Boser HS-4655 User Manual

Download

Page 1

HS-4655

Eden Embedded Engine Board

‧CompactFlash‧Mini PCI‧133MHz FSB‧

SO-DIMM‧CRT/LVDS Panel‧

‧

‧TV-Out‧Dual LAN‧Audio‧ATA/33/66/100‧

RS-232/422/485‧8 COM‧USB2.0‧PC/104‧

‧

‧WDT‧H/W Monitor‧

Industrial Embedded Single Board computer‧

‧

Page 2

The accuracy of contents in this manual has passed thorough checking and review before publishing. BOSER Technology Co., Ltd., the manufacturer and publisher, is not liable for any infringements of patents or other rights resulting from its use. The

not be responsible for any direct, indirect, special, incidental or consequential damages arisi ng from t he use of this pro duct or doc ument atio n, even if advised of the possibility of such damage(s).

This manual is copyrighted and BOSER Technology Co., Ltd. reserves all documentation rights. Unauthorized reproduction, tran smission, translation, and storage of any form and means (i.e.,

of this document, in whole or partly, is prohibited, unless granted permission by BOSER Technology Co., Ltd.

BOSER Technology Co., Ltd.

this document without due notice. responsibility for any errors or omissions that may appear in this manual, nor does it make any commitment to update the information contained herein.

BOSER is a registered trademark of BOSER Technology Co., Ltd. ISB is a registered trademark of BOSER Technology Co., Ltd. Intel is a registered trademark of Intel Corporation. Award is a registered trademark of Award Software, Inc. AMI is a registered trademark of AMI Software, Inc. All other trademarks, products and or product names mentioned herein are

mentioned for identification purposes only, and may be trademarks and/or registered trademarks of their respective companies or owners.

reserves the right to change or improve the contents of

electronic, mechanical, photocopying, recording)

BOSER Technology Co., Ltd. assumes no

manufacturer will

Page 3

Table of Contents

Chapter 1 General Description..................................1

1.1 Major Features....................................................................... 2

1.2 Specifications........................................................................ 3

1.3 Board Dimensions.................................................................4

Chapter 2 Unpacking..................................................5

2.1 Opening the Delivery Package............................................. 5

2.2 Inspection...............................................................................5

Chapter 3 Hardware Installation ..............................7

3.1 Before Installation.................................................................7

3.2 Board Layout .................................................. ....................... 8

3.3 Jumper List....................... .... ... .... .... .... ... .... .... .... ....... .... .... ... .9

3.4 Connector List....................................................................... 9

3.5 Configuring the CPU........................................................... 11

3.6 System Memory............................................................. ...... 11

3.7 VGA Controller ....................................................................11

3.8 PCI E-IDE Drive Connector................................................. 13

3.9 Floppy Disk Drive Connector............................................. 14

3.10 Parallel Connector...............................................................15

3.11 Serial Port Connectors ....................................................... 15

3.12 Ethernet Connector.............................................................19

3.13 USB Connector.................................................................. ..19

3.14 CMOS Data Clear................................................................. 20

3.15 Power and Fan Connectors................................................ 20

3.16 Keyboard/Mouse Connectors ............................................ 21

3.17 System Front Panel Connectors........................................ 21

3.18 Watchdog Timer ................................................. ................. 22

3.19 Mini PCI Connector ............................................................. 24

3.21 PC/104 Connectors .............................................................26

3.21 Audio Connectors ............................................................... 28

3.23 CompactFlash™ Connector................................................ 28

3.23 TV-Out Connector ...............................................................29

3.24 PCI Expansion Slot ............................................................. 30

Page 4

Chapter 4 AMI BIOS Setup.....................................31

4.1 Starting Setup...................................................................... 31

4.2 Using Setup ........................................................................ . 32

4.3 Main Menu............................................................................ 33

4.4 Standard CMOS Setup........................................................ 34

4.5 Advanced CMOS Setup ...................................................... 35

4.6 Advanced Chipset Setup.................................................... 36

4.7 Power Management Setup ................................................. 37

4.8 PCI / Plug and Play Setup................................................... 38

4.9 Peripheral Setup.................................................................. 39

4.10 Hardware Monitor Setup..................................................... 40

4.11 Auto-Detect Hard Disks...................................................... 41

4.12 Change Supervisor/User Password.................................. 42

4.13 Auto Configuration with Optimal Settings ....................... 43

4.14 Auto Configuration with Fail Safe Settings...................... 44

4.15 Save Settings and Exit........................................................ 45

4.16 Exit Without Saving............................................................. 46

Chapter 5 Software Utilities.....................................47

5.1 IDE Driver Installation......................................................... 47

5.2 VGA Driver Installation....................................................... 52

5.2.1 VGA Driver Installation for WIN95/98/2K........................................52

5.2.2 VGA Driver Installation for WIN NT4.0................................................55

5.3 LAN Driver Installation........................................................ 58

5.3.1 LAN Driver Installation for WIN95/98/2K.........................................58

5.3.2 LAN Driver Installation for WIN NT4.0.................................................64

5.4 Audio Driver Installation..................................................... 74

5.5 USB2.0 Driver Installation.................................................. 77

5.5.1 Win 95/98 ........................................................................................................77

5.5.2 Win 2000 ........................................................................... ............................78

5.5.3 Win XP .......................................................................................................82

5.6 COM5~COM8 Driver Installation........................................ 84

5.6.1 Win 2000 ........................................................................... ............................84

5.6.2 Win XP .......................................................................................................86

Page 5

Safety Instructions

Integrated circuits on computer boards are sensitive to static elect ricity. To avoid damaging chips from electrostatic dischar ge, observe the followin g precautions:



Do not remove boards or integrated circuits from their anti-static packaging until you are ready to install them .

 Before handling a board or integrated circuit, touch an unpainted portion of

the system unit chassis for a few seco nds. This helps to discharge any static electricity on your body.



Wear a wrist-grounding strap, available from most electronic component stores, when handling bo ards and co mponents. Fasten the ALL IGATOR clip of the strap to the end of the shielded wire lead from a grounded object. Please wear and connect the strap before handle the HS-4655 to ensure harmlessly discharge any static electricity through the strap.



Please use an anti-static pad when putting dow n any components or parts or tools outside the computer. You may also use an anti-static bag instead of the pad. Please inquire from your local supplier for additional assistance in finding the necessary anti-static gadgets.

NOTE:

DO NOT TOUCH THE BOARD OR ANY OTHER SENSITIVE COMPONENTS WITHOUT ALL NECESSARY ANTI-STATIC PROTECTIONS.

Page 6

Page 7

Chapter 1

General Description

The HS-4655 is a VIA VT8606 chipset-based b oard designed for VIA Eden 667MHz low power embedded CPU. These features combine and make the HS-4655 an ideal all-in-one industrial single board computer. Additional features include an enhanced I/O with CRT/LVDS Panel, dual LAN, audio, TV-Out, 8 COM, and USB2.0 ports interfaces.

Its onboard ATA/33/66/100 to IDE drive interface architecture allows the HS-4655 to support data transfers of 33, 66 or 100MB/sec . to one IDE drive connection. Designed with the VIA VT8606 core logic chipset, the board supports VIA Eden 66 7MHz low power embedded CPU. The VIA VT8606 with 32MB shared main memory supporting CRT/Panel displays.

System memory is also sufficient with the two SO-DIMM sockets that can support up to 1GB.

Additional onboard connectors inc lude two USB1.1 and two USB2.0 ports providing faster data transmission, and two external RJ-45 connectors for 10/100 Based Ethernet use.

Page 8

To ensure the reliability in an unmanned or standalone system

, the

Watchdog Timer (WDT) onboard HS-4655 is designed with pure hardware that does not need the arithmetical functions of a real-time clock chip. If any program causes unexpected halts to the system, the onboard Watchdog Timer (WDT) will automatically reset the CPU or generate an interrupt to resolve such condition.

