Please take the time to follow the instructions in this owner’s guide carefully. It will help you set up and operate your system properly
and enjoy all of its advanced features. Save your owner’s guide for future reference.
WARNING:
WARNING: The apparatus shall not be exposed to dripping or splashing, and objects filled with liquids, such as vases, shall not be
placed on the apparatus. As with any electronic product, use care not to spill liquids into any part of the multi-disc changer. Liquids
can cause a failure and/or a fire hazard.
WARNING: No naked flame sources, such as lighted candles, should be placed on the apparatus.
Class B emissions limits
This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.
To reduce the risk of fire or electric shock, do not expose the product to rain or moisture.
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of
uninsulated dangerous voltage within the system enclosure that may be of sufficient magnitude to constitute a risk of
electric shock.
The exclamation point within an equilateral triangle, as marked on the system, is intended to alert the user to the presence of important operating and maintenance instructions in this owner’s guide.
CAUTION:
To prevent electric shock, match the wide blade of the line cord plug to the wide slot of the AC (mains) receptacle. Insert fully.
CAUTION: DO NOT place the product on any heat-sensitive surface, such as the finished surface of fine furniture. Like all electrical
equipment, it generates some heat.
CAUTION: Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous
radiation exposure. The multi-disc player should not be adjusted or repaired by anyone except properly qualified service personnel.
Class 1 Laser Product
This CD changer is classified as a CLASS 1 LASER PRODUCT according to
EN 60825-1:1994 + A1+A2, IEC60825-1:1993+A1+A2.
CLASS 1 LASER PRODUCT
KLASSE 1 LASER PRODUKT
LUOKAN 1 LASER LAITE
KLASS 1 LASER APPARAT
Notes:
• The product label is located on the bottom of the product.
• Where the mains plug is used as the disconnect device, such disconnect device shall remain readily operable.
• The product must be used indoors. It is neither designed or tested for use outdoors, in recreation vehicles, or on boats.
• This product is intended to be used only with the Bose
®
Wave® music system.
The disc changer conforms to the EMC directive 89/336/EEC and to the Low Voltage Directive 73/23/EEC. The complete
Declaration of Conformity can be found on www.bose.com.
WARNING:
K
eep the remote control battery away from children. It may cause a fire or chemical burn if mishandled. Do not recharge, disassemble, heat above 100ºC (212ºF), or incinerate. Dispose of used batteries promptly. Replace only with a battery of the correct type and
model number.
WARNING: Danger of explosion if battery is incorrectly replaced. Replace only with Duracell, Eveready, Energizer, Maxell, Toshiba,
or Shun Wo CR2032 or DL2032 3-volt lithium battery.
Please dispose of used batteries properly,
following any local regulations. Do not incinerate.
1.Read these instructions – for all components
before using this product.
2.Keep these instructions – for future reference.
3.Heed all warnings – on the product and in the
owner’s guide.
4.Follow all instructions.
5.Do not use this apparatus near water or moisture – Do not use this product near a bathtub,
washbowl, kitchen sink, laundry tub, in a wet basement, near a swimming pool, or anywhere else that
water or moisture are present.
6.Clean only with a dry cloth – and as directed by
Bose Corporation. Unplug this product from the wall
outlet before cleaning.
7.Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions – To ensure reliable operation of the product and
to protect it from overheating, put the product in a
position and location that will not interfere with its
proper ventilation. For example, do not place the
product on a bed, sofa, or similar surface that may
block the ventilation openings. Do not put it in a builtin system, such as a bookcase or a cabinet that may
keep air from flowing through its ventilation openings.
8.Do not install near any heat sources, such as
radiators, heat registers, stoves or other apparatus (including amplifiers) that produce heat.
9.Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug
has two blades with one wider than the other. A
grounding-type plug has two blades and a third
grounding prong. The wider blade or third prong
are provided for your safety. If the provided plug
does not fit in your outlet, consult an electrician
for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or
pinched, particularly at plugs, convenience
receptacles, and the point where they exit from
the apparatus.
11. Only use attachments/accessories specified by
the manufacturer.
