Package

The HS-4701 is packed in an anti-static bag. The board has
components that are easily damaged by static electricity. Do not
remove the anti-static wrapping until proper precautions have been
taken. Safety Instructions in front of this manual describe anti-static
precautions and procedures.

2.2 Inspection

After unpacking the board, place it on a raised surface and carefully
inspect the board for any damage that might have occurred during
shipment. Ground the board and exercise extreme care to prevent
damage to the board from static electricity.

Integrated circuits will sometimes come out of their sockets during
shipment. Examine all integrated circuits, particularly the BIOS,
processor, memory modules, and keyboard controller chip to ensure
that they are firmly seated. The HS-4701 delivery package contains the
following items:



HS-4701 Board x 1

 Utility CD Disk x 1


ATA/100 IDE flat cable x 2

 FDD flat cable x 1


Parallel flat cable x 1

 VGA cable +DB15 x 1


10-pin LAN cable + RJ-45 connector x 1

 8-pin USB split type cable with bracket x 1


MIC/Audio 8-pin cable + 2 phone jacks x 1

 4-in-1 COM Port cable + DB9 connectors x 1


PS/2 K/B & Mouse split-type cable x 1

 Jumper Bag x 1


User’s Manual

5

It is recommended that you keep all the parts of the delivery package
intact and store them in a safe/dry place for any unforeseen event
requiring the return shipment of the product. In case you discover any
missing and/or damaged items from the list of items, please contact
your dealer immediately.

6

Chapter 3

Hardware Installation

This chapter provides the information on how to install the hardware
using the HS-4701.

3.1 Before Installation

After confirming your package contents, you are now ready to install
your hardware. The following are important reminders and steps to
take before you begin with your installation process.

1. Make sure that all jumper settings match their default settings
and CMOS setup correctly. Refer to the sections on this chapter
for the default settings of each jumper.

2. Go through the connections of all external devices and make
sure that they are installed properly and configured correctly
within the CMOS setup. Refer to the sections on this chapter
for the detailed information on the connectors.

3. Keep the manual and diskette in good condition for future
reference and use.

4. Ma ke sure your power supply is usi ng for P4 only. One of 4-pin
connector is for +12V lead which should connect to PW2 and
20-pin ATX connector to PW1.

7

3.2 Board Layout

8

3.3 Jumper List

Jumper

JP1 Bus Clock Rate Select: Auto Detect Short 1-2 10
JP2 Clear CMOS: Normal Operation Short 1-2 18

J3

J6

Default Setting Setting Page

Only for Debug ---- ---­Use RS-232 or RS-422/485 Select:
RS-232

Short 1-3, 2-4,

7-9, 8-10

3.4 Connector List

Connector Definition Page

CN1 MIC In/Audio Out Connector 20
CD2 Line In Connector 20
CN2 External Speaker Connector 20
CN3 HDD LED Connector 19
CN4 2-pin ATX Power On/Off Switch 18
CN5 Reset Connector 19
CN6 Green LED Connector 19
CN7 Digital I/O Connector 21
CN8

CN9 RS-422/485 Connector 15
CN10 Internal CRT Connector 10
CN11 COM 1 Connector 15
CN12 COM 2 Connector 15
CN13
CN14 COM 4 Connector 15

DM1/DM2 188-pin DDR Sockets 10

FDC1 FDD Connector 14

FN1/FN2/FN3 Fan Connectors 18

IDE1/IDE2 IDE Connectors 11

J1 Inverter Power Connector 10
J2 TV-Out Connector 21
J4 LVDS Connector 10
J5 LVDS Connector 10

J7 Mini AGP Connector 21
PW1 20-pin ATX Connector 18
PW2 4-pin ATX Connector 18
PCI1 PCI Expansion Slot 21

KB1 8-pin KB/MS Connector 19

LPT1 Parallel Connector 16

USB1/USB2 USB Connectors 17

Internal LAN Connector 17

COM 3 Connector 15

15

9

3.5 Configuring the CPU

The HS-4701 offers the convenience in CPU installation with its
auto-detect feature. After installing a new microprocessor onboard, the
HS-4701 automatically identifies the frequency and clock speed of the
installed microprocessor chip, thereby eliminating the need for user to
do additional CPU configuration or hardware settings related to it.



JP1: Bus Clock Rate Select

Options Settings

Auto Detect (default) Short 1-2

100MHz Short 2-3
133MHz

Empty

13

3.6 System Memory

The HS-4701 provides two DDR sockets at locations DM1 and DM2.
The maximum capacity of the onboard memory is 2GB.

3.7 VGA Controller

NOTE 1:

NOTE 2:

NOTE 3:

HS-4701 does not support DSTN/STN Panel.

HS-4701 does not support 640*480 TFT Panel.

There are specific panel cable and inverter for each different LCD.

If clients need for others LCD (different from TOSHIBA
LTM10C348F), please contact with your sales.

The onboard Intel 82845GE with 1MB or 8MB memory supporting CRT
display up to 1280 x 1024 at 32-bit colors. The HS-4701 provides two
connection methods of CRT and LVDS Panel device. CN10 offers an
internal CRT connector, and J4, J5 offer two LVDS Panel connectors.