1.1 Major Features

The HS-4655 comes with the following features:

 VIA Eden 667MHz low power embedded CPU  Supports 100/133MHz FSB  Two SO-DIMM sockets with a max. capacity of 1GB  VIA VT8606/VT82C686B system chipset  VIA VT82C686B, SMC 37C669, XR17D154CV super I/O chipset  VIA VT8606 garphics controller  LVDS Panel display interface  Dual RealTek RTL8100BL Ethernet controller  AC97 3D audio controller  Fast PCI ATA/33/66/100 IDE controller  CompactFlash card adapter, eight COM, four USB, PC/104 connector  TV-Out function  Hardware Monitor function

Page 9

1.2 Specifications



CPU: VIA Eden 667MHz low power embedded CPU



Memory: Two SO-DIMM sockets supporting up to 1GB



Chipset: VIA VT8606/VT82C686B



I/O Chipset: VIA VT82C686B, SMC 37C669, XR17D154CV



CompactFlash: One, Type II IDE interface adapter



PCI Slot: One, Type I mini PCI slot



VGA: VIA VT8606 with 32MB shared main memory supporting CRT/Panel displays up to 1280 x 1024 at 24bpp colors(CRT)/1024 x 768 at 18bpp colors(Panel)



LVDS Panel: Supports 18-bit single channel/36-bit dual channel LVDS interface

 TV-Out: Supports PAL or NTSC TV systems  LAN: Dual RealTek RTL8100BL 10/100 Based LAN  Audio: AC97 3D audio controller  IDE: Two IDE disk drives supporting ATA/33/66/100 and with transfer

rates of up to 33/66/100MB/sec.



FDD: Supports up to two floppy disk drives



Parallel: One enhanced bi-directional parallel port supporting SPP/ECP/EPP

 Serial Port: 16C550 UART-compatible RS-232/422/485 x 2 and RS-232

x 6 serial ports with 16-byte FIFO



PC/104: PC/104 Bus connector for 16-bit ISA Bus



USB: Two internal USB1.1 and two internal USB2.0 ports



Keyboard/Mouse: PS/2 6-pin Mini DIN or 6-pin header



BIOS: AMI PnP Flash BIOS



Watchdog Timer: Sets 1/2/10/20/110/220 seconds, activity trigger with Reset or NMI

 CMOS: Battery backup  Temperature: 0~+60°C (operating)  Hardware Monitor: VIA VT82C686B  Board Size: 20.3(L) x 10.2(W ) cm

Page 10

1.3 Board Dimensions

Page 11

Chapter 2

Unpacking

2.1 Opening the Delivery Package

The HS-4655 is packed in an anti-static bag. The board has components that are easily damaged by static electricity. Do not remove the anti-static wrapping until proper precautions have been taken. Safety Instructions in front of this manual describe anti-static precautions and procedures.

2.2 Inspection

After unpacking the board, plac e it on a raised surface and carefu lly inspect the board for any damage that might have occurred during shipment. Ground the board and exercise extreme care to prevent damage to the board from static electricity.

Integrated circuits will sometimes come out of their sockets during shipment. Examine all integrated circuits, particularly the BIOS, processor, memory modules , R OM -D i sk , and keyboard controller chip to ensure that they are firmly seated. The HS-4655 delivery package contains the following items:



HS-4655 Board x 1

 Utility CD Disk x 1 

Cable Package x 1

 Jumper Bag x 1



User’s Manual

Page 12

Cables Package

NO. Description

1 ATA/100 IDE flat cable x 1 2 MIC/Audio 8-pin cable with bracket x 1 3 Floppy flat cable x 1 4 PS/2 KB/MS transfer cable x 1 5 Parallel port flat cable x 1 6 8-pin USB split type cable with bracket x 1 7 VGA flat cable x 1 8 9 Four COM flat cable by 2.0pitch x 1

Four COM flat cable by 2.54pitch x 1

It is recommended that you keep all the parts of the delivery package intact and store them in a safe/dry place for any unforeseen event requiring the return shipment of the product. In case you discover any missing and/or damaged items from the list of items, please contact your dealer immediately.

Page 13

Chapter 3

Hardware Installation

This chapter provides the inform ation on how to install the hardware using the HS-4655. This chapter also c ontains information related to jumper settings of switch, watchdog timer, and the DiskOnChip™ address selection etc.

3.1 Before Installation

After confirming your package contents, you are now ready to install your hardware. The following are important reminders and steps to take before you begin with your installation process.

1. Make sure that all jumper settings match their default settings and CMOS setup correctly. Refer to the sections on this chapter for the default settings of each jumper.

2. Go through the con nections of all external devices a nd m ake sure that they are installed properly and configured correctly within the CMOS setup. Refer to the sections on thi s chapter for the detailed information on the connectors.

3. Keep the man u a l and diskette in good condition for future reference and use.

Page 14

3.2 Board Layout

Page 15

3.3 Jumper List

Jumper Default Setting Setting Page

J2(1-6) WDT Timer Select: 1sec. Short 1-2, 3-4, 5-6 22

JP30 Panel Voltage Select: +3.3V Short 1-2 11 JP31 WDT Active Type Setting: Disabled All Open 22 JP32

JP8/JP12

JP15/JP20

JP9/JP13 JP16/JP21 JP22/JP24 JP26/JP28 JP23/JP25 JP27/JP29

JP14 JP17

JP10 JP18

JP11 JP19

JP2 JP3

JP14/ JP17

JP10/JP18

JP11/JP19

JP2/JP3

JP4~JP7 Debug Only All Open 15

Clear CMOS: Normal Operation Short 1-2 20 COM3 Use RS-232 or RS-422/485 Select: RS-232 COM4 Use RS-232 or RS-422/485 Select: RS-232 COM7 Use RS-232 or RS-422/485 Select: RS-232 COM8 Use RS-232 or RS-422/485 Select: RS-232 COM3 Use RS-422/485 full duplex

COM4 Use RS-422/485 full duplex

COM7 Use RS-422/485 full duplex

COM8 Use RS-422/485 full duplex

COM3 COM4 Use RS-422/485 half duplex

COM7 COM8 Use RS-422/485 half duplex

Short 1-2 15

Short 1-2 15 Short 1-2

Open *

Short 1-2

Open *

Short 1-2

Open *

Short 1-2

Open *

Short 2-3

Short 2-3 Short 2-3

Short 2-3

Example:

1. Set COM3 as RS232, to short 1-2 for JP8, JP12, JP15, JP20; total 4 jumpers.

2. Set COM3 as RS422/485 full duplex, to short 2-3 for JP8, JP12, JP15, JP20; to short 1-2 for JP14; to open for JP17; total 6 jumpers.

3. Set COM3 as RS422/485 half duplex, to short 2-3 for JP8, JP12, JP15, JP20; to short 2-3 for JP14, JP17; total 6 jumpers.

Page 16

RS232 & RS422/485 can use either one at same time for COM3,

COM4, COM7, COM8

3.4 Connector List

Connector Definition Page

ATXPR1 20-pin ATX Power In Connector 20

CN1 COM 1 Connector (5x2 header) 15 CN2 COM 2 Connector (5x2 header) 15 CN3 COM 3 Connector (5x2 header) 15 CN4 COM 4 Connector (5x2 header) 15 CN5 COM 5 Connector (5x2 header) 15 CN6 COM 6 Connector (5x2 header) 15 CN7 COM 7 Connector (5x2 header) 15 CN8 COM 8 Connector (5x2 header) 15 CN9 Line In/Audio Out Connector 28

CN10/CN11 RS-422/485 Connector (5x2 header) 15

CN13 FDC Connector 14 CN14 CN15 PS/2 6-pin Mini DIN KB/MS Connector 21 CN16 Internal CRT Connector (5x2 header) 11 CN17 PC/104 40-pin Connector 26 CN18 PC/104 64-pin Connector 26 CN19 CN20 50-pin Panel Connector 11

CN21/CN22 LVDS Connector 11

CN23 CompactFlash Connector 28 CN24 6-pin KB/MS Connector

CN25/CN26 RJ-45 Connectors

DM1 SO-DIMM Socket 11

FN1 Fan Connector 20

J1 IDE Connector 13 J3 S-Video Connector 29

JP33 System Front Panel Connector 21

PCI Mini PCI Connector 24

PCI1 PCI Slot 30

USB1/USB2

Parallel Connector 15

RCA Connector 29

USB Connector 19

Page 17

3.5 Configuring the CPU

The HS-4655 embedded with a VIA Eden 667MHz low power CPU. User don’t need to adjust the frequently and check spee d of VIA Eden CPU.

3.6 System Memory

The HS-4655 provides two SO-DIMM sockets at locations DM1/DM2. The maximum capacity of the onboard memory is 1GB.

3.7 VGA Controller

The HS-4655 provides three connection methods of a VGA device. CN16 offers an internal CRT connecto r while CN20 is the 50-pin panel connector and CN21/CN22 are the LVDS interface connectors onboard reserved for flat panel installation.



