Bosch CC488, Solution Ultima 880 Quick Reference Manual

EN

Quick Reference Guide

Solution Ultima 880

CC488

CC488 | Quick Reference Guide | Notices EN | 2

Bosch Security Systems | 6/04 | 4998152446B

Copyright Notice

Unless otherwise indicated, this publication is the
copyright of Bosch Security Systems Pty Ltd
(“Bosch”). All rights are reserved.

You may download a single copy of this publication.
By downloading the publication you agree that you
will: (i) only use the publication for your own
reference; (ii) not commercially exploit or charge any
person for the use of the publication; and (iii) not
modify the publication in any way without the prior
written permission of Bosch.

Except as specified above or where authorised by the
Copyright Act 1968 (Cth), no part of this publication
may be reproduced, transmitted, modified or stored,
in any form or by any means, without the prior
written permission of Bosch.

Notice of Liability

This material is designed for use by tradespeople with
expertise in the installation of this product. Persons
without appropriate expertise should seek assistance
before attempting installation.

While care has been taken in the preparation of this
material, Bosch Security Systems Pty Ltd and its
representatives will not be responsible to any person
or entity for any loss or damage directly or indirectly
caused by information in, or any omission from, this
material.

Bosch Security Systems Pty Ltd reserves the right to
make changes to features and specifications of its
products at any time without prior notification.