CN10: Internal CRT Connector

PIN Description PIN Description

1 Red 2 GND
3 Green 4 GND
5 Blue 6 GND
7

GND

8

DDCDTA

9 GND 10 HSYNC
11 GND 12 VSYNC
13 GND 14 DDCK
15 GND 16 N/C

115Red

Green

Blue

GND

GND

GND

GND

GND

2

16

GND

GND

GND

DDCDTA

HSYNC

VSYNC

DDCK

N/C

10



J1: Inverter Connector

PIN. Description

1 VCC12
2 VCC12
3 VCC5
4 ENABKL

1

5 ENAVDD
5 GND



J4: LVDS Connector

PIN Description PIN Description

1 VCC3 2 VCC3
3

GND

4

GND

5 A4M 6 A4P
7 A5M 8 A5P
9 A6M 10 A6P

11 CLK2M 12 CLK2P
13 A7M 14 A7P



J5: LVDS Connector

PIN Description PIN Descriptio

1 VCC3 2 VCC3
3 GND 4 GND
5 A0M 6 A0P
7 A1M 8 A1P
9 A2M 10 A2P

11 CLK1M 12 CLK1P
13 A3M 14 A3P

n

VCC12

VCC12

VCC5

GND

ENABKL

ENAVDD

6

A5P

A5M

A1P

A1M

A6P

A6M

A2P

A2M

A7P

CLK2P

14

13

A7M

CLK2M

A3P

CLK1P

14

13

A3M

CLK1M

A4P

VCC3

GND

2

1

A4M

GND

VCC3

VCC3

GND

A0P

2

1

A0M

GND

VCC3

3.8 PCI E-IDE Drive Connector

IDE1 and IDE2 are standard 40-pin connector daisy-chain driver
connector serves the PCI E-IDE drive provisions onboard the HS-4701.
A maximum of four ATA/33/66/100 IDE drives can connect to the
HS-4701 via IDE1 and IDE2.

11

 IDE1: Primary IDE Connector

PIN Description PIN Description

1 IDERST# 2 GND
3 PDD7 4 PDD8
5 PDD6 6 PDD9
7 PDD5 8 PDD10
9

11 PDD3 12 PDD12
13 PDD2 14 PDD13
15 PDD1 16 PDD14
17 PDD0 18 PDD15
19
21 PDREQ 22 GND
23 PDIOW# 24 GND
25 PDIOR# 26 GND
27 PIORDY 28 470Ω Pull GND
29 PDDACK# 30 GND
31 IRQ14 32 N/C
33 PDA1 34 P66DET
35 PDA0 36 PDA2
37 PDCS#1 38 PDCS#3
39 IDEACTP# 40 GND

PDD4

GND

10

20

PDD11

N/C

12

GND

PDD8

PDD9

PDD10

PDD11

PDD12

2

1

PDD7

PDD6

PDD5

PDD4

IDERST#

PDD3

PDD13

PDD14

PDD2

PDD1

PDD15

N/C

GND

PDD0

GND’GND

PDREQ

PDIOW#

GND

470Ω Pull GND

PDIOR#

PIORDY

GND

N/C

IRQ14

PDDACK#

P66DET

PDA2

PDA1

PDA0

PDCS#3

GND

PDCS#1

IDEACTP#

40

39

 IDE2: Secondary IDE Connector

PIN Description PIN Description

1 IDERST# 2 GND
3 SDD7 4 SDD8
5 SDD6 6 SDD9
7 SDD5 8 SDD10
9

11 SDD3 12 SDD12
13 SDD2 14 SDD13
15 SDD1 16 SDD14
17 SDD0 18 SDD15
19
21 SDREQ 22 GND
23 SDIOW# 24 GND
25 SDIOR# 26 GND
27 SIORDY 28 470Ω Pull GND
29 SDDACK# 30 GND
31 IRQ15 32 N/C
33 SDA1 34 S66DET
35 SDA0 36 SDA2
37 SDCS#1 38 SDCS#3
39 IDEACTP# 40 GND

SDD4

GND

10

20

SDD11

N/C

GND

SDD8

SDD9

SDD10

SDD11

SDD12

2

1

SDD7

SDD6

SDD5

SDD4

IDERST#

SDD3

SDD13

SDD14

SDD2

SDD1

SDD15

N/C

GND

SDD0

GND’GND

SDREQ

SDIOW#

GND

SDIOR#

470Ω Pull GND

SIORDY

GND

SDDACK#

N/C

S66DET

SDA2

SDCS#3

GND

40

39

SDA1

SDA0

IRQ15

SDCS#1

IDEACTP#

13

3.9 Floppy Disk Drive Connector

The HS-4701 uses a standard 34-pin header connector, FDC1, for
floppy disk drive connection. A total of two FDD drives may be
connected to FDC at any given time.



FDC1: FDD Connector

PIN Description PIN Description

1 GND 2 RWC#
3 GND 4 N/C
5 GND 6 DS1#
7 GND 8 Index#

9 GND 10 MOA#
11 GND 12 DSB#
13 GND 14 DSA#
15 GND 16 MOB#
17 GND 18 DIR#
19 GND 20 STEP#
21 GND 22 WD#
23 GND 24 WE#
25 GND 26 TRACK0#
27 GND 28 WP#
29

N/C

30

31 GND 32 HEAD#
33 N/C 34 DSKCHG#

RDATA#

14

RWC#

N/C

DS1#

INDEX#

MOA#

DSB#

DSA#

MOB#

DIR#

STEP#

WD#’WE#

TRACK0#

WP#

RDATA#

HEAD#

DSKCHG#

2

1

GND

GND

GND

GND

GND

GND

GND

GND

GND

GND

GND

GND

GND

GND

N/C

GND

N/C

34

33

3.10 Serial Port Connectors

The HS-4701 offers two NS16C550 compatible UARTs with
Read/Receive 16-byte FIFO serial ports and four internal 10-pin
headers. There is one RS-422/485 connector.



