Bosch WFVC5440UC/19, WFVC6450UC/19, WFVC544AUC/19, WFVC540SUC/19, WFVC5400UC/19 Owner’s Manual

...

Bosch Vision _ 300/500/DLX

Series

Clothes Washers

B_ H

_!_!_!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii_i

_iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii

_!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

_iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii

....._iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii

iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii

_iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii

!iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii ___________________________________________________________________________________________________________________________________________________________________

_iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii

Features and Benefits of Your New Washer

ActiveClean TMTechnology Bosch ActiveClean ® technology optimizes the wash pro-

cess at every stage of the cycle by sensing load size, water level and temperature needs for superior results. Digital sensors care for allfabrics including wool, mohair and silk. This machine virtually operates at the touch of a button.

EcoSmart TM Technology EcoSmart TMTechnology utilizes a network of sensors in the

Bosch Vision washer for cycles that conserve the most energy possible while maintaining superior washing performance. By adjusting to the size of the load and regulating temperature to never overheat, it is no wonder

that Bosch is the most efficient brand on the market.

EcoAction ® This option gives you the ability to reduce energy usage by

up to 20%. By selecting this option the temperature is reduced to save resources while the wash time is slightly extended to ensure proper washing.

ActiveWaterTM Wash System Only Bosch Vision washers featuring the ActiveWater TM

wash system can consume as little as 13 gallons of water but wash with the power of 400 gallons! By adding water faster and constantly raining water back down on the clothes, Bosch Vision gets the most out of every drop of

water.

Stain Removal This unique option begins each cycle with a cold water fill

and heats to all the most important water temperatures to remove stains. Since each type of stain is removed at a

different specific temperature, only Bosch Vision with the Stain Removal option can address the widest variety of

stains and remove them all in just one load.

Exclusive Hinge and Gasket System A reinforced hinge and our unique gasket design help seal

in the heat, allowing your laundry to reach the optimum temperature, which eliminates even the toughest stains.

3-Part Detergent Jet Dispenser A 3-part dispenser automatically distributes detergent,

bleach and softener at exactly the right times.

XxtraSamtary ® Cycle With this innovative cycle, a thermostat controlled

intelligent system heats up the water to 170° F. The clothes are thoroughly cleaned and sanitized while killing 99.99% of

most common household bacteria.

Baby CareTM Cycle The littlest people in the house usually account for the

toughest stains. This cycle heats the wash water up to 155° Fto remove even the most stubborn stains with ease.

Bosch Exclusive Paddles As your wash gently tumbles, the paddles cascade water

from high above, rinsing away suds and giving your laundry a complete, even clean. Our stainless steel drum optimizes

performance to ensure not a single shirt goes unturned.

Stainless Steel Drum The Vision TMwasher drum has hundreds of smooth double

punched holes, which allow your garments to gently tumble completely snag free.

Internal Water Heater An internal heating element heats the water to up to 180° F

while a digital temperature sensor continually monitors the water temperature. Bosch Vision TMwashers deliver the most efficient and accurate water heating method for each selected fabric type.

Quiet Performance Bosch washers use suspended brushless motors, isolated

pump systems and special sound-deadening material to keep them exceptionally quiet while in operation. This

means they can be installed virtually anywhere in the home without causing a disturbance. Bosch's special unbalance

control software eliminates noisy unbalance conditions.

AVS TM Anti-Vibration System The AVS TMAnti-Vibration System reduces vibration even

during high spins for near silent, smooth operation. So even ifthe Vision washer is installed on a second story you may

never know its there.

AquaStop TtM AquaStop TI_4 is an internal containment safety system

designed to protect against flood-type leakage to decrease the chance of water damage when the washer is turned on and operating.

AquaStop TM Hose The AquaStop TMHose stops water flow in the event the

AquaStop TMHose experiences flood-type leakage.

Table of Contents

Definitions .......................................................................................... 4

IMPORTANT SAFETY INSTRUCTIONS ................................................................. 4

Grounding Instructions .............................................................................. 6

INSTALLATION INSTRUCTION ........................................................................ 7

Introduction ....................................................................................... 7

Information concerning waste disposal ................................................................ 7

Intended use ...................................................................................... 7

Environmental Protection / Conservation Issues ......................................................... 7

Factory-supplied equipment ......................................................................... 7

Useful tools ....................................................................................... 8

Dimensions ....................................................................................... 8

Installation area .................................................................................... 8

Checklist for Installation ............................................................................. 11

Removing the transport bolts ......................................................................... 11

Water connection .................................................................................. 12

Electrical connection ............................................................................... 14

Leveling procedure ................................................................................. 15

Transporting the Washer ............................................................................ 16

OPERATING INSTRUCTION .......................................................................... 17

Panel ............................................................................................ 17

Before Using For the First Time ....................................................................... 18

Using For the First Time .............................................................................. 18

First washing cycle (without laundry) ................................................................... 18

Preparing the laundry ............................................................................... 18

Sorting the laundry ................................................................................. 19

Degrees of soiling .................................................................................. 19

Loading the laundry ................................................................................ 19

Laundry Detergents and Additives ..................................................................... 20

Adding the correct amount of detergent ................................................................ 20

Filling laundry detergent and/or additives ............................................................... 20

Decolorizing ....................................................................................... 21

Cycles and Options .................................................................................. 22

Modifiers ......................................................................................... 22

Option buttons (Stain removal, Allergy Rinse, ECO Action) ................................................ 22

Cycle Selection Table ............................................................................... 23

Acoustic Signal .................................................................................... 24

Special features (Auto Load adjust, AVSTMAnti-Vibration System) .......................................... 24

During Washing ..................................................................................... 26

Re-selecting a program ............................................................................. 26

Add a garment / Interrupting the program .............................................................. 26

Canceling the active program ........................................................................ 26

After Washing ....................................................................................... 26

User Maintenance Instructions ........................................................................ 27

Cleaning and Care ................................................................................. 27

Cleaning the appliance housing and control panel ....................................................... 27

Cleaning the drum ................................................................................. 27

Cleaning the detergent dispenser ..................................................................... 27

Cleaning water inlet strainers ......................................................................... 27

Descaling the washing machine ...................................................................... 28

Troubleshooting of Minor Faults ...................................................................... 29

Customer Service .................................................................................... 31

STATEMENT OF LIMITED PRODUCT WARRANTY ...................................................... 32

Cycle Selection Table ................................................................................ 104

Congratulations! Your washing machine is a modern,

high quality domestic appliance.

This modern washing machine cleans your laundry using the most

sophisticated washing processes to obtain superior cleaning results.

Excellent engineering and reliability reduce operating costs significantly.

An easy operation philosophy, a variety of customized washing cycles and a solid touch and feel make this

appliance a user-friendly assistant in your household.

Your washer offers the following standard features:

Low noise level for washing and spinning.

Large door with magnetic door lock.

Door opening 16 inches (41 cm), quality sturdy hinge, opening angle

is 160°. Drum capacity 22 Ibs (10 kg) for

regular cotton loads.

Each washing machine which leaves our factory has undergone a thorough performance test and is in full working condition. The appliance may contain residual water due to the testing procedures. If you have any questions concerning installation of the washing

machine, our customer service will be happy to advise you.

Further information and a selection of our products can be found on our web

site: www.boschappliances.com Please read and follow these operating

and installation instructions along with all other information enclosed with the

washing machine. These operating and installation

instructions describe various models. Differences are indicated in the

appropriate places. The illustrations may show different

details than your washer.

Definitions

WARNING - This indicates that death or serious injuries may

occur as a result of

non-observance of this warning.

CAUTION- This indicates that

minor or moderate injuries may

occur as a result of

non-observance of this warning.

NOTICE - This indicates that

damage to the appliance or

property may occur as a result of non-observance of this warning.

This symbol is used to draw the

user's attention to important matters.

/k IMPORTANT SAFETY INSTRUCTIONS

2. Do not wash articles that have been previously cleaned, washed,

The warnings and safety instructions in this manual can not

cover all possible risks, conditions and situations that may arise. Use

common sense and exercise caution when installing, maintaining

and operating this or any other appliance.

To reduce the risk of fire, electric shock, serious injury or death when using your washing machine, follow basic precautions, including the following:

1. BOSCH washers are provided with an Operating, Care and Installation

Instructions Manual. Read and understand all instructions before

using the washing machine.

soaked, or spotted with gasoline, dry cleaning solvents, other

flammable or explosive

substances as they give off vapors

that could ignite or explode.

3. Do not add gasoline, dry cleaning solvents, or other flammable or

explosive substances to the wash water. These substances give off

vapors that could ignite or explode.