12. Use only with the cart, stand, tripod,
bracket or table specified by the
manufacturer or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus
combination to avoid injury from tip-over.
13. Unplug this apparatus during lightning storms
or when unused for long periods of time – to
prevent damage to this product.
14. Refer all servicing to qualified service person-
nel. Servicing is required when the apparatus
has been damaged in any way: such as powersupply cord or plug is damaged; liquid has been
spilled or objects have fallen into the apparatus;
the apparatus has been exposed to rain or moisture, does not operate normally, or has been
dropped – Do not attempt to service this product
yourself. Opening or removing covers may expose you
to dangerous voltages or other hazards. Please call
Bose to be referred to an authorized service center
near you.
15. To prevent risk of fire or electric shock, avoid
overloading wall outlets, extension cords, or
integral convenience receptacles.
16. Do not let objects or liquids enter the product –
as they may touch dangerous voltage points or shortout parts that could result in a fire or electric shock.
17. See product enclosure bottom for safety related
markings.
Information about products that generate
electrical noise
If applicable, this equipment has been tested and found to
comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed
to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions,
may cause harmful interference to radio communications.
However, this is no guarantee that interference will not
occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and
on, you are encouraged to try to correct the interference
by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and
receiver.
• Connect the equipment to an outlet on a different circuit
than the one to which the receiver is connected.
• Consult the dealer or an experienced radio/TV techni-
cian for help.
Note: Unauthorized modification of the receiver or radio
remote control could void the user’s authority to operate this
equipment.
This product complies with the Canadian ICES-003 Class
B specifications.
EnglishFrançaisEspañol
Important Safety Instructions
18. Use Proper Power Sources – Plug the product into
a proper power source, as described in the operating
instructions or as marked on the product.
19. Avoid Power Lines – Use extreme care when installing an outside antenna system to keep from touching
power lines or circuits, as contact with them may be
fatal. Do not install external antennas near overhead
power lines or other electric light or power circuits, nor
where an antenna can fall into such circuits or power
lines.
20. Ground All Outdoor Antennas – If an external
antenna or cable system is connected to this product,
be sure the antenna or cable system is grounded. This
will provide some protection against voltage surges
and built-up static charges.
Section 810 of the National Electrical Code ANSI/
NFPA No. 70 provides information with respect to
proper grounding of the mast and supporting struc-
FrançaisEspañolEnglish
ture, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of
antenna-discharge unit, connection to grounding electrodes, and requirements for the ground electrode.
Refer to the antenna grounding illustration on this
page.
Antenna grounding
Example of antenna grounding as per National Electrical
Code, ANSI/NFPA 70.
Antenna lead-in wire
Ground clamp
Electric service
equipment
Ground clamps
Power service grounding electrode
system (NEC ART 250, Part H)
Antenna discharge unit
(NEC Section 810-20)
Grounding conductors
(NEC Section 810-21)
Note to CATV system installer
This reminder is provided to call the CATV system
installer’s attention to Article 820-40 of the NEC (of USA)
that provides guidelines for proper grounding. In particular,
it specifies that the cable ground shall be connected to the
grounding system of the building, as close to the point of
cable entry as is practical.
Thank you for purchasing the Bose® Wave® music system Multi-CD Changer accessory.
Adding the Multi-CD Changer to your Wave
®
music system provides you with some valuable
benefits:
• A four-disc Wave
®
music system – Allows you to load and play up to four audio CDs.
Provides hours of uninterrupted CD music.
• Elegant integrated pedestal design – Using the same footprint as the Wave
®
music
system, the changer complements the elegance and simplicity of the system.
• One integrated remote control – Provides the simplicity of using one remote control
and one-touch selection of all built-in sources.
• Multiple source switching – By adding two input connections for external audio devices,
you can enjoy listening to one or two other audio sources in your home through the Wave
music system.
Carefully unpack your Wave® music system Multi-CD Changer and save all packing materials
for possible future use. The original packing materials provide the safest way to transport
your new Multi-CD Changer.
Make sure you received the parts shown in the following diagram. If any part appears damaged, do not attempt to use it. Notify Bose customer service immediately (see phone numbers on the inside back cover).
