Page 1
3FHJTUFSZPVSOFX#PTDIOPX
XXXCPTDIIPNFDPNXFMDPNF
Dishwasher
SM...
SB...
aus Instruction manual
Page 2
6HWXSVHF
Ù
5HVHWVHF
Page 3
aus
Table of contents
enInstruction manual
8 Intended use . . . . . . . . . . . . . . . 5
( Safety instructions. . . . . . . . . . . . 5
Before you switch ON the appliance 6
Delivery. . . . . . . . . . . . . . . . . . . . . . . . 6
Installation. . . . . . . . . . . . . . . . . . . . . . 6
In daily use . . . . . . . . . . . . . . . . . . . . . 7
Damage . . . . . . . . . . . . . . . . . . . . . . . 8
Disposal . . . . . . . . . . . . . . . . . . . . . . . 8
Door lock . . . . . . . . . . . . . . . . . . . . . . 9
7 Environmental protection . . . . . 11
Packaging. . . . . . . . . . . . . . . . . . . . . 11
Old appliances . . . . . . . . . . . . . . . . . 11
* Getting to know your appliance 11
Control panel . . . . . . . . . . . . . . . . . . 11
Appliance interior . . . . . . . . . . . . . . . 12
Info button . . . . . . . . . . . . . . . . . . . . 12
Time setting . . . . . . . . . . . . . . . . . . . 12
Switching on the appliance
for the first time. . . . . . . . . . . . . . . . . 13
Settings. . . . . . . . . . . . . . . . . . . . . . . 14
- Utensils. . . . . . . . . . . . . . . . . . . . 17
Not suitable . . . . . . . . . . . . . . . . . . . . 17
Glass and utensil damage. . . . . . . . . 17
Loading the dishwasher . . . . . . . . . . 18
Upper basket. . . . . . . . . . . . . . . . . . . 18
Lower basket. . . . . . . . . . . . . . . . . . . 18
Cutlery basket . . . . . . . . . . . . . . . . . . 19
Cutlery drawer . . . . . . . . . . . . . . . . . . 19
Etagere . . . . . . . . . . . . . . . . . . . . . . . 20
Folding spikes . . . . . . . . . . . . . . . . . . 20
Small items holder. . . . . . . . . . . . . . . 20
Knife rack . . . . . . . . . . . . . . . . . . . . . 21
Baking sheet spray head. . . . . . . . . . 21
Unloading the dishwasher . . . . . . . . . 22
Adjusting the height of the basket. . . 22
. Detergent . . . . . . . . . . . . . . . . . . 24
Adding detergent. . . . . . . . . . . . . . . . 24
/ Overview of programmes . . . . . 26
Programme selection . . . . . . . . . . . . 27
Information for test institutes . . . . . . . 27
0 Additional functions . . . . . . . . . 28
, Rinse aid . . . . . . . . . . . . . . . . . . . 16
Setting amount of rinse aid. . . . . . . . 16
Switching off rinse aid refill
indicator . . . . . . . . . . . . . . . . . . . 17
Express Wash/ Speed Perfect
(VarioSpeed) . . . . . . . . . . . . . . . . . . . 28
Half load . . . . . . . . . . . . . . . . . . . . . . 28
hygienePlus (HygienePlus) . . . . . . . . 28
intensiveZone . . . . . . . . . . . . . . . . . . 28
Shine and Dry . . . . . . . . . . . . . . . . . . 28
3
Page 4
aus
1 Operating the appliance . . . . . . 29
Changing the settings . . . . . . . . . . . . 29
AquaSensor . . . . . . . . . . . . . . . . . . . . 29
Zeolith drying. . . . . . . . . . . . . . . . . . .30
Time display . . . . . . . . . . . . . . . . . . . 30
Sensor setting . . . . . . . . . . . . . . . . . .30
extraDry . . . . . . . . . . . . . . . . . . . . . . . 30
Eco forecast . . . . . . . . . . . . . . . . . . .30
Auto Power Off . . . . . . . . . . . . . . . . . 31
EmotionLight . . . . . . . . . . . . . . . . . . . 31
Front display . . . . . . . . . . . . . . . . . . .31
timeLight . . . . . . . . . . . . . . . . . . . . . .31
infoLight . . . . . . . . . . . . . . . . . . . . . . . 31
Changing start programme . . . . . . . .31
Tone volume . . . . . . . . . . . . . . . . . . .31
Button volume . . . . . . . . . . . . . . . . . .32
Child-proof lock . . . . . . . . . . . . . . . . .32
Greeting. . . . . . . . . . . . . . . . . . . . . . .32
Factory setting . . . . . . . . . . . . . . . . . .32
Switching the appliance on . . . . . . . . 32
Time preselection . . . . . . . . . . . . . . . 32
Programme end. . . . . . . . . . . . . . . . . 32
Switching off the appliance . . . . . . . . 33
Interrupting the programme . . . . . . . . 33
Terminating the programme . . . . . . . 33
Changing the programme . . . . . . . . .33
4 Customer service . . . . . . . . . . . . 45
5 Installation and connection. . . .45
Contents of package . . . . . . . . . . . . 45
Safety instructions . . . . . . . . . . . . . . 45
Delivery . . . . . . . . . . . . . . . . . . . . . . 46
Technical specifications . . . . . . . . . . 46
Installation . . . . . . . . . . . . . . . . . . . . 46
Drainage connection . . . . . . . . . . . . 46
Drinking water connection . . . . . . . . 47
Warm water connection . . . . . . . . . . 47
Electrical connection . . . . . . . . . . . . 48
Removal . . . . . . . . . . . . . . . . . . . . . . 48
Transporting . . . . . . . . . . . . . . . . . . . 49
Protection against frost (Emptying
the appliance) . . . . . . . . . . . . . . . . . 49
2 Cleaning and maintenance . . . 34
Overall condition of the machine . . . .34
Rinse aid . . . . . . . . . . . . . . . . . . . . . .34
Filters. . . . . . . . . . . . . . . . . . . . . . . . .35
Spray arms . . . . . . . . . . . . . . . . . . . .35
3 Fault, what to do?. . . . . . . . . . . 36
Error message . . . . . . . . . . . . . . . . . . 36
Waste water pump. . . . . . . . . . . . . . . 36
Fault table . . . . . . . . . . . . . . . . . . . . . 38
4
Page 5
Intended use aus
8 Intended use
Intended use
■ This appliance is intended
for use in the home and
domestic environments.
■ Use the dishwasher only in
the home and only for its
designated purpose: for
washing domestic dishes.
■ This appliance is intended
for use up to a maximum
altitude of 2500 metres
above sea level.
( Safety instructions
Safety instructions
This appliance may be used by
children over the age of 8 years
old and by persons with
reduced physical, sensory or
mental capabilities or by
persons with a lack of
experience or knowledge if they
are supervised or are instructed
by a person responsible for
their safety how to use the
appliance safely and have
understood the associated
hazards.
Children must not play with, on,
or around the appliance.
Children must not clean the
appliance or carry out general
maintenance unless they are at
least 8 years old and are being
supervised.
Keep children below the age of
8 years old at a safe distance
from the appliance and power
cable.
5
Page 6
aus Safety instructions
Before you switch ON the
appliance
Please read the instructions for
use and installation carefully.
They contain important
information on how to install,
use and maintain the appliance.
Retain all documents for later
use or for the subsequent
owner.
You can download the
instructions for use from our
website free of charge. The
relevant Internet address can
be found overleaf on these
instructions for use.
Delivery
1. Check the packaging and
dishwasher immediately for
damage caused in transit.
