This indicates that serious injury or death may
result due to non-observance of this warning.
,CAUTION:
This indicates that minor or moderately severe
injury may result due to non-observance of this
warning.
WARNING: Before You Switch
the Appliance On
Please read the Operating and Installation Instructions
carefully, including the following. They contain
important safety information and instructions for
installation, use and maintenance for the appliance.
The manufacturer is not liable if you fail to comply with
the instructions and warnings. Retain all documents for
subsequent use or for the next owner.
Technical Safety
Improper installations and repairs may put the user at
considerable risk.
Repairs may be performed by an authorized service
provider.
Only use original parts supplied by the manufacturer.
The manufacturer guarantees that only these parts
satisfy the safety requirements.
If the Power Cord of this appliance is damaged, it must
be replaced by authorized service personnel or a
qualified person.
The appliance comes with a UL registered 3-wire Power
Cord.
An approved power cable extension may be purchased
from Customer Service only.
Never sever or remove the third (earth) conductor from
the Power Cord.
The appliance requires a 3-wire receptacle. The
receptacle must installed by a licensed electrician only.
Where there is a 2-wire standard wall receptacle, it is
the personal responsibility and duty of the customer to
have this receptacle replaced with a correctly earthed
3-wire wall receptacle. Do not use any adapter plugs.
Important Information When Using
the Appliance
■ Never use electrical appliances inside the appliance
(e.g. heater, electric ice maker, etc.). Risk of
explosion!
■ Never use a steam cleaner to defrost or clean
the appliance! The steam may penetrate electrical
parts and cause a short-circuit. Risk of electric
shock!
■ Do not use pointed or sharp-edged objects
to remove frost or layers of ice. You could damage
the refrigerant tubes. Leaking refrigerant may ignite
or cause eye injuries.
■ Do not store products that contain flammable
propellants (e.g. spray cans) or explosive
substances in the appliance. Risk of explosion!
■ Do not stand on or lean heavily against base of
appliance, drawers or doors, etc.
■ To clean the appliance, pull out the mains plug or
switch off the electrical breaker or fuse! Do not pull
out the mains plug by tugging the cable.
■ Bottles that contain a high percentage of alcohol
must be sealed and stored in an upright position.
■ Keep plastic parts and the door seal free of oil
and grease. Otherwise, parts and door seal will
become porous.
■ Never cover or block the Ventilation Openings for
the appliance.
■ People (children incl.) who have limited physical,
sensory or mental abilities or inadequate knowledge
must not use this appliance unless they are
supervised or given meticulous instructions.
■ Do not store bottled or canned drinks (especially
carbonated drinks) in the Freezer Compartment.
Bottles and cans may explode!
■ Never put frozen food straight from the Freezer
Compartment into your mouth.
Risk of low-temperature burns!
■ Avoid prolonged touching of frozen food, ice
or the evaporator pipes, etc.
Risk of low-temperature burns!
Children in the Household
■ Keep children away from packaging and its parts.
Danger of suffocation from folding cartons and cling
wrap!
■ Do not allow children to play with the appliance!
■ If the appliance features a lock:
Keep the key out of the reach of children!
4
RISK OF CHILD ENTRAPMENT
Child entrapment and suffocation are not problems of
the past. Junked or abandoned refrigeration products
are still dangerous...even if they will sit for “just a few
days”. Please follow these instructions when product
has reached the end of service to help prevent
accidents:
■ Remove the doors.
■ Leave the shelves in place so that children may not
easily climb inside.
General Regulations
The appliance is suitable for refrigerating food.
This appliance is intended for use in the home
and the home environment.
The refrigeration circuit has been tested for leaks
before leaving the factory.
State of California Proposition 65
Warnings
en-us
Installing the Appliance
Have a technician install and connect the appliance
according to the enclosed Installation Instructions.
,WARNING:
Do not install the appliance:
■ outdoors,
■ in an environment subject to drips of water,
■ in rooms with risk of frost.
Transporting
The appliances are heavy and must be secured during
transportation and installation.