CN16: Internal CRT Connector

PIN Description PIN Description

1 Red 2 GND 3 Green 4 GND 5

Blue

7 HSYNCB 8 DCSDA 9 VSYNCB 10 DCSCL



CN21/CN22: LVDS Interface Connector

PIN Description PIN Description

1 V 3 GND 4 GND 5 Y0M/Z0M 6 Y0P/Z0P 7

9 Y2M/Z2M 10 Y2P/Z2P 11 YCM/ZCM 12 ZCP/ZCP 13 N/C 14 N/C

2 V

LCD

Y1M/Z1M

Y1P/Z1P

GND

LCD

1413

Page 18



CN20: 50-pin Panel Connector

PIN. Description PIN

+12V

6 ENAVDD

LCD

PD2

P32

NOTE:

1 3 GND 4 GND 5 V 7 ENAVEE 8 GND 9 PD0 10 PD1

11 13 PD4 14 PD5 15 PD6 16 PD7 17 PD8 18 PD9 19 PD10 20 PD11 21 PD12 22 PD13 23 PD14 24 PD15 25 PD16 26 PD17 27 PD18 28 PD19 29 PD20 30 PD21 31 PD22 32 PD23 33 PD24 34 PD25 35 SHFCLK 36 FLM 37 39 GND 40 ENPBLT 41 P26 42 P27 43 P28 44 P29 45 P30 46 P31 47 49 P34 50 P35

Please set the proper voltage of your panel using JP30 before proceeding on installing it.

Description

+12V

PD3

P33

Page 19

The HS-4655 has an onboard jumper that selects the working voltage of the flat panel connected to the system. Jumper JP30 offers two voltage settings for the user.



JP30: Panel Voltage Select

Options Settings

+3.3V (default) Short 1-2

+5V Short 2-3

3.8 PCI E-IDE Drive Connector

CN23 is a standard 44-pin 2.0mm pitch connector dais y-chain driver connector serves the PCI E-IDE drive provisions onboard the HS-4655. A maximum of two ATA/33/66/100 IDE drives can be connected to the HS-4655 via J1.



J1: IDE Connector

PIN Description PIN Description

1 Reset 2 GND 3 DATA7 4 DATA 8 5 DATA 6 6 DATA 9 7 DATA 5 8 DATA 10

9 DATA 4 10 DATA 11 11 DATA 3 12 DATA 12 13 DATA 2 14 DATA 13 15 DATA 1 16 DATA 14 17 19 GND 20 N/C 21 PDREQ 22 GND 23 IOW# 24 GND 25 IOR# 26 GND 27 29 RPDACK# 30 GND 31 IRQ14 32 N/C 33 RPDA1- 34 DATA66 35 RPDA0- 36 RPDA2- 37 PPCS1- 38 RPCS3- 39 HDD Active 40 GND

DATA 0

PIORDY

DATA 15

RP1PD1-

Page 20

3.9 Floppy Disk Drive Connector

The HS-4655 uses a standard 34-pin header connector, CN13, for floppy disk drive connection. A total of two FDD drives may be connected to CN13 at any given time.



CN13: FDC Connector

PIN Description PIN Description

1 GND 2 DRVDEN0 3 GND 4 N/C 5 7 GND 8 INDEX#

9 GND 10 MTR0# 11 GND 12 DS1# 13 GND 14 DS0# 15 GND 16 MTR1# 17 GND 18 DIR# 19 GND 20 STEP# 21 GND 22 WDATA# 23 GND 24 WGATE# 25 GND 26 TRAK00# 27 GND 28 WRTPRT# 29 GND 30 RDATA# 31 33 GND 34 DSKCHG#

GND

DRVDEN1

HDSEL#

Page 21

3.10 Parallel Connector

CN14 is a standard 26-pin flat cable connector deigned to accommodate parallel port connection on the HS-4655.



CN14: Parallel Connector

PIN Description PIN Description

1 Strobe 14 Auto Form Feed 2 DATA 0 15 ERROR# 3

DATA 1

4 DATA 2 17 Printer Select LN# 5 DATA 3 18 GND 6 DATA 4 19 GND 7 DATA 5 20 GND 8

DATA 6

9 DATA 7 22 GND 10 Acknowledge 23 GND 11 Busy 24 GND 12 Paper Empty 25 GND 13

Printer Select

Initialize

GND

3.11 Serial Port Connectors

The HS-4655 offers two NS16C550 compatible UARTs with Read/Receive 16-byte FIFO serial ports and eig ht internal 10-pin headers and two RS-422/485 connectors.



CN1: COM1 Connector (5x2 Header)

PIN Description PIN Description

1 DCD1 2 DSR1 3 RXD1 4 RTX1 5 TXD1 6 CTX1 7 DTR1 8 RI1 9 GND 10 VCC

DCD1

RXD1

TXD1

DTR1

GND

DSR1

RTX1

CTX1

RI1

VCC

Page 22



CN2: COM2 Connector (5x2 Header)

PIN Description PIN Description

1 DCD2 2 DSR2 3 RXD2 4 RTX2 5 TXD2 6 CTX2 7 DTR2 8 RI2 9

GND



CN3: COM3 Connector (5x2 Header)

PIN Description PIN Description

1 DCD3 2 DSR3 3 RXD3 4 RTX3 5 TXD3 6 CTX3 7 DTR3 8 RI3 9 GND 10 VCC



CN4: COM4 Connector (5x2 Header)

PIN Description PIN Description

1 DCD4 2 DSR4 3

RXD4

5 TXD4 6 CTX4 7 DTR4 8 RI4 9 GND 10 VCC



CN5: COM5 Connector (5x2 Header)

PIN Description PIN Description

1 DCD5 2 DSR5 3 RXD5 4 RTX5 5 TXD5 6 CTX5 7 DTR5 8 RI5 9 GND 10 VCC

VCC

RTX4

DCD2

RXD2

TXD2

DTR2

GND

DCD3

RXD3

TXD3

DTR3

GND

DCD4

RXD4

TXD4

DTR4

GND

DCD5

RXD5

TXD5

DTR5

GND

DSR2

RTX2

CTX2

RI2

VCC

DSR3

RTX3

CTX3

RI3

VCC

DSR4

RTX4

CTX4

RI4

VCC

DSR5

RTX5

CTX5

RI5

VCC

Page 23



CN6: COM6 Connector (5x2 Header)

PIN Description PIN Description

1 DCD6 2 DSR6 3 RXD6 4 RTX6 5 TXD6 6 CTX6 7 DTR6 8 RI6 9 GND 10 VCC



CN7: COM7 Connector (5x2 Header)

DCD6

RXD6

TXD6

DTR6

GND

PIN Description PIN Description

1 DCD7 2 DSR7 3 RXD7 4 RTX7 5 TXD7 6 CTX7 7

DTR7

9 GND 10 VCC



CN8: COM8 Connector (5x2 Header)

RI7

DCD7

RXD7

TXD7

DTR7

GND

PIN Description PIN Description

1 DCD8 2 DSR8 3 RXD8 4 RTX8 5 TXD8 6 CTX8 7 DTR8 8 RI8 9 GND 10 VCC



CN10: RS-422/485 Connector (5x2 Header, COM3 &COM4)

DCD8

RXD8

TXD8

DTR8

GND

PIN Description PIN Description

1 -TX1 2 +TX1 3

+RX1

-RX1

5 GND 6 N/C 7 -TX2 8 +TX2 9 +TX2 10 -RX2

-TX1

+RX1

GND

-TX2

+RX2

DSR6

RTX6

CTX6

RI6

VCC

DSR7

RTX7

CTX7

RI7

VCC

DSR8

RTX8

CTX8

RI8

VCC

+TX1

-RX1

N/C

+TX2

-RX2

Page 24



CN11: RS-422/485 Connector (5x2 Header, COM7 &COM8)

PIN Description PIN Description

-TX7

3 +RX7 4 -RX7 5 GND 6 N/C 7 -TX8 8 +TX8 9 +TX8 10 -RX8



JP8/JP12/JP15/JP20: COM3 use RS-232 or RS-422/485

+TX7

-TX7

+RX7

GND

-TX8

+RX8

Select

Options Settings

RS-232 (default) Short 1-2

RS-422/485



JP9/JP13/JP16/JP21: COM4 use RS-232 or RS-422/485

Short 2-3

Select

Options Settings

RS-232 (default) Short 1-2

RS-422/485 Short 2-3



JP22/JP24/JP26/JP28: COM7 use RS-232 or RS-422/485

Select

Options Settings

RS-232 (default)

RS-422/485 Short 2-3

Short 1-2

+TX7

-RX7

N/C

+TX8

-RX8

Page 25



JP23/JP25/JP27/JP29: COM8 use RS-232 or RS-422/485 Select

NOTE:

Options Settings

RS-232 (default) Short 1-2

RS-422/485 Short 2-3

RS-422/485 port uses C OM3/COM 4 and COM7/ COM8. RS-23 2 of COM3/COM4 and COM7/COM8 cannot be used while RS-422/485 is selected.