Do not switch on a damaged
appliance, but contact your
supplier.
2. Please dispose of the
packaging material in an
environmentally friendly
manner.
3. Do not let children play with
packaging and its parts.
There is a risk of suffocation
from collapsible boxes and
film.
Installation
■ Following installation, ensure
that the back of the
dishwasher is not freely
accessible (protection
against contact due to hot
surface).
■ Install and connect the
appliance according to the
installation and assembly
instructions.
■ Prior to installation,
disconnect the dishwasher
from the power supply.
■ Ensure that the protective
conductor system of the
domestic supply has been
correctly installed.
■ The electrical connection
conditions must correspond
with the specifications on the
dishwasher rating plate 9B.
■ If the power cord of this
appliance is damaged, it
must be replaced with a
particular power cord.
To prevent injury, the power
cord may be purchased from
customer service only.
■ If the dishwasher is installed
in a high-sided unit, the unit
must be secured properly.
■ If the dishwasher is installed
below or above other
domestic appliances, follow
the information for
installation in combination
with a dishwasher in the
installation instructions for
the particular appliances.
6
Page 7
Safety instructions aus
■ Also follow the installation
instructions for the
dishwasher to ensure that all
appliances are operated
safely.
■ If there is no information or if
the installation instructions
do not include the
appropriate information,
contact the manufacturer of
these appliances to ensure
that the dishwasher can be
installed above or below
these appliances.
■ If you cannot obtain any
information from the
manufacturer, you must not
install the dishwasher above
or below these appliances.
■ If you install a microwave
oven above the dishwasher,
the microwave oven may be
damaged.
■ Install built-under or
integratable appliances only
under continuous worktops
which have been screwed to
adjacent cupboards to
ensure stability.
■ Do not install the appliance
near heat sources (radiators,
heat storage tanks, cookers
or other appliances which
generate heat) and do not
install under a hob.
■ Please note that the
insulation material of the
dishwasher power cord may
melt next to heat sources
(e.g. heating / hot water
installations) or hot
appliance parts. Make sure
that the power cord of the
dishwasher never comes into
contact with heat sources or
hot appliance parts.
■ After installing the appliance,
ensure that the plug is easily
accessible. ~ "Electrical
connection" on page 48
■ For some models:
The plastic housing on the
water connection contains an
electric valve. The supply
hose contains electrical
connection cables. Do not
cut through the supply hose.
Do not immerse the plastic
housing in water.
In daily use
Read and observe the safety
information and instructions for
use on the packaging for
cleaning and rinsing agents.
7
Page 8
aus Safety instructions
Damage
■ The appliance may be
repaired and opened up by a
technician only. To do this,
disconnect the appliance
from the power supply. Pull
out the mains plug or switch
off the fuse. Turn off the tap.
■ If the appliance is damaged,
especially the control panel
(cracks, holes, broken
buttons), or the door function
is impaired, stop operating
the appliance. Pull out the
mains plug or switch off the
fuse. Turn off tap, call
customer service.
Disposal
1. Make redundant appliances
unusable to prevent
subsequent accidents.
2. Dispose of the appliance in
an environmentally friendly
manner.
:Warning
Risk of injury!
■ To prevent injuries, e.g.
caused by stumbling, open
the dishwasher only briefly in
order to load and unload the
dishwasher.
■ Knives and other utensils
with sharp points must be
placed with the points
downwards in the cutlery
basket*1j or horizontally
on the knife shelf* or in the
cutlery drawer*1*.
■ Do not lean or sit on the
open door.
■ In the case of free-standing
appliances, ensure that the
baskets are not overloaded.
The appliance could tip.
■ If the appliance is not in a
cavity and a side panel is
accessible, the door hinge
area must be covered at the
side for reasons of safety
(risk of injury). The covers
are available as optional
accessories from customer
service or specialist outlets.
* depending on the features of
your dishwasher
:Warning
Risk of explosion!
Do not add any solvents to the
rinsing compartment. Danger of
explosion!
8
Page 9
Safety instructions aus
:Warning
Risk of scalding!
Open the door carefully when
the programme is still running.
There is a risk of hot water
spraying out of the appliance.
:Warning
Risk to children!
■ If fitted, use the childproof
lock.
■ Do not allow children to play
with or operate the
appliance.
■ Keep children away from
detergents and rinse aid.
These may cause chemical
burns in the mouth, throat
and eyes or asphyxiation.
■ Keep children away from
open dishwasher. There may
be small parts in the
dishwasher which children
could swallow and the water
inside the dishwasher is not
drinking water as it may
contain detergent residue.
■ Ensure that children do not
place fingers in the tablet
collecting tray 1B. Small
fingers could become caught
in the slots.
■ When opening and closing
the door on an eye-level
appliance, ensure that
children do not become
jammed or crushed between
the appliance door and the
cupboard door below.
■ Children could become
locked in the appliance
(danger of suffocation) or get
into another dangerous
situation.
Redundant appliances: Pull
out the mains plug, sever
and dispose of the power
cord. Destroy the door lock
so that the door can no
longer be closed.
Childproof lock (door lock) *
Door lock
The child-proof lock (door lock)
protects children from potential
hazards which the dishwasher
poses.
:Warning
Risk of suffocation!
Children may become locked in
the dishwasher and suffocate.
Always completely close the
appliance door when leaving
the dishwasher.
9
Page 10
aus Safety instructions
Activate the child-proof lock
(door lock) as follows:
1. Pull the catch of the
child-proof lock towards
yourself (1).
2. Close the door (2).
The child-proof lock is
activated.
Open the door with activated
child-proof lock (door lock) as
follows:
1. Press the catch of the
child-proof lock to the right
(1).
2. Open the door (2).
Deactivate the child-proof lock
(door lock) as follows:
1. Press the catch of the
child-proof lock to the right
(1).
2. Press the catch of the
child-proof lock backwards
(2).
The childproof lock is
deactivated.
* depending on the features of
your dishwasher
10
Page 11
Environmental protection aus
7 Environmental
protection
Environmental protection
Both the packaging of new appliances
and the old appliances themselves
contain valuable raw materials and
recyclable materials.
Please dispose of the individual parts
separated according to type.
Please ask your dealer or inquire at
your local authority about current means
of disposal.
Packaging
All plastic parts of the appliance are
identified with internationally
standardised abbreviations (e.g. PS
polystyrene). Therefore, plastic waste
can be sorted out when the appliance is
being disposed of.
Please follow the safety instructions
under “Delivery” ~ Page 6.
Old appliances
Please follow the safety instructions
under “Disposal of your appliance”
~ Page 8.
This appliance has been
identified in accordance with the
European Directive 2012/19/EU
on Waste Electrical and
Electronic Equipment (WEEE).
The directive provides a
framework for the collection and
recycling of old appliances,
which is valid across the EU.
* Getting to know your
appliance
Getting to know your appliance
Diagrams of the control panel and the
interior of the appliance can be found at
the front of the manual. Individual
positions are referred to in the text.
Control panel
See Fig. ~ Page 2
( On/off switch
0 Programme buttons **
8 Info button {
@ Display window at top
H Rinse aid refill indicator
P Selection buttons
X Time preselection
` Additional functions **
h START button
)" < > button
)* Open door button
)2 Front display *
* depending on the features of your
dishwasher
** number depending on the features of
your dishwasher
11
Page 12
aus Getting to know your appliance
Appliance interior
See Fig. ~ Page 2
1" Interior light *
1* Cutlery drawer *
12 Top basket
1: Upper spray arm
1B Tablet collecting tray
1J Intake opening
1R Blow opening (Zeolith container)
1Z Lower spray arm
1b Filters
1j Cutlery basket *
9" Bottom basket
9* Dispenser for rinse aid
92 Detergent dispenser
9: Lock for detergent dispenser
9B Rating plate
* depending on the features of your
dishwasher
Info button {
Info button
The Info button { can be used to
display additional programme
information.