IMPORTANT
Your Wa v e® music system requires updating before it can operate the Multi-CD Changer.
Be sure to use the supplied update disc at the appropriate time during the setup process.
®
Wave® music system
update disc
Wave® music system Multi-CD Changer
Wave® music system
remote control
For your records
Now is a good time to record the serial number of your new Multi-CD Changer. The
serial number is located on the bottom of the product.
Serial number __________________________
Purchase date __________________________
We suggest you keep your sales receipt together with this owner’s guide.
4
Selecting a location for your system
Your Multi-CD Changer is designed to fit directly under your Wave® music system. Before you
connect the Multi-CD Changer to the Wave
complete system using the following guidelines.
• Place the system on a table or other flat surface.
• To enjoy maximum performance, place the system across the room from where you will be
listening.
• Place the system within two feet of a wall, and avoid placing it directly in a corner.
Setup
®
music system, select a good location for the
EnglishFrançaisEspañol
CAUTION:
DO NOT place your system on a heat-sensitive surface. Like all electrical equipment,
it generates some heat.
CAUTION:
DO NOT use your system in a damp location or any other place where moisture can
get inside.
Note:
DO NOT place your system on a metal surface. It could interfere with AM reception.
Seating your Wave® music system on the Multi-CD Changer
With the changer placed in your chosen location, carefully set your Wave® music system on
top of the changer.
• Make sure the rear feet of the Wave
changer.
• Make sure the Wave
®
music system sits flat and the side edges of both units are aligned.
®
music system fit into the recesses on top of the
5
Setup
Connecting the Multi-CD Changer to your Wave® music system
If you have already set up your Wave® music system, disconnect the power cord on the back
panel and set it aside. You will need to use it again during this setup procedure.
®
1.Plug the Bose
music system.
2.Plug the AC power cord from the changer into the AC power input connector on the back
of the Wave
3.Plug the Wave
back of the changer.
link cable from the changer into the Bose® link connector on your Wave
®
music system.
®
music system AC power cord into the AC power input connector on the
®
IMPORTANT
Make sure you perform
step 5. This enables
your Wave
FrançaisEspañolEnglish
system to operate the
disc changer.
®
music
4.Plug the other end of the power cord into an AC (mains) wall outlet. For best FM recep-
tion, straighten the power cord as much as possible. Your Wave
®
music system uses the
power cord as an FM antenna.
Turn to “Updating your Wave
5.
running the Wave
Wave
AC POWER
®
music
system
input
®
music system update disc.
®
music system” on page 7 and follow the instructions for
Bose® link
connector
Wave® music
system
4
Wave® music system
AC power cord
2
Changer
power
cord
3
Bose® link cable
1
Multi-CD
Changer
For best FM reception,
straighten the power
cord as much as
possible.
4
6
Updating your Wave® music system
To enable your Wave® music system to operate the Multi-CD Changer, run the update disc
included with the changer. The display will tell you when the update is finished.
1.Insert the update disc into the Wave
2.Wait approximately 20 seconds while your Wave
The display will show you a series of messages during this process:
Setup
®
music system CD slot (not into a changer CD slot).
®
music system performs the update.
EnglishFrançaisEspañol
LOADING
UPDATING FINISHED EJECTING
3.Wait for the system to automatically eject the update disc after updating is
finished. DO NOT eject the disc yourself.
After updating your system, refer to “Operation” on page 8 for operating information.
Wave® music system update disc
7
Operation
Remote control guide
Seek/Track
• Press: Skips to next/previous CD track
on the current disc.
• Press and hold: Rapidly skips to next/
FrançaisEspañolEnglish
previous CD track on the current disc.
Tune/MP3
• Press: Navigates between folders
when playing MP3 CDs.
• Press and hold: Rapidly scans forward/
backward through a CD track.
Play Mode
• Selects CD play modes (page 11).
An additional remote control is included with your Wave® music system Multi-CD Changer. This
remote is identical to the one used to control your Wave
®
music system. So, you can use either
remote to control the completed multi-CD system. Just aim the remote at the front panel and
press the buttons. The remote normally works within 20 feet of the front panel.
