Bosch SPX5ES55UC/30, SPX5ES55UC/26, SPX5ES55UC/28, SPV68U53UC/30, SPV68U53UC/28 Installation Guide
...
CO
CO
0
0
0
0
03
To avoid possible injury or property damage, Inspect theDishwasher
OBSERVE ALL WARNINGS AND CAUTIONS.
These instructions are intended for use by qualified
installers only. The dishwasher must be installed by
a qualified service technician or installer.
In addition to these instructions, the dishwasher
shall be installed to meet all electrical and
plumbing codes and ordinances (both national
and local).
Read these installation instructions completely
and follow them carefully. They will save you time
and effort and help to ensure safety and optimum
dishwasher performance.
iMPORTANT
The dishwasher drain hose must be installed
with a portion of it at least 20" (508 mm) off the
cabinet floor; otherwise the dishwasher may not
drain properly.
This dishwasher is intended for indoor
residential use only, and should not be used in
commercial food service establishments.
After unpacking the dishwasher and prior to
installation, thoroughly inspect the dishwasher for
possible freight or cosmetic damage. Report any
damage immediately. Cosmetic defects must be
reported within 30 days of installation.
NOTE: Do not discard any bags or items that come
with the original package until after the entire
installation has been completed.
NEW INSTALLATION - If the dishwasher is a
new installation, most of the work must be done
before the dishwasher is moved into place.
REPLACEMENT- If the dishwasher is replacing
another dishwasher, check the existing
dishwasher connections for compatibility with
the new dishwasher, and replace parts as
necessary.
This appliance has been found to be in
compliance with CAN/CSA-C22.2 No. 167/UL
749. It is the responsibility of the owner and the
installer to determine if additional requirements
and standards apply in specific installations.
,, Not for outdoor use.
1
Avoiding General Hazards _ Make sure electrical work is properly installed.
Do not use the dishwasher until it is completely
installed. When opening the door on an uninstalled
dishwasher, carefully open the door while
supporting the rear of the unit. Failure to follow this
warning can cause the dishwasher to tip over and
result in serious injury.
Before installing the "[="-shaped supplied countertop
mounting brackets (select models), decide which
method will be used to secure the dishwasher into
its opening. Once these mounting brackets are
installed on the dishwasher, removing them is
difficult and will damage the mounting brackets and
the dishwasher.
In some conditions, hydrogen gas can form in a hot
water system that has not been used for weeks.
Hydrogen gas is explosive.
Before filling a dishwasher from a system that has
been off for weeks, run the water from a nearby
faucet in a well ventilated area until there is no
sound or evidence of gas.
Temperatures required for soldering and sweating
will damage the dishwasher's base and water inlet
valve. If plumbing lines are to be soldered or
sweated, keep the heat source at least 6" (152.4
mm) away from the dishwasher's base and water
inlet valve.
Removing any cover or pulling the dishwasher from
the cabinet can expose hot water connections,
electrical power and sharp edges or points. Handle
with care.
Avoiding Electrical Shock/Fire Hazards
Do not allow the electrical and water supply lines to
touch. Separate channels are provided under the
dishwasher.
Do not work on an energized circuit. Doing so could
result in serious injury or death. Only qualified
electricians should perform electrical work. Do not
attempt any work on the dishwasher electric supply
circuit until you are certain the circuit is de-
energized.
A
There should be no loose electrical connections.
Ensure all electrical connections are properly made.
The customer has the responsibility of ensuring that
the dishwasher electrical installation is in
compliance with all national and local electrical
codes and ordinances. The dishwasher is designed
for an electrical supply of 120V, 60 Hz, AC,
connected to a dishwasher-dedicated, properly
grounded electrical circuit with a fuse or breaker
rated for 15 amps. Electrical supply conductors
shall be a minimum #14 AWG copper only wire
rated at 75°C (167°F) or higher.
This appliance must be connected to a grounded
metal, permanent wiring system, or an equipment-
grounding conductor must be run with the circuit
conductors and connected to the equipment-
grounding terminal or lead on the appliance. Do not
use extension cords.
Avoiding Electrical Shock/Fire Hazards
Do not perform any work on a charged hot water
line. Serious injury could result. Only qualified
plumber should perform plumbing work. Do not
attempt any work on the dishwasher hot water
supply plumbing until you are certain the hot water
supply is shut off.
Do not over tighten the 90 ° elbow. Doing so may
damage the water inlet valve and cause a water
leak.
Temperatures required for soldering and sweating
will damage the dishwasher's water inlet valve. If
plumbing lines are to be soldered or sweated, keep
the heat source at least 6" (152.4 mm) away from
the dishwasher's water inlet valve.