4. Under certain conditions hydrogen gas may be produced in a hot water system that has not been

used for 2 weeks or more. HYDROGEN GAS IS EXPLOSIVE.

If the hot water system has not been used for this length of time,

turn on all hot water faucets and

let the water flow out of each

faucet for several minutes before

using the washing machine. This will release any accumulated hydrogen gas. As the gas is

flammable, do not smoke or use

an open flame while carrying out this procedure.

5. To reduce the risk of fire, clothes, cleaning rags, mop heads and the

like which have been soiled with

any flammable substance, such as vegetable oil, cooking oil,

petroleum based oils or distillates,

waxes, fats, etc., must be kept away from any source of ignition,

including a clothes dryer. These items may contain flammable

substances which, even after

washing, may smoke or catch fire.

6. Do not bypass any safety devices.

7. Store all laundry chemicals and

aids in a cool dry place according to the manufacturers' instructions.

8. To reduce the risk of fire or electrical shock, DO NOT use an

extension cord or an adapter to connect the washing machine to

the power supply.

9. Before the appliance is removed

from service or discarded, remove the door and the power cord/plug.

10. When children become old enough to operate the appliance,

it isthe responsibility of the parents or legal guardians to ensure that they are instructed in safe practices by qualified persons.

11. Do not allow children to play on or in the appliance at any time; severe injury or death could result. Children should be kept a safe distance away from appliances at all times. Children should only be

permitted within an appliance's vicinity if under close, constant adult supervision.

12. Do not allow children's toys or other items that might encourage children to climb on the washer, to

be stored on or in the washer or on shelves or in cabinets or other

storage areas above the washer.

13. Do not sit or stand on the top of the washing machine.

14. Do not allow anyone to climb, lean or hang on any part of the washer

including any protruding components such as the appliance door or a pullout shelf.

15. To reduce the risk of poisoning or chemical burns, keep all cleaning products out of the reach of

children.

16. Keep pets away from the washing machine.

17. Do not reach into the appliance if the wash drum is moving.

18. Do not install or store this appliance where it will be exposed

to the weather.

19. Do not tamper with the controls.

20. Do not repair or replace any part of the appliance or attempt any service unless specifically

recommended in the user maintenance instructions or in

published user repair instructions that you understand and have the skills to carry out.

21. Do not touch the washer door if washing at high temperatures.

22. Use caution when draining hot water.

23. Removing any panel can expose sharp edges and points, electrical

connections or hot surfaces.

24. Always unplug the washing machine from the power supply

before attempting any service.

Disconnect the power cord by grasping the plug, not the cord.

25. Do not machine wash fiberglass materials (such as curtains and window coverings that use

fiberglass materials). Small

particles may remain in the washing machine and stick to

fabrics in subsequent wash loads

causing skin irritation.

26. Do not insert/pull out the power plug with wet hands.

27. Do not use the washing machine if it has a worn power cord or loose plug. If this is the case, contact an authorized service agent.

28. Do not operate the washing machine if any guards, panels and/or fasteners except transport

fixing bolts have been removed.

29. The washing machine must only be used for its intended purpose.

30. Always follow the fabric care instructions recommended by the clothing manufacturer.

31. Make sure that all water connections to the washing

machine have shut-off valve(s)that are readily accessible. Close the washing machine water shut-off valve(s) at the end of each wash day.

32. Check the fill hose connections on a regular basis to ensure that they

are tight and not leaking, and before applying power to the

machine.

33. Always read and follow the instructions of the manufacturer of

the detergent(s), cleaning aid(s), fabric softener(s) and static

eliminator(s) which you are using. Heed all warnings and precautions.

34. Do not operate the washing machine if parts are missing

or broken.

35.

Do not operate this washing machine until you are sure that:

a. the washing machine has

been installed according to

the INSTALLATION

INSTRUCTIONS.

b. all water, drain, power and

grounding connections are in compliance with all local

regulations and/or other applicable regulations and requirements.

36. Failure to install, maintain and/or operate the washing machine

according to the manufacturer's

instructions may result in injury

and/or damage.

37. To avoid damage to the door, do not push against the door when moving the unit. Precautions should be taken to avoid damage

to the floor as well.

38. To avoid floor damage and mold growth, do not let spills or splashes cause standing water

around or under the appliance.

39. The water connections should be made and tested before electrical

power is applied to the machine.

SAVE THESE

INSTRUCTIONS

Notes:

The IMPORTANT

SAFEGUARDS and

WARNINGS indicated in this

manual do not cover all possible conditions which

may occur. Common sense, caution and care must be

exercised when installing, maintaining or operating the washing machine.

Always contact your dealer,

distributor, service agent or

the manufacturer about any

problems or conditions that you do not understand.

GROUNDING INSTRUCTIONS

This appliance must be grounded. In the event of damage or failure, grounding will reduce the risk of electric shock by providing a path of least

resistance for the electric current. This

appliance is equipped with a cord that

has an equipment-grounding

conductor and a grounding plug. The

plug must be plugged into an

appropriate outlet that is properly

installed and grounded in accordance

with all local codes and ordinances.

Improper connection of the equipment grounding conductor

can result in electric shock. Connect to an individual branch circuit.

Check with a qualified electrician or serviceman ifyou are in doubt as to whether the washer is properly grounded. DO NOT modify the plug provided with the appliance - if it will not fit the outlet have a proper outlet installed by a qualified electrician.

KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE.

In case of change of ownership, manual should be conveyed with the

washer.

INSTALLATION INSTRUCTIONS

Introduction

TO AVOID RISK OF INJURY The washing machine is heavy. Lift

with caution.

Be sure to observe all listed warnings

and cautions.

Frozen hoses can tear/burst. Do not install the washing machine outdoors

or in an area exposed to freezing conditions. Ifthe washing machine is

located in a room which will be

exposed to temperatures below freezing, or if it is located in a cabin that is being shut down for the

winter, any residual water in the

pump or water inlet hose(s) must be

drained.

These installation instructions are

intended for use by qualified installers. Inaddition to these instructions, if installing the washing machine:

In the United States comply with the National Electric Code, ANSI/NFPA70 -latest

edition/State and municipal and/or local regulations.

In Canada comply with the Canadian Electric Code C22.1 -

latest edition/Provincial and Municipal and/or local regulations.

Take care not to damage the washing

machine. Do not hold onto protruding parts (e.g. door) when lifting.

Inaddition to the safety information listed here, the local water and

electricity supplier may have special

requirements. If in doubt, have the appliance

connected by an authorized technician.

Information concerning

waste disposal

Disposing of the packaging

The shipping package has protected your new appliance on its way to your

home. All packaging materials are non-polluting and recyclable. Please

contribute to a better environment by disposing of packaging materials in an

environmentally friendly manner.

Please ask your dealer or local authority about the best means of disposal.

Keep children away from shipping carton and packaging components

to avoid risk of suffocation from

plastic wrap and folding cartons.

Disposing of your old appliance

Old appliances are not worthless rubbish! Valuable raw materials can be

reclaimed from environmentally friendly recycling.

If appliance is no longer usable, pull out the main plug, cut off the power cord and discard.

Also remove the washer door to

prevent children from locking

themselves in the appliance.

Intended Use

Your washing machine is intended:

For domestic use only. For cleaning machine washable

fabrics in tap water.

For operation using cold and hot (140 °F / 60 °C) tap water and

conventional additives that are suitable for use in residential washing machines.

Environmental Protection/Conservation Issues

Your washing machine uses water, energy and detergent efficiently,

thereby protecting the environment and reducing your household costs. To use your washing machine in an

efficient and non polluting manner:

Avoid using too much

detergent, Use detergents bearing the HE

symbol for high efficiency and front loading washers.

Add detergent according to the

degree of soiling, amount of laundry and water hardness, and

follow the detergent

manufacturer's instructions.

Factory-supplied Equipment

There is a packet of accessory parts

supplied with your washer. Check that all the accessory parts supplied for your model are there. If any parts are missing, contact your dealer immediately.

The drum contains:

Aquastop ®

user manual

literature pack

* found in select models only

1. Water supply hose for cold water (blue marking).

2. Water supply hose for hot water (red marking).

3. Water drain hose.

4. User manual literature pack (see below)

The literature pack contents include:

1. Elbow

2. Accessory parts bag

3. User manual

Theaccessorypartsbagcontains:

1.Coverstobeplacedovertheholes forthetransportbolts(after removingthetransportbolts duringwasherinstallation).

2.Wrenchforleveling.

3.Clampfordrainhose.

Onthebackofthewasher:

1.powercordwithplug

2.hotandcoldwaterconnections

3.4shippingbolts

Usefultools

Thefollowingtoolsarehelpful:

1.Flatheadscrewdriver.