Because of the weight/dimensions of the appliance
and to minimize the risk of injuries and damage
to the appliance at least two people are necessary
to set-up the appliance securely.
,WARNING:
This product contains chemicals known to the State of
California to cause cancer, birth defects or other
reproductive harm.
Information Concerning
Disposal
* Disposal of Packaging
The packaging protects your appliance from damage
during transit. All utilized materials are environmentally
safe and recyclable. Please help us by disposing the
packaging in an environmentally friendly manner.
Please ask your dealer or inquire at your local authority
about current means of disposal.
* Disposal of Your Old Appliance
Old appliances are not worthless trash! Valuable raw
materials can be reclaimed by recycling.
,WARNING:
1.
Pull out the Power Plug.
2.
Cut Off the Power Cord and discard with
the Power Plug.
3.
Do not take out the trays and shelves. This
helps to prevent children from climbing in!
4.
Do not allow children to play with
the appliance once it has spent its useful life.
Could cause suffocation!
Refrigerators contain refrigerant and gases in
the insulation. Refrigerant and gases must be disposed
of professionally. Ensure that tubing of the refrigerant
circuit is not damaged prior to proper disposal.
Installation Location
A dry, well-ventilated room is suitable as an installation
location. The installation location should not be
exposed to direct sunlight or placed near a heat
source, e.g. a cooker, radiator, etc. If installation next to
a heat source is unavoidable, use a suitable insulating
plate or observe the following minimum distances from
the heat source:
■ 1.2“ (3 cm) to electric or gas cookers.
■ 12“ (30 cm) to an oil or coal-fired cooker.
The floor of the installation location must not give way;
if required, reinforce floor. To ensure that the Ice Maker
functions correctly, the appliance must be upright.
Ventilation
The refrigeration unit is ventilated only via
the ventilation grille in the base. Never cover
the ventilation grille or place anything in front of it.
Otherwise the refrigeration unit must work harder,
increasing the power consumption.
5
en-us
Scope of Delivery
After unpacking all parts, check for any damage
in transit.
If you have any complaints, please contact the dealer
from whom you purchased the appliance or our
Customer Service department.
The following parts are included:
■ Built-in appliance
■ Interior fittings (depending on model)
■ Bag containing installation materials
■ Operating Instructions
■ Installation Instructions
■ Customer Service Booklet
■ Warranty enclosure
■ Information on the energy consumption and noises.
Connecting the Appliance
Have a technician install and connect the appliance
according to the enclosed Installation Instructions.
Do not remove the transportation protection devices
from the shelves and storage compartments until
the appliance has been installed.
Apart from statutory national regulations, you should
comply with all applicable local electricity companies
codes and requirements.
After installing the appliance, wait at least 1 hour before
switching the appliance On. During transportation
the oil in the compressor may have flowed into
the refrigeration system.
Before switching the appliance On for the first time,
clean the interior of the appliance (see chapter
“Cleaning the Appliance”).
Electrical Connection
,WARNING:
Avoid the risk of an electric shock!
,WARNING:
Insert into a grounded 3-wire receptacle. Never
remove grounding phase. Do not use any
adapters. Do not use any extension cords.
,WARNING:
Non-compliance with these instructions may
result in death, fire or an electric shock.
Improper connection of the protective conductor
may result in an electric shock. If you are in
doubt whether the appliance has been grounded
properly, have the appliance tested by
a qualified electrician or service technician.
The receptacle must be installed according to the
Installation Manual.
The appliance complies with protection class I.
Connect the appliance to 115 V/60 Hz AC through
a correctly installed 3-wire grounded receptacle.
The receptacle must be protected with a 10 to 16 A
fuse.
The appliance comes with a UL registered 3-wire
Power Cord.
Do not use extensions or distributors.
Please see the following table:
ApplianceMaximum Simultaneous Load
Refrigerator 30“2.0 amps
Check on the Rating Plate whether the indicated
voltage and current type correspond with the values of
your power supply. The location of the Rating Plate
can be found in the chapter “Customer Service”.