3.12 Ethernet Connector

The HS-4655 provides two external RJ-4 5 connec tors. Pleas e refer to the following for its pin information.



CN25/CN26: RJ-45 Connector

PIN Description PIN Description

1 TX+ 2 TX- 3 RX+ 4 R/C GND 5 R/C GND 6 RX- 7 R/C GND 8 R/C GND

R/C GND

TX-

RX-

TX+

RX+

R/C GND R/C GND

3.13 USB Connector

The HS-4655 provides TWO 8-pin connectors, at location USB1/USB2, for four USB ports to the HS-4655.

Page 26



USB1/USB2: USB Ports

PIN Description PIN Description

1 3 BD0-/BD2- 4 BD1-/BD3- 5 BD0+/BD2+ 6 BD1+/BD3+ 7 GND 8 GND

VCC

3.14 CMOS Data Clear

The HS-4655 has a Clear CMOS jumper on JP32.



JP32: Clear CMOS

Options Settings

Normal Operation (default) Short 1-2

Clear CMOS Short 2-3

IMPORTANT:

Before you turn on the power of your system, please

set JP32 to Short 1-2 for normal operation.

3.15 Power and Fan Connectors

HS-4655 provides one 20-pin power co nnectors at ATXPR1. And one 3-pin fan power in at FN1.



ATXPR1: 20-pin ATX Power In Connector

PIN Description PIN Description

1 3.3V 11 3.3V 2 3.3V 12 -12V 3 GND 13 GND 4 +5V 14 PS_ON 5 GND 15 GND 6 +5V 16 GND 7 GND 17 GND 8 N/C 18 -5V 9 5VSB 19 +5V

10 +12V 20 +5V

111

10 20

Page 27



FN1: Fan Connector

PIN Description

1 GND 2 +5V 3 CPU Fan1

3.16 Keyboard/Mouse Connectors

The HS-4655 offers one possibilities for keyboard/mouse connection. The connection are via CN15 for an external PS/2 type keyboard/mouse.



CN15: PS/2 6-pin Mini DIN Keyboard/Mouse Connector

PIN Description

1 2 Mouse Data 3 GND 4 +5V 5 6 Mouse Clock



CN24: 6-pin KB/MS Connector

Keyboard Data

Keyboard Clock

PIN Description

1 KB DATA 2 KB CLK 3 MS DATA 4 VCC 5 GND 6 MS CLK

Keyboard

Clock

Mouse

Clock

GND

Keyboard

Data Mouse

Data +5V

3.17 System Front Panel Connectors

The HS-4655 has one LED at location JP33 that indicates the power-on status. This visual feature of the IDE LED may also be connected to an external IDE LED, Speaker, Reset Switch, Power LED, EXT SMI, Power Button, and SLP Button via connector

JP3(13-15), JP3(1-3-5-7) , JP3(9-11), JP3(2-4), JP3(6-8), JP3(10-12), JP3(14-16).

Page 28



JP33: System Front Panel Connector

PIN Description PIN Description

+5V

3 GND 4 GND 5 N/C 6 EXT SMI 7 Speaker 8 GND 9 GND 10 PW Button

Reset Switch

11 13 330Ω Pull +5V 14 SLP Button 15 HDD LED 16 GND

330Ω Pull +5V

GND

Connector JP33 Orientation

SPEAKER

RST_SW

HD_LED

PWR LED

EXT_SMI

PWR button

SLP button

3.18 Watchdog Timer

There are three access cycles of Watchdo g Timer as Enab le, Refresh and Disable. The Enable cycle proceeds via READ PORT 443H whereas the Disable cycle proceeds via READ PORT 045H. A continued Enable cycle after a first Enable cycle means Refresh.

Once the Enable cycle is active, a Refresh cycle is reque sted before the time-out period. This restar ts counting of the WDT period. Wh en the time counting goes over the preset period of WDT, it will assume that the program operation is abnormal. A System Reset signal to re-start or a NMI cycle to the CPU transpires when such error happens. Jumper JP31 is used to select the function of Watchdog Timer.



JP31: Watchdog Timer Active Type Setting

Options Settings

Active NMI Short 1-2

System Reset Short 2-3

Disabled WDT (default) Open

Page 29



J2(1-6): WDT Timeout Period Select

Period PINS 1-2 PINS 3-4 PINS 5-6

1 sec (default)

2 sec Open Short Short 10 sec Short Open Short 20 sec Open Open Short

110 sec Short Short Open 220 sec

Short Short Short

Open Short Open

The Watchdog Timer is disabled after the system Power-On . It can be enabled via an Enable cycle and reading the control port (443H), or via a Refresh cycle and reading the control port (443H), or via a Disable cycle and reading the disable control port (045H).

After an Enable cycle of WDT, user must immediately execute a Refresh cycle to WDT before its peri od setting c omes to an en d ever y 1, 2, 10, 20, 110 or 220 seconds. If the Refresh cycle does not activate before WDT period cycle, the onboard WDT architecture will issue a Reset or NMI cycle to the system. There are three I/O ports that control the Watchdog Timer.

443H I/O Read The Enable cycle 443H I/O Read The Refresh cycle 045H I/O Read The Disable cycle

The following sample program shows how to Enable, Disable and Refresh the Watchdog Timer:

WDT_EN_RF EQU 0443H WDT_DIS EQU 0045H

WT_Enable PUSH AX ; keep AX DX PUSH DX MOV DX,WDT_EN_RF ; enable the WDT IN AL,DX POP DX ; get back AX, DX POP AX RET

WT_Refresh PUSH AX ; keep AX, DX PUSH DX MOV DX,WDT_ET_RF ; refresh the WDT IN AL,DX POP DX ; get back AX, DX POP AX RET

Page 30

WT_DISABLE PUSH AX PUSH DX MOV DX,WDT_DIS ; disable the WDT IN AL,DX

POP DX ; get back AX, DX POP AX RET

3.19 Mini PCI Connector

HS-4655 supports a Mini PCI connector. The peripheral component with standard Type1 Mini PCI can be used. For particular requirement, please refer to “BOSER Mini PCI series product” on website or contact with us.



PCI: Mini PCI Connector

PIN Description PIN Description

1 INTA# 2 VCC 3 VCC3 4 INTD# 5 7 GND 8 N/C

9 CLK 10 RST# 11 GND 12 VCC3 13 REQ# 14 GNT# 15 17 AD[31] 18 PME# 19 AD[29] 20 GNT1 21 GND 22 AD[30] 23 AD[27] 24 VCC3 25 AD[25] 26 AD[28] 27 REQ1 28 AD[26] 29 C/BE[3]# 30 AD[24] 31 AD[23] 32 AD[21] 33 GND 34 GND 35 AD[21] 36 AD[22] 37 AD[19] 38 AD[20] 39 GND 40 PAR 41 43 C/BE[2]# 44 AD[16] 45 IRDY# 46 GND 47 VCC3 48 FRAME#

INTB#

VCC3

AD[17]

. . . More on next page . . .

INTB#

GND

AD[18]

Page 31

PIN Description PIN Description

49 N/C 50 TRDY# 51 SERR# 52 STOP# 53 55 PERR# 56 DEVSEL# 57 C/BE[1]# 58 GND 59 AD[14] 60 AD[15] 61 GND 62 AD[13] 63 AD[12] 64 AD[11] 65 AD[10] 66 GND 67 GND 68 AD[9] 69 AD[8] 70 C/BE[0]# 71 AD[7] 72 VCC3 73 VCC3 74 AD[6] 75 77 REQ2 78 AD[2] 79 AD[3] 80 AD[0] 81 VCC 82 GNT2 83 AD[1] 84 GNT3 85 GND 86 GND 87 N/C 88 M66EN 89 N/C 90 N/C 91 N/C 92 N/C 93 N/C 94 N/C 95 N/C 96 N/C 97 99 N/C 100 N/C

GND

AD[5]

N/C

VCC3

AD[4]

RESERVED

199

Mini PCI Socket

pin orientation

100

Page 32

3.21 PC/104 Connectors

The PC/104 expansion bus offers provisions to connect all types of PC/104 modules. With the PC/104 bus being known as the new generation of industrial embedded 16-bit PC standard bus, thou sands of PC/104 modules from multiple venders can be easily installed onboard. The detailed pin assignme nt of the PC/104 expansion bus connectors CN17 and CN18 are listed on the following tables:

NOTE：



PIN Description PIN Description

10 DRQ0 30 -MEMR 11 -DACK5 31 -MEMW 12 DRQ5 32 SD8 13 -DACK6 33 SD9 14 DRQ6 34 SD10 15 16 DRQ7 36 SD12 17 +5V 37 SD13 18 -MASTER 38 SD14 19 GND 39 SD15 20 GND 40 N/C

The PC/104 connector allows direct plugging or stack-through piling of PC/104 modules without requiring the PC/104 mounting kit.