2.Socketwrench13mm

3.Closedwrench13mm

DONOTpushagainstthewasher doorglass.Riskofbreakage!

Do not push against

the door glass!

Dimensions

a = 27.0 in. (68.7 cm) b = 29.7 in. (75.4 cm)

c = 36.8 in. (93.5 cm) (minimum)*

37.8 in. (96.2 cm) (maximum)*

d = 20.7 in. (52.5 cm) e = 49.8 in. (126.3 cm)

* height of appliance depends upon

extension of height adjustable feet. Minimum height is with feet turned all

the way in, against the bottom of the

washer. Maximum height is with feet extended as far as permitted (must leave thread of screw engaged enough for foot to be stable (1/4 inch /

6.4 mm) when extended). Door opening angle 160° Approx. weight = 220 Ibs (100 kg)

Installation area

Never ground the washer to plastic plumbing lines, gas lines or hot

water pipes.

This appliance must be installed on

a solid floor and well leveled due to

the higher spin speeds available. If

installing the machine on a wood floor over a basement or on a

second floor, the floor may need to be reinforced. Sound, vibration, and

risk of the washer "walking" will be influenced by the structure and

stability of the floor surface where

the appliance is installed.

Soft floor surfaces, such as carpets or surfaces with foam backing, are not suitable. If possible, place the washing

machine in a corner of the room.

If the washing machine is to be installed on a weak wood floor, consider the

following:

Screw a section of water resistant plywood (at least 3/4" thick) to the

floor. The plywood _hould be

sized to fit the footprint of the

washer, approximately 27" wide x

29.7" deep, or 54" wide x 29.7" deep to extend underneath both

the washer and the dryer for best

results and even height of the

appliances.

Secure the feet of the washing machine with holding brackets. Order the holding brackets (set)

from Bosch Customer Service

(WMZ 2200).

Accessories

Pedestal Mounting Kit

A storage pedestal with a pull-out drawer is available as an accessory for your washer. The pedestal adds 15

inches to the height of the washer.

Appliance must not be mounted on a pedestal in stacked

installations.

part no. WTZ 1610 isfor a solid white color pedestal. Other color pedestals may be

available.

Reference part no. WTZ 1610"X" in which the X designates an available color (eg: A for Anthracite, S for silver).

Please inquire at your dealer for color choices available.

You may also consult a current product catalog or visit our website at: www.boschappliances.com

If mounting the washer on the pedestal, follow the instructions supplied with the

pedestal. D If mounting the washer on a

pedestal, install the washer on the pedestal prior to removing the transport bolt assemblies from the rear of the washer (see page 11 for details).

Stacking Kits

There are two stacking kits available.

Basic Stacking Kit This kit anchors the dryer on top of the

washer and adds approximately 0.63

inches (16 mm) to the stacked height.

part no. WTZ 1601 is for the basic

mechanical stacking kit.

part no. WTZ 1600 isfor the solid white pull-out shelf stacking kit.

Other color pull-out shelf stacking kits may be available. Reference part no. WTZ 1600"X" in which the X designates an available color (eg: A for Anthracite, S for silver). Please inquire at your dealer for color

choices available.

Minimum Distances

Important information concerning minimum distances:

If the washer is to be installed with a dryer so that the fronts of the

appliances are to be flush with one another it is necessary to allow

additional rear clearance for the dryer venting system. Depending

on the location of the exhaust air connection, a minimum distance of 5 1Ainch (13.4 cm) must be

provided for ducts/brackets (see dryer installation instructions).

Benefits of maintaining greater distance (clearances) than the minimum shown include:

• reduction of the risk of mold formation behind the appliances.

• reduced noise transmission

• facilitation of installation and

service.

• more air cools the dryer, keeps

the dryer from overheating, and improves drying performance.

If the washer and dryer are to be installed in a small room, the doors

of the room must be fitted with vents of a specified minimum size.

Refer to the following illustrations of enclosed installations for

additional information.

Allow additional clearance for

door, wall and window molding where necessary.

Installation Types

Observe the following minimum clearances between the washer and

adjacent surfaces for all installation

types.

Minimum Installation Clearances

A Sides 0,25in,(6.4mm)

B Top 0,25in,(6.4mm) C Rear* 2,55in.(64.8mm)

D Front 0,50in,(12,8mm)

* as closeto wallasventingor water

connectionwill allow If installedwitha dryer,the largerrearclearancefor dryer

ventingis requiredforthe laundrypair

Units are designed so the dryer can be stacked on top of the

washer using one of the stacking

kits shown on page 9. Units are designed to allow for

under-counter installation, see required dimensions in under

counter installation section on page 10.

Height measurements shown in this section are with the washer feet at

minimum extension (turned in all the way up against the base of the washer).

Recessed or Closet Dimensions for installation in a closet or

recessed area are shown in the illustration below.

Pull-Out Shelf Stacking Kit

This kit serves to stack the dryer on top of the washer and also provides a pull- out shelf. This kit adds approximately

1.5 inches (38.5 mm) to the stacked

washer/dryer height. This kit may also be combined with the

pedestal accessory. The stacking kit will add approximately 1.52 inches and the pedestal will add approximately 15

inches to the height of the installed washer.

D The pedestal cannot be used for

washer/dryer stacked installations.

Closet Ventilation Requirements E Top 48sq,in.(310sq,cm) F Bottom 24sq,in, (155sq, cm)

Required Installation Space G Height 37.25in.(94.6cm)

H Width 27.50in,(69.9cm) I Depth 33.50in.(85.1cm)

Mounted on Pedestal

Dimensions for pedestal mounting

installation are shown in the illustration

below.

Stacked Washer and Dryer Dimensions for stacked installation are

shown in the illustration below. There are two stacking kits available for

stacking the dryer on top of the washer, see the "Accessories" section on page

Side by Side Dimensions for side by side recessed

or closet installation are shown in the illustration below.

G i i _/ i_i..~

Required Installation Space G Height 52.25in.132.7cm)

H Width 27.50in.(69.9cm)

I Depth 33.50in.(85.1cm) J PedestalHt. 15.0in.(38.1cm)

Appliance must not be mounted on a pedestal for under counter installations.

Pedestal With Pull-Out Shelf

Dimensions for pedestal and pull-out shelf installation are shown in the

illustration below.

(More than two people are

recommended to lift the dryer into position because of its weight and

size. Failure to do so could result in

persona njury or death.

Clearance dimensions A through D are found on page 9.

Closet Ventilation Requirements E Top 48sq.in.(310sq.cm)

F Bottom 24sq,in, (155sq,cm) Required Installation Space

G Height* 74.50in.(189,3cm)

*withbasicstackingkit

Height** 76.02in, (t93.1 cm)

**withpull-out shelfstackingkit H Width 27.50in,(69.9cm) I Depth 33.50in.(85.1cm)

Clearance dimensions A through D are found on page 9.

Closet Ventilation Requirements E Top 48sq.in.(310sq.cm) F Bottom 24sq,in, (155sq, cm)

Required Installation Space G Height 37.25in.(94.6cm) H Width 54,75in,(139,t cm)

I Depth 33.50in.(85.1cm)

Height Requirement if mounted on a pedestal 52.25in.(132.7cm)

Under Counter Dimensions for undercounter

installation are shown in the illustration below.

G A,

Required Installation Space

G Height 53.75in.(136.5cm)

H Width 27.50in.(69.9cm) I Depth 33.50in.(85.1cm)

J Pedestalht 15.0in.(38.1cm)

Appliance must not be mounted on a pedestal for under counter

installations.

Appliance must not be mounted on a pedestal for stacked

installations.

The washer must not be stacked on top of the dryer. Serious injury

and damage may result.

Utilize care in sliding the stacked

washer and dryer units into place.

See the stacking kit installation

instructions for further information.

Clearance dimensions A through D are found on page 9.

Required Installation Space G Height 37.25in.(94.6cm) H Width 27.50in.(69.9cm)

Width* 54.75in.(139.tcm) * washer and dryer side by side

I Depth 33.50in.(85.1cm)

Appliance must not be mounted

on a pedestal for under counter installations.

Checklist for Page

Installation

completely remove4 transport bolt 11 assembliesand movethe washer

into place

connectthewatersupplylinesand 12 drainpipe

connecttheelectricalpower 14 slidethe washerintoitsfinal location 15

levelthewasheras lowas possible 15

beforefirst use,runacleaningcycle 18

Removing the transport bolt assemblies

To avoid possible injury and damage to the appliance and adjacent surfaces, all four transport bolt

assemblies must be removed before using the appliance. Retain the bolt

assemblies for use in any future transport (e.g. when moving). Ifyou have purchased a pedestal mounting kit, follow the installation instructions provided with it before removing the transport bolt

assemblies.