1. Press the Info button {8.
2. Press the programme button.
Information on the selected
programme is indicated on the
display window at the top @.
3. To leave, press Info button { 8.
Time setting
Time setting
When the appliance is switched on the
for the first time, the time starts at 12:00
o’clock.
Set the time as follows:
1. Open the door.
2. Switch on ON/OFF switch (.
3. Press Info button { 8 for 3
seconds until the following text is
indicated on the display window at
the top @:
Scroll with < >
Set with - +
Leave with Setup 3 sec.
4. Keep pressing button > )" until the
time setting is indicated on the
display window at the top @.
5. Make the setting with setting buttons
+ - P. If the selection buttons + -
P are held down, the set values
are changed in 10-minute steps.
6. Press and hold the Info button {
8 for 3 seconds.
The chosen setting has now been
stored.
Note: If the appliance was
disconnected from the power supply for
a prolonged period, the time starts at
12:00 o’clock. Set the time.
12
Page 13
Getting to know your appliance aus
Switching on the appliance for the first time
When the dishwasher is switched on for
the first time, you are taken directly to
the settings for switching on the
appliance for the first time. The following
text is indicated on the display window
at the top @:
Scroll with < >
Set with - +
Leave with Setup 3 sec.
Change the setting as follows:
1. Keep pressing button > )" until the
required setting is displayed.
2. Make the setting with setting buttons
+ - P.
3. Press and hold the Info button {
8 for 3 seconds.
The chosen setting has now been
stored.
The required settings for switching on
the appliance for the first time are listed
in the table below.
Settings
Switching on the
Factory setting Infotext
by pressing Info button {
appliance for the first
time
Language English Language selection.
Time format 24h 12h or 24h.
Time setting 12:00 Set the current time.
Rinse aid disp. Setting 5 Amount of rinse aid affects drying. When
using Multitabs, select setting 0.
--------
13
Page 14
aus Getting to know your appliance
Settings
The dishwasher has been preset with
certain settings for your convenience.
You can change this factory setting.
Change the setting as follows:
1. Open the door.
2. Switch on ON/OFF switch (.
3. Press Info button { 8 for 3
seconds until the following text is
indicated on the display window at
the top @:
Scroll with < >
Set with - +
Leave with Setup 3 sec.
4. Keep pressing button > )" until the
5. Make the setting with setting buttons
+ - P.
6. Press and hold the Info button {
8 for 3 seconds.
The chosen setting has now been
stored.
You have the option of resetting all
changed settings back to the original
factory settings.
Note: When you reset your dishwasher
to the factory settings, you are taken
directly to the settings for switching on
the appliance for the first time.
required setting is displayed.
Setting Factory setting Infotext
by pressing Info button {
Time setting 12:00 Set the current time.
Time format 24h 12h or 24h.
Time display Time Show end of programme with display
"Finish in" or "Finish at".
Language English Language selection.
Rinse aid disp. Setting 5 Amount of rinse aid affects drying. When
using Multitabs, select setting 0.
Sensor setting Standard Adjustment of soiling detection for
optimum cleaning result.
Extra dry Off Improved drying for glasses and
plasticware.
Water connection * Cold water * Connection to hot water (40-60°C) or cold
water (<40°C) possible. *
Eco forecast Off Show the water and energy consumption.
Auto Power Off after 1 min. Appliance automatically switches off at
end of rinsing process.
Emotion Light * On Interior light.
Front display * On The front display can be selected.
Timelight * On While programme is running, status
information is projected onto floor.
* depending on the features of your dishwasher
14
Page 15
Getting to know your appliance aus
Setting Factory setting Infotext
by pressing Info button {
Infolight * On Light is projected to signal an active
cleaning cycle.
Start programme * Eco 45° * When switching on, the last selected
programme appears. *
Tone volume * Setting 2 Volume of signal at end of programme.
Button volume Setting 2 Volume when using buttons.
Childproof lock * Off Activated child-proof lock impedes
opening of door.
Eco drying * On Door opens automatically at the end of the
programme.
Greeting On When switching on the appliance, the
brand logo can be deselected.
Factory setting Confirm/Back Resetting to the factory setting.
* depending on the features of your dishwasher
--------
15
Page 16
aus Rinse aid
, Rinse aid
Rinse aid
As soon as the low rinse-aid indicator
H is lit on the control panel or is
requested on the front display * )2,
rinse-aid should be topped up.
The rinse aid is required for stain-free
utensils and clear glasses. Use only
rinse aid for domestic dishwashers.
Combined detergents with rinse-aid
component may be used up to a water
hardness of 21° dH (37° fH, 26°
Clarke, 3.7 mmol/l) only. If the water
hardness is over 21° dH, rinse-aid must
be used.
* depending on the features of your
dishwasher
Top up the rinse-aid as follows:
1. Open dispenser 9*; press lug on
the lid (1) and lift (2).
2. Add rinse-aid up to the max. mark.
3. Close the lid.
Lid “clicks” into position.
4. Remove overflowed rinse aid with a
cloth.
This prevents excessive frothing
during the next rinse cycle.
Setting amount of rinse aid
The amount of rinse aid to be
dispensed can be set from 0 to 6. Set
the amount of rinse aid to be dispensed
to 5 to obtain a very good drying result.
Do not change the amount of rinse aid
unless there are streaks or water stains
on the utensils. Set a lower level to
avoid streaks. Set a higher level to
avoid water stains.
Set the amount of rinse aid as follows:
1. Open the door.
2. Switch on ON/OFF switch (.
3. Press Info button { 8 for 3
seconds until the following text is
indicated on the display window at
the top @:
Scroll with < >
Set with - +
Leave with Setup 3 sec.
4. Keep pressing button > )" until the
rinse aid dispenser is indicated on
the display window at the top @.
5. Make the setting with setting buttons
+ - P.
6. Press and hold the Info button {
8 for 3 seconds.
The chosen setting has now been
stored.
16
PD[
Page 17
Utensils aus
Switching off rinse aid refill
indicator
If the use of combined detergents with a
rinse-aid component impairs the low
rinse-aid indicator H on the control
panel or the text on the front
display * )2 (enough rinse aid for x
rinse cycles), the displays can be
switched off.
Proceed as described under “Setting
amount of rinse aid” and select
setting 0.
* depending on the features of your
dishwasher
- Utensils
Utensils
Not suitable
■ Cutlery and utensils made of wood.
■ Delicate decorative glasses, craft
and antique utensils. These decors
are not dishwasher-proof.
■ Plastic parts not resistant to heat.
■ Copper and tin utensils.
■ Utensils which are soiled with ash,
wax, lubricating grease or ink.
Aluminium and silver parts have
a tendency to discolour and fade during
the wash cycle. Even some types of
glass (e.g. crystal glass objects) may
turn cloudy after many wash cycles.
Glass and utensil damage
Causes:
■ Glass type and glass production
process.
■ Chemical composition of the
detergent.
■ Water temperature of the wash
programme.
Recommendation:
■ Use only glasses and porcelain
which the manufacturer designates
as dishwasher-proof.
■ Use a detergent which protects
utensils.