CN17: PC/104 40-pin Connector

Connector diagram

1 GND 21 GND 2 -MEMCS16 22 -SBHE 3 4 IRQ10 24 LA22 5 IRQ11 25 LA21 6 IRQ12 26 LA20 7 IRQ15 27 LA19 8 9 -DACK0 29 LA17

-IOSC16

IRQ14

-DACK7

LA23

LA18

SD11

rotated 90 degrees

clockwise from

original position

121

Page 33



CN18: PC/104 64-pin Connector

PIN Description PIN Description

1 -IOCHECK 33 GND 2 SD7 34 RESETDRV 3 SD6 35 +5V 4 SD5 36 IRQ9 5 SD4 37 N/C 6 SD3 38 N/C 7 SD2 39 -12V 8 SD1 40 OWS 9

10 IOCHRDY 42 GND 11 AEN 43 -SMEMW 12 SA19 44 -SMEMR 13 SA18 45 -IOW 14 SA17 46 -IOR 15 SA16 47 -DACK3 16 SA15 48 DRQ3 17 SA14 49 -DACK1 18 SA13 50 DRQ1 19 SA12 51 -REFRESH 20 SA11 52 SYSCLK 21 22 SA9 54 SLPBTN 23 SA8 55 IRQ5 24 SA7 56 IRQ4 25 SA6 57 IRQ3 26 SA5 58 N/C 27 SA4 59 TC 28 29 SA2 61 +5V 30 SA1 62 OSC 31 SA0 63 N/C 32 GND 64 GND

SD0

SA10

SA3

+12V

IRQ7

BALE

Connector diagram

rotated 90 degrees

clockwise from

original position

133

6432

Page 34

3.21 Audio Connectors

The HS-4655 has an onboard AC97 3D audio interfac e. The following tables list the pin assignments of the Line In/Audio Out connector.



CN9: Line In/Audio Out Connector

PIN Description PIN Description

1 AOUTL 2 AOUTR 3 5 MIC IN 6 LI_L 7 GND 8 GND

GND

LI_R

3.23 CompactFlash™ Connector

The HS-4655 also offers an option al CompactFlash™ connector which is IDE interface located at the solder side of the board (beneath the SO-DIMM connector). The designated CN23 connector, once soldered with an adapter, can hold CompactFlash™ cards of various sizes. Please turn off the power before inserting the CD card.



CN23: CompactFlash™ Connector

PIN Description PIN Description

1 GND 2 DATA 3 3 DATA 4 4 DATA 5 5 DATA 6 6 DATA 7 7

9 GND 10 GND 11 GND 12 GND 13 VCC 14 GND 15 GND 16 GND 17 19 SDA1 20 SDA0 21 DATA 0 22 DATA 1 23 DATA 2 24 470Ω pull to GND 25 N/C 26 N/C 27 DATA 11 28 DATA 12 29 DATA 13 30 DATA 14 31 DATA 15 32 SDCS3#

SDCS1#

GND

. . . More on next page . . .

GND

SDA2

Page 35

PIN Description PIN Description

33 N/C 34 IOR 35 IOW 36 EWE0 37 IRQ 38 VCC 39 CS 40 N/C 41 Reset 42 IORDY 43 DACK 44 REQ 45 IDE LED 46 PDIAG 47 DATA 8 48 DATA 9 49 DATA 10 50 GND

Inserting a CompactFlash™ card into the adap ter is not a difficult task . The socket and card are both keyed and there is only one direction for the card to be completely inserted. Refer to the diagram on the following page for the traditional way of inserting the card.

tFla

Com

3.23 TV-Out Connector

HS-4655 can support TV-Out function which input could be up to 800 x 600 graphics resolutions. World Wide Video stand ards are supported including NTSC-M (North America, Ta iwan), NTSC-J ( Japan), PAL-B, D, G, H, I (Europe, Asia), PAL-M (Brazil), PAL-N (Uruguay, Paraguay) and PAL-NC (Argentina).



CN19: RCA Connector (for TV-Out function)

PIN Description

1 CVBS 2 GND

Page 36



J3: S-Video Connector

PIN Description

1 C 2 GND 3 Y 4 GND

3.24 PCI Expansion Slot

HS-4655 provides one standard PCI expansion slot at PCI1.

Page 37

Chapter 4

AMI BIOS Setup

The HS-4655 uses AMI BIOS for the system configuration. The AMI BIOS setup program is designed to provide the maximum flexibility in configuring the system by offering various options that could be selected for end-user requirements. This chapter is written to assist you in the proper usage of these features.

4.1 Starting Setup

The AMI BIOS is immediately activated when you first power on the computer. The BIOS reads the system information contained in the CMOS and begins the process of checking out the system and configuring it. When it finishes, the BIOS will seek an operating system on one of the disks and then launch and turn control over to the operating system.

While the BIOS is in control, the Setup program can be activated in one of two ways:

1. By pressing <Del> immediately after switchin g th e system on, or

2. By pressing the <Del> key when the following message appears briefly at the bottom of the screen during the POST (Power On Self Test).

Press DEL to enter SETUP.

If the message disappears before you respond and you still wish to enter Setup, restart the system to try again by turning it OFF then ON or pressing the "RESET" button on the system case. You may also restart by simultaneously pressing <Ctrl>, <Alt>, and <Delete> keys. If you do not press the keys at the correct time and the system does not boot, an error message will be displayed and you will be asked to...

PRESS F1 TO CONTINUE, DEL TO ENTER SETUP

Page 38

4.2 Using Setup

In general, you use the arrow keys to highlight items, press <Enter> to select, use the <PageUp> and <Page Down> keys to chang e entries, and press <Esc> to quit. The following table provides more detail about how to navigate in the Setup program using the keyboard.

Move to previous item

↑ ↓ Move to next item

Move to previous item

← → Move to previous item

Esc key Main Menu -- Quit and not save changes into CMOS

Status Page Setup Menu and Option Page Setup Menu -Exit current page and return to Main Menu

PgUp key Decrease the numeric value or make changes PgDn key

+ key Increase the numeric value or make changes

- key Decrease the numeric value or make changes F1 key Reserved F2 key Change color from total 8 co lors. F2 to select color forward F3 key F2 to select color backward F4 key Reserved F5 key Reserved F6 key Reserved F7 key Reserved F8 key Reserved F9 key Reserved

F10 key

Increase the numeric value or make changes

Save all the CMOS changes, only for Main Menu

Page 39

4.3 Main Menu

Once you enter the AMI BIOS CMOS Setup Utility, the Main Menu will appear on the screen. The Main Menu allows you to select from several setup functions and two exit choices. Use the arrow keys to select among the items and press <Enter> to enter the sub-menu.

AMIBIOS HIFLEX SETUP UTILITY – VERSION x.xx

Standard CMOS Setup

Advanced CMOS Setup

Advanced Chipset Setup

Power Management Setup

PCI / Plug and Play Setup

Peripheral Setup

Hardware Monitor Setup

Auto-Detect Hard Disks

Change User Password

Change Supervisor Password

Auto Configuration with Optimal Settings

Auto Configuration with Fail Safe Settings

Save Settings and Exit

Exit Without Saving

Standard CMOS setup for changing time, date, hard disk type, etc.

NOTE:

ESC:Exit :Sel F2/F3: Color F10: Save & Exit

A brief description of the highli ghted choice appears at the bottom of the screen.