The following diagram describes the buttons used for playing CDs using the disc changer.
CD
• Press: Selects the CD source (page 10).
• Press again: Moves to the next disc
(page 10).
AUX
• Press to hear audio from an external
source connected to either the AUX 1 or
AUX 2 input on the changer (page 12).
• Press to switch between the AUX 1 and
AUX 2 input (page 12).
Stop/Eject
• Press once: Stops playing the current CD
(page 10).
• Press again: Ejects the stopped CD.
• Press and hold: Ejects a playing CD.
Play/Pause
• Press: Plays the current CD.
• Press again: Pauses a playing CD.
Note: Press-and-hold operations require holding the button down for at least one second.
Pressing FM/AM, CD, or AUX automatically turns on the Wave®music system to the
Note:
source selected.
Throughout this owner’s guide you will see button icons to the left of the operating instructions. These icons refer to buttons located on the remote control.
Turning your multi-CD system on and off
Press On/Off once to turn your multi-CD Wave®music system on or off. The system turns on
to the last source played. If the last source was CD, the last disc selected starts to play.
Press On/Off again to turn the system off.
OR
Press CD to turn the system on to the CD source. The last disc selected will play.
8
Loading CDs into the Wave® music system
Insert the disc, label side up, into the CD
slot below the display. The disc player will
automatically pull the disc in and begin
playing.
Press CD if the CD source is not selected.
Loading CDs into the Multi-CD Changer
1.Insert a disc, label side up, into an empty slot. An empty slot is indicated by an unlit disc
slot indicator.
2.With your fingers on the outside edge of the disc, push the disc all the way into the slot
Operation
EnglishFrançaisEspañol
.
Disc slot indicators
Off .......................... Empty disc slot.
Pulsating green ...... The disc slot contains a CD which is playing,
paused, or in a fast forward/backward scan.
Solid green............. The disc slot contains a CD, but it is not currently
playing.
Solid amber............ The CD is being ejected.
CAUTION:
• DO NOT INSERT mini CDs or non-circular CDs into the disc changer. These discs may not
play properly and could interfere with the system’s ability to eject them.
• DO NOT INSERT more than one disc at a time into any disc changer slot. Doing so can
cause damage to the disc and/or the disc changer.
9
Operation
Playing CDs
FrançaisEspañolEnglish
With the Multi-CD Changer installed, your Wave® music system operates as a four-disc
changer. Now, when you play CDs, all the normal CD information appears on the display with
one addition – the selected CD slot number (d1, d2, d3, or d4) appears above the elapsed
track time.
Clock time
Selected source
Play mode
Track number
Note: When switching from the FM, AM, or AUX source to the CD source, the CD in the most
recently used slot begins playing automatically. If that slot is empty, the next slot containing a CD
is selected.
The following information describes functions related to the Multi-CD Changer. Refer to your
Wave music system owner’s guide for complete instructions on playing the selected CD.
Number of selected CD slot:
d1 = Wave
d2, d3, d4 = changer
Elapsed track time
®
music system
Moving to another CD
Press CD to move to the next CD slot. The CD number on the display tells you which CD slot
is currently selected.
Stopping a CD
Press Stop/Eject once to stop a playing CD.
Ejecting a CD
Press CD on the remote to move to the CD you want to eject. Press Stop/Eject once to stop
a playing CD and then, press again to eject the CD.
Pressing Stop/Eject when the CD source is not selected ejects a disc from the most
Note:
recently used slot. If that slot is empty, the next CD found is ejected.
10
Operation
Play modes for audio CDs
Additional audio CD play modes are available on your Wave® music system after adding the
CD changer.
While playing a CD, press Play Mode repeatedly until the play mode you want is displayed:
• NORMAL PLAY ............Plays all tracks on the selected CD once in order.
• SHUFFLE .....................Plays all CDs once in random order. Plays tracks on each CD in
random order.
• SHUFFLE dISC ............ Plays all tracks on the selected CD once in random order.
• SHUFFLE RPT .............Repeats all tracks on all CDs in a random order that changes each
time the CD is repeated.