■ Take glass and cutlery out of
the dishwasher as soon as possible
after the programme ends.
17
Page 18
aus Utensils
Loading the dishwasher
1. Remove large food remnants. It
is not necessary to prerinse utensils
under running water.
2. Place the utensils so that
– they are secure and cannot tip
over.
– all utensils with their openings
face down.
– parts with curves or indentations
are at an angle, thereby allowing
water to drain.
– does not obstruct rotation of the
two spray arms 1: and 1Z.
Very small utensils should not be
washed in the machine, as they may fall
out of the baskets.
Upper basket
Arrange cups and glasses in the upper
basket 12.
Note: Utensils must not be placed
above the tablet collecting tray 1B.
These may block the lid of the detergent
dispenser and prevent it from opening
fully.
Lower basket
Arrange pots and plates in the lower
basket 9".
* depending on the features of your
dishwasher
18
* depending on the features of your
dishwasher
Page 19
Utensils aus
Tip: Heavily soiled utensils (pans)
should be placed in the lower basket.
The more powerful spray jet provides a
better dishwashing result.
Tip: Other examples, such as the best
way of loading your dishwasher, can be
found on our homepage. These can be
downloaded free of charge. The
corresponding Internet address can be
found on the back page of these
instructions for use.
Cutlery basket *
Cutlery basket
Place cutlery, always unsorted with the
tips face down, in the cutlery basket *.
To prevent injuries, place long, pointed
implements and knives on the knife
shelf *.
You can take out the cutlery drawer.
Depending on the features of your
dishwasher, you can fold down the side
shelves to provide more room for taller
items of cutlery. The front rows of
prongs can be folded down to provide
room for wider handles.
* depending on the features of your
dishwasher
Cutlery drawer *
Cutlery drawer
Arrange the cutlery in the cutlery drawer
1* as illustrated. Separately arranged
utensils are easier to remove after
washing.
&/,&.
* depending on the features of your
dishwasher
19
Page 20
aus Utensils
Etagere *
Etagere
The etagere and the space underneath
can be used for small cups and glasses
or for larger items of cutlery, such as
wooden spoons or serving cutlery. If
you do not require the etagere, it can be
folded up.
&/,&.
* Depending on the features of your
dishwasher, you can adjust the etagere
3 times the height.
Adjust the height of the etagere as
follows:
1. Position the etagere vertically and
pull upwards.
2. Push etagere at a slight angle
downwards to the required height
(1, 2, or 3).
3. Engage etagere.
Etagere “clicks” into position.
Folding spikes *
Folding spikes
* Depending on the features of your
dishwasher, the spikes can be folded
down. This facilitates arrangement of
pots, bowls and glasses.
Fold down the spikes as follows:
1. Press lever forwards (1).
2. Fold down spikes (2).
Small items holder *
Small items holder
* Depending on the features of your
dishwasher, the upper basket is fitted
with small items holders. The small
items holders can be used to securely
attach light plastic parts.
20
Page 21
Utensils aus
Knife rack *
Knife rack
* Depending on the features of your
dishwasher, the upper basket is fitted
with a knife shelf. Long knives and other
utensils can be placed in the knife shelf.
Baking sheet spray head *
Baking sheet spray head
* depending on the features of your
dishwasher
Large trays or grilles as well as large
plates (gourmet plates, pasta plates,
dinner plates) can be cleaned with this
spray head.
Insert the spray head as follows:
1. Remove upper basket 12.
2. Insert spray head as illustrated and
turn to the right.
Spray head is engaged.
To ensure that the spray jet can reach
all parts, arrange the baking sheets as
illustrated (max. 2 baking sheets and 2
grilles).
Note: Ensure that the dishwasher is
always operated with upper basket 12
or baking tray spray head.
21
Page 22
aus Utensils
Unloading the dishwasher
To prevent water from dripping off the
upper basket onto the utensils in the
lower basket, it is recommended
to empty the appliance from the bottom
up.
Tip: Hot utensils are sensitive to shock!
Therefore, when the programme ends,
leave the utensils to cool down in the
dishwasher until they can be handled.
Note: When the programme ends,
water droplets can still be seen inside
the appliance. This does not affect the
drying of the utensils.
Adjusting the height of the
basket *
Adjusting the height of the basket
* depending on the features of your
dishwasher
If required, the height of the upper
basket 12 can be adjusted to create
more space for taller utensils either in
the upper or lower basket.
Appliance height 81.5 cm
With cutlery basket Upper
basket
Setting 1 max. ø 22 cm 31 cm
Setting 2 max. ø 24.5 cm 27.5 cm
Setting 3 max. ø 27 cm 25 cm
With cutlery drawer Upper
basket
Setting 1 max. ø 16 cm 31 cm
Setting 2 max. ø 18.5 cm 27.5 cm
Setting 3 max. ø 21 cm 25 cm
Appliance height 86.5 cm
With cutlery basket Upper
basket
Setting 1 max. ø 24 cm 34 cm
Setting 2 max. ø 26.5 cm 30.5 cm
Setting 3 max. ø 29 cm 28 cm
Lower
basket
Lower
basket
Lower
basket
22
With cutlery drawer Upper
basket
Setting 1 max. ø 18 cm 34 cm
Setting 2 max. ø 20.5 cm 30.5 cm
Setting 3 max. ø 23 cm 28 cm
Lower
basket
Page 23
Utensils aus
Arrange large plates up to a diameter of
31/34* cm in the lower basket 9" as
illustrated.
* depending on the features of your
dishwasher
Upper basket with side levers
1. Pull out upper basket 12.
2. Hold the sides of the basket along
the upper edge.
This prevents it from suddenly
dropping.
3. To lower the upper basket; press in
both levers on the left and right on
the outside of the basket. The upper
basket lowers.
4. To lift the upper basket; grip the
sides of the upper basket along the
upper edge and lift.
5. Ensure that both sides of the upper
basket are at the same height.
6. Push in upper basket.
Upper basket with upper and
lower pairs of rollers
1. Pull out upper basket 12.
2. Remove upper basket.
3. Re-attach upper basket to the upper
(Setting 3) or lower (Setting 1)
rollers.
4. Push in upper basket.
23
Page 24
aus Detergent
. Detergent
Detergent
You can use tablets as well as powder
or liquid detergents for dishwashers, but
never use washing up liquid. The
dosage can be individually adjusted
with powder or a liquid detergent
according to the degree of soiling.
Tablets contain an adequately large
amount of active ingredients for all
cleaning tasks. Modern, powerful
detergents predominantly use a
low-alkaline formulation with phosphate
and enzymes. Phosphates bond the
lime in the water. Enzymes break down
starch and remove protein.
Phosphate-free detergents are less
frequent. These have a slightly weaker
lime bonding capacity and require a
higher dosage. To remove coloured
stains (e.g. tea, tomato sauce),
oxygen-based bleaching agents are
usually used.
Note: To ensure a good washing result,
always follow the instructions on the
detergent packaging!
If you have further questions,
we recommend that you contact
the detergent manufacturers’ helpline.
Adding detergent
1. If the detergent dispenser 92 is still
closed, actuate locking bar 9: to
open it.
2. Pour detergent into the dry detergent
dispenser 92 only (insert tablet flat,
not on its edge).
3. Dosage: see manufacturer’s
instructions on the packaging. Use
graduated detergent dispenser.
Usually 20 ml–25 ml are adequate
for normal soiling. If using tablets,
one tablet is adequate.
PO
PO
PO
4. Close cover on the detergent
dispenser.
Cover “clicks” into position.
&/,&.