,WARNING:
Never connect the appliance to electronic
energy saving devices.
Our appliances can be used with power line and
sine-controlled inverters. Power line-controlled
inverters are used for photovoltaic systems
which are connected directly to the national grid.
Sine-controlled inverters must be used for
isolated applications (e.g. on ships or
in mountain lodges) which are not connected
directly to the national grid.
6
Getting to Know Your Appliance
These Operating Instructions refer to several models.
The diagrams may differ.
en-us
1Light Switch
2Controls
3Glass shelves
4Snack-Box
5Fruit and Vegetable Container
6Selection Buttons “Cool-fresh” Container
7“Cool-fresh” Container
8Ventilation
9Butter and Cheese Compartment
10Door Shelf
11Storage Compartments for large Bottles
7
en-us
Controls
APOWER Button
Serves to switch the whole appliance On and Off.
BALARM Button
Serves to switch the warning signal Off.
See chapter “Alarm function”.
CSUPER Button
Serves to switch the Super Cooling On and Off.
See chapter “Super Cooling”
DDisplay Panel
The temperature in the Refrigerator Compartment
is shown in the Display Panel. Activated special
functions are shown via “symbol”.
The menus and setting options which are available
are represented on the Display Panel in the Setup
Mode. See chapter “Special Functions”.
ESelection ButtonsB / C
The temperature setting is activated using
the Selection Buttons, see chapter “Setting
the Temperature”.
For selecting a menu in the Setup Mode,
see chapter “Special Functions”, section “Setup
Mode”.
FSetting Buttons @ / A
The temperature can be changed using
the Setting Buttons, see chapter “Setting
the Temperature”.
More settings can be selected in the Setup Mode,
see chapter “Special Functions”.
GSETUP Button
This button starts and ends the Setup Mode.
If the Setup Mode is ended using
the SETUP Button, the changes that have been
made are stored.
HVACATION Button
This button is used to switch Vacation Mode On
and Off, see chapter “Special Functions”, section
“Vacation Mode”.
Note:
A sound can be heard every time a button is pushed
if this function is selected in the “Sound” menu during
the Setup Mode.
Symbols in the Display Field
Super Cooling is active (see chapter “Super
Cooling”).
Vacation Mode is active (see chapter
“Special Functions”).
For the setting options in the Setup Mode
(see chapter “Special Functions”).
A warning message is displayed
(see chapter “Alarm function”).
8
en-us
Switching the Appliance On
Switch the appliance On with the POWER Button.
The appliance begins to cool. Light turns on when
the door is open.
,CAUTION:
Keep hands and fingers away from front and rear
openings of the refrigerator door when closing.
Risk of injury to hands or fingers!
Never allow children to climb on or play with
the refrigerator door.
Operating Tips
■ When the appliance has been switched on, it may
take several hours until the set temperature is
reached.
Setting the Language
The Display Languages can be changed according
to the table in the chapter “Special Functions”, section
“Setup Mode”.
To change the Display Language:
1.
Press the SETUP Button.
2.
Press the B or C Selection Button, until the set
language is displayed.
3.
Press the @ or A Setting Button, until the desired
language is displayed.
4.
Press the SETUP Button, in order to store
the settings.
The set temperature is displayed again on the
Display Panel.
Setting the Temperature Unit
The temperature can be displayed in degrees
Celsius (°C) or degrees Fahrenheit (°F).
1.
Press the SETUP Button.
The first menu (Temperature Unit) is displayed.
2.
Press the @ or A Setting Button in order to switch
between degrees Fahrenheit (°F) and degrees
Celsius (°C).
3.
Press the SETUP Button, in order to store
the settings.
The set temperature is displayed again on the
Display Panel.
Setting the Temperature
Refrigerator Compartment
(can be selected from +35 °F (2 °C) to +46 °F (8 °C))
We recommend a setting of +37 °F (3 °C).
Perishable food should not be stored above +37 °F
(3 °C).
1.
Press the B Selection Button.
2.
Set the temperature with the @ (warmer)
or A (cooler) Setting Button.