Check local plumbing codes for approved plumbing
procedures and accessories. All plumbing should
be done in accordance with national and local
codes.
These instructions depict an installation method for
stainless steel braided hose or PEX hot water
supply lines. If using copper tubing or other material
for water supply, defer to a licensed plumber for
proper installation.
2
Hammer HoleSaw PipeWrench AdjustableWrench
TapeMeasure
Wire Cutter Wire Stripper O 2 mm (1/16 in) Drill Level
SlotScrewdriver
Electrical Supply Cable - Minimum #14 AWG, 2 conductor, 1
ground, insulated copper conductors rated 75°C or higher
Hot Water Supply Line - Minimum 3/8" O.D. copper tubing or
metal braided dishwasher supply line
PhillipsScrewdriver
\-- '/
TorxT-20Screwdriver
Shut-off valve and fittings appropriate for hot water supply
line (copper tubing/compression fitting, or braided hose
UL listed conduit connector or strain relief is required if you
attach the field wiring directly to the terminal block
O 4x17mm
4x13 m
A Toe panel screws
B Mounting brackets
C Mounting bracket screws
D Toe panel (2pieces
E Screw clamp (for hose)
F Water supply adapter ntting
G Flexible edge protector for electrical wire
H Rubber drain hose adaptor
I Side mount force distributor (Alternate side mount only)
J Mounting bracket screws (Alternate side mount only)
K Installation Guide for fully integrated door panel (select
models only)
L Junction boyJpower supply
M Wrench (wrench size 13)
__-_" O4x36m m_7
4
Avoid Scalding or Electrical Shock Hazard!
Make sure the water supply and electrical supply are
shut off before installation or service.
NOTE: This dishwasher is designed to be enclosed on
the top and both sides by standard residential kitchen
cabinetry.
Select a location as close to the sink as possible for easy
access to water supply and drain lines. For proper
dishwasher operation and appearance, ensure that the
enclosure is square and has the dimensions shown in
Figure 1.
After locating the proper place for your new dishwasher,
you will need to create any required openings to allow for
passage of the water, drain and electrical line. In order to
avoid interference with the dishwasher when sliding it
into the cabinet, place your openings within the
dimensions shown in Figure 3.
Figure 1
NOTE: If your dishwasher opening width measures >18
in (458 mm) use the TOP OR SIDE MOUNT mounting
methods. If your dishwasher opening width measures
17z/_°- 18 in (450 - 458 ram) use the ALTERNATE SIDE
MOUNT mount-ing method.
If the dishwasher is to be installed in a corner, make sure
that there is adequate clearance to open the door. See
Figure 2.
Checkclearance
between
dishwasherdoor
andwall
Countertop
Figure 2
Figure 3
Required Openings;
4 3/4" X 2 3/8" (120 x 60 mm) - To pass the included
electrical supply junction box through to adjacent cabinet.
NOTE: If the incoming electric supply, water supply and
drain connections are all in the same cabinet, the one
43/4"X 23/8" (120 x 60 mm) hole will be large enough for
all three to pass through.
4" x 2" (100 x 50ram) - To pass the included water supply
line toward the water supply.
1!/4" (32 mm) diameter - To pass the dishwasher drain
hose toward the drain connection.
Before sliding the dishwasher into the cabinet,
remove the hose clip at the back of the dishwasher
as shown in Figure 4. The hose clip may be used
later to hold the drain hose as shown in Figure 9.
Avoid Electrical Shock/Fire Hazard!
Do not allow the electrical and water supply lines to touch.
Figure 4
Avoid Electrical Shock Hazard!
Do not work on an energized circuit. Doing so could
result in serious injury or death. Only qualified
electricians should perform electrical work. Do not
attempt any work on the dishwasher electric supply
circuit until you are certain the circuit is de-energized.
Avoid Fire Hazard!
Make sure electrical work is properly installed. Only
qualified electricians should perform electrical work.
Electrical Supply
The customer has the responsibility of ensuring that
the dishwasher electrical installation is in
compliance with all national and local electrical
codes and ordinances. The dishwasher is designed
for an electrical supply of 120V, 60 Hz, AC,
connected to a dishwasher-dedicated, properly
grounded electrical circuit with a fuse or breaker
rated for 15 amps. Electrical supply conductors
shall be a minimum #14 AWG copper wire rated at
75°C (167°F) or higher.