:Warning
Risk of injury and damage due to
non-observance of the safety
instructions for detergent and
rinse-aid products!
Always follow the safety instructions for
detergent products and rinse-aid
products.
24
The detergent dispenser opens
automatically at the optimum time
depending on the programme. The
powder or liquid detergent is
distributed in the appliance and is
dissolved, the tablet falls into the
tablet collecting tray where it
dissolves in doses.
Page 25
Detergent aus
Tip: If the utensils are only lightly
soiled, slightly less than the indicated
amount of detergent is usually
adequate.
Suitable detergents and care products
can be purchased online via our
website or via customer service (see
back page).
Notes
■ If programmes are short, tablets
may not have full cleaning effect
due to different dissolving properties
and there may even be undissolved
detergent residue. It is
recommended to use washing
powder for these programmes.
■ The Intensive programme (on some
models) requires one tab only. When
using washing powder, you can
apply some of this cleaning agent
to the inside of the appliance’s door.
■ If using detergents in a water-soluble
protective cover: Take hold of the
cover with dry hands only and put
the detergent into an absolutely
dry detergent dispenser only,
otherwise the detergent may stick.
■ If you switch from combined
detergents to solo detergents,
ensure that the water softening
system * and amount of rinse aid
have been set to the correct value.
* depending on the features of your
dishwasher
25
Page 26
aus Overview of programmes
/ Overview of programmes
Overview of programmes
The max. possible number of programmes is illustrated in this overview. The
corresponding programmes for your appliance can be found on the fascia. The
programme data has been measured in the laboratory according to AS/NSZ 2007.
Type of utensils
and soiling
Pots, utensils and
cutlery,
highly soiled
Utensils and
cutlery,
normally soiled
non-sensitive
utensils and
cutlery,
highly soiled
mixed utensils
and cutlery,
normally soiled
sensitive utensils,
cutlery,
temperature-sens
itive plastic and
glasses,
lightly soiled
Programme Programme data
¹
Auto 65° - 75°
Á / Ù
Auto 45° - 65°
± / °
Super 60°
â / à
Eco 45°
É / è
Auto 35° - 45°
1.) Duration: hs/mins
2.) Energy
consumption in kWh
3.) Water
consumption in
litres
4.) With Aquasensor
1.) 1:40 - 2:15
2.) 1,00 - 1,30
3.) -
4.) 11 - 15
1.) 1:30 - 2:30
2.) 0,80 - 1,30
3.) -
4.) 7 - 18
1.) 2:20
2.) 1,45
3.) 13
4.) -
1.) 2:40
2.) 0,55
3.) 12
4.) -
1.) 1:20 - 1:30
2.) 0,70 - 0,85
3.) -
4.) 10 - 15
Possible
additional
options
all
all
all
all
intensiveZone
VarioSpeed
Half load
extraDry
Shine and Dry
Programme sequence
Is optimised according
to the soiling with
the aid of sensors.
Clean 60°
Intermediate rinse
Final rinse 60°
Dry
Pre Rinse
Clean 45°
Intermediate rinse
Final rinse 35°
Dry
Is optimised according
to the soiling with
the aid of sensors.
26
Page 27
Overview of programmes aus
Type of utensils
and soiling
sensitive utensils,
cutlery,
temperature-sens
itive plastic and
glasses,
slightly adhesive,
fresh food
remnants
all types of
utensils,
lightly soiled
--------
Programme Programme data
é / è
Glass 40°
ñ / ð
Quick 45°
ù / ø
Pre Rinse
1.) Duration: hs/mins
2.) Energy
consumption in kWh
3.) Water
consumption in
litres
4.) With Aquasensor
1.) 1:40
2.) 0,85 - 0,90
3.) 14
4.) 11
1.) 0:29
2.) 0,80
3.) 10
4.) -
1.) 0:15
2.) 0,05
3.) 4
4.) -
Programme selection
You can select a suitable programme
according to the type of utensils and
type of soiling.
Possible
additional
options
intensiveZone
VarioSpeed
Half load
extraDry
Shine and Dry
Extra dry
Shine and Dry
none Pre Rinse
Programme sequence
Pre Rinse
Clean 40°
Intermediate rinse
Final rinse 50°
Dry
Clean 45°
Intermediate rinse
Final rinse 50°
Information for test institutes
Test institutes can request the
conditions for running comparison tests
by sending an e-mail to
dishwasher@test-appliances.com.
Quote the appliance number (ENr.)
and the production date (FD) which you
can find on the rating
plate 9B on the appliance door.
27
Page 28
aus Additional functions
0 Additional functions
Additional functions
* Depending on the features of your
dishwasher, you can select different
additional functions `.
Ÿ Express Wash/ Speed
Perfect/ (VarioSpeed) *
Express Wash/ Speed Perfect (VarioSpeed)
This function can reduce the running
time by approx. 20% to 50% depending
on the selected rinse programme. To
obtain optimum cleaning and drying
results at a reduced running time, water
and energy consumption are increased.
§ Half load *
Half load
If you have only a few items to wash
(e.g. glasses, cups, plates), you can
switch to “half load”. This will save
water, energy and time. It is
recommended to put a little less
detergent in the detergent dispenser
than for a full load.
μ hygienePlus
(HygienePlus) *
hygienePlus (HygienePlus)
This function increases the
temperatures and retains them for an
extra long time to obtain a defined
disinfection performance. Continuous
use of this function increases the
hygiene status. This additional option is
ideal for cleaning e.g. chopping boards
and baby bottles.
Ï intensiveZone *
intensiveZone
Perfect for a mixed load. You can wash
very soiled pots and pans in the lower
basket together with normally soiled
utensils in the upper basket. The spray
pressure in the lower basket
is intensified, the rinsing temperature
is increased slightly.
ï Shine and Dry *
Shine and Dry
By increasing the amount of water
during the rinse cycle and extending the
drying phase, stains are prevented and
the drying result is improved. There is a
slight increase in the energy
consumption. Rinse aid is
recommended for the high gloss drying
function (even when using combination
detergents).
28
Page 29
Operating the appliance aus
1 Operating the
appliance
Operating the appliance
Changing the settings
The dishwasher has been preset with
certain settings for your convenience.
You can change these factory settings.
Change the setting as follows:
1. Open the door.
2. Switch on ON/OFF switch (.
3. Press Info button {8 for 3
seconds until the following text is
indicated on the display window at
the top @:
Scroll with < >
Set with - +
Leave with Setup 3 sec.
4. Keep pressing button >)" until the
required setting is indicated on the
display window at the top @.
5. Make the setting with setting buttons
+ -P.
6. Press and hold the Info button {
8 for 3 seconds.
The chosen setting has now been
stored.
AquaSensor *
AquaSensor
* depending on the features of your
dishwasher
The Aqua sensor is an optical
measuring device (light barrier) which
measures the turbidity of the rinsing
water.
The AquaSensor is used according
to the programme. If the AquaSensor is
active, “clean” rinsing water can be
transferred to the next rinse bath and
water consumption can be reduced by
3–6 litres. If the turbidity is greater,
the water is drained and is replaced
with fresh water. In the automatic
programmes the temperature
and running time can also be adjusted
to the degree of soiling.
Tip: If you change several settings, first
make all changes in succession. Now
press the Info button { 8 for
3 seconds. This saves all set values in
the appliance.
29
Page 30
aus Operating the appliance
Zeolith drying ¼
Zeolith drying
:Warning
Risk of burns from touching the blow
opening 1R!
Never touch the blow opening. The blow
opening becomes hot and, furthermore,
any damage will result in a chargeable
callout by customer service.