The bolt assemblies may be easier to remove using 13 mm socket

wrench.

Pull the washer drum slightly

forward towards the open washer

door to reduce pressure on the

transport bolt assemblies.

Slide each loosened transport bolt

assembly out of its retaining slot,

then pull it out through the round

hole in the housing.Completely

remove all 4 transport bolt

assemblies (each assembly

consists of a bolt, a metal flat

washer and a white plastic

bushing).

If the bushings do not come out

when removing the bolt

assemblies, place the bolts back

into the bushings and carefully try

again. It is important to do this

with the bolts, otherwise the

bushings will not come out

properly.

To store the bolt assemblies for future use, do not remove the bolts

from the plastic bushings.

Storing the transport bolt assemblies

Always keep the transport bolt

assemblies for future transportation of

the appliance (such as when moving ).

Store the transport bolt assemblies

with the washer and bushing attached.

Do not remove the bolt and

washer from the bushing.

D If mounting the washer on a

pedestal, install washer on the pedestal prior to removing the transport bolt assemblies.

Loosen all four bolt assemblies before removing any of the bolts all

the way from the unit.

Remove the bottom two bolt assemblies prior to removing the

top two bolt assemblies. Remove all four bolt assemblies in the order

shown in the diagram below.

_ ,, _ ......

---7T7---- ......

) ....... .......

"\,

Loosen the bolt assemblies using the closed end of the 13mm

wrench provided, or a 13mm socket wrench. Loosen them until

they can be moved freely.

Position the plastic cover over the

hole the transportation bolt

assemblies occupied. Push the

tab in (A) and slide the cover towards the small slot (B).

Water connection

Water supply

The washing machine must only be operated with hot (max. 140 °F/ 60 °C)and cold tap water. Do not connect the appliance to the mixer tap of an unpressurized hot-water

boiler.

If in doubt, have the water connection installed by an authorized technician.

The water supply hoses must not be:

Kinked, bent or flattened in such a way as to potentially diminish

water flow. Modified or cut (integrity can

no longer be guaranteed). Periodic inspection and

replacement of damaged or kinked hoses is recommended.

Replacement of the water supply hoses after five years of use may help reduce the risk of hose failure.

If installing the washing machine in a new building or a building in which

the plumbing system was recently

installed or upgraded, flush the lines before installing the washing machine to remove any sand, dirt or

residue.

Supply Line Connection

C Cold water connection H Hot water connection

(max. 140 °F / 60 °C)

Do not remove the strainers

from the water supply hoses.

Plastic threads must only be tightened by hand. Connect the water supply hoses to the back of

the washer. Tighten only metal-to metal

couplings (eg: connecting the Aquastop _ hose to the faucet) an additional two thirds turn using

pliers. Do not use pliers to tighten

plastic thread fittings onto plastic

or metal threads.

Properly secured EXTERNAL hose connections are the sole

responsibility of the customer. The manufacturer assumes no

responsibility or liability for improperly installed EXTERNAL

hoses or other connections.

Observe the water pressure in the supply network:

The water pressure should be between 20 and 120 p.s.i. (1.38

and 8.27 bar) when the faucet is turned on and at least 2.2 U. S.

gallons (8 liters) of water should be discharged per minute.

A pressure regulator valve must be installed ifthe maximum water

pressure is exceeded.

To prevent water damage, the hot and cold water valves should be

accessible when the washing machine is in place and should always be turned off when the washing machine is not in use.

Check to be sure the rubber washer/strainer is in the

Aquastop TMhose prior to attaching the hose to the faucet. It is not

necessary to remove the washer to clean the strainer. To clean, rinse

under running water. If necessary, lightly wipe the wire mesh strainer

to help dislodge any accumulated

debris.

i iiii

Also check to be sure the rubber

washer is present in the end of the Aquastop TMhose that attaches to the appliance.

After connecting, turn on the water

completely and check that connection points are watertight.

Hose Extension

The Aquastop _ hose may not fit in the

space available at the wall faucet. A short extension hose (part no. 645787 ) is available without charge through customer service (see page 31).

Other hoses

Available from appliance dealers:

Extended supply hose (approx. 96.1 in./2.44 m).

The connection points are under full water pressure. Check seal with faucet fully open.

AquaStopTM

The AquaStop TM system is available in select models only. AquaStop TM

protects against flood-type water

leakage through the clothes washer. This is accomplished using a stop valve in the AquaStop TM hose and a floating switch in the washer base.

If a leak is detected, the system is designed to shut off the water flow,

minimizing leakage. AquaStop TM isan internal containment

technology, and does not protect against outside forces, such as home

plumbing problems, or damage caused to the machine's hose (such as

installation damage). The clothes washer must be level and turned "on"

for proper functionality.

The AquaStop TM feature is not active and will not operate if the cycle selector is in the "Off" position.

The washer must_e level for correct Aquastop _Joperation.

AquaStop TMHose The AquaStop TM hose is an external

containment technology that prevents

potential flooding if the hose leaks.

Ifthe AquaStop TMhose leaks, a red

mark is displayed and the water inlet is

blocked.

Water d rai nag e

Do not bend or pull the water drainage hose.

The drain pipe height should be no lower than 12 inches (30.5 cm) below the top of the washer and no higher than 5 feet (152.4 cm) from the top of

the washer.

Connecting the water drainage hose

Do not remove the screw from

the clamp assembly. Loosen the

screw only enough so that the clamp will slide freely onto the water drain hose.

Place the hose clamp over the end of the drain hose before attaching

the drain hose to the appliance.

In-Wall Installation

Attach the elbow to the end of the

hose and insert the end of the hose into the wall drain

approximately three and a half to four inches. Do not allow the hose

to extend more than four inches

into the drain pipe.

The hose and elbow should be

properly extended into the open drain pipe when seated as shown in the above picture. There should be a gap between the drain hose

and the drain pipe to prevent

pressure buildup. Use a strap or cable tie to hold

hose in place. This is to keep the hose from coming out of the drain pipe during pump out. The hose

can be tied to one of the water supply hoses, or other suitable

nearby points.

An AquastopT_ hose that has activated cannot be reset. Contact

Customer Service for a replacement hose (see page 31).

2. Attach the drain hose to the drain hose connection on the back of

the appliance; position the hose

clamp approximately 3/8 inch (9 mm) from the end of the hose.

3. Tighten the clamp with a screwdriver.

Electrical connection

GROUNDING INSTRUCTIONS This appliance must be grounded. In

the event of damage or failure, grounding will reduce the risk of

electrical shock by providing a path of

least resistance for the electric current.

This appliance features a cord with an equipment-grounding conductor and a grounding plug. The plug must be

plugged into an appropriate outlet which has been properly installed and grounded in accordance with all local

regulations and ordinances.

Improper connection of the equipment grounding conductor may result in electric shock. Have the appliance checked by a qualified electrician or service

technician if you are in doubt as to whether the washer has been

properly grounded.

Do not modify the plug provided with the appliance - if it will not fit in the

outlet, have a proper outlet installed by a qualified electrician.

To reduce the risk of fire or electrical

shock, DO NOT use an extension cord or an adapter to connect the

washing machine to the power supply.

Use of a Ground Fault Circuit Interrupter (GFCI) is recommended.

Do not insert/remove the power plug with wet or damp hands.

Touch the plug only when removing the plug from the socket.

The washing machine must only be connected to an individual branch

circuit via a socket which has been properly installed and grounded.

The household electrical voltage must correspond to the voltage specification on the washing machine (rating plate, see page 31).

Connection specifications as well as the required fuses/breakers are stipulated below:

Volts Hertz Amperes Watts

110 120 60 15 1350

(max.)

Make sure that:

the power plug fits into the socket. the wire size is sufficient (make

sure the circuit uses the proper gauge wiring for the appliance

requirements). the grounding system is properly

installed.

The power cord may be replaced by an electrician only.

Replacement power cords are available from Customer Service.

Leveling Procedure

Importance of Leveling the Washer

The high spin speeds realized by your

high performance washer make

leveling the washer during installation a critical issue to reduce noise and

vibration. The washer feet are height adjustable

and must be adjusted so the washer is

leveland each foot is seated firmly against the floor.

If these procedures are not followed, the washer may

experience severe vibration

resulting in significant washer

movement and excessive noise

levels. D Level the washer prior to stacking

the dryer on it in a stacked washer/dryer installation.

Important Actions During

Leveling

Prior to beginning the leveling procedure, move the washer into the final location where you will

use it.

Do not push the washer across the floor with the washer leveling feet extended. This can damage the

floor or the washer leveling feet.

Start with all four washer leveling feet turned all the way in so they are snug up against the bottom of

the washer.