• SHUFFLE RPT dISC ....Repeats all tracks on the selected CD in a random order that
changes each time the CD is repeated.
• REPEAT ........................Continuously repeats all CDs in order.
• REPEAT dISC ...............Continuously repeats all tracks on the selected CD in order.
• REPEAT TRACK ...........Continuously repeats the selected track on the selected CD.
Play modes for MP3 CDs
While a music file CD is playing, you can change the way it is played. Press Play Mode
repeatedly until the play mode you want is displayed:
EnglishFrançaisEspañol
• NORMAL PLAY ............Plays all tracks on the selected CD once in order.
• SHUFFLE ......................Plays all CDs once in random order. Plays tracks on each CD in
random order.
• SHUFFLE dISC ............ Plays all tracks on the selected CD once in random order.
• SHUFFLE FOLDR ........Plays all tracks in the selected folder in random order.
• SHUFF RPT................... Repeats all tracks on all CDs in a random order that changes each
time the CD is repeated.
• SHUF RPT dISC ...........Repeats all tracks on the selected CD in a random order that
changes each time the disc is repeated.
• SHUF RPT FLDR ..........Repeats all tracks in a folder in a random order that changes each
time the folder is repeated.
• REPEAT ........................Continuously repeats all CDs in order.
• REPEAT dISC ...............Continuously repeats all tracks on the selected CD in order.
• REPEAT FOLDER ......... Continuously repeats all tracks in a folder in order.
• REPEAT TRACK ...........Continuously repeats the selected track on the selected CD.
11
Listening to an External Audio Source
Connecting an external audio source
The Wave® music system Multi-CD Changer provides two rear panel inputs (AUX 1 and AUX
2) for external audio devices such as TV, VCR, DVD player, cassette player, or MP3 player.
This gives you the advantage of hearing Wave
To connect a device, you will need a stereo RCA cable. Connect one end of the cable to the
audio output jacks of the source and the other end to one of the AUX inputs on the changer.
Be sure to match the red and white plugs on the cable to the red (R) and white (L) AUX jacks
on the changer.
Connection example: a TV connected to the Multi-CD Changer
FrançaisEspañolEnglish
®
music system sound from a range of sources.
Red
Use only a stereo connection. You will not hear the connected
device if just the left (L) or right (R) channel is connected.
Playing a connected audio source
To listen to a connected source:
1.Turn on the external device.
2.Press AUX on the Wave
between the AUX 1 and AUX 2 inputs. AUX 1 or AUX 2 appears on the display to confirm
your selection.
3.Adjust the volume using the Wave
The Wave® music system remote control cannot turn a connected AUX device on or off, or
Note:
change its settings or selections.
Note:
Neither AUX 1 or AUX 2 can be selected as an alarm source.
Red
®
music system remote control. Press AUX again to switch
®
music system remote control.
12
Cleaning
e
o
p
e
ra
tin
g
n
s
tru
c
tio
n
s
fo
r ty
p
e
s
o
f
b
a
tte
ry
to
b
e
u
s
e
d
Use only a soft dry cloth to clean your Wave® music multi-CD system. If necessary, you may
use a soft-bristled attachment to gently vacuum across the front. Do not use any liquid cleaning solutions, solvents, chemicals, alcohol, ammonia, or abrasives.
CAUTION:
Do not allow liquids to spill into any openings in the enclosure. If liquids get into the
unit, turn it off immediately. Call Bose
vice. See the list of phone numbers inside the back cover.
Replacing the remote control battery
WARNING: Keep the remote control battery away from children. It may cause a fire or chemical
burn if mishandled. Do not recharge, disassemble, heat above 212ºF (100ºC), or incinerate.
Dispose of a used battery promptly. Replace only with a battery of the correct type and model
number.
Care and Maintenance
®
Customer Support as soon as possible to arrange for ser-
EnglishFrançaisEspañol
CAUTION:
Danger of explosion if battery is incorrectly replaced. Replace only with Duracell,
Eveready, Energizer, Maxell, Toshiba, or Shun Wo CR2032 or DL2032, 3-volt lithium battery.