Special Functions
The following Special Functions can be selected
or displayed:
Setup Mode
In Setup Mode you can make your personal settings.
Switching On
Press the SETUP Button.
The first menu (temperature unit) is displayed on the
Display Panel.
Making Settings
1.
Switch on Setup Mode.
2.
Press the B or C Selection Button.
The next menu is displayed and its current setting
(mostly ON or OFF).
3.
Press the @ or A Setting Button.
4.
Press the B or C Selection Button to save and move
to the next menu.
9
en-us
Switching Off
Press the SETUP Button.
All of the changed settings are stored.
Note:
If no button is selected within 20 seconds, the Setup
Mode ends automatically. All of the changed settings
are stored. The set temperature is displayed again on
the Display Panel.
Menus in the Setup Mode
The following settings can be made.
MenuPossible setting
Temperature Unit°C (degrees Celsius)
°F (degrees Fahrenheit)
LanguageEnglish
French
Spanish
SoundOn
Off
Energy Saving Mode
(Eco Function)
On
Off
Vacation Mode
If leaving the appliance for a long period of time, you
can switch the appliance over to the energy-saving
Vacation Mode.
When Vacation Mode is switched On, the following
settings are made:
■ The appliance operates in Energy-Saving Mode.
■ The light is switched Off.
■ The “Super Cooling” function is ended (if activated).
Switching On
Press the VACATION Button.
The “VACATION” symbol is displayed on the Display
Panel.
Switching Off
Press the VACATION Button.
The previous settings and temperature values are
restored.
Rest Mode
When Rest Mode is switched On, the following settings
are switched Off:
■ Acoustic Signal
■ Interior Light
■ Messages in the Display Panel
■ The background illumination of the Display Panel is
reduced
■ Buttons are locked.
Switching On
1.
Press and hold down the SUPER Button.
2.
Press the VACATION Button.
3.
Press the SUPER Button and hold down for a further
3 seconds.
The “VACATION” symbol flashes on the Display
Panel and “RESTMODE” is displayed.
Switching Off
Press the VACATION Button.
The previous settings and temperature values are once
again activated.
Energy Saving Mode
If the Energy Saving Function (Eco Function) is
activated, the appliance switches to the Energy Saving
Operation. This Energy Saving Function is preset
at the factory in order to reduce energy consumption.
The background illumination of the Display Panel is
likewise reduced.
Switching On
1.
Press the SETUP Button.
2.
Press the C Selection Button, until “ECO MODE”
and the current setting (OFF) is displayed.
3.
Press the @ Setting Button, in order to reset
the setting.
4.
Press the SETUP Button, in order to store
the setting.
“ECO” is displayed on the Display Panel.
Switching Off
1.
Press the SETUP Button.
2.
Press the C Selection Button, until “ECO MODE”
and the current setting (ON) is displayed.
3.
Press the A Setting Button, in order to reset
the setting.
4.
Press the SETUP Button, in order to store
the setting.
10
en-us
Alarm Function
Door Alarm
The Door Alarm switches On if an appliance door is left
open for longer than three minutes. Close the door
to switch Off the Warning Signal.
Switching Off the Alarm
Press the ALARM button to switch Off the Warning
Signal.
Refrigerator Compartment
,WARNING:
Do not store explosive substances in
the appliance. Risk of explosion!
The Refrigerator Compartment is the ideal storage
location for ready meals, cakes and pastries, preserved
food, condensed milk, hard cheese, fruit and
vegetables sensitive to cold as well as tropical fruit.
When Purchasing Food, Please Note
The freshness at point of purchase is important for
the shelf-life of your food.
In principle, the fresher the produce when placed
in the “Cool-Fresh” Container, the longer it stays fresh.
Therefore, when buying food, always pay attention
to the degree of freshness.
Observe the expiration date specified by
the manufacturer for ready products and bottled
products.
Arranging Food in the Appliance
■ Wrap or cover food before placing in the appliance.
This will retain the aroma, color and freshness of
the food. In addition, flavors will not be transferred
between foods and the plastic parts will not become
discolored.