CN11~CN14: COM1~COM4 Connectors (5x2 Header)

PIN Description PIN Description

1 DCD0 2 DSR0
3 RXDD0 4 RTS0
5 TXDD0 6 CTS0
7 DTR0 8 RI0
9

GND

10

N/C

11 DCD1 12 DSR1
13 RXDD1 14 RTS1
15 TXDD1 16 CTS1
17 DTR1 18 RI1
19 GND 20 N/C
21 DCD2 22 DSR2
23 RXDD2 24 RTS2
25 TXDD2 26 CTS2
27 DTR2 28 RI2
29 GND 30 N/C
31

DCD3

32

DSR3

33 RXDD3 34 RTS3
35 TXDD3 36 CTS3
37 DTR3 38 RI3
39 GND 40 N/C



CN9: RS-422/485 Connector

PIN Description PIN Descriptio

1 TX- 2 TX+
3 RX+ 4 RX-
5 GND 6 RTS-
7 RTS+ 8 CTS+
9 CTS- 10 N/C

RXDD1

RXDD2

RXDD3

n

DCD0

RXDD0

TXDD0

DTR0

GND

DCD1

TXDD1

DTR1

GND

DCD2

TXDD2

DTR2

GND

DCD3

TXDD3

DTR3

GND

1

2

DSR0

RTS0

CTS0

RI0

N/C

DSR1

RTS1

CTS1

RI1

N/C

DSR2

RTS2

CTS2

RI2

N/C

DSR3

RTS3

CTS3

RI3

N/C

39

40

1

TX-

3

RX+

5

GND

7

RTS+

9

CTS-

COM1

COM2

COM3

COM4

2

TX+

4

RX-

6

RTS-

8

CTS+

10

N/C

15



J6: Use RS-232 or RS-422/485 Select

Options Settings

1

RS-232 (default) Short 1-3, 2-4, 7-9, 8-10

RS-422/485 Short 3-5, 4-6, 9-11, 10-12

11212

3.11 Parallel Connector

LPT1 is a standard 26-pin flat cable connector deigned to
accommodate parallel port connection onboard the HS-4701.



LPT1: Parallel Connector

PIN Description PIN Description

1 STB# 14 AFD#
2 PDR0 15 ERR#
3 PDR1 16 INIT#
4 PDR2 17 SLIN#
5 PDR3 18 GND
6

PDR4

19

7 PDR5 20 GND
8 PDR6 21 GND
9 PDR7 22 GND

10 Acknowledge 23 GND
11

Busy

24

12 Paper Empty 25 GND
13 Printer Select 26 N/C

GND

GND

16

14

AFD#

ERR#

INIT#

SLIN#

GND

GND

GND

GND

GND

GND

GND

GND

N/C

26

1

STB#

PDR0

PDR1

PDR2

PDR3

PDR4

PDR5

PDR6

PDR7

Busy

Acknowledge

13

Paper empty

Printer Select

3.12 Ethernet Connector

The HS-4701 has Intel® 82562 10/100 Based LAN controller and
provides one 10-pin internal connector. Please refer to the following for
its pin information.



CN8: LAN Connector (Intel 82562)

PIN Description PIN Description

1 3.3VSTBY 2 LILED#
3

RRX+

4

RRX-

5 ACTLED# 6 LANC1
7 SPLED# 8 LANC2
9 TTX+ 10 TTX-

LILED#

RRX-

LANC1

TTX-

246810

13579

3.3VSTBY

LANC2

RRX+

TTX+

SPLED#

ACTLED#

3.13 USB Connector

The HS-4701 provides four USB ports, at locations USB1 and USB2,
for four USB connections to the HS-4701.



USB1: USB Connector

VCC

GND

VCC

GND

12

VCC

USBP1N

USBP1P

GND

78

12

VCC

USBP3N

USBP3P

GND

78

PIN Description PIN Description

1 VCC 2 VCC
3 USBP0N 4 USBP1N
5 USBP0P 6 USBP1P
7

GND

8

GND



USB2: USB Connector

PIN Description PIN Description

1 VCC 2 VCC
3 USBP2N 4 USBP3N
5 USBP2P 6 USBP3P
7 GND 8 GND

USBP0N

USBP0P

USBP2N

USBP2P

17

3.14 CMOS Data Clear

The HS-4701 has a Clear CMOS jumper on JP2.



JP2: Clear CMOS

Options Settings

Normal Operation

IMPORTANT:

(default)

Clear CMOS Short 2-3

Before you turn on the power of your system, please

Short 1-2

set JP2 to short 1-2 for normal operation.

13

GND

Battery

RTCRST#

3.15 Power and Fan Connectors

HS-4701 provides one 20-pin and one 4-pin ATX power connectors at
PW1 and PW2.

HS-4701 must using P4 power supply. One of 4-pin connector is for
+12V lead which should connect to PW2.