Electrical Connection
The dishwasher electrical supply junction box (L)
and dedicated receptacle must be mounted in an
accessible cabinet adjacent to the dishwasher (do
not mount the junction box or receptacle behind the
dishwasher). You will need a 43/4" x 23/8" (120 x
60 mm) opening through the cabinet in order to
pass the junction box through (see Figure 5). If the
opening is made through wood, sand it smooth. If
the opening is made through metal, use the
included edge protector (G) or other approved
method to protect wiring from damage. Use the four
screws included (or appropriate fastener) in the
parts bag to securely mount the junction box so that
it can be easily accessed (see Figure 5). The
electrical supply can be connected in two ways:
IRe_epta_*e_r/ I I
+ +
Avoid Fire Hazard!
Make sure there are no loose electrical connections.
Make sure all electrical connections are properly made.
Grounding Instructions
The dishwasher must be properly grounded before
operating. This appliance must be connected to a
grounded metal permanent wiring system or an
equipment grounding conductor must be run with
the circuit conductors and connected to the
equipment grounding terminal or lead on the
dishwasher. Make sure that the dishwasher is
connected to a suitable ground in compliance with
all local codes or, in the absence of a local code,
with the NATIONAL ELECTRICAL CODE in the
United States or the CANADIAN ELECTRIC CODE
C22.1-1atest edition in Canada as well as any
provincial/state or municipal or local codes that
apply.
Dishwasher Electrical Rating
/ / Im+-+++prong#_+
++++ +
Figure 5
Method A - Three prong plug and receptacle
Use the included three-prong plug and junction box
to connect to a dedicated household receptacle.
Make sure the household receptacle meets the
electrical supply requirements as well as national
and local codes.
60 12
6
1,300 (max)
Method B - To permanently connect to
household or field wiring
1. Remove the dishwasher electrical supply junction
box (Part L) cover and connect to the power
supply cord from the house installation. See
Figure 6.
Figure 6
2. Remove 2" to 3" (51 - 76 mm) of the outer
casing of the household or field supply wiring as
shown in Figure 7. Remove 3/8" to 1/2" (10 - 13
mm) of the insulation from each wire as shown in
Figure 7.
_ (51m 76mm)
Hot Water Supply
The hot water heater should be set to deliver
approximately 120 ° F (49 ° C) water to the
dishwasher. Water that is too hot can cause some
detergents to lose effectiveness. Lower water
temperatures will increase run times. The hot water
supply pressure must be between 15 - 145 psi (1 -
i0 bar).
IMPORTANT NOTES:
,, If using a solder joint instead of a compression
fitting, be sure to make all solder connections
before connecting the water supply line to the
dishwasher.
,, Make sure there are no sharp bends or kinks in
the water line that might restrict water flow.
,, Always use the appropriate seal when making
plumbing connections.
,, Before connecting the water supply line to the
dishwasher, flush the incoming water line for
approximately 5 minutes to clear any foreign
material.
,, Turn on the water supply and check for leaks
after connections are made.
3/8"- 1/2" )I_ _1_
(10ram - 13ram)
Figure 7
3. Insert the bare copper or green wire(ground) to
the "G" __L_=_ground connection of the terminal
block and securely tighten the terminal block
screw (see Figure 6).
4. Insert the white (neutral) wire to the "N"
connection of the terminal block and securely
tighten the terminal block screw.
5. Insert the black (hot) wire to the "L" connection of
the terminal block and securely tighten the
terminal block screw.
6. Check all electrical connections to make sure
they are secure and then attach the junction box
cover with the 4 screws.
Avoid Electrical Shock Hazard!
To avoid possible injury or property damage, care should
be exercised when the dishwasher is installed or removed
to reduce the likelihood of damage to the power cord.
Avoid Scald Hazard!
Do not perform any work on a charged hot water line.
Serious injury could result. Only qualified plumbers should
perform plumbing work. Do not attempt any work on the
dishwasher hot water supply plumbing until you are certain
the hot water supply is shut off.
Temperatures required for soldering and sweating will
damage the dishwasher. If plumbing lines are to be
soldered or sweated, keep the heat source at least 6
inches (152.4 mm) away from the dishwasher.
Water Supply Shut Off Valve
Install an easily accessible shut-off valve (not
supplied) in the hot water supply line, as shown in
Figure 8. All solder connections must be made before
the water line is connected to the dishwasher.
Connecting the Hot Water Supply
There are two plastic corrugated hoses that exit the
back of the dishwasher. The larger hose, with the
brass fitting on the end, is the water supply hose to
the dishwasher (the other hose is the dishwasher
drain hose). You will need a 3" x 13/4" (76 x 45 mm)
opening through the cabinet to pass the dish-washer
water supply line through toward the shut off valve.
Loading...