CC488 | Quick Reference Guide | Contents EN | 3

Bosch Security Systems | 6/04 | 4998152446B

Contents

1.0 Overview ...........................................................6

1.1 Introduction.......................................................6

1.2 Programming..................................................... 6

1.3 Programming Using A Codepad .................... 6

1.4 Programming Option Bits................................7

1.5 Installer’s Programming Commands.............. 7

1.6 Arming/Disarming the System .......................8

1.7 Isolating Zones ..................................................8

1.7.1 Standard Isolating............................................. 8

1.7.2 Code to Isolate.................................................. 8

1.8 Add/Delete RF Devices (Wireless Zones) .....8

1.8.1 Add RF Device .................................................8

1.8.2 Delete RF Device..............................................8

1.9 Set First Test Report.........................................8

1.10 Event Memory Recall ......................................8

1.11 Walk Test Mode ............................................... 8

1.12 Satellite Siren Service Mode............................9

1.13 Telephone Monitor Mode (Toggle

On/Off).............................................................. 9

1.14 Add/Delete User Code/RF Keyfob................9

1.14.1 Add A User Code.............................................9

1.14.2 Add RF Keyfob................................................. 9

1.14.3 Delete a User Code/RF Keyfob......................9

1.15 Change Domestic Telephone Numbers......... 9

1.16 Turn Outputs On/Off ......................................9

1.17 Setting Date and Time ..................................... 9

1.18 Day Alarm – Toggle On/Off ..........................9

1.19 STAY Mode 2 Zones – Program ....................9

1.20 Fault Analysis ..................................................10

1.21 Modem Call (Alarm Link).............................10

1.22 Latching Outputs (Reset) ...............................10

1.23 Codepad ID/Buzzer Tone .............................10

1.24 Test Report......................................................10

1.25 Speaker Test ....................................................10

1.26 Bell Test ...........................................................10

1.27 Strobe Test (Toggle On/Off)......................... 10

1.28 Telco Arm Sequence (Call Forward On).....10

1.29 Telco Disarm Sequence (Call Forward

Off) ...................................................................10

2.0 Programming Parameters ..............................11

2.1 Phone Programming.......................................11

2.1.1 Phone Number 1 - Receiver 1.......................11

2.1.2 Phone Number 2 - Receiver 1.......................11

2.1.3 Handshake Tone For Receiver 1..................11

2.1.4 Transmission Format For Receiver 1 ...........11

2.1.5 Subscriber ID Number For Receiver 1........11

2.1.6 Phone Number 1 - Receiver 2.......................11

2.1.7 Phone Number 2 - Receiver 2.......................11

2.1.8 Handshake Tone For Receiver 2 ..................11

2.1.9 Transmission Format For Receiver 2 ...........11

2.1.10 Subscriber ID Number For Receiver 2 ........11

2.1.11 Dialling Format ...............................................11

2.1.12 Reserved ..........................................................11

2.1.13 Telco Arming Sequence (Call Forward

On)....................................................................11

2.1.14 Telco Disarm Sequence (Call Forward

Off)....................................................................11

2.1.15 Call Back Telephone Number.......................11

2.1.16 Ring Count ......................................................11

2.1.17 Telephone Line Fail Options.........................12

2.1.18 Dialler Options 1 ............................................12

2.1.19 Dialler Options 2 ............................................12

2.1.20 Dialler Options 3 ............................................12

2.1.21 Dialler Options 3 (V1.04+)............................12

2.1.22 Alarm Link Options .......................................12

2.2 Installer Code..................................................12

2.3 User Code Programming...............................12

2.3.1 User Codes ......................................................12

2.3.2 Authority Levels..............................................12

2.4 Day Alarm Zones............................................13

2.5 EOL Resistor Value........................................13

2.6 Zone Programming.........................................13

2.6.1 Zone Defaults ..................................................13

2.6.2 Zone Types......................................................14

2.6.3 Zone Pulse Count............................................14

2.6.4 Zone Pulse Count Time .................................14

2.6.5 Zone Options 1 ...............................................14

2.6.6 Zone Options 2 ...............................................14

2.6.7 Zone Dialler Options......................................14

2.6.8 Keyswitch Zone Options................................14

2.7 Swinger Programming....................................14

2.7.1 Swinger Shutdown Count For Siren.............14

2.7.2 Swinger Shutdown Count For Dialler ..........14

2.8 Zone Status Programming..............................14

2.8.1 Zone Status – Zone Tamper Report .............14

2.8.2 Zone Status – Walk Test Report ...................14

2.8.3 Zone Status – Bypass Report.........................14

2.8.4 Zone Status – Trouble Report.......................14

2.8.5 Zone Status – Sensor Watch Report.............15

2.8.6 Zone Status – Alarm Restore Code ..............15

2.8.7 Zone Status Reporting Options.....................15

2.9 RF Programming.............................................15

2.9.1 RF Supervision Time......................................15

2.9.2 RF Low Battery Report..................................15

2.9.3 RF Receiver Trouble Report.........................15

2.9.4 RF Receiver Trouble Restore Report...........15

2.9.5 RF Dialler Options .........................................15

2.10 Report Programming......................................15

2.10.1 Open/Close Reports.......................................15