20-pin ATX Power Connector can connect to Backplane or to PW1.



PW2: 4-pin ATX Power In Connector

PIN Description PIN Description

1 GND 2 GND
3 +12V 4 +12V



PW1: 20-pin ATX Power In Connector

PIN Description PIN Description

1 +3.3V 11 +3.3V
2 +3.3V 12 -12V
3 GND 13 GND
4 +5V 14 PS_ON
5 GND 15 GND
6
7 GND 17 GND
8 PWROK 18 -5V
9 5VSB 19 +5V

10 +12V 20 +5V

+5V

16

GND

1

3

10 20

111

2

4

18



CN4: 2-pin ATX Power On/Off Switch

PIN Description

1 5VSTBY
2 Power On/Off

12

Connector FN1, FN2 and FN3 onboard HS-4701 are 3-pin fan
connectors.



FN1, FN2 and FN3: Fan Connectors

PIN Description

1 GND
2
3 Fan Speed

+12V

1

GND

+12V

Fan Speed

3

3.16 Keyboard/Mouse Connectors

The HS-4701 offers one possibility for keyboard/mouse connection is
via KB1.



KB1: 8-pin Keyboard/Mouse Connector

PIN Description

1 GND
2 VCC
3 MS_DATA
4 MS_CLK
5
6 VCC
7 KB_DATA
8 KB_CLK

GND

1

GND

MS_DATA

VCC

GND

MS_CLK

VCC

KB_CLK

KB_DATA

8

3.17 System Front Panel Connectors

The HS-4701 has one LED at location CN3 that indicates the HDD
status.



CN3: HDD LED Connector

PIN Description

1 150Ω Pull +5V
2 HDD ACTIVE#

CN5 is the Reset Button connector onboard. The CN6 is Green
function LED indicates.

19



CN5: Reset Button Connector

PIN Description

1 GND
2 External Reset



CN6: Green LED Connector

12

GND

Ext. Reset

PIN Description

1
2 ACTIVE#

150Ω Pull +5V

3.18 External Speaker

Aside from the buzzer at location BZ1 onboard, the HS-4701 also
offers a connector (CN2) for an external speaker connection. The table
below lists the pin assignments of CN2.



CN2: External Speaker Connector

PIN Description

1 VCC
2 GND
3 GND

Speaker Signal

4

14

VCC

GND

GND

Speaker Signal

3.19 Audio Connectors

The HS-4701 has an onboard AC97 3D audio interface. The following
table list the pin assignments of the MIC In / Audio Out and Line In
connector.



CN1: MIC In / Audio Out Connector

PIN Description PIN Description

1 AOUT_L 2 AOUT_R
3 GND 4 GND
5 MIC_IN 6 N/C
7 GND 8 GND

20

2

1

8

7



CD2: Line In Connector

PIN Description PIN Description

1 IN_R 2 GND
3 GND 4 IN_L

14

GND

IN_L

IN_R

GND

3.20 Digital Input/Output

The HS-4701 provides a CN7 connector for Digital I/O function.

 CN7: Digital I/O Connector

PIN Description PIN Description

1 VCC5 2 VCC5
3

DO_0

4

5 DO_1 6 DI_1
7

DO_2

8

9 DO_3 10 DI_3
11 DO_4 12 DI_4
13 DO_5 14 DI_5
15 DO_6 16 DI_6
17 DO_7 18 DI_7
19 DO_8 20 DI_8
21 DO_9 22 DI_9
23 DO_10 24 DI_10
25 DO_11 26 DI_11
27 DO_12 28 DI_12
29

DO_13

30

31 DO_14 32 DI_14
33 DO_15 34 DI_15
35 GND 36 GND

DI_0

DI_2

DI_13

VCC5

DO_0

DO_1

DO_2

DO_3

DO_4

DO_5

DO_6

DO_7

DO_8

DO_9

DO_10

DO_11

DO_12

1

2

DI_0

DI_1

DI_2

DI_3

DI_4

DI_5

DI_6

DI_7

DI_8

VCC5

DI_9

DI_10

DI_11

DI_12

GND

DO_13

DO_14

DO_15

35

36

GND

DI_13

DI_14

DI_15

21

3.21 TV Out Function

HS-4701 can support TV-Out function which input could be up to 800 x
600 graphics resolutions. World Wide Video standards are supported
including NTSC-M (North America, Taiwan), NTSC-J (Japan), PAL-B,
D, G, H, I (Europe, Asia), PAL-M (Brazil), PAL-N (Uruguay, Paraguay)
and PAL-NC (Argentina).



J2: TV-Out Connector

PIN Description PIN Description

1 GND 2 TVCVB

3.22 Mini AGP Connector

HS-4701 provides one Mini AGP expansion slot, has at location J7, you
can use slot for expansion when necessary.

3.23 PCI Expansion Slot

HS-4701 provides one standard PCI expansion slot at PCI1.

22

Chapter 4

Award BIOS Setup

The HS-4701 uses Award BIOS for the system configuration. The
Award BIOS setup program is designed to provide the maximum
flexibility in configuring the system by offering various options that
could be selected for end-user requirements. This chapter is written to
assist you in the proper usage of these features.

4.1 Starting Setup

The Award BIOS is immediately activated when you first power on the
computer. The BIOS reads the system information contained in the
CMOS and begins the process of checking out the system and
configuring it. When it finishes, the BIOS will seek an operating system
on one of the disks and then launch and turn control over to the
operating system.