Page 40

4.4 Standard CMOS Setup

The Standard Setup is used for the basic hardware system configuration. The main function is for Data/Time and Floppy/Hard Disk Drive settings. Please refer to the following screen for the setup. When the capacity of the IDE hard disk drive is larger than 528MB, you must set the HDD mode to BIOS SETUP to install the HDD correctly.

mode. Please use the IDE Setup Utility in

LBA

AMIBIOS SETUP – STANDARD CMOS SETUP

Date (mm/dd/yyyy) : Thu Apr 17, 2003 Base Memory : Time (hh/mm/ss) : 19:04:12 Extd Memory :

Floppy Drive A: 1.44MB, 3 1/2 Floppy Drive B: Not Installed

Type Size Cyln Head WPcom Sec Pri Master : Auto On Pri Slave : Auto On Sec Master : Auto On Sec Slave : Auto On

Boot Sector Virus Protection: Disabled

Month: Jan - Dec ESC: Exit : Sel

Day: 01 - 31 PgUp/PgDn: Modify

Year: 1980 - 2099 F2/F3: Color

LBA Mode

Blk Mode

PIO Mode

639KB

247MB

32Bit Mode

Page 41

4.5 Advanced CMOS Setup

This section allows you to configure your system for the basic operation. You have the opportunity to select the system’s default speed, boot-up sequence, keyboard operation, shadowing and security.

Quick Boot Enabled S Available Options: Primary Master ARMD Emulated as Auto Primary Slave ARMD Emulated as Auto Secondary Master ARMD Emulated as Auto Secondary Slave ARMD Emulated as Auto 1st Boot Device Floppy 2nd Boot Device IDE-0 3rd Boot Device CD-ROM Try Other Boo t Devices Yes S.M.A.R.T. for Hard Disks Disabled BootUp Num-Lock On Floppy Drive Swap Disabled Floppy Drive Seek Disabled PS/2 Mouse Support Enabled Primary Display VGA/EGA Password Check Setup Boot To OS/2 No CPU MicroCode Updation Enabled CPU Serial Number Enabled L1 Cache Enabled L2 Cache Enabled System BIOS Cacheable Enabled C000,32k Shadow Cached C800,16k Shadow Disabled CC00,16k Shadow Disabled D000,16k Shadow Disabled D400,16k Shadow Disabled D800,16k Shadow Disabled DC00,16k Shadow Disabled T F2/F3: Color

AMIBIOS SETUP – ADVANCED CMOS SETUP

` Disabled

Enabled

ESC: Exit PgUp/PgDn: Modify



: Sel

Page 42

4.6 Advanced Chipset Setup

This section allows you to configure the system based on the specific features of the installed ch ipset. This chipset m anages bus speeds an d the access to the system memory resources, such as DRAM and the external cache. It also coordinates the communications between the conventional ISA and PCI buses. It must be stated that these items should never be altered. The default settings have been chosen because they provide the best oper ating conditions for your system. You might consider and make any changes only if you discover that the data has been lost while using your system.

AMIBIOS SETUP – ADVANCED CHIPSET SETUP

******** DRAM Timing ******** Available Options:

Configure SDRAM Timing by SPD Disabled ` Disabled DRAM Frequency 100Mhz Enabled SDRAM CAS# Latency 3

DRAM Bank Interleave Enabled

Memory Hole Disabled

AGP Mode 4x

AGP Fast Write Disabled

AGP Aperture Size 64MB

AGP Master 1 W/S Write Disabled

AGP Master 1 W/S Read Disabled

Search for MDA Resources Yes

PCI Delay Tr ansaction Enabled

ISA Bus Clock PCICLK/4

USB Controller All USB Port

USB Device Legacy Support Disabled ESC: Exit

Port 64/60 Emulation Disabled PgUp/PgDn: Modify

ATX Power Supply Disabled F2/F3: Color



: Sel

Page 43

4.7 Power Management Setup

The Power Management Setup allows user to configure the system for saving energy in a most effective way while operating in a manner consistent with his own style of computer use.

AMIBIOS SETUP – POWER MANAGEMENT SETUP

ACPI Aware O/S Yes S Available Options:

ACPI Standby State S1/POS

USB Device Wakeup From S3-S5 Disabled

Re-Call VGA BIOS at S3 Resuming Enabled

Power Management / APM Disabled

Video Power Down Mode Disabled

Hard Disk Power Down Mode Disabled

Standby Time Out (Minute) Disabled

Suspend Time Out (Minute) Disabled

Throttle Slow Clock R atio 50%~56.25%

Display Activity Ignore

IRQ3 Monitor

IRQ4 Monitor

IRQ5 Ignore

IRQ7 Monitor

IRQ9 Ignore

IRQ10 Ignore

IRQ11 Ignore

IRQ12 Ignore

IRQ13 Ignore

IRQ14 Monitor

IRQ15 Ignore

System Thermal Disabled

Thermal Active Temperature 65°C/149°F

Thermal Slow Clock Ratio 50%~56.25%

Power Button Function On/Off

Restore on AC / Power Loss Last State

Resume On Ring Disabled

Resume On LAN Disabled

Resume On PME# Disabled

Resume On KBC N/A

Wake-Up Key N/A

Wake-Up Password N/A

Resume On PS/2 Mouse N/A

Resume On RT C Alarm Disabled

RTC Alarm Date 15

RTC Alarm Hour 12

RTC Alarm Minute 30

RTC Alarm Second 30 T F2/F3: Color

` No

Yes

ESC: Exit PgUp/PgDn: Modify



: Sel

Page 44

4.8 PCI / Plug and Play Setup

This section describes configuring the PCI bus system. PCI, or Personal Computer Interconnect, is a system that allows I/O devices to operate at speeds nearing the speed the CPU itself uses when communicating with its own special components. This section covers some very technical items and it is strongly recomme nded that only experienced users should make any changes to the default settings.

AMIBIOS SETUP – PCI / PLUG AND PLAY SETUP

Plug and Play Aware O/S No Available Options: Clear NVRAM No ` No OnChip VGA Frame Buffer Size 8MB Yes PCI Latency Timer (PCI Clocks) 32 Primary Graphics Adapter PCI Boot Screen Select CRT TV Out Type U.S NTSC LCD Panel Type 1. 800 x 600 TFT PCI IDE BusMaster Enabled Off Board PCI IDE Card Auto Off Board PCI IDE Primary IRQ Disabled Off Board PCI IDE Secondary IRQ Disabled

DMA Channel 0 PnP DMA Channel 1 PnP DMA Channel 3 PnP DMA Channel 5 PnP DMA Channel 6 PnP DMA Channel 7 PnP IRQ3 PCI/PnP IRQ4 PCI/PnP IRQ5 PCI/PnP IRQ7 PCI/PnP IRQ9 PCI/PnP IRQ10 PCI/PnP IRQ11 PCI/PnP ESC: Exit IRQ14 PCI/PnP PgUp/PgDn: Modify IRQ15 PCI/PnP F2/F3: Color



: Sel

Page 45

4.9 Peripheral Setup

The IDE hard drive controllers can s upport up to two separate hard drives. These drives have a master/slave relationship that is determined by the cabling configuration used to attach them to the controller. Your system supports two IDE controllers--a primary and a secondary--so you can install up to four separate hard disks.

PIO means Programmed Input/Output. Rath er than having the BIOS issue a series of command s to affect the transfer to or from the disk drive, PIO allows the BIOS to tell the controller what it wants and then let the controller and the CPU perform the complete task by them. This is much simpler and more efficient (also faster).

AMIBIOS SETUP – PERIPHERAL SETUP

OnBoard FDC Enabled Available Options:

OnBoard Serial Port 1 3F8/COM1

OnBoard Serial Port 2 2F8/COM2 Disabled

Serial Port2 Mode Normal Enabled

IR Pins N/A Duplex Mode N/A Receiver Polarity N/A Transmitter Pdarity N/A

OnBoard Prarllel Port 378

Parallel Port Mode Normal EPP Version N/A

Parallel Port DMA Channel 3

Parallel Port IRQ 7

OnBoard Serial Port3 3E8/COM3

Serial Port3 IRQ 10

OnBoard Serial Port4 2E8/COM4

Serial Port4 IR Q 11 OnBoard IDE Both OnBoard AC’97 Audio Enabled OnBoard Legacy Audio Enabled

Sound Blaster Disabled

SB I/O Base Address Disabled SB IRQ Select 5FT SB DMA Select 1 ESC: Exi t

MPU-401 Disabled PgUp/PgDn: Modify

MPU-401 I/O Address 330h-333h F2/F3: Color

Auto



: Sel

Page 46

4.10 Hardware Monitor Setup

AMIBIOS SETUP – HARDWARE MONITOR SETUP

*** System Hardware Monitor *** Available Options:

Chassis Intrusion Disabled ` Disabled TSENS1 Temperature Enabled TSENS2 Temperature Reset TSENS3 Temperature CPU Fan Speed Chassis Fan Speed

Vcore + 2.500V ESC: Exit +5.000V PgUp/PgDn: Modify +12.000V F2/F3: Color



: Sel

Page 47

4.11 Auto-Detect Hard Disks

This option detects the parameters of an IDE hard disk drive, and automatically enters them into the Standard CMOS Setup screen.