CC488 | Quick Reference Guide | Contents EN | 4

Bosch Security Systems | 6/04 | 4998152446B

2.10.2

Open/Close Reporting Options....................15

2.10.3 Codepad Duress Report.................................15

2.10.4 Codepad Panic Report...................................15

2.10.5 Codepad Fire Report......................................15

2.10.6 Codepad Medical Report ..............................15

2.10.7 Codepad Reporting Options......................... 15

2.11 System Status Programming..........................15

2.11.1 System Status – Fuse Fail Report..................15

2.11.2 System Status – Fuse Fail Restore Report....15

2.11.3 System Status – AC Fail Report....................15

2.11.4 System Status – AC Fail Restore Report .....16

2.11.5 System Status – Low Battery Report ............16

2.11.6 System Status – Low Battery Restore

Report ..............................................................16

2.11.7 System Status – Access Denied (Code

Retry)................................................................16

2.11.8 System Status Reporting Options .................16

2.12 Test Report Programming .............................16

2.12.1 Test Report Time (Automatic) ......................16

2.12.2 Test Reporting Dailler Options.....................16

2.13 Output Programming .....................................16

2.13.1 Outputs ............................................................16

2.13.2 Event Codes ....................................................17

2.13.3 Polarity (Modes).............................................. 18

2.13.4 Time Base ........................................................18

2.13.5 Time Base Multiplier......................................18

2.13.6 One Shot Mode ..............................................18

2.13.7 Pulsing Mode...................................................18

2.14 Time Programming ........................................18

2.14.1 Entry Time 1 ...................................................18

2.14.2 Entry Time 2 ...................................................18

2.14.3 Exit Time (AWAY/STAY Modes) ...............18

2.14.4 Entry Guard Time For STAY Mode............18

2.14.5 Delay Alarm Report Time.............................18

2.14.6 Sensor Watch Time ........................................18

2.14.7 Codepad Lockout Time.................................18

2.14.8 Siren Run Time...............................................18

2.14.9 Siren Sound Rate ............................................18

2.14.10 Auto Arming Pre-Alert Time ........................18

2.14.11 Auto Arming Time .........................................18

2.14.12 Auto Disarming Time ....................................18

2.14.13 Kiss-Off Wait Time.........................................18

2.14.14 Speaker Beep Volume....................................19

2.15 Options Programming....................................19

2.15.1 System Options 1............................................19

2.15.2 System Options 2............................................19

2.15.3 System Options 3............................................19

2.15.4 System Options 4............................................19

2.15.5 Consumer Options 1 ......................................19

2.15.6 Consumer Options 2 ......................................19

2.15.7 Consumer Options 3 ......................................19

2.15.8 Radio Input Options.......................................19

2.15.9 Partitioning Options 1 ....................................19

2.15.10 Partitioning Options 2 ....................................19

2.16 Zone Allocations Programming ....................19

2.16.11 Zone Allocations for Area 1 ..........................19

2.16.12 Zone Allocations for Area 2 ..........................19

2.17 User Code Area Assignment.........................20

2.18 Domestic Telephone Numbers .....................20

2.19 Reserved ..........................................................20

2.20 RF Programming.............................................20

2.20.1 RF Options ......................................................20

2.20.2 RF Device Mapping for Devices 1 to 8........20

2.20.3 RF Device Mapping for Devices 9 to 16 .....20

2.20.4 Ring Burst Time (V1.07+) .............................20

2.20.5 RF Signal Strength for Devices 1 to 8 ..........20

2.20.6 RF Signal Strength for Devices 9 to 16 ........20

2.21 System Option Programming........................20

2.21.7 Default Options...............................................20

2.21.2 System Time....................................................20

2.21.3 System Date.....................................................21

3.0 Solution Ultima RF Receiver Interface........22

4.0 RF Keyfob Operations ...................................23

5.0 Connections for Split EOL Resistors............23

5.1 8 Burglary Zones.............................................23

5.2 8 Zone Operation Using N/O Contacts.......24

6.0 Wiring Diagrams.............................................24

6.1 Keyswitch Zone...............................................24

6.2 Solution Ultima Series....................................25

7.0 Component Overlay.......................................26

8.0 Codepad Connections Partitioning...............27

CC488 | Quick Reference Guide | Contents EN | 5

Bosch Security Systems | 6/04 | 4998152446B

Figures

Figure 1: RF Receiver (RF 3212/E) Wiring

Diagram.................................................... 22

Figure 2: RF3332/E – 2 Button RF Keyfob..........23

Figure 3: RF3332/E – 4 Button RF Keyfob..........23

Figure 4: Split EOL Wiring Diagram (Location

266 = 15) ..................................................23

Figure 5: Split EOL Wiring Diagram with Tamper

(Location 266 = 14).................................23

Figure 6: Split EOL Wiring Diagrams Using N/O

Contacts.................................................... 24

Figure 7: Wiring Diagram for Keyswitch Zone....24

Figure 8: Solution Ultima Series Wiring

Diagram.................................................... 25

Figure 9: Solution Ultima Series Component

Overlay.....................................................26

Figure 10: Connections for CP-5 Master Partitioned

(CP500P) Codepad and CP-5 Area

Addressable (CP500A) Codepad...........27

Figure 11: Connections for Two CP-5 Eight Zone

Area Addressable (CP500A)