Caution!
Please ensure that the intake opening
1J is not obstructed and do not place
any temperature-sensitive utensils in the
lower basket at the rear right side above
the blow opening 1R.
The appliance features a Zeolith
container. Zeolith is a mineral which can
store moisture and heat energy
and release them again.
During the washing step this heat
energy is used to dry the mineral
and heat up the rinsing water.
During the drying phase moisture from
the rinsing compartment is stored in
the mineral and heat energy
is released. This released heat energy is
blown into the rinsing compartment with
dry air. This accelerates and improves
drying.
These processes therefore save a great
deal of energy.
Time display
The running time is determined during
the programme by the water
temperature, the number of utensils as
well as the degree of soiling and may
vary (depending on the selected
programme). You can change the time
display in time or hours/minutes so that
the remaining running time of the rinsing
progamme appears in the display
window “Ready at” (for example 15:20
hours) or “Ready in” (for example 3:25).
Sensor setting
The programme sequence is optmised
in Auto programmes with the aid of
sensors. The sensors adjust the
programme strength of Auto
programmes depending on the amount
and type of soiling. You can adjust the
sensitivity of the sensors in 3 stages.
Standard: This setting is ideal for a
mixed load and heavily soiled utensils,
but also saves energy and water.
Sensitive: This setting adjusts the
programme strength for the effective
removal of food remnants, even if the
amount of soiling is low. The energy and
water consumption is adjusted
accordingly.
Very sensitive: This setting adjusts the
programme strength for difficult
conditions of use, for example firmly
dried on food remnants. This setting is
recommended if using biological or eco
detergents which contain lower
amounts of active agents. The energy
and water consumption is adjusted
accordingly.
extraDry
The final rinse uses a higher
temperature which improves the drying
result. The running time may increase
slightly. (Caution if utensils are delicate!)
You can switch the extraDry function on
or off.
Eco forecast
When Eco forecast is activated, the
average water and energy consumption
of the selected programme is briefly
displayed on the display window at the
top @.
30
Page 31
Operating the appliance aus
AutoPowerOff (Switching off
automatically after the end of
the programme)
Auto Power Off
To save energy, the dishwasher
is switched off 1 minute after
the programme ends. You can also
change this setting.
Possible settings are:
■ off: The appliance does not switch
off automatically.
■ After one minute: The appliance
switches off after 1 minute.
■ After two hours: The appliance
switches off after 2 hours.
Note: Note that for the settings "After
one minute" and "After two hours", the
interior lighting 1" is switched off. To
activate the interior lighting, press the
ON/OFF switch (.
emotionLight (interior
lighting) *
EmotionLight
* Depending on the features of your
dishwasher
EmotionLight 1" is the interior lighting
for your dishwasher. You can switch
the interior lighting on or off.
Notes
■ Depending on the setting of
AutoPowerOff, the interior lighting is
either switched on or off.
■ Note that the interior lighting is
automatically switched off after 1
hour when it is switched on and the
door is open.
TimeLight (Optical display
while the programme is
running) *
timeLight
* depending on the features of your
dishwasher
While programme is running, an optical
display (additional programme
information) is indicated on the floor
under the appliance door. If the base
panel is pulled forwards or if the
appliance is installed at eye-level with
flush furniture front, the display is not
visible.
You can switch the optical display on or
off.
Infolight *
infoLight
* depending on the features of your
dishwasher
While the programme is running, a light
spot shines on the floor under
the appliance door. Do not open the
appliance door until the light point is no
longer visible on the floor. If the
appliance door is not completely
closed, the light spot flashes *. If
the appliance is installed at eye-level,
with flush furniture front, the light point
is not visible. You can switch the
Infolight on or off.
Changing start programme *
Changing start programme
* depending on the features of your
dishwasher
You can change the “Start programme”
setting.
Front display *
Front display
* depending on the features of your
dishwasher
You can switch the front display )2 on
or off (additional programme
information).
Tone volume
The end of the programme is indicated
by a buzzer. You can also change this
setting.
31
Page 32
aus Operating the appliance
Button volume
When you are operating the dishwasher,
a signal sounds whenever a button is
pressed. You can control the volume of
the signal. If you do not like the button
volume, you can switch it off.
Child-proof lock *
Child-proof lock
* depending on the features of your
dishwasher
The dishwasher features an electronic
child-proof lock. The child-proof lock
protects children from potential hazards
which the dishwasher poses.
You can switch the child-proof lock on
or off. When the child-proof lock is on, it
is difficult to open the door.
Greeting
When you switch on the dishwasher, the
brand logo appears. You can switch off
the brand logo.
Factory setting
You can reset all settings to the factory
setting.
Switching the appliance on
1. Turn on tap fully.
2. Open the door.
3. Switch on ON/OFF switch (.
The Eco 45° programme has been
preset for environmentally friendly
operation whenever the appliance
starts. This programme remains
selected if no other programme
button 0 is pressed.
4. Press START button h.
5. Close the door.
Programme sequence starts.
Time preselection
You can delay the start of the
programme by up to 24 hours.
Depending on the setting of the time
display, the end of programme is
indicated with “Finish in” (for example
3h 25m) or “Finish at” (for example
15:20 hours).
1. Open the door.
2. Switch on ON/OFF switch (.
3. Selects programme 0.
4. Press time preselection button X.
5. Keep pressing the setting buttons + -
P until the displayed time
corresponds with your requirements.
6. Press START button h, timer
programming is activated.
7. To delete the time preselection,
press START button h for approx.
3 seconds.
Time preselection was terminated.
8. Close the door.
Programme end
* The programme has ended when
“Finished” is indicated on the display
window at the top @ and on the front
display * )2.
* The end of the programme is
displayed on the floor – provided the
TimeLight (optical display) is switched
on and is visible.
* depending on the features of your
dishwasher
32
Page 33
Operating the appliance aus
Switching off the appliance
Short time after the end of the
programme:
1. Open the door.
2. Switch off ON/OFF switch (.
3. Turn off tap (does not apply to
appliances with Aqua-Stop).
4. Remove the utensils when they have
cooled down.
Note: When the programme ends,
leave the appliance to cool down a
while before opening it. This will prevent
steam from escaping and causing
long-term damage to your built-in
furniture.
Interrupting the programme
Caution!
Expansion (overpressure) may cause
the appliance door to jump open and/or
water to escape! If the door was opened
on an appliance which has a hot water
connection or is heated, always leave
the door ajar for several minutes and
then close.
1. Open the door.
2. Switch off ON/OFF switch (.
The LEDs go out. The programme
is saved.
3. To continue the programme, switch
on the ON/OFF switch ( again.
4. Close the door.
Terminating the programme
(Reset)
Terminating the programme
1. Open the door.
2. Press the START button h and
hold for 3 seconds
The display window at the top @
and the front display * )2 show:
"Program was terminated".
3. Close the door.
The programme sequence lasts
approx. 1 min. The display window
at the top @ shows: “Finished”.
4. Open the door.
5. Switch off ON/OFF switch (.
6. Close the door.
* depending on the features of your
dishwasher
Changing the programme
When the START button h has been
pressed, the programme cannot be
changed. The only way a programme
can be changed is by Cancel
programme (Reset).
33
Page 34
aus Cleaning and maintenance
2 Cleaning and
maintenance
Cleaning and maintenance
A regular inspection and maintenance
of your machine will help to prevent
faults. This saves time and prevents
problems.
Overall condition
of the machine
■ Check rinsing compartment
for grease and limescale deposits.