When leveling, keep the base of the washer as low to the floor as

possible to reduce sound and vibration during use. Extend the

washer leveling feet only as much as is necessary to level the washer.

Hold the washer foot (bottom rubber portion) with a 36mm (1 1/2 in.) wrench or a pair of slip-joint pliers while tightening the Iocknut up against the bottom of the

washer. Do not allow the foot to turn. If the washer leveling foot is

allowed to turn when tightening the Iocknut, the height of the washer on that corner will change.

Leveling Procedure

1. With the washer in its final position, check to see if it is level. To do

this, use a bubble level if one is

available. An alternate method is

to place a large bowl nearly full of

water on the center of the top of

the washer. The water should be

about 1/2" (12.7 mm) from the top of the bowl. If the water is the

same distance from the top of the bowl all the way around, the washer is fairly level.

Press down on each corner of the washer. The washer should feel

firm when pressed down upon, there should be no "give" or

movement.

If a corner of the washer moves downward when pushed down

upon, it is necessary to extend the washer leveling foot under that

corner. The foot should touch the

floor firmly.

Use the 16 mm (5/8") wrench provided (1) to turn the Iocknut clockwise (2). Turn the Iocknut downward until it locks against the

base of the foot. Once the Iocknut is tight against the foot, the foot will

turn with it when the Iocknut is turned. This will allow you to

extend the washer leveling foot.

(figure above shows the washer leveling foot removed from the

washer for clarity).

Turn the foot clockwise to extend

it. Continue turning until the foot

feels snug against the floor. Try

pushing down on the corner of the

washer again. When the washer

corner does not move downward

when pushed, lock the foot in

place by tightening the Iocknut back up against the bottom of the

washer.

Turn the foot counterclockwise to

raise it. The foot can be turned

with a 36 mm (1 1/2 in.)wrench or a pair of slipjoint pliers. Do not attempt to raise the foot by turning

the lock nut counterclockwise.

Only turn the lock nut counterclockwise to lock it against

the washer bottom when the

leveling foot is correctly positioned.

Hold the lower rubber portion of the washer foot with a 36 mm

(1 1/2 in.) wrench, or pair of slip joint pliers, to keep it from turning.

Transporting the Washer

Before transporting the washing machine:

Turn off the water.

Disconnect the washing machine

from the power outlet.

Remove the supply and drainage hoses.

Install the transport bolt assemblies (see section below).

Preparing and inserting the

transport bolt assemblies

(figure above shows the washer leveling foot removed from the washer for clarity).

8. Use the 16 mm (5/8 in.) wrench to turn the Iocknut counterclockwise.

Turn the Iocknut until it locks in place against the bottom of the

washer. The Iocknut should be tight against the bottom of the

washer. Do not over tighten.

D Important: Do not allow the

washer leveling foot to turn when turning the Iocknut, or the height of the corner will be changed.

9. Repeat steps 2 through 7 for each washer leveling foot until the

washer is level and all four feet press firmly against the floor.

The washer should not rock or move when pressing down on

each corner. Ifit does move, repeat the process.

D Ifa washer foot must be raised

(shortened), it may be necessary to reduce the weight on the foot so that it can be turned freely.

10. Periodically recheck the leveling status of the washer. Make sure

that all four feet remain locked in place. Ifany rocking or movement

of the washer is observed, recheck the leveling and the position of the

washer leveling feet.

Remove all four transport bolt hole covers.

Prepare the transport bolt assemblies:

Loosen the screw in the sleeve until the end of the screw is level

with the end of the sleeve.

i ,,,_,___Ji_ii_!i!i_iiiiiiiiiiillilih_.....

\, _ N .............

Insert and tighten all transport bolt assemblies. Make sure that the tab

on the transportation bolt is inserted in the slot on the washing

machine back panel.

OPERATING INSTRUCTIONS

Before using

To reduce the risk of fire, electric shock, or injury to persons, read the

IMPORTANT SAFETY INSTRUCTIONS before operating

this appliance.

Panel

Cycleselector

Switchesthemachineonandoffand selectsthe program.Canbeturnedin

bothdirections.

Cycle Selector

Perm Press

Before using your washing machine, read and follow all installation and

operating instructions.

Displayfield

TheReadyin timeis

displayed,if a programis

selected,

TheStart time isdisplayed

(500/DLXSeries)ifthe delay startfunctionisadditionally selected(noton300 Series washers)

Buttonsfor additionaloptions (inadditiontothecycleif required)

Stain Removal:Additionalwashingtimewith additionaltemperaturecontrolsto better

removestains, Allergy Rinse:Additionalrinsingcycle.

ECOAction®:Thisoptionreducesthe amountof energyusedforthewashing

cycle.

Option

Buttons

Start/Pause

Button

Special Prog_.ms

DelayStart button (5OO/DLXSeries)

TheStart timecanbedelayedin one

hourincrementsupto a maximumof

19 hours(ifrequired), ThedisplayshowstheDelayStart time,

Stad

Max Spinw

Reduced SpinC

Get,tie Spin C

, No FinatSpin

Pause

V_s_On

i/ ....... :

Start/Pausebutton Startsorinterruptsthe washingcycle(programmustbe

selectedbeforepressingStart/Pause).

Spin Selection button Forchangingthespin

speed(if required),The indicatorlightofthe

selectedspinspeedislit red,

Start/PauseIndicatorlight flashesred: Settingscanbechanged,thewashcycle

canbestarted,the doorislockedfor reasonsof safety, childlockisactiveor programis in "Pause"mode,

lit red: Programisrunning."Pause"canbeactivated. off: Programisfinishedornoprogramhasbeenselected

orthedoorisopen.

Before Using For

the First Time

To reduce the risk of fire, electric shock, or injury to persons, read the

IMPORTANT SAFETY INSTRUCTIONS before operating

this appliance.

The washing machine must be installed and connected properly (refer to Page

7). Turn the Cycle Selector to any cycle to

turn the washer on and illuminate the display. Turn the Cycle Selector to

"Off" to turn the washer off.

Before using your washing machine, read and follow all installation and

operating instructions.

Using For the First

Time

First washing cycle (without laundry)

Your appliance was thoroughly tested

before leaving the factory. A small

amount of residual water may remain in the washer. To ensure a fresh wash

with your initial load of clothes, first run the washer a complete cycle, without any laundry in the drum.

1. Do not load any laundry.

2. Turn on the water faucet.

4. Pour 1-2 Tbsp. detergent into the main detergent compartment (1 in

the preceeding illustration).

Do not use special detergents for delicates or wool (this will cause

excessive sudsing).

5. Close the detergent dispenser drawer.

6. Make sure the washer door is closed.

7. Set the cycle selector to Regular/Cotton hot

8. The Start/Pause indicator light

flashes (red).

9. Press the Start/Pause button.

The individual cycle steps are

indicated in the display field.

When "Remove laundry" is displayed:

Open the door.

Turn the cycle selector to "Off".

Preparing the laundry

Loose debris (coins, paper clips, nails and other hard objects) can

damage items of clothing as well as

parts of the washing machine (e.g.

drum).

Empty all pockets. Brush off lint and dirt.

Close fasteners that could cause laundry to catch and become

entangled. These include zippers, button up duvets (quilt covers) and

any hooks such as on brassieres.

Remove curtain rings or tie them up in a net bag.

Remove pins, buttons, buckles

and other hard objects to avoid

scratching the washer interior. Remove non-washable trim and

ornaments.

Turn synthetic knitwear inside-out to avoid pilling (the formation of

tiny balls of fluff common to knitted

or woven fabrics).

Treat spots and stains.

To prevent loss or damage to laundry

and the machine, the following items can be washed only in a mesh laundry bag:

Baby socks (small items) Hosiery

Belts

Underwired bras (due to risk of the wire coming loose during washing and causing appliance damage).

3. Open the detergent dispenser drawer.

Sorting the laundry

According to color and degree of soiling

Items of clothing may become discolored. Never wash new

multi-colored items together with other items.

White items may become gray if washed with dark items. Always wash

white and colored items separately.

Degrees of soiling

Typical stains

Sauces, tea, coffee, red wine, fruit, vegetables.

Blood, egg, milk, starch (containing protein/carbohydrate).

Soot, soil, sand (pigments), red clay.

Removing stains

If possible, pretreat stains while they are still fresh.

First, dab soapy water onto the stain. Do not rub.

Subsequently, wash the items of clothing using the appropriate cycle.

Occasionally, several wash cycles may be required in order to remove persistent, dried-on stains.

Sorting laundry according to care label specifications

XXTRA Baby Care TM Hot SANITARY ® 155° F168° C 125o F! 52oc 1700 Ft 77° C

Loading the laundry

TO AVOID EXPLOSION HAZARD!