Codepads..................................................27

Tables

Table 1: Quick Guide to Programming..................6

Table 2: Codepad Indicators ...................................7

Table 3: Programming Option Bits.........................7

Table 4: Installer’s Programming Commands .......7

Table 5: Arming/Disarming the System ................8

Table 6: Telephone Monitor Mode ........................9

Table 7: Fault Analysis Conditions .......................10

Table 8: Codepad ID/Buzzer Tone ......................10

CC488 | Quick Reference Guide | 1.0 Overview EN | 6

Bosch Security Systems | 6/04 | 4998152446B

1.0 Overview

1.1 Introduction

Thank you for choosing the Solution Ultima 880
Control Panel (model CC488) for your installation.
You will find this system extremely flexible, reliable,
and easy to use. This Quick Reference Guide is supplied
with the system to provide users with enough basic
information to wire, configure, and program the
system. Due to the systems many programmable
features and options, we suggest that you obtain the
CC484/CC486/CC488 Installation Manual that
provides detailed information on system options,
functions, and programming methods.

1.2 Programming

The programming options of the system are stored in
a non-volatile EPROM. This memory holds all
information during a total power loss and can be
changed as many times as required.

The entire programming sequence consists of
entering a location number and changing the data as
required.

Use the following methods to program the system:

• Codepad

• Hand Held Programmer

• Alarm Link Software

1.3 Programming Using A Codepad

The system must be disarmed (with no active alarm)
to program the system. If there is an active alarm or
the system is armed, enter the code for User 1
(Default = 2580) followed by the [#] key. (User Code
1 is factory default as the Master Code.)

To enter Installer’s Programming Mode, enter the
installer code (Default = 1234) followed by the [#]
key. Two beeps are heard and both the STAY and
AWAY indicators flash simultaneously to indicate
that you entered programming mode. The codepad
indicators displays the current data programmed in
LOCATION 000 (first location of the Primary
Telephone Number).

To move to another programming location, enter the
location number followed by the [#] key. The data in
the new location is displayed using the codepad
indicators. (For example, if you enter [3 4 #], the
system jumps to LOCATION 034, the beginning of
the Subscriber ID Number For Receiver 1.)

To move to the next location, press the [#] key. This
steps you to the next location. The data in the next
location is displayed using the codepad indicators.
(For example, if you are currently positioned at
LOCATION 034, pressing the [#] key takes you to
LOCATION 035.)

To step back one location, press the [*] key. (For
example, if you are currently positioned at
LOCATION 35, pressing the [*] key returns to
LOCATION 34.)

To change data in the current location, enter the new
value (0 to 15) followed by the [*] key. This stores the
new data into the location. (For example, if you enter
the value [1 4 *], both the Zone 4 indicator and the
MAINS indicator display to represent the new data
value.)

To move to the next location, press the [#] key. The
data in the next location displays.

To exit Installer’s Programming Mode, enter
[9 6 0 #]. Two beeps are heard and the STAY and
AWAY indicators no longer display. The system
returns to the disarmed state and is ready for use.

Table 1 displays a quick guide to programming:

Table 1: Quick Guide to Programming

Task Keystrokes

Enter Installer’s Programming
Mode

[1 2 3 4 #]

Exit Installer’s Programming
Mode

[9 6 0 #]

Step to next Location [#]
Step back one Location [*]
Program new data into

Location

[Data][*] (Data = 0 to 15)

Jump to another Location [Location No.][#]

CC488 | Quick Reference Guide | 1.0 Overview EN | 7

Bosch Security Systems | 6/04 | 4998152446B

Table 2: Codepad Indicators

Data
Value

Zone 1
Indicator

Zone 2
Indicator

Zone 3
Indicator

Zone 4
Indicator

Zone 5
Indicator

Zone 6
Indicator

Zone 7
Indicator

Zone 8
Indicator

MAINS
Indicator

0
1 X
2 X
3 X
4 X
5 X
6 X
7 X
8 X
9 X X
10 X
11 X X
12 X X
13 X X
14 X X
15 X X

1.4 Programming Option Bits

Use option bits to program any combination of the
four different options in one location by adding
the options together. Programming a zero disables
all four options.