While the BIOS is in control, the Setup program can be activated in one
of two ways:

1. By pressing <Del> immediately after switching the system on, or

2. By pressing the <Del> key when the following message appears
briefly at the bottom of the screen during the POST (Power On Self
Test).

Press DEL to enter SETUP.

If the message disappears before you respond and you still wish to
enter Setup, restart the system to try again by turning it OFF then ON or
pressing the "RESET" button on the system case. You may also restart
by simultaneously pressing <Ctrl>, <Alt>, and <Delete> keys. If you do
not press the keys at the correct time and the system does not boot, an
error message will be displayed and you will again be asked to...

PRESS F1 TO CONTINUE, DEL TO ENTER SETUP

23

4.2 Using Setup

In general, you use the arrow keys to highlight items, press <Enter> to
select, use the <PageUp> and <PageDown> keys to change entries,
press <F1> for help and press <Esc> to quit. The following table
provides more detail about how to navigate in the Setup program using
the keyboard.

Up arrow

Down arrow Move to next item

Left arrow Move to the item in the left hand

Right arrow Move to the item in the right hand

Esc key Main Menu -- Quit and not save changes into CMOS

PgUp key Increase the numeric value or make changes
PgDn key Decrease the numeric value or make changes

+ key

- key Decrease the numeric value or make changes

F1 key General help, only for Status Page Setup Menu and Option

(Shift)F2 key Change color from total 16 colors. F2 to select color

F3 key Calendar, only for Status Page Setup Menu
F4 key Reserved
F5 key Restore the previous CMOS value from CMOS, only for

F6 key

F7 key Load the default
F8 key Reserved
F9 key Reserved

F10 key Save all the CMOS changes, only for Main Menu

Move to previous item

Status Page Setup Menu and Option Page Setup Menu -­Exit current page and return to Main Menu

Increase the numeric value or make changes

Page Setup Menu

forward, (Shift) F2 to select color backward

Option Page Setup Menu
Load the default CMOS value from BIOS default table, only
for Option Page Setup Menu

4.2.1 Getting Help

Press F1 to pop up a small help window that describes the appropriate
keys to use and the possible selections for the highlighted item. To exit
the Help Window press <Esc> or the F1 key again.

24

4.3 Main Menu

Once you enter the Award BIOS CMOS Setup Utility, the Main Menu
will appear on the screen. The Main Menu allows you to select from
several setup functions and two exit choices. Use the arrow keys to
select among the items and press <Enter> to enter the sub-menu.

Phoenix – AwardBIOS CMOS Setup Utility

`

Standard CMOS Features

`

Advanced BIOS Features

`

Advanced Chipset Features

`

Integrated Peripherals

`

Power Management Setup

`

PnP/PCI Configurations

`

PC Health Status

Esc：Quit F9：Menu in BIOS
F10：Save & Exit Setup

NOTE:

A brief description of the highlighted choice appears at the bottom

Time, Date, Hard Disk Type…

of the screen.

`

Frequency/Voltage Control

Load Fail-Safe Defaults

Load Optimized Defaults

Set Supervisor Password

Set User Password

Save & Exit Setup

Exit Without Saving



：

Select Item

25

4.4 Standard CMOS Setup

The Standard Setup is used for the basic hardware system
configuration. The main function is for Data/Time and Floppy/Hard Disk
Drive settings. Please refer to the following screen for the setup. When
the IDE hard disk drive you are using is larger than 528MB, you must
set the HDD mode to
BIOS SETUP to install the HDD correctly.

mode. Please use the IDE Setup Utility in

LBA

Phoenix – AwardBIOS CMOS Setup Utility

Standard CMOS Features

Date (mm:dd:yy) Wed, Oct 31 2001 Item Help
Time (hh:mm:ss) 10 : 32 :57 Menu Level X

X

IDE Primary Master

X

IDE Primary Slave Change the day, month,

X

IDE Secondary Master year and century

X

IDE Secondary Slave

Drive A [1.44M, 3.5in.]
Drive B [None]

Video [EGA/VGA]
Halt On [All, But Keyboard]

Base Memory 640K
Extended Memory 65472K
Total Memory 1024K



: Select Item + / - /PU/PD: Value F10: Save ESC: Quit F1: General Help

F5: Previous Values F6: Fail-Safe Defaults F7: Optimized Defaults

26

4.5 Advanced CMOS Setup

This section allows you to configure your system for the basic
operation. You have the opportunity to select the system’s default
speed, boot-up sequence, keyboard operation, shadowing and
security.