To replace the remote battery:
1. Place the remote face down on a flat surface.
2. Using your finger, push the tab lock to the side as shown and hold. Slide the battery
compartment open.
f
o
s
d
e
g
e
p
s
tin
ty
u
r
ra
e
e
fo
b
p
s
o
n
to
e
ry
e
tio
c
S
tte
a
tru
b
s
in
3. Remove the old battery and install the new one with the plus (+) symbol facing up.
f
o
d
g
pes
se
u
r ty
ratin
e
fo
b
pe
s
o
to
e
e
tion
c
S
attery
tru
b
s
in
4. Gently slide the battery compartment closed. It locks automatically.
13
Care and Maintenance
Troubleshooting
ProblemWhat to do
No system operation
• Check the power connections between the Wave
to “Connecting the Multi-CD Changer to your Wave
• Make sure you ran the update disc. Refer to “Updating your Wave
®
music system and the changer. Refer
®
music system” on page 6.
®
music system” on
page 7.
The system ejects the
update CD but does not
• Make sure you insert the update CD into the Wave
changer disc slot.
®
music system disc slot and not a
perform the update
No sound or
sound is muffled
• Make sure the Wave® Multi-CD Changer is plugged into a live power outlet and is turned on.
• Check the connections between the Wave® music system and the changer. Refer to “Connecting the Multi-CD Changer to your Wave
®
music system” on page 6.
CD skips• Make sure the system is not getting bumped in its current location. If so, move it to a more
protected location.
FrançaisEspañolEnglish
• Check the CD for smudges or dirt. If cleaning is necessary, wipe the CD straight out from
the center (NOT in a circular motion) to clean it.
CD does not play• Make sure there is a CD in the selected CD slot.
®
music system.
A CD is playing, but none
of the Multi-CD Changer
• Make sure CD is selected on the display of the Wave
• Check to see if the CD slot in the Wave
®
music system is selected, instead of a slot in the
Multi-CD Changer.
LEDs are lit
No sound heard from the
AUX device
Customer Support
• Make sure the RCA plugs on the stereo cable are pushed in as far as they can go.
• Press AUX on the remote and select the AUX input used by the device (AUX 1 or AUX 2).
• Make sure the AUX device is turned on.
For additional help in solving problems, contact Bose® Customer Support. Refer to the
address list on the inside back cover of this guide.
14
Limited warranty
Care and Maintenance
What is covered:
All parts defective in material or workmanship.
For how long:
One year from the purchase date.
What we will do:
We will, at our sole option, repair or replace any defective parts free of charge.
What you must do:
A. Call Bose
B. Properly pack the unit, if possible, in the original carton for shipping.
Other conditions:
This limited warranty is fully transferable for the one-year period following purchase.
THE PROVISIONS OF THIS LIMITED WARRANTY ARE IN LIEU OF ANY OTHER WARRANTY,
WHETHER EXPRESS OR IMPLIED, WRITTEN OR ORAL, INCLUDING ANY WARRANTY OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. BOSE CORPORATION’S
MAXIMUM LIABILITY SHALL NOT EXCEED THE ACTUAL PURCHASE PRICE PAID BY YOU
FOR THE PRODUCT. IN NO EVENT SHALL BOSE BE LIABLE FOR SPECIAL, INCIDENTAL,
CONSEQUENTIAL, OR INDIRECT DAMAGES.
®
Customer Service and ask for shipping instructions.
EnglishFrançaisEspañol
This limited warranty does not cover a defect that has resulted from improper or unreasonable use or maintenance, accident, improper packing, or unauthorized tampering, alteration,
or modification as determined solely by us. This limited warranty is void if the label bearing
the serial number has been removed or defaced.
Other Legal Rights:
This limited warranty gives you specific legal rights, and you may also have other rights which
vary from state to state or country to country. Some places do not allow limitations on implied
warranties or the exclusion or limitation of incidental or consequential damages, so the above
limitations or exclusions may not apply to you.
Technical information
Multi-CD Changer power rating
120V~ 50/60 Hz, 80W
Dimensions
2.6"H x 14.5"W x 9.9"D
(6.6 cm x 36.8 cm x 25.2 cm)