If you find such deposits:
■ Fill detergent dispenser 92 with
detergent. Start the appliance
without utensils in the programme
with the highest rinsing temperature.
:Warning
Health hazard due to detergents
containing chlorine!
Always use chlorine-free detergents.
Clean the appliance with
detergents/appliance cleaners which
are particularly suitable for use with
dishwashers.
Never use a steam cleaner to clean
your dishwasher. The manufacturer
is not liable for any consequential
damage.
Regularly wipe the front
of the appliance and fascia with a damp
cloth; water and a little washing up
liquid are adequate. Do not use
sponges with a rough surface
or abrasive detergents, as these could
scratch the surfaces.
Stainless steel appliances: To prevent
corrosion, avoid using sponge cloths
or wash them out thoroughly several
times before using for the first time.
Rinse aid
As soon as the refill indicator are lit on
the fascia H or there is a request in
the display window * )2, rinse aid
should be topped up.
* depending on the features of your
dishwasher
■ To extend the life of your appliance,
clean the appliance regularly with a
special dishwasher detergent.
■ To ensure that the door seal always
remains clean and hygienic,
regularly clean it with a damp cloth
and a little washing-up liquid.
■ If the appliance is switched off for a
prolonged period, leave the door
ajar to prevent the formation of an
unpleasant odour.
34
Page 35
Cleaning and maintenance aus
Filters
The filters 1b keep large foreign
objects in the rinsing water away from
the pump. hese foreign objects may
occasionally block the filters.
The filter system consists of
■ a coarse filter
■ a flat fine filter
■ a microfilter
1. After each washing cycle check
the filters for residue.
2. Unscrew filter cylinder as illustrated
and take out filter system.
Spray arms
Limescale and contaminants in the
rinsing water may block nozzles and
bearings on the spray arms 1: and
1Z.
1. Check outlet nozzles on the spray
arms for blockages.
2. Unscrew the upper spray arm 1:
(1) and remove downwards (2).
3. Remove the lower spray arm 1Z
upwards.
3. Remove any residue and clean
filters under running water.
4. Re-install filter system in reverse
sequence and ensure that the arrow
marks are opposite each other after
closing the filter system.
4. Clean spray arms under running
water.
5. Re-engage or screw on spray arms.
35
Page 36
aus Fault, what to do?
3 Fault, what to do?
Fault, what to do?
Experience has shown that you can
rectify most faults which occur in daily
operation yourself. This ensures that the
appliance is quickly available to you
again. In the following overview you can
find possible causes of malfunctions
and helpful information for rectifying
them.
Note: If the appliance stops during
dishwashing or does not start for no
obvious reason, first run the Abort
programme function (Reset)
~ "Operating the appliance"
on page 29.
:Warning
Improper
repairs or use of non-original spare
parts may cause considerable damage
and put the user at considerable risk!
Always have repairs carried out by
technicians. If a component has to be
replaced, always use original spare
parts.
Error message
Waste water pump
Large food remnants or foreign objects
which were not captured by the filters
may block the waste water pump. The
rinsing water will then be above the
filter.
:Warning
Danger of cutting!
Sharp and pointed objects or glass
fragments may block the waste water
pump.
Always carefully remove foreign objects.
Clean the waste water pump as
follows:
1. Disconnect the dishwasher from the
power supply.
2. Take out top basket 12 and bottom
basket 9".
3. Remove the filters 1b.
4. Scoop out water, use a sponge if
required.
5. Prise off the pump cover (as shown)
using a spoon. Grip the pump cover
by the crosspiece and lift diagonally
inwards (1). Remove cover
completely.
Some faults are indicated at the top of
the display window @ and on the front
display * )2 and possible remedies
are offered (for example Filter system
soiled (E22) -->Clean filters).
* depending on the features of your
dishwasher
36
6. Check impeller wheel and remove
any foreign objects.
7. Place pump cover in the original
position (2) and press down until it
engages (3).
Page 37
Fault, what to do? aus
&/,&.
8. Install filters.
9. Re-insert baskets.
37
Page 38
aus Fault, what to do?
Fault table
Fault Cause Remedial action
Error code “:‹ˆ is lit. Intake opening (on right inside of
appliance) covered by utensils.
Error code “:‚ƒ is lit. Heating element calcified or
soiled.
Error code “:‚‰ is lit. Supply hose kinked. Install supply hose without kinks.
Tap turned off. Turn on the tap.
Tap jammed or calcified. Turn on the tap.
Filter in the water supply blocked. Switch off the appliance and pull out the
Arrange utensils so that the intake
opening is not obstructed.
Clean appliance with dishwasher cleaning
agent or descaler. Operate the dishwasher
with water softening system and check the
setting.
Flow rate must be min. 10 l/min. when
water supply is open.
mains plug. Turn off the tap. Unscrew
water connection.
Clean filter in the supply hose. Screw
water connection on again. Check for
leaks. Reconnect power supply. Switch on
the appliance.
Error code “:ƒƒ is lit. Filters 1b are soiled or
blocked.
Error code “:ƒ… is lit. Waste-water hose kinked or
blocked.
Siphon connection still sealed. Check connection to siphon and open if
Cover on the waste water pump
loose.
Error code “:ƒ† is lit. Waste water pump blocked or
cover on the waste water pump is
not locked in position.
Error code “:ƒˆ is lit. Mains voltage too low. Not an appliance fault, have the mains
38
Clean filters. ~ "Filters" on page 35
Install hose without kinks, remove any
residue.
required.
Lock cover correctly. ~ "Waste water
pump" on page 36
Clean pump and lock cover correctly.
~ "Waste water pump" on page 36
voltage and electrical installation checked.
Page 39
Fault, what to do? aus
Fault Cause Remedial action
A different error code is
indicated on the digital
display.
(“:‹‚ to “:„‹)
Refill indicator for rinse-aid
H is lit.
Refill indicator for rinse-aid
H is not lit.
Water is left in the
appliance at the end of the
programme.
Utensils not dry. No or too little rinse aid in the
A technical fault has probably
occurred.
No rinse aid. Refill rinse aid.
Refill indicator switched off. Activation/deactivation.~ "Rinse aid"
There is still enough rinse aid
available.
Filter system or area under the
filters 1b is blocked.
Program has not ended yet. Wait until programme ends or reset.
dispenser.
Programme selected without
drying.
Water collecting in depressions
on the utensils and cutlery.
Switch off appliances with the ON/OFF
switch (. After a short time restart the
appliance.
If the problem recurs, turn off the tap and
pull out the mains plug.
Call customer service and mention the
error code.
on page 16
Check refill indicator, levels.
Clean filters and area underneath.
Refill rinse aid.
Select programme with drying.
Arrange utensils in a sloping position,
arrange affected utensils as sloping as
possible.
The combined detergent used
has a poor drying performance
ExtraDry to increase drying not
activated.
Utensils were removed too early
or drying process had not ended
yet.
The eco rinse aid used has a
limited drying performance.
Plastic utensils not dry. Special properties of plastic. Plastic has a lower heat storage capacity
Use different combination detergent with
better drying performance. Use of rinse
aid also increases the drying performance.
Activate ExtraDry.
Wait until program ends or wait until 30
min after program ends before removing
utensils.
Use a proprietary rinse aid. Eco products
may have limited effectiveness.
and therefore dries less well.
39
Page 40
aus Fault, what to do?
Fault Cause Remedial action
Cutlery not dry. Cutlery not arranged properly in
Appliance interior wet after
rinse cycle.
Food remnants on the
utensils.
the cutlery basket.