Phoenix – AwardBIOS CMOS Setup Utility

Item Help

Virus Warning [Disabled] Menu Level X
CPU L1& L2 Cache [Enabled]
Hyper-Threading [Enabled]
Quick Power On Self Test [Enabled]
First Boot Device [Floppy] Allows you to choose
Second Boot Device [HDD-0] the VIRUS warning
Third Boot Device [LS120] feature for IDE Hard
Boot Other Device [Enabled] Disk boot sector
Swap Floppy Drive [Disabled] protection. If this
Boot Up Floppy Seek [Enabled] function is enabled
Boot Up Num Lock Status [On] and someone attempt to
Gate A20 Option [Fast] write data into this
Typematic Rate Setting [Disabled] area, BIOS will show
Typematic Rate (Chars/Sec) 6 a warning message on
Typematic Delay (Msec) 250 screen and alarm beep
Security Option [Setup]
APIC Mode [Enabled]
MPS Version Control For OS [1.4]
OS Select For DRAM > 64MB [Non-OS2]
Report No FDD for WIN95 [NO]
Small Logo (EPA) Show [Enabled]

: Select Item + / - /PU/PD: Value F10: Save ESC: Quit F1: General Help
F5: Previous Values F6: Fail-Safe Defaults F7: Optimized Defaults

Advanced BIOS Features

27

4.6 Advanced Chipset Setup

This section allows you to configure the system based on the specific
features of the installed chipset. This chipset manages bus speeds and
the access to the system memory resources, such as DRAM and the
external cache. It also coordinates the communications between the
conventional ISA and PCI buses. It must be stated that these items
should never be altered. The default settings have been chosen
because they provide the best operating conditions for your system.
You might consider and make any changes only if you discover that the
data has been lost while using your system.

Phoenix – AwardBIOS CMOS Setup Utility

Advanced Chipset Features

Item Help
DRAM Timing Selectable [By SPD] Menu Level X
CAS Latency Time [1.5]
Active to Precharge Delay [7]
DRAM RAS# to CAS# Delay [3]
DRAM RAS# Precharge [3]
Turbo Mode [Disabled]
Memory Frequency For [Auto]
System BIOS Cacheable [Enabled]
Video BIOS Cacheable [Enabled]
Memory Hole At 15M-16M [Disabled]
Delayed Transaction [Enabled]
Delay Prior to Thermal [16Min]
AGP Aperture Size (MB) [64]

On-chip VGA [Enabled]
On-chip Frame Buffer size [8MB]
Boot Display [CRT]
Panel Scaling [Auto]
Panel Number [1]

** ON-chip VGA Setting **



: Select Item + / - /PU/PD: Value F10: Save ESC: Quit F1: General Help

F5: Previous Values F6: Fail-Safe Defaults F7: Optimized Defaults

NOTE:

28

Panel Number: 1 (Default Panel 1: TOSHIBA LTM10C348F)

4.7 Power Management Setup

The Power Management Setup allows user to configure the system for
saving energy in a most effective way while operating in a manner
consistent with his own style of computer use.

Phoenix – AwardBIOS CMOS Setup Utility

ACPI function [Enabled] Item Help

ACPI Suspend Type [S1(POS)] Menu Level X

Run VGABIOS id S3 Resume Auto

Power Management [Use Define]

Video off Method [DPMS]

Video off In Suspend [Yes]

Suspend Type [Stop Grant]

MODEM Use IRQ [Modify]

Suspend Mode [Disabled]

HDD Power Down [Disabled]

Soft-off by PWR-BTTN [Instant-Off]

CPU THRM-throttling [50.00%]

Wake-up by PCI card [Enabled]

Power On by Ring [Enabled]

USB KB Wake-up From S3 Disabled

Resume by Alarm [Disabled]

Date(of Month) Alarm 0

Time(hh:mm:ss) Alarm 0:0:0

** Reload Global Timer Events **

Primary IDE 0 [Disabled]

Primary IDE 1 [Disabled]

Secondary IDE 0 [Disabled]

Secondary IDE 1 [Disabled]

FDD, COM, LPT Port [Disabled]

PCI PIRQ[A-D]# [Disabled]



: Select Item + / - /PU/PD: Value F10: Save ESC: Quit F1: General Help

F5: Previous Values F6: Fail-Safe Defaults F7: Optimized Defaults

Power Management Setup

29

4.8 PCI / Plug and Play Setup

This section describes configuring the PCI bus system. PCI, or
Personal Computer Interconnect, is a system that allows I/O devices to
operate at speeds nearing the speed the CPU itself uses when
communicating with its own special components. This section covers
some very technical items and it is strongly recommended that only
experienced users should make any changes to the default settings.

Phoenix – AwardBIOS CMOS Setup Utility

PNP OS Installed [No] Item Help

Reset Configuration Data [Disabled] Menu Level X

Resources Controlled By [Auto(ESCD)] Select Yes if you are

IRQ Resources Press Enter using a plug and play

DMA Resources Press Enter capable operating

system. Select No

PCI/VGA Palette Snoop [Disabled] if you need the BIOS

to configure

non-boot devices

: Select Item + / - /PU/PD: Value F10: Save ESC: Quit F1: General Help
F5: Previous Values F6: Fail-Safe Defaults F7: Optimized Defaults

PnP/PCI Configurations

30

4.9 Peripheral Setup

The IDE hard drive controllers can support up to four separate hard
drives. These drives have a master/slave relationship that is
determined by the cabling configuration used to attach them to the
controller. Your system supports two IDE controllers--a primary and a
secondary--so you can install up to four separate hard disks.