Example

If at LOCATION 177 you only want options 1, 2,
and 4, add the numbers together and the total is
the number to be programmed. The number to be
programmed is 7 (1 + 2 + 4 = 7).

Table 3: Programming Option Bits

Option Description

1 Dialler reporting functions allowed
2 Remote arming using telephone allowed
4 Answering machine bypass only when armed
8 Use bell 103 for FSK format

(Disabled = CCITT V21)

1.5 Installer’s Programming
Commands

Installer Programming Commands, displayed in
Table 4, can only be used when you enter
Installer’s Programming Mode. Enter the
command followed by the [#] key.

Table 4: Installer’s Programming Commands

Command Description

958 Enable/disable zone status (hand held programmer

required).
959 Test programming key.
960 Exit Installer’s Programming Mode.
961 Default system back to factory settings.
962 Copy panel memory to programming key.
963 Copy programming key to panel memory.
964 Erase programming key.
965 Default system for domestic dialling format.
966 Enable/disable automatic stepping of locations

when programming.
999 Display software version (hand held programmer

required).

CC488 | Quick Reference Guide | 1.0 Overview EN | 8

Bosch Security Systems | 6/04 | 4998152446B

1.6 Arming/Disarming the System

1.7 Isolating Zones

1.7.1 Standard Isolating

1. Press the [*] key twice.

2. Enter the zone number that you want isolated,
followed by the [*] key.
Repeat step 2 if more than one zone is
required to be isolated.

3. Press the [#] key to exit when finished.

1.7.2 Code to Isolate

1. Press the [*] key once.

2. Enter your user code.

3. Enter the zone number that you want isolated,
followed by the [*] key.
Repeat Step 2 if more than one zone is
required to be isolated.

4. Press the [#] key to exit when finished.

1.8 Add/Delete RF Devices (Wireless

Zones)

1.8.1 Add RF Device

1. Enter the four character Installer Code,
followed by [0] and the [#] key (for example,
[1 2 3 4 0 #]).

2. Enter the Device Number (1 to 16) you want
to add, followed by the [#] key.

3. Enter the 9-digit RF device ID number,
followed by the [#] key.

1.8.2 Delete RF Device

1. Enter the Installer Code followed by [0] and
the [#] key (for example, [1 2 3 4 0 #]).

2. Enter the Device Number (1 to 16) you want
to delete, followed by the [#] key.

3. Press the [*] key to delete the RF device.

1.9 Set First Test Report

1. Enter the four character Installer Code,
followed by [1] and the [#] key (for example,
[1 2 3 4 1 #]).

2. Enter the Number Of Days (0 to 15) to wait
until the first test report, followed by the [#]
key.

1.10 Event Memory Recall

Enter the four character Installer Code or Master
Code, followed by [8] and the [#] key (for
example, [1 2 3 4 8 #]).

The last 40 events (non partitioned) or last ten
events (partitioned) are displayed in reverse order
(for example, most recent to least recent).

1.11 Walk Test Mode

1. Enter the four character Installer Code or
Master Code, followed by [7] and the [#] key
(for example, [1 2 3 4 7 #]).

2. Test each zone as required.

3. Press the [#] key to exit.

Table 5: Arming/Disarming the System

AWAY Mode STAY Mode 1 STAY Mode 2

Arming
(On)

Press and hold the [#] key until two
beeps are heard.

Or
Enter your code followed by the [#]

key (for example, [2 5 8 0 #]).
Or
To arm all areas, enter your code

followed by [0] and then the [#] key
(for example, [2 5 8 0 0 #]).

Use a code to arm all areas
simultaneously that the code is
assigned to in AWAY Mode without
needing to arm each area individually.

Press and hold the [*] key until two
beeps are heard.

Or
Enter your code followed by the [*]

key (for example, [2 5 8 0 *]).