Items of clothing that have been

pretreated with solvent-based cleaning agents, e.g. stain remover and dry cleaning solvents, represent an explosion hazard once loaded

into the washing machine. Therefore, these items must first be

rinsed thoroughly by hand.

Loose debris in the washing

machine drum can damage the

laundry. Before loading the laundry, check that there is no debris in the

drum.

Open the door.

Lighter Soiling No recognizable dirt or staining.

Laundry may have some body odor.

Light summer clothing. T-shirts, shirts and blouses that

have been worn for up to one day. Bed linen and guest towels that

have been used for one day.

Normal Soiling

Visible dirt and/or some light

recognizable staining.

T-shirts, shirts and blouses that are very sweaty or have been worn

several times. Dish towels, hand towels and bed

linen that have been used for up to one week.

Sheer curtains (without smoke staining) that have not been

washed for up to 6 months.

Heavy Soiling Dirt and/or staining recognizable.

Kitchen hand towels that have been used for several days or

show visible signs of soiling. Cloth napkins.

Bibs. Children's outer clothing or

sportswear with grass and soil stains.

Work clothes such as used for outdoor work or yard work.

Warm

95oF/35°C

consult fabric care label for washing

instructions and temperature settings

Fabric Types

Machine Wash, Cottons _/ Machine Wash,

Permanent Press Machine Wash, Delicates

Hand Wash _/

Temperatures

Cold _/ Warm _/ Hot "_

Do not wash clothes in washing machine if the care label says "Do Not

Wash" or the DO NOT WASH symbol _d is on the care label.

Place items loosely into the drum. Mix up large and small items.

Items of varying size will distribute better during the spin cycle.

For best results, it is recommended to load the drum depending on the fabric

type_

Full Load Cotton and Linens

1/2Load Permanent Press, Synthetic Blends

and Knitwear

V_Load Wool, Delicates, Silk

Do not exceed the maximum load

for the selected cycle. Overloading will cause poor wash results and will increase wrinkling.

Load the drum at least half full for Cotton and Permanent Press

cycles. Small loads will tend to create an unbalance condition.

Close the door completely. The door should close easily. It should not be necessary to force the door

to close.

r]]

Do not trap any items of clothing between the door and rubber seal.

Laundry Detergents and

Additives

Adding the correct amount of detergent

TO AVOID RISK OF POISONING! Keep detergents and additives out

of the reach of children.

Add the liquid detergent and/or

additive. First check to be sure the liquid insert is present in the

detergent compartment (1). If using a powder detergent, see the note below on removing the liquid detergent insert.

Detergent Dispenser Compartments

Measure out the detergent (powder or liquid) according to:

The water hardness. This information can be obtained from

your local water authority. Soft water requires less detergent.

The amount of laundry. The degree of soiling. Information

on soiling can be found on Page

19.

The specifications of the detergent manufacturer. Measuring the correct amount of detergent

reduces the strain on the environment and ensures optimum washing results.

Too little detergent: The laundry is not cleaned properly and

will eventually become gray and stiff. Grayish brown spots may appear on the laundry. The heater may calcify.

Too much detergent:

Excessive suds reduce wash agitation producing poor washing and rinsing results and may prevent proper

spinning.

Filling laundry detergent

and/or additives

Open the detergent dispenser drawer.

Do not overfill the compartment to avoid early dispensing.

DO NOT operate the washer without the detergent drawer in

place and fully closed! If using a powder detergent, first

remove the liquid detergent insert

from compartment 1.

Store the liquid detergent insert for later use.

We recommend HE detergents because they are designed to

achieve optimum performance with your front-loading washer.

Not using HE detergent could cause problems such as

oversudsing, extended cycle periods, or a decrease in wash performance.

Look for the HE logo (pictured below) on the front of your

detergent product.

[] Detergent Compartment

Use to add detergent to the wash load.

Liquid detergent should only be used with the liquid detergent

insert in place.

Add only the correct measured amount of detergent to avoid

oversudsing. DO NOT overfill for liquid

detergent, stop at the fill level marked as "max" on the siphon

cap (see illustration above).

At the beginning of the wash cycle, the detergent is flushed from the

dispenser into the wash. If using powder detergent, first

remove the liquid detergent insert

[] Fabric Softener Compartment

Add the recommended amount of fabric softener.

DO NOT overfill stop at the fill level marked as "max" on the

siphon cap (see illustration above). Overfilling can cause the softener

to be dispensed early

DO NOT pour fabric softener direcly into the wash load.

The fabric softener will automatically be dispensed during the last rinse cycle.

Do not use fabric softener with outdoor fabrics (ie: rubberized or

waterproof materials).

[] Bleach Compartment

Add the correct measured amount of liquid chlorine bleach, or color safe bleach, to this compartment.

DO NOT overfill stop at the fill level marked as "max" on the

siphon cap (see illustration). Overfilling can cause the bleach to

be dispensed early, which could result in damage to the laundry

load. DO NOT pour undiluted liquid

chlorine bleach directly on the laundry to avoid fabric damage.

The bleach will be automatically dispensed at the proper time

during the wash cycle. Concentrated or thick fabric

softener, conditioner and powder-bleach must be diluted with a little water before being poured into the dispenser.

Bleach may cause discoloration of the washer's colored surfaces. It

is important to keep leach away from the colored surfaces of your washer. Usea moist paper towel to clean up any spilled bleach.

D Close the detergent dispenser

drawer before starting any cycle. Please make sure the drawer is fully closed.

Decolorizing

Dyes may contain sulphur or chlorine. These substances may cause parts of the washing machine to corrode. Do not dye items of laundry inthe washing machine.

Cycles and Options

Foroptimumwashingresults,yourwasheroffersseveralcyclegroupsand additionaloptions.

Automatic CyclesincludeRegular/CottonandPermanentPress,Program

selectionisbasedin partonthelaundryfabrictype, Cycletimes will vary dependingon cycle selected, temperatureand

pressureof incoming water, water hardness,sizeof load, type of fabrics and amount of detergent used.

Specialprogramsarecustomdesignedforspecialwashneedsorspecific

typesof fabric, Additional options maybeselectedbypressingoneofthepaneloption

buttons,

Maximum spin speeds of the cycles

Revolutionsper Typeof

minute laundry/Extracycle

1200 Regular/Cotton

800 PermanentPress 600 Delicates

400 Wool/Handwash

600 Comforter 900 QuickFull

900 QuickLight

800 Jeans 1200 ColdIntensive 1200 XxtraSanitary®

1200 BabyCareTM 1200 Drain& Spin

Option Buttons

Stain Removal The Stain Removal option is

recommended for use with heavily soiled clothes that require the removal of tough, ground-in, protein-based

stains. It is not recommended to use the Stain Removal option when laundering normal or lightly soiled

clothes.

Special Programs

£uto_',st::: Vci:_:,_

XXtra

Sanitary

Allergy Rinse When this button is pressed, an

additional rinsing cycle will be added to

the selected cycle. The second rinse

helps to remove stubborn allergy irritants.

ECO Action ®

This option reduces the amount of

energy consumed by up to 20%. This option is not available for cold cycles.

* 300 Series maximum spin speed is

1100 rpm.

Cycle Selection Table

Regular/Cotton

Forcottonorlinen, Type Soiling

Hot sturdy,hardwearingitemsmadeof cottonor linensuchas workclothes normallyand/orheavilysoiledcolorfastfabrics

Warm sturdy,hardwearingitemsmadeof cottonor linensuchas jeans,T shirts lightlyand/ornormallysoilednon colorfast

Cold or fade) lightlysoilednon colorfastfabric

and underwear

andsweatshirts fabric sturdy,hardwearingitemsmadeofcottonor linen(colorsthatmaybleed

Permanent press

Easy-care(drip-dry)laundry

Hot

Warm

Cold

QuickFull Veryshortcycledesignedto washafull loadof verylightlysoiledgarments,

QuickLight 20 minutequickcycledesignedfortwoto threeitemsmadeofmixedblends

Wool/Handwash beenspecificallydesignedto provideextremelygentletreatmentof fabrics,Silkor otheritemsmarkedwiththe "Hand

ColdIntensive

Delicates

Jeans Speciallydesignedforjeansandheavydenims,thisprogramreducesfadingandwrinkling,

, _; Thisprogramwasspecificallydesignedto eliminatemostcommonhouseholdbacterium,Usedfor heavilysoiledand/or