Phoenix – AwardBIOS CMOS Setup Utility

On-chip Primary PCI IDE [Enabled] Item Help
IDE Primary Master PIO [Auto] Menu Level X
IDE Primary Slave PIO [Auto]
IDE Primary Master UDMA [Auto]
IDE Primary Slave UDMA [Auto]
On-chip Secondary PCI IDE [Enabled]
IDE Secondary Master PIO [Auto]
IDE Secondary Slave PIO [Auto]
IDE Secondary Master UDMA [Auto]
IDE Secondary Slave UDMA [Auto]
USB Controller [Enabled]
USB 2.0 Controller [Enabled]
USB Keyboard Support [Disabled]
USB Mouse Support [Disabled]
AC97 Audio [Auto]
Init Display First [PCI Slot]
IDE HDD Block Mode [Enabled]
POWER ON Function [BUTTON ONLY]
KB Power ON Password [Enter]
Hot Key Power On [Ctrl-F1]
Onboard FDC Controller [Enabled]
Onboard Serial Port 1 [3F8/IRQ4]
Onboard Serial Port 2 [2F8/IRQ3]
UART Mode Select [Normal]
RxD, TxD Active [Hi, Lo]
IR Transmission delay [Enabled]
UR2 Duplex Mode [Half]
Use IR Pins [IR-RX2TX2]
Onboard Parallel Port [378/IRQ7]
Parallel Port Mode [SPP]
EPP Mode Select [EPP1.7]
ECP Mode Use DMA [3]
PWRON After PWR-Fail [Off]
Midi Port Address [330]
Midi Port IRQ [5]
Onboard Serial Port 3 [3E8]
Serial Port 3 Use IRQ IRQ10]
Onboard Serial Port 4 [2E8]
Serial Port 4 Use IRQ [IRQ11]



: Select Item + / - /PU/PD: Value F10: Save ESC: Quit F1: General Help

F5: Previous Values F6: Fail-Safe Defaults F7: Optimized Defaults

Integrated Peripherals

31

4.10 PC Health Status

Phoenix – AwardBIOS CMOS Setup Utility

CPU Warning Temperature [Disabled] Item Help

Current System Temp. Menu Level X

Current CPU1 Temperature

Current CPUFAN1 Speed

Current CPUFAN2 Speed

Current CPUFAN3 Speed

IN0(V)

IN1(V)

IN2(V)

+5V

+12V

-12V

-5V

VBAT(V)

5VSB(V)

Shutdown Temperature [Disabled]

: Select Item + / - /PU/PD: Value F10: Save ESC: Quit F1: General Help
F5: Previous Values F6: Fail-Safe Defaults F7: Optimized Defaults

PC Health Status

4.11 Frequency/Voltage Control

Phoenix – AwardBIOS CMOS Setup Utility

CPU Clock Ratio [Auto (Modify)] Item Help

Auto Detect PCI Clk [Enabled] Menu Level X

Spread Specturm [Disabled]



: Select Item + / - /PU/PD: Value F10: Save ESC: Quit F1: General Help

F5: Previous Values F6: Fail-Safe Defaults F7: Optimized Defaults

Frequency/Voltage Control

32

Chapter 5

Software Utilities

This chapter contains the detailed information of IDE, VGA, LAN and
Audio driver installation procedures. The utility disk that came with the
delivery package contains an auto-run program that invokes the
installation programs for the VGA, LAN and Audio drivers. The
following sections describe the installation procedures of each driver
based on Win 95/98, Win 2000 and Win NT operating systems. It is
recommended that you install the drivers matching the sections listed
in this chapter.

5.1 IDE Driver Installation

5.1.1 Installing Intel Chipset Software Utility

1. Insert Utility CD Disk to your CD ROM drive. The main menu will

pop up as shown below. Select on the HS-4701 button to
launch the installation program.

2. Click on the ICH4 Driver button to continue.

33

3. Immediately after clicking the IDE b u t t o n i n S t e p 1 , t h e p r ogram

launches the InstallShield Wizard that will assist you in the
installation process. Click on the N

4. The Intel OEM Software License Agreement dialog box then

appears on the screen. Choose Y

ext > button to proceed.

es to proceed.

34

5. When the Readme Information dialog box pops up, just click on

the N

ext button to proceed.

6. Once the Install Shield Wizard finishes updating your system, it

will prompt you to restart the computer. Tick on the Yes, I

want to restart my computer now followed by a click on the
F

inish but ton to re boo t. On ly af ter your com pute r bo ots will t he

new settings take effect.

35

5.1.2 Installing Intel Application Accelerator

1. Insert Utility CD Disk to your CD ROM drive. The main menu will
pop up as shown below. Select on the HS-4701 button to launch
the installation program.

2. Click on the IDE Driver button to continue.

3. When the dialog box below appears, make sure you close all
other Windows applications then click on the N
proceed.

ext > button to

36

4. The Intel OEM Software License Agreement dialog box then
appears on the screen. Choose Y

5. Setup will then prompt you to specify the path where you would
like the Security driver installed. Select the N
you have made your path/installation choice.

es to proceed.

ext > button after

6. Once the setup program finishes copying files into your system, it
will prompt you to restart the computer. Tick on the Yes, I want

to restart my computer now followed by a click on the F

inish

37

button to reboot. Only after your computer boots will the new
settings take effect.

5.2 VGA Driver Installation

5.2.1 Win 98

1. Insert Utility CD Disk to your CD ROM drive. The main menu will
pop up as shown below. Select on the HS-4701 button to launch
the installation program.

2. Click on the VGA Driver button to continue.

38

3. Click on the Windows 9x button to continue.

4. When the dialog box below appears, make sure you close all

other Windows applications then click on the N
proceed.

ext > button to

5. The Intel OEM Software License Agreement dialog box then

appears on the screen. Choose Y

es to proceed.