Up to four IDE drives can be detected, with parameters for each appearing in sequence inside a box. To acce pt the displayed entries, press the “Y” key; to skip to the ne xt drive, press the “N” key. If you accept the values, the parameters will appear listed beside the drive letter on the screen.

AMIBIOS HIFLEX SETUP UTILITY – VERSION x.xx

Standard CMOS Setup

Advanced CMOS Setup

Advanced Chipset Setup

Power Management Setup

PCI / Plug and Play Setup

Peripheral Setup

Hardware Monitor Setup

Auto-Detect Hard Disks

Change User Password

Change Supervisor Password

Auto Configuration with Optimal Settings

Auto Configurat ion with Fail Safe Set t ings

Save Settings and Exit

Exit Without Saving

ESC: Exit : Sel F2/F3: Color F10: Save & Exit

Auto-detect all hard disk parameters

Page 48

4.12 Change Supervisor/User Password

AMIBIOS HIFLEX SETUP UTILITY – VERSION x.xx

Standard CMOS Setup

Advanced CMOS Setup

Advanced Chipset Setup

Power Management Setup

Enter new supervisor password: _

Change Supervisor Password

Auto Configuration with Optimal Settings

Auto Configurat ion with Fail Safe Set t ings

Save Settings and Exit

Exit Without Saving

ESC: Exit :Sel F2/F3: Color F10: Save & Exit

Change the Supervisor Password

You can set either supervisor or user pas sword, or both of th em. The differences are:



supervisor password:

menus.

 user password: just can only enter but d o not have the right to change the

options of the setup menus.

can enter and change the options of the setup

When you select this function, the following message will appear at the center of the screen to assist yo u in creating a password.

ENTER PASSWORD:

Type the password, up to eight characters in length, and press <Enter>. The password typed now will clear any previously entered password from CMOS memory. You will be asked to confirm the password. Type the password aga in and press <Enter>. You may also press <Esc> to abort the selection and not enter a password.

To disable a password, just press <Enter> when you are prompted to enter the password. A message will confirm the password will be disabled. Once the password is disabled, the system will boot and you can enter Setup freely.

Page 49

PASSWORD DISABLED.

When a password has been enabled, you will be prompted to enter it every time you try to enter Setup. This prevents an unauthorized person from changing any part of your system configuration.

Additionally, when a password is enabled, you can also require the BIOS to request a password every time your system is rebooted. This would prevent unauthorized use of your computer.

You determine when the password is required within the BIOS Features Setup Menu and its Security option (see Section 3). If the Security option is set to “System”, the password will be required both at boot and at entry to Setup. If set to “Setup”, prompting only occurs when trying to enter Setup.

4.13 Auto Configuration with Optimal Settings

When you press <Enter> on this item you will get a confirmation dialog box with a message shown below. This option allows you to load/restore the BIOS default values perm anently stored in the BIOS ROM. Pressing ‘Y’ loads the BIOS default values for the most stable.

AMIBIOS HIFLEX SETUP UTILITY – VERSION x.xx

Standard CMOS Setup

Advanced CMOS Setup

Advanced Chipset Setup

Power Management Setup

Load high performance settings (Y/N) ? N

Change Supervisor Password

Auto Configuration with Optimal Settings

Auto Configurat ion with Fail Safe Set t ings

Save Settings and Exit

Exit Without Saving

Load configuration settings giving highest performance

ESC:Exit :Sel F2/F3: Color F10: Save & Exit

Page 50

4.14 Auto Configuration with Fail Safe Settings

When you press <Enter> on this item you get a confirmation dialog box with a message similar to the figure below. This op tion allows you to load/restore the default values to your system configuration, optimizing and enabling all high performance features. Pressing ‘Y’ loads the default values that are factory settings for optimal performance system operations.

AMIBIOS HIFLEX SETUP UTILITY – VERSION x.xx

Standard CMOS Setup

Advanced CMOS Setup

Advanced Chipset Setup

Power Management Setup

Load failsafe settings (Y/N) ? N

Change Supervisor Password

Auto Configuration with Optimal Settings

Auto Configurat ion with Fail Safe Set t ings

Save Settings and Exit

Exit Without Saving

ESC:Exit :Sel F2/F3: Color F10: Save & Exit

Load failsafe configuration settings

Page 51

4.15 Save Settings and Exit

Pressing <Enter> on this item asks for confirmation:

AMIBIOS HIFLEX SETUP UTILITY – VERSION x.xx

Standard CMOS Setup

Advanced CMOS Setup

Advanced Chipset Setup

Power Management Setup

Save current settings and exit (Y/N) ? Y

Change Supervisor Password

Auto Configuration with Optimal Settings

Auto Configurat ion with Fail Safe Set t ings

Save Settings and Exit

Exit Without Saving

Write the current setting to CMOS and exit

ESC:Exit :Sel F2/F3: Color F10: Save & Exit

Pressing “Y” stores the selections made in the menus in CMOS – a special section of memory that stays on after you turn your system off. The next time you boot your computer, the BIOS configures your system according to the Setup selections stored in CMOS. After saving the values the system will be restarted again.

Page 52

4.16 Exit Without Saving

Pressing <Enter> on this item asks for confirmation:

Quit without saving (Y/N)? Y

This allows you to exit Setup without storing in CMOS any change. The previous selections remain in effect. This exits the Setup utility and restarts your computer.

AMIBIOS HIFLEX SETUP UTILITY – VERSION x.xx

Standard CMOS Setup

Advanced CMOS Setup

Advanced Chipset Setup

Power Management Setup

Quit without saving (Y/N) ? N

Change Supervisor Password

Auto Configuration with Optimal Settings

Auto Configurat ion with Fail Safe Set t ings

Save Settings and Exit

Exit Without Saving

Exit without saving the current setting

ESC:Exit :Sel F2/F3: Color F10: Save & Exit

Abandon all Data & Exit Setup

Page 53

Chapter 5

Software Utilities

This chapter contains the detailed information of IDE, VGA, LAN, audio and USB driver installation procedures.

5.1 IDE Driver Installation

The utility disk that came with the delivery package contains an auto-run program that invokes the installation programs for the IDE, VGA and Audio drivers. The following describes the installation procedures of each driver.

1. Insert Utility CD Disk to your CD ROM. The main menu will pop up

as shown below.

Page 54

2. Press “VIA 4 IN 1” and to go Setup.

3. Once the Welcome screen appears on the screen, make sure to

close any applicat ions running a nd then click on th e Next button.

Page 55

4. When the Readme window pops on the screen, you may read the

whole document including the license agreement or just press Yes to skip through and continue installation.

5. The 4 in 1 Setup dialog is now displayed. Select on Normally

Install and then click on Next.

Page 56

6. The next win dow lists all componen ts detected in your system

and asks you to select the on es re quiring drivers. Tick on all items then proceed by clicking on the Next button below the screen.

7. The program start s to install t he ATAPI driv er when you click th e

Next button on the screen below.

8. When the ATAPI driver is completely installed. The utility then

displays your DMA mode status and allows you to enable it. Tick on the box and press on the Next button to continue.

Page 57

9. The following screen then gi v e s you the choice of installi ng the

AGP driver in standard o turbo mode. Select on the Standard Mode and then click on Next to proceed.

10. Installation of the AGP driver is now complete. Once the screen

below appears, select on restarting your computer to activate all drivers/settings completed.

Page 58

5.2 VGA Driver Installation

5.2.1 VGA Driver Installation for WIN95/98/2K

1. With the Utility CD Disk stil l in yo u r C D R O M d r ive , op e n t he F ile Manager and then select the CD-ROM drive. As soon as the system reads the disk, the VGA Menu screen below will appear on your display. Click on VIA_8606 from the main menu.

Page 59

2. Select the operating system of your computer to proceed with the installation process.

Page 60

3. Once the Welcome screen appears on the screen, make sure to close applications that are running and then click the Next button.

4. When the display below appears on your screen, Setup is already ready to install and copy the related files onto your hard drive. Click on the Next button to proceed.

Page 61

5. After the installation finishes, you will b e prompted to restart your system. We recommend you to reboot your computer to allow the new settin gs to take effect. Click on the F inish button to reboot.

5.2.2 VGA Driver Installation for WIN NT4.0

1. Click the Start button on the lower left hand corner of your screen, then select Setting. Choose Control Panel and double-click on the Display icon to launch its Display

Properties window. Click on the Settings tab, and then choose Display Type. In the Change Display Type window, click on Have Disk.