XxtraSanltary® stainedcolorfastfabricsthatneedtobesanitized,suchas,towels,underwear,socks,bedsheets,tableclothes,etc,

madeof syntheticandblendedfabric(e,g,, cotton/polyester), cotton,permanentpress,linen,syntheticor blendedfabricsandouter

garments non-colorfastcotton,permanentpress,linen,syntheticorblendedfabrics

andoutergarments,Clothessuchasblouses,shirts,overalls non-colorfastcotton,permanentpress,linen,syntheticorblendedfabrics

andoutergarments,Clothessuchasblouses,shirts,overalls

HandWashsettingsareintendedfor verydelicateeasycareitemsthatusuallyrequirehandwashing,Thesecycleshave Wash"symbol@ onthe carelabelcanbe safelywashedwiththis cycle,

Mostaggressivewashsettingsusingonlycoldwater, Thecycleis designedforcottonsandsturdymaterials,andwashesat a maximumtemperatureof 68oF(200C),

Delicatessettingsareintendedfor usewithdelicateeasycareitemsmadeofcotton,satin,syntheticor blendedfabricsand curtains,dresses,skirtsandblouses,

Soiling

normallysoiledcolorfastitems

lightlyand/ornormallysoileditems

Comforter Speciallydesignedprogramfor large/bulkyitems, Extrawateris usedto ensurecompletewettingandgentlerspinsto

BabyCareTM itemsmadeofcottonorlinensuchastowels,sheetsorwhitesportssocks,

Drum Sanitize Waterisheatedupto 175oFto kill bacteriaandcleanthedrum

Drain& Spin Wateris drainedfollowedbya highspeedspin

i_Do not wash new multicolored laundry

together with other laundry.

reducestretching, Regular/Cottonsettingsareintendedto be usedfor heavilysoiledand/orstainedcolorfastfabrics,Sturdy,hard wearing

Rinse&Spin- SelectDrain& Spin, addtheoption"AllergyRinse".A rinseisadded,wateris drainedfollowedby a high speedspin

Modifiers

Spin Selection

Preset cycle setting of max. spin speed

can be changed.

Press this button until the desired

setting lights up. D'No final spin ("---")The water is

drained from the machine after the final rinse. Recommended for

delicate laundry. Use this setting to avoid creasing if the clothing

cannot be taken out of the washing machine immediately

upon completion of the cycle.

Delay Start Before starting a program you can

modify by when the cycle should be

started.

1 press = +1 hour

Press Delay Start button. The display

shows the start time 0:00. The time can be delayed up to a

maximum of 19 hours (with 1 hour increments) by pressing the Delay

Start button repeatedly. The Start time begins running

immediately after pushing the

Start/Pause button. This is indicated

by the points between the digits

flashing. D Changes to the Start time are

possible at any time, press the Delay Start button until the new time appears.

D If the program is changed or ifthe

program is interrupted, the preselected Start time isalso interrupted. The Ready in time of

the program is displayed. The

Start time must be reselected.

Acoustic Signal

An acoustic signal indicates program statuses (e.g. start/end of program and operating faults.)

To activate the signal:

Select a program.

Press and hold any two Option Buttons (e.g. Stain Removal and

Allergy Rinse) until a long signal is

emitted.

To deactivate the signal:

Select a program. Press two of the Option Buttons

and hold until a short signal is emitted.

D Do not activate/deactivate the

acoustic signal during a cycle.

"Start/Pause" button light

The Start/Pause button light conveys the following information:

Indicator light flashing red: Program can be started.

Adding laundry is possible.

Indicator light is lit red. Program is running.

Adding laundry is not possible

because the door is locked for safety reasons.

Laundry may be added after pressing the Start/Pause button.

Special features

Auto Load adjust

"Auto Load adjust" adjusts the water and energy consumption for each cycle and determines the amount of laundry.

This process is built into your machine

and occurs automatically.

The result is a reduction in water and

energy consumption when washing small loads.

AVS TM Anti-Vibration System

Unbalanced load detection

The AVS TMautomatic unbalanced load

detection system determines whether or Plotthe load is correctly balanced for spinning. If the load is not evenly distributed, the spin will be restarted. If after a pre determined Plumber of attempts the load cannot be balanced

the spin will be aborted and the cycle

resumed.

Displayed Time

When a cycle has been selected, the

expected cycle time is displayed.

The following will affect the displayed time:

Load size Repeated spin attempts to evenly

distribute load

Additional rinse cycles if excessive foam occurs

Low water pressure Selection of additional options,

e.g. "Allergy Rinse"

Due to these and other characteristics of the controls, the actual cycle time will

vary.

You may notice that these effects

(more or less time) change the displayed time when they occur in

the cycle. If no options are

selected and these effects do not occur, the time indicated will be

the time that the cycle will finish.

Washing

Turn on the water faucets.

Turn the program selector to the desired program.

If necessary, change the spin speed with the Spin selection

button until the the desired spin speed indicator light is lit.

Load the washing machine and close the door.

The Start/Pause indicator light flashes (red).

If necessary, press the button(s) for additional option(s).

The indicator light of the selected button is lit (red).

D If an incorrect combination was

inadvertently selected, the indicator light of the selected

button is turned off.

3 presses: +3 hour

If necessary, change the Start

time. Press the Delay Start button

until the desired Start time is displayed.

Press the Start/Pause button.

The indicator light is lit (red).

Display shows the run time of the selected program. The program

starts.

D Each program step is indicated by

the indicator lights under the

display.

During Washing

The washer drum system may experience a slight shudder or

shake as the drum accelerates to higher spin speeds due to

normal laundry imbalance.

Re-selecting a cycle

Turn the cycle selector to Off. Turn the cycle selector to a newly

selected cycle.

s_ Program

The Start/Pause indicator light flashes.

If required, change the settings. (see Page NO TAG).

Press the Start/Pause button. The cycle starts.

Add a garment /

Interrupting the cycle

You can put laundry in the drum after washing begins, take laundry out of the drum early or interrupt the cycle at any

time. D It is not recommended to add

laundry after the washing phase is complete.

D You can add or reduce laundry as

long as the Start/Pause indicator light flashes and it is safe to do so. Press the Start/Pause button.

The following displays are indicated in succession:

"Pause", "Door can be opened".

Open the door. Add/remove the laundry. Close the door. Press the Start/Pause button.

The cycle continues. The indicator light is lit.

When the Start/Pause indicator

light is illuminated, the cycle can be interrupted, however in some

cases the door will not be unlocked for safety reasons (high

water level, water temperature or drum speed).

If the speed is too high, the Start/Pause indicator light is

illuminated. Laundry can be added in "Pause" mode when the drum is

at a standstill.

Canceling the active cycle

If you would like to terminate a cycle and remove the laundry:

Press the Start/Pause button If Child Lock is active, it is

necessary to press and hold down

the Start/Pause button for five

seconds If the load is too wet, turn the cycle

selector to Drain/Spin and run the cycle using a spin speed appropriate for the laundry type (see pg. 22 for suggested spin speeds).

If a cycle is interrupted at a high

temperature, the door will remain

locked until the temperature in the drum has cooled down.

If the cycle is terminated by switching the appliance to "Off ",

the door will may remain locked

until the appliance is switched back on. Turn the cycle selector

to any other cycle. The door will

unlock after approximately 5 seconds.

After Washing

The Start/Pause indicator light turns

off. Display field: "Remove laundry".

Open the door.

Turn the cycle selector to Off.

Close the faucets. Remove the laundry.

To avoid the risk of rust, check for foreign objects (e.g. coins, paper clips) between the drum and rubber

door seal.

DAfter washing, leave the washer

loading door open for 24 hours to

allow the inside of the washing

machine to dry.

User Maintenance Instructions

Cleaning and Care

To reduce the risk of fire, electric shock, or injury to persons, read the

IMPORTANT SAFETY INSTRUCTIONS before operating

this appliance.

TO AVOID RISK OF ELECTRIC SHOCK!

Always disconnect the appliance from the power outlet before

cleaning. Never clean the washing machine

with a pressure washer.

TO AVOID RISK OF EXPLOSION! Never use flammable solvents to

clean the appliance.

Cleaning the appliance

housing and control panel

As required:

Use hot, soapy water or a mild, non-abrasive cleaning agent.

Dry with a soft towel.

Cleaning the drum

If rust spots have formed due to left-over debris (e.g. coins, paper clips, nails):

Use a chlorine-free cleaning agent. Follow the manufacturer's

instructions. Never use steel wool.

Cleaning the detergent dispenser

If residual detergents or additives have accumulated or if softener/bleach are

not fully rinsed out:

Pull open the detergent dispenser drawer. Press down (A)to release

the drawer catch. Remove the

drawer from the appliance.

Remove the liquid detergent insert by pulling it upwards from the detergent drawer.

Reinsert the liquid detergent insert if using liquid detergent. Slide the detergent dispenser drawer back into place and close it completely.

D DO NOT operate the washer

without the detergent drawer in

place and fully closed!