39

6. Once the setup program finishes copying files into your system, it

will prompt you to restart the computer. Tick on the Yes, I want
to restart my computer now followed by a click on the F
button to reboot. Only after your computer boots will the new
settings take effect.

inish

NOTE:

40

Installation procedure for Windows 98 is similar to Windows95.

5.2.2 Win NT

NOTE:

1. Insert Utility CD Disk to your CD ROM drive. The main menu will

2. Click on the VGA Driver button to continue.

3. Click on the Windows NT button to continue.

Please make sure you have already install Service Pack 6.0.

pop up as shown below. Select on the HS-4701 button to launch
the installation program.

41

4. When the dialog box below appears, make sure you close all

other Windows applications then click on the N
proceed.

5. The Intel OEM Software License Agreement dialog box then

appears on the screen. Choose Y

es to proceed.

ext > button to

42

6. Once the setup program finishes copying files into your system, it

will prompt you to restart the computer. Tick on the Yes, I want
to restart my computer now followed by a click on the F
button to reboot. Only after your computer boots will the new
settings take effect.

inish

5.2.3 Win 2000

1. Insert Utility CD Disk to your CD ROM drive. The main menu will
pop up as shown below. Select on the HS-4701 button to launch
the installation program.

2. Click on the VGA Driver button to continue.

43

3. Click on the Windows 2K button to continue.

4. When the dialog box below appears, make sure you close all
other Windows applications then click on the N
proceed.

ext > button to

44

5. The Intel OEM Software License Agreement dialog box then
appears on the screen. Choose Y

6. Once the setup program finishes copying files into your system, it
will prompt you to restart the computer. Tick on the Yes, I want
to restart my computer now followed by a click on the F
button to reboot. Only after your computer boots will the new
settings take effect.

es to proceed.

inish

45

5.3 LAN Driver Installation

5.3.1 Win 95/98

1. Insert Utility CD Disk to your CD ROM drive. The main menu will
pop up as shown below. Select on the HS-4701 button to launch
the installation program.

2. Click on the LAN Driver button to continue.

3. Click on the Windows 9x button to continue.

46

4. When the dialog box below appears, make sure you close all

other Windows applications then click on the N
proceed.

5. The Intel OEM Software License Agreement dialog box then

appears on the screen. Choose Accept to proceed.

ext > button to

47

6. The Setup Type dialog box then appears on the screen. Choose

Typical to proceed.

7. When the dialog box below appears, make sure you close all

other Windows applications then click on the I
proceed.

nstall button to

48

8. When the dialog box below appears, it means your driver is install

completed. Click F

9. Once the setup program finishes copying files into your system, it

will prompt you to restart the computer. Tick on the Yes to
reboot. Only after your computer boots will the new settings take
effect.

inish button to proceed.

5.3.2 Win NT

NOTE:

1. The system automatically detects the absence of Windows NT

Please make sure you have already install Service Pack 6.0.

Networking. Click on the Y

es button to start installation.

49

2. Tick on the Wired to Network once the following screen

appears. Click on the Next to proceed.

3. Click on the St

Network Adapter.

art Search button for the program to locate the

50

4. Once setup finishes the search, it will list a number of adapters

for you to choose from. Press on the H
the driver path location.

5. Setup now asks you for the location of the driver. When you have

entered the new driver path, press on the OK button to continue.

ave Disk button to assign

6. When Setup finds the information it needs about the new driver,

it will display the device it found on the following screen. Please
choose “Intel(R) PRO/100 Family Adapter”. Press on the OK
button to accept and proceed.

51

7. Setup then returns to Network Setup Wizard screen and displays

your new Network Adapter. Click on N

8. The Network Setup Wizard then allows you to set the Network

Protocols on your network. Select the appropriate protocol and
then click on Next to continue.

ext to continue.

52

9. Before Setup starts installing the components found and the

settings you made, it will give you the option to proceed or go
back for changes from the following screen. Click on the N
button once you are sure of your devices.

10. Windows NT Setup will then need to copy files necessary to

update the system information. Specify the path then press

Continue.

ext

11. When Setup asks if you wish to change the TCP/IP settings of

your system, select the appropriately. The default choice is N

12. Setup then starts the Networking installation and copies the files.

o.

53

13. When the screen below appears, click on Next to continue.

14. Setup then prompts you that it is ready to start the network. You

may complete the installation thereafter. Click on N
continue.

ext to

54

15. Assign the workgroup or domain setting of your computer. Click

on Next to continue.

16. Click on the Yes button to restart your computer. The LAN driver

installation for WIN NT4.0 is now complete.

5.4 Audio Driver Installation

1. Insert Utility CD Disk to your CD ROM drive. The main menu will
pop up as shown below. Select on the HS-4701 button to launch
the installation program.

55

2. Click on the AUDIO Driver button to continue.

3. When the dialog box below appears, make sure you close all

other Windows applications then click on the N
proceed.

ext > button to

56

4. Once the InstallShield Wizard completes the operation and

update of your AC97 driver, it will ask you to remove disks from
their drives, and prompt you to restart your system. Tick on the
Yes, I want to restart my computer now. Afterwards, click on the

inish button to complete the installation process. The system

F

changes you made will take effect after the system restarts.

57

This page intentionally left blank.

58