Page 62

2. Specify the path of the new driver and then press on Enter. (If in driver D:, type d:\Vga/Via_8606/Nt40)

3. Select

S3 Graphics Twister

6. Click OK or press Enter.

Page 63

7. You will see warning panel about Third Party Drivers. Click on Yes to finish the installation.

8. Once the installation is completed, you must shut down the

system and restart for the new driver to take effect.

Page 64

5.3 LAN Driver Installation

5.3.1 LAN Driver Installation for WIN95/98/2K

1. With the Utility CD Disk still in your CD ROM drive, right click on My Computer icon from the Windows menu. Select on System Properties and then proceed to the Device Manager from the main menu.

2. Select on Other Devices from the list of devices then double-click on PCI Ethernet Controller.

Page 65

Page 66

3. The PCI Ethernet Controller Properties screen then appears, allowing you to re- ins tall the dr iver . Sele ct Dr iver fro m the main menu to proceed.

4. The window then displays the current status of your LAN driver. Press on Update Driver button to continue.

5. The program will then launch the Update Device Driver Wizard window that will install your device driver. Click on the Next button to proceed to the next step.

Page 67

6. When the succeeding window asks you what you wish Windows to do, tick on the “Search for a better driver….” Click on the Next button to proceed.

7. The Update Device Driver Wiza rd w ill th en a sk you to spec ify, b y ticking, the path of the new driver. Tick on the open boxes where you require the program to s earch for th e device driv er then click on the Browse button to manually specify the path.

Page 68

8. Press on the OK button as soon as you have located the path of your driver.

9. Once the program returns to the Add New Hardware Wizard screen, your spec ified location will appear. Press on the Next button to continue.

10. Once the program detects the device driver (*.inf) file from your specified location , it will automatically copy th e files into your hard drive.

Page 69

11. When copying of d river files finishes, the p rogram will then ask you to insert your Windows.

12. The program then copies the necessary files from your Windows installation disk to comple te th e driver setup process. Once the driver is comple tely installed, the following message appears on your display. Click on the Finish button to proceed.

13. Restart your computer to make the new system settings take effect. Click on the Yes button when the screen below appears and your LAN Driver for Win95 and Win98 are now completely installed.

Page 70

5.3.2 LAN Driver Installation for WIN NT4.0

1. With the Utility CD Disk stil l in yo u r C D R O M d r ive , r igh t c lic k o n Network Neighborhood icon from the Windows menu. Select on Properties.

2. The system automatically detects the absence of Windows NT Networking. Click on the Yes button to start ins t allation.

Page 71

3. Tick on the “Wired to Networ k” on ce the following screen appears. Click on the Next to proceed.

4. Click on the Start Search button for the program to locate the Network Adapter.

Page 72

5. Once setup finishes the search, it will list a number of adapters for you to choose from. Press on the Have Disk button to assign the driver path location.

6. Setup now asks you for the location of the driver. When you have entered the new driver path, press on the OK button to continue.

Page 73

7. When Setup finds the information it needs about the new driver, it will display the device it found on the following screen. Press on the OK button to accept and procee d.

8. Setup then returns to Network Setup Wizard screen and displays your new Network Adapter. Click on Next to continue.

Page 74

9. The Network Setup Wiz a rd then allows you to set the Network Protocols on your network. Select the appropriate protocol and then click on Next to continue.

10. Before Setup starts installing the components found and the settings you made, it will give you the option to proceed or go back for changes from the following screen. Click on the Next button once you are sure of your devices.

Page 75

11. Windows NT Setup will then need to copy files necessary to update the system information. Specify the path then press Continue.

12. Once it finishes copying the files, Setup will now allow you to choose the Duplex Mode of your LAN controller. Press on the Continue button after making your selection.

Page 76

13. When Setup asks if you wish to change the TCP/IP settings of your system, select the appropriately. The default choice is No.

14. Setup then starts the Networking installation and copie s the files.

Page 77

15. When Setup finishes copying, the TCP/IP properties of your system will then pop up on your screen like the one shown below. Make the necessary changes then click on OK to continue.

16. When the screen below appears, click on Next to continue.

Page 78

17. Setup then prompts you that it is ready to start the network. You may complete the installation thereafter. Click on Next to continue.

18. Assign the work group or domain setting of your computer. Click on Next to continue.

Page 79

19. Restart your computer once the screen below appears. Click on Finish to continue.

20. Click on the Yes button to restart your computer. The LAN driver installation for WIN NT4.0 is now complete.

Page 80

5.4 Audio Driver Installation

1. With the Utilit y C D Dis k still in your CD RO M d r ive, open the File Manager and then select the CD-ROM drive. As soon as the system reads the disk, the VGA Menu screen below will appear on your display. Click on VIA_AC97 from the main menu.

2. Once the Welcome screen appears on the screen, make sure to close applications that are running and then click the Next button.

Page 81

3. The Select Components dial og box is now displayed. Sele ct on Install driver and then click on Next.

4. The program will now require the Windows installation disk for proper hardware installation. Insert the CD and then click on Next.

Page 82

5. When the display below appears on your screen, Setup is already installing and cop ying the relate d files onto your hard drive. Click on the Next button to proceed.

6. After the audio driver installation finishes, select the Finish button to complete the install ati on process.

Page 83

5.5 USB2.0 Driver Installation

5.5.1 Win 95/98

1. When the dialog box below appears, make sure you close all other Windows a pplic ation s and the n clic k on th e N to proceed.

2. Tick on the “Install USB 2.0 Driver” once the following screen appears. Click on the N

ext to proceed.

ext > button

Page 84

3. Once the setup program finishes copying files into your syst em, it will prompt you to restart the computer. Tick on the “Yes, I

want to restart my computer now” followed by a click on the Close button to reboot. Only after your computer boots will the

new settings take effect.

5.5.2 Win 2000

1. With the Utilit y C D Dis k still in your CD RO M d r ive, right click on “My Computer” icon from the Windows menu. Select on System Properties and then proceed to the Device Manager from the main menu.

2. Select on Other Devices from the list of devices and then double-click on Universal Serial Bus (USB) Controller.

Page 85

3. The Universal Serial Bus (USB) Controller Properties screen then appears, allowing you to re-install the d river. Select Update Driver from the main menu to proceed.

4. When the dialog box below appears, make sure you close all other Windows a pplic ation s and the n clic k on th e N to proceed.

ext > button

Page 86

5. The Software License Agreement dialog box then appears on the screen. Choose Y

6. Tick on the Install USB2.0 Driver once the following screen appears. Click on N

es to proceed.

ext > to proceed.

Page 87

7. The Software License Agreement dialog box then appears on the screen. Choose Y

8. Once the InstallShiel d Wizard completes the operation and update of your USB2.0 driver, click on the Print to File and

inish button to complete the installation process.

es to proceed.

Page 88

5.5.3 Win XP

NOTE:

1. With the Utilit y C D Dis k still in your CD RO M d r ive, right click on

2. Click on the N

Please make sure you have already installed

Pack1

“My Computer” icon from the Windows menu. Select on System Properties and then proceed to the Device Manager from the main menu.

ext > to proceed.

Service

Page 89

3. Tick on the Install USB2.0 Driver once the following screen appears. Click on N

4. Click Y

5. Tick on the Install VIA USB filter driver once the following screen appears. Click on N

es to update the USB2.0 driver.

ext > to proceed.

Page 90

6. Once the InstallShiel d Wizard completes the operation and update of your USB2.0 driver, click on the F complete the installation process.

inish button to

5.6 COM5~COM8 Driver Installation

5.6.1 Win 2000

1. When the dialog box below appears, make sure you close all other Windows a pplic ation s and the n clic k on th e N to proceed.

ext > button

Page 91

2. Tick on the “Search for a suitable driver for my device (recommended)” once the following screen appears. Click on

ext to proceed.

the N

3. Once the program returns to the Add New Hardware Wizard screen, your specified location will appear. Press on the N button to continue

ext

Page 92

4. Choose sisusb2.inf and press on the Open button to accept and proceed.

5. Once the InstallShiel d Wizard completes the operation and update of your USB2.0 driver, click on the F complete the installation process.

inish button to

5.6.2 Win XP

Page 93

2. Select on Other Devices from the list of devices and then double-click on PCI Serial Port.

3. The Universal Serial Bus (USB) Controller Properties screen then appears, allowing you to C

ontinue Anyway.

Page 94

4. Once the InstallShiel d Wizard completes the operation and update of your Serial Port driver, click on the F complete the installation process.

inish button to

Page 95

This Page is intentionally left blank.