Cleaning water inlet strainers

This is necessary if very little or no

water flows into the washing machine. Cleaning is recommended every 6

months to reduce valve blockage in areas using hard water.

First release the water pressure in the supply hoses:

Turn off the water faucets. Turn the cycle selector to any

warm cycle.

Press Start/Pause button and

wait for 30 seconds. Turn the cycle selector to Off.

Cleaning the Door Gasket

After washing, wipe the gasket to

remove residual water or detergent. Mold or odor issues can result ifwater

or detergent isallowed to remain on the gasket.

Allow the drum to air out after washing by leaving the door

partially open. This will allow air to circulate and help dry out any remaining moisture in the drum or on the gasket.

Clean the detergent dispenser by inserting it under warm running water. Lightly wipe away any remaining detergent residue.

Cleaning the strainers at the water faucet

On both the hot and cold water faucet:

Cleaning Tips It is recommended that a small amount

of household bleach be run through the washer every 3 months.

With no laundry in the machine, run the machine as follows:

Disconnect the hose from the water faucet.

Rinse the strainer under running water.

Reconnect the hose.

Cleaning the strainers on the washing machine

Disconnect the hose from the back of the washing machine.

Pour 1/2 cup of bleach in the detergent compartment (1) of the dispenser

Run a Regular/Cotton Hot cycle

Descaling the washing machine

Descaling agents contain acids which may attack parts of the

washing machine and discolor the laundry.

Provided that you use the correct type of detergent, it is not necessary to descale the washing machine.

If white spots, lime or mineral deposits appear on the interior of the washing machine drum you can use a descaling

agent to remove them. However, ifthe appliance has to

be descaled, please follow the instructions provided by the descaling

agent manufacturer.

Pull out the strainer and rinse under running water.

Insert the strainer and reconnect the hose.

Turn on the water faucets and check that there are no leaks.

If water is leaking, check that the strainer is properly attached.

Turn off the water faucets.

Troubleshootin

of Minor Faults

TO AVOID RISK OF ELECTRIC SHOCK!

Repairs should only be carried out by an authorized technician.

If repairs are necessary, and you cannot eliminate the fault yourself with

the aid of the table below, follow these steps:

1. Turn the cycle selector to Off.

2. Disconnect the washing machine from the power outlet.

3. Turn off the water faucets.

4. Call Customer Service

(referto Page 31).

Troubleshooting items listed below may

not be covered by warranty service! Please carefully rule out any of these

issues before calling for service.

Fault Possible cause Action

Cycledurationextended. Thisis not afault. Addamoreappropriateamountof detergent.

Thesudsdetectionfeaturehasactivatedanadditional

rinsingcycleto reducetheamountof suds.

opened.

Doorcannotbeopened, eventhoughtheappliance

hasbeenswitchedoffand on again.

Controllightsdo notlight

up,

Cycledoesnotstart. Start/Pauseindicatorlight

flashes, Cycledoesnotstart,

Indicatorlight"Finished"is lit anddisplayisflashing

"E:01" Cycledoesnotstart,"Real

Timedelay"isindicatedin thedisplayfield,

Spinspeedcannotbe selected,

Detergentresidueinthe detergentdispenser,

Thisisnotafault. Theunbalancecompensationsystemis attemptingto

balancethe loadthroughrepeatedspins.

Thisis notafault. Thelaundryloadmaybelarge,requiringmoretime.

Powerfailure.Thedoorcannotbe

Cycleisrunningand/orthedoorislockedfor safety reasons.

Plugis looseor notinserted. CycleselectorturnedtoOff beforeendof cycle. Forsafetyreasonsthedoorhas beenlockedbecausethe

waterlevel,temperatureor highdrumspeed.

A fusehasblown.

Powerfailure.

Start/Pausebuttonnotpressed.

Doornotclosedproperly. Checkwhetherlaundryistrappedin door.

Endtimeselectedandactivated. None. Appliancestartsautomatically.

Spinningisalreadyinprogress;duringspincyclethe Selectspeedbeforespinning. speedcannotbechanged.

Detergentwasdampor lumpy. Cleananddrythedetergentdispenser(seePage27).

Alwaysloadthe drumwith largeandsmallitems together.

Allowadditionalwashingtimefor largerloads.

An interruptedcyclewill beresumedwhenpoweris restored.If the laundryis to be removedduringa power failure,call CustomerService(referto Page31).

Waituntilthecycleends (seePage26). Eliminatethecause,

Selectacycle, See"Addingtothe laundry/Interruptingthecycle",Page

26,

Resetcircuitbreaker. CallCustomerServiceif thisfaultrecurs. An interruptedcyclewill beresumedwhenpoweris

restored.If the laundryis to beremovedduringa power failure,call CustomerService(seepage31).

PresstheStart/Pausebutton.

Closethedoor(aclickshouldbe heard). cyclecontinues.

Usethe capofthedetergentbottleto measureliquid detergents.

Fault Possible cause Action

Waterdoesnotenterthe machineordetergentisnot

washedaway. Indicatorlight"spin"is lit anddisplayisflashing

"E:11"or"E:12",

Watercannotbeseen in drum.

Washingsolutionhasnot drainedcompletely.

Indicatorlight"rinse"is lit anddisplayisflashing

"E:13"withnowater remaininginthe drum

Waterisflowingoutfrom underneaththe machine.

Sudscomingoutofthe detergentdispenser.

Repeatedspinning.

Thelaundrywasnotspun. (Laundryisstillwet).

Unsatisfactorywashing result.

Detergentresidueonthe Somephosphate-freedetergentscontainwater-insoluble Brushoffspotswhenlaundryis dry. laundry, residuesthatmayappearaslightspotsonthe laundry.

Grayresidueonthe Dirtaccumulationfromointments,fats oroils. Addthe maximumamountofdetergentandselectthe laundry, highestpermissibletemperature.

Systemshakesor shudders Drumsystemsuspensioncanshiftduringspeedup,this Mixsmallandlargelaundrypiecesinloadto minimize whenpassingfromlowerto is notafailure, thiseffect. Makesurethe unitis level,seepage15. higherspeedspinning.

Waterfaucetnotturnedon. Turnonwaterfaucet.

Cyclecontinues.

Supplyhosekinkedorpinched.

Strainersinsupplyhoseclogged.

Aquastope Hosesafetyfeatureactivated.

Aquastope is triggered

Waterpressuretoolow.

Thisisnotafault. Thewaterlevelisbelowthevisiblepartof the drum.

Suds

Pumpis blocked

Thethreadofthesupplyhoseis nottight.

Leakinthedrainhose.

Toomuchsoapor non HEsoapused,pumpcouldnot

removesuds.

Thisisnotafault. Theunbalancedloaddetectionsystemisattemptingto

balancethe loadthroughrepeatedspins. Loadsizetoosmall.

Largeitemsof clothinghavebecomeentangledandcould notbedistributedevenlyin the drum.Forreasonsof safetythe high-speedspincyclewasautomatically prevented.

Excessivesudsduetotoomuchdetergent,non HE detergentused

Thedegreeofsoilingwashigherthanestimated.

Notenoughdetergent. Adddetergentaccordingto themanufacturer's

Eliminatethecause.

Cleanthewaterinletstrainers(seePage27). Checkfor safetyindicator(seepage13). Ifred,replace

hose. Closewaterfaucetandinvestigateleak.

Eliminatethecause.

Uselessdetergentforfuturewashloads.Detergents specificallydesignedfor yourHighEfficiencywasher producefewersudsandwill includethe letters"HE"on thepackaging.

Cleanthe waterdrainagepipeand/ordrainhose. Tightenthethread.

Replacethedrainhose. Mix1tablespoonof fabricsoftenerwith1 pt(1/2litre)of

waterandpourintothe detergentcompartment(donotdo thiswithoutdoor(waterproof)fabric)

Uselessdetergentforfuturewashloads.Detergents specificallydesignedfor yourHighEfficiencywasher

producefewersudsandwill includethe letters"HE"on thepackaging(lookforthe "HE"symbol).

Alwaysloadthedrumwithseverallargeand smallitems together.

Addmorelaundry.

Alwaysloadthe drumwithseverallargeandsmallitems together.

Mix1tablespoonof fabricsoftenerwith1 pint(1/2 liter)of waterandpourintothemaindetergentdispenser

chamber;reducetheamountof detergentused;useHE detergent.(lookforthe "HE"symbol).

Selectsuitablecycle or

Stainremoval asanadditionaloption.

specifications.

Ifthe fault cannot be eliminated with the aid of the above table, switch the appliance off, wait 5 seconds, switch the appliance on

again, select and start the cycle.

Ifthe fault continues, call customer service; see Page 31.

+ 74 hidden pages