■ Allow warm food and drinks to cool down before
placing in the appliance.
■ Do not block air outlet openings with food in
the refrigerator compartment, otherwise the air
circulation will be impaired.
Food which is stored directly in front of the air outlet
openings may be frozen by the cold air flowing out.
■ Avoid contact of oil and fat with the plastic parts
and door seal.
Super Cooling
Super cooling cools the Refrigerator Compartment as
cold as possible for approx. 6 hours. Then
the appliance automatically switches to the temperature
set prior to super cooling mode.
Switch On Super Cooling, e.g.
■ Before placing large quantities of food in
the refrigerator compartment
■ For fast cooling drinks.
Switching On
Press the SUPER Button.
The display panel indicates the symbol “SUPER¾”.
Switching Off
Press the SUPER Button.
“Cool-Fresh” Container
The “Cool-Fresh” Container has a temperature of
almost 32 °F (0 °C). The “cool-fresh” drawer is
covered by a special filter which sets the ideal humid
climate.
The low temperature and the optimum moisture provide
ideal storage conditions for fresh food.
Food can be kept fresh up to three times longer than
in the normal cooling zone – for even longer freshness,
nutrient retention and flavor.
11
en-us
Selection Buttons for “Cool-Fresh”
Container
Press the appropriate button corresponding to the food
stored:
■ fish
For the storage of fish and seafood.
■ meat/poultry
For the storage of meat products, poultry, sausage
and prepared meals.
■ produce
For the storage of fruit, vegetables, mushrooms and
herbs.
The selection is displayed by illumination of
the corresponding button.
Interior Fittings
Removing the Shelves
You can reposition the Shelves inside the appliance
and Door Shelves as required.
Lift the Shelves and remove.
Shelves inside the Compartment
Door Shelves
Foods suitable for “Cool-Fresh” Container
In principle all foods which are fresh and are to remain
fresh for even longer, such as: fish, seafood, meat
and sausage, dairy products, and ready meals.
Foods not suitable for “Cool-Fresh”
Container
Fruit and vegetables sensitive to cold (e.g.: tropical fruit
such as pineapples, bananas, papaya, citrus fruits,
melons as well as tomatoes, aubergines, zucchini,
capsicums, cucumbers, potatoes).
The ideal storage location for these foods is
the refrigerator compartment.
Trays in the Refrigerator Compartment
1.
Lift tray slightly and take out.
2.
Lift tray at front slightly and insert into the runners.
3.
Lower tray and push back.
12
Removing the Humidity Filter in the “CoolFresh” Container
Take out the “Cool-Fresh” Container first. Then, pull out
the Humidity Filter.
Lift off the Filter Cover and take out the Filter.
en-us
Switching Off and
Disconnecting the Appliance
Switching the Appliance Off
1.
Press the POWER Button.
2.
Unplug the Power Plug.
Disconnecting the Appliance
If you do not use the appliance for a prolonged period:
1.
Take all food out of the appliance.
2.
Switch the appliance Off.
3.
Unplug the Power Plug or switch the fuse Off.
4.
Clean the appliance interior (see chapter “Cleaning
the Appliance”).
5.
Leave the appliance doors open to prevent odors
from forming.
Defrosting
Defrosting is actuated automatically.
Cleaning the Appliance
,WARNING:
Never clean the appliance with a steam cleaner!
,CAUTION:
■ Do not use abrasive, chloride or acidic
cleaning agents or solvents.
■ Do not use scouring or abrasive sponges.
The metallic surfaces could corrode.
■ Never clean Shelves and Containers in
the dishwasher. The parts may become
deformed!
Proceed as Follows
1.
Before cleaning: Switch the appliance Off.
2.
Unplug the Power Plug or switch the fuse Off.
3.
Take all food out and store in a cool location.
4.
Clean the appliance with a soft cloth, lukewarm
water and a little pH neutral cleaning liquid. Prevent
the rinsing water from running into the light.
5.
Wipe the Door Seal with clear water only and then
wipe dry thoroughly.