Press and hold the [0] key until two
beeps are heard.

Disarming
(Off)

Enter your code followed by the [#]
key (for example, [2 5 8 0 #]).

Or
To disarm all areas, enter your code

followed by [0] and then the [#] key
(for example, [2 5 8 0 0 #]).

Use a code to disarm all areas
simultaneously that the code is
assigned without needing to disarm
each area individually.

Press and hold the [*] key until two
beeps are heard (only if no alarm).

Or
Enter your code followed by the [#]

key (for example, [2 5 8 0 #]).

Press the [0] key until two beeps are
heard (only if no alarm).

Or
Enter your code followed by the [#]

key (for example, [2 5 8 0 #]).

CC488 | Quick Reference Guide | 1.0 Overview EN | 9

Bosch Security Systems | 6/04 | 4998152446B

1.12 Satellite Siren Service Mode

Enter the four character Installer Code, followed
by [5] and the [#] key (for example, [1 2 3 4 5 #]).

1.13 Telephone Monitor Mode (Toggle
On/Off)

1. Enter the four character Installer Code,

followed by [6] and the [#] key (for example,
[1 2 3 4 6 #]).

2. Press and hold the [9] key until two beeps are

heard to send a test report.

Table 6: Telephone Monitor Mode

Zone LED Dialling Event

1 Telephone Line Seized
2 Dialling Telephone Number
3 Handshake Received
4 Data Being Sent
5 Kiss-Off Received
None Released Telephone Line

1.14 Add/Delete User Code/RF
Keyfob

1.14.1 Add A User Code

1. Enter the four character Master Code,

followed by [1] and the [#] key (for example,
[2 5 8 0 1 #]).

2. Enter the User Number (1 to 16) you want to

add/change, followed by the [#] key.

3. Enter the new code, followed by the [#] key.

1.14.2 Add RF Keyfob

1. Enter the four character Master Code,

followed by [1] and the [#] key (for example,
[2 5 8 0 1 #]).

2. Enter the User Number (9 to 16) you want to

add, followed by the [#] key.

3. Enter the 9-digit RF keyfob ID number,

followed by the [#] key.

1.14.3 Delete a User Code/RF Keyfob

1. Enter the four character Master Code,

followed by [1] and the [#] key (for example,
[2 5 8 0 1 #]).

2. Enter the User Number (1 to 16) you want to

delete, followed by the [#] key.

3. Press the [*] key to delete the User Code.

1.15 Change Domestic Telephone
Numbers

1. Enter the four character Installer Code or

Master Code, followed by [2] and the [#] key
(for example, [1 2 3 4 2 #]).

2. Enter the digits for the telephone number.

3. If there is more than one telephone number,

press the [*] key, followed by the [4] key
(inserts break between phone numbers) and
repeat Step 2, or press the [#] key to exit.

1.16 Turn Outputs On/Off

1. Enter the four character Master Code,

followed by [5] and the [#] key (for example,
[2 5 8 0 5 #]).

2. Enter the Output Number (1 to 3) you want to

toggle on or off.

3. Press the [#] key to toggle on or the [*] key to

toggle off.

4. Press the [#] key to exit.

1.17 Setting Date and Time

1. Enter the four character Master Code,

followed by [6] and the [#] key (for example,
[2 5 8 0 6 #]).

2. Enter the day (DD), month (MM), and year

(YY) followed by the hour (HH) and minute
(MM).

3. Press the [#] key to exit.

1.18 Day Alarm – Toggle On/Off

Press and hold the [4] key until two beeps are
heard. Day alarm toggles on or off.

1.19 STAY Mode 2 Zones – Program

1. Enter the four character Installer Code or

Master Code, followed by [4] and the [#] key
(for example, [1 2 3 4 4 #]).

2. Enter the Zone Number you want the system

to automatically isolate, followed by the [*]
key.
Repeat if more than one zone must be
automatically isolated when armed in STAY
Mode 2.

3. Press the [#] key to exit.