6.
After cleaning, reconnect and switch the appliance
back On.
7.
Put the food back in the appliance.
Interior Fittings
All variable parts of the appliance can be taken out for
cleaning (see chapter “Interior Fittings”).
13
en-us
Odors
If you experience unpleasant odors:
1.
Switch the appliance Off.
2.
Take all food out of the appliance.
3.
Clean the interior. See chapter “Cleaning
the Appliance”.
4.
Clean all packages.
5.
Seal strong smelling food in order to avoid odors
from forming.
6.
Switch the appliance On again.
7.
Store food in the appliance.
8.
Check whether the formation of odors is still
occurring after 24 hours.
9.
Exchange the odor filter. See chapter “Exchange
the odor filter”.
Exchange the Odor Filter
Spare filters are available from your dealer.
1.
Opening the filter holder.
Light (LED)
Your appliance features a maintenance-free LED light.
These lights may be repaired by Customer Service
or authorized technicians only.
Tips for Saving Energy
■ Install the appliance in a dry, well ventilated room!
The appliance should not be installed in direct
sunlight or near a heat source (e.g. radiator, cooker).
If required, use an insulating plate.
■ Do not block the Ventilation Openings
in the appliance.
■ Allow warm food and drinks to cool down before
placing in the appliance!
■ When thawing frozen products, place them
in the refrigerator. Use the coldness of the frozen
food to cool food.
■ Open the appliance as briefly as possible!
Operating Noises
2.
Remove the used Odor Filter and replace with a new
Odor Filter.
3.
Closing the filter holder.
Normal Noises
Droning
Motors are running (e.g. refrigeration units, fan).
Bubbling, humming or gurgling noises
Refrigerant is flowing through the tubing.
Clicking
Motor, switches or solenoid valves are switching On/
Off.
Preventing Noises
The appliance is not level
Please align the appliance with a spirit level. Use the
Height-Adjustable Feet or place packing underneath
them.
The appliance is not free-standing
Please move the appliance away from adjacent units or
appliances.
Containers or Shelves wobble or stick
Please check the removable parts and re-insert them
correctly, if required.
14
Bottles or containers are touching each other
Move the bottles or containers slightly away from each
other.
Before Calling for Service
Before you call Customer Service:
Please check whether you can troubleshoot yourself based on the following information.
Customer Service will charge you for advice – even if the appliance is still under guarantee!
Appliance
FaultPossible causeRemedial action
Appliance has no refrigeration
capacity.
The light does not work.
The display does not
illuminate.
The refrigeration unit is
switching On more frequently
and for longer.
The temperature in
the Refrigerator Compartment
is too cold.
The light (LED) does not work. The LED lamp is defective.Call Customer Service.
You experience unpleasant
odors.
Display indicates “E..”.Electronics have detected a fault.Call Customer Service.
Display indicates
“LOWPOWER”.
Display indicates
“HIGHVOLT”.
Appliance has been switched Off.Press the POWER Button.
Power failure.Check whether the power is on.
The fuse has been switched Off.Check the fuse.
The Power Plug has not been
inserted properly.
Appliance opened frequently.Do not open the appliance unnecessarily.
The Ventilation Openings have been
covered.
Large quantities of fresh food are
placed in the freezer.
Temperature has been set too low.Increase the temperature (see chapter
Light switch is jammed.Check whether it can be moved.
Strongly smelling food is not sealed.Clean the appliance. Seal strongly smelling
The mains voltage falls below
the permitted limiting value.
The line voltage exceeds
the permitted limiting value.
Check whether the Power Plug is secure.
Remove obstacles.
Switch Super Cooling On (see chapter
“Super Cooling”).
“Selecting the Temperature“).
food (see chapter “Odors”).
When the line voltage reaches the stipulated
value again, the warning message goes out.
If the warning message lasts for longer,
inform the energy supply company.
When the line voltage reaches the stipulated
value again, the warning message goes out.
If the warning message lasts for longer,
inform the energy supply company.
en-us
15
Loading...
+ 33 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.