Cutlery not arranged properly in
the cutlery drawer.
No appliance fault On account of the “Condensation drying”
Utensils placed too closely
together, utensils basket
overfilled.
Spray arm rotation obstructed. Arrange utensils so that the spray arm can
Spray arm nozzles are blocked. Clean the spray arm nozzles.
Filters 1b dirty. Clean filters. ~ "Cleaning and
Filters 1b inserted incorrectly
and/or not engaged.
Rinse programme too weak. Select a more intensive rinse programme.
Utensils precleaned too intensely;
sensors therefore decide on
weak programme sequence.
Stubborn soiling cannot be
completely removed.
Tall narrow receptacles in corner
areas are not rinsed adequately.
Top basket 12 on right and left
not set to same height.
Separate cutlery if possible, prevent
contact points.
Arrange cutlery properly and separate if
possible.
principle, water droplets are physically
induced and required in the container. The
humidity in the air condenses on the inner
walls of the dishwasher, drains and is
pumped out.
Arrange utensils with adequate clearance
between them ensuring that the spray jets
can reach the surface of the utensils.
Prevent contact points.
rotate without obstruction.
~ "Cleaning and maintenance"
on page 34
maintenance" on page 34
Insert and engage filters correctly.
Increase sensitivity of the sensors.
~ "Sensor setting" on page 30
Do not prerinse utensils. Remove only
large food remnants.
Increase sensitivity of the sensors.
~ "Sensor setting" on page 30
Recommended programme Intensive.
Do not place hollow receptacles too
obliquely and do not place in the corner
area.
Set top basket to same height using side
levers.
40
Page 41
Fault, what to do? aus
Fault Cause Remedial action
Detergent residue. Detergent dispenser cover 92
Water stains on plastic
parts.
Washable or water-soluble
coatings in the container or
on the door.
White, stubborn coatings;
limescale on the utensils,
container or door.
blocked by utensils and therefore
does not open fully.
Detergent dispenser cover 92
blocked by the tablet.
Tablets used in the quick or short
programme.
Dissolving time of the detergent
is not reached in the selected
short programme.
Washing effect and dissolving
performance are reduced after a
prolonged storage time or
detergent is very lumpy.
Droplet formation on plastic
surface is physically unavoidable.
After drying, water stains are
visible.
Detergent substances are
deposited. These coatings cannot
usually be removed with
chemicals (appliance cleaner, ...).
Only for glasses: Initial glass
corrosion – can only apparently
be wiped off.
Detergent substances are
deposited. These coatings cannot
usually be removed with
chemicals (appliance cleaner, ...).
Underdosing of detergent. Increase detergent dosage or change
Too weak rinse programme
selected.
Utensils must not be placed above the
tablet collecting tray 1B. These may
block the lid of the detergent dispenser
and prevent it from opening fully.
~ "Upper basket" on page 18
Do not place utensils or fragrance
dispenser in the tablet collecting tray.
Tablet must be inserted flat and not
upright.
Dissolving time of tablets too long for a
quick or short programme.
Use a detergent powder or select a more
intensive programme.
Change detergent.
Use a more intensive programme (more
water changes).
Arrange utensils in a sloping position.
Use rinse aid.
Change detergent brand.
Clean appliance mechanically.
See “Glass and utensil damage”
~ Page 17.
Change detergent brand.
Clean appliance mechanically.
detergent.
Select a more intensive rinse programme.
41
Page 42
aus Fault, what to do?
Fault Cause Remedial action
Tea or lipstick residue on
the utensils.
Coloured (blue, yellow,
brown), difficult to remove
to non-removable coatings
in the appliance or on
stainless steel utensils.
Discolouration of the
plastic parts inside the
appliance.
Plastic parts discoloured. Too low rinsing temperature. Select programme with higher washing
Removable streaks on
glasses, glasses with
metallic appearance and
cutlery.
Too low rinsing temperature. Select programme with higher washing
Too little or unsuitable detergent. Use suitable detergent at correct dosage.
Utensils precleaned too intensely;
sensors therefore decide on
weak programme sequence.
Stubborn soiling cannot be
completely removed.
Film formation consisting of
ingredients from vegetables (e.g.
cabbage, celery, potatoes,
noodles, ...) or the tap water (e.g.
manganese).
Film formation caused by metallic
components on silver or
aluminium utensils.
Plastic parts inside the appliance
may become discoloured during
the service life of the dishwasher.
Utensils precleaned too intensely;
sensors therefore decide on
weak programme sequence.
Stubborn soiling cannot be
completely removed.
Too much rinse aid. Set rinse aid amount to lower setting.
No rinse aid added or setting too
low.
Detergent residue in the final
rinse programme section.
Detergent dispenser cover
blocked by utensils (cover does
not open fully).
Utensils precleaned too intensely;
sensors therefore decide on
weak programme sequence.
Stubborn soiling cannot be
completely removed.
temperature.
Do not prerinse utensils. Remove only
large food remnants.
Increase sensitivity of the sensors.
~ "Sensor setting" on page 30
Can be partly removed with machine
cleaner or by mechanical cleaning.
Coatings are harmless.
Can be partly removed with machine
cleaner or by mechanical cleaning.
Discolouration is normal and will not
impair the function of the dishwasher.
temperature.
Do not prerinse utensils. Remove only
large food remnants.
Increase sensitivity of the sensors.
~ "Sensor setting" on page 30
Add rinse aid and check dosage
(recommended setting 4–5).
Detergent dispenser cover must not be
obstructed by utensils.
Do not place utensils or fragrance
dispenser in the tablet collecting tray.
Do not prerinse utensils. Remove only
large food remnants.
Increase sensitivity of the sensors.
~ "Sensor setting" on page 30
42
Page 43
Fault, what to do? aus
Fault Cause Remedial action
Initial or existing,
irreversible clouding of
glass.
Rust spots on the cutlery. Cutlery not adequately
Appliance cannot be
switched on or operated.
Appliance does not start. The mains fuse has tripped. Check mains fuse.
Programme starts
automatically.
The door is difficult to
open.
Door cannot be closed. Door lock has been activated. Close door with increased force.
Cover on the detergent
dispenser cannot be
closed.
Detergent residue in the
detergent dispenser 92
or in the tablet collecting
tray 1B.
Glasses not dishwasher-proof,
only suitable for dishwasher.
rust-resistant. Knife blades are
frequently more severely
affected.
Cutlery will also rust if rusting
parts are rinsed at the same time
(pan handles, damaged utensil
baskets, etc.).
Malfunction. Disconnect appliance from the power
Power cord not inserted. Ensure that the power cord is plugged all
The appliance door has not been
shut properly.
You did not wait until programme
ended.
Child lock is activated. Deactivate the child lock.
Door cannot be closed due to
installation.
Detergent dispenser or cover
guide blocked by sticky detergent
residue.
Spray arms blocked by utensils,
therefore detergent is not rinsed
out.
The detergent dispenser was
damp when filled.
Use dishwasher-proof glasses.
Avoid long steam phase (standing time
after wash cycle ends).
Use wash cycle at lower temperature.
Use detergent with glass protection
component.
Use corrosion-resistant cutlery.
Do not wash rusting parts.
supply; pull out the mains plug or switch
off the fuse. Wait at least 5 seconds, then
connect the appliance to the power
supply.
the way into the back of the appliance and
into the socket. Check that the socket
functions.
Close the door.
Perform reset.
Check appliance installation: Door
or attached parts must close without
obstruction.
Remove detergent residue.
Ensure that the spray arms can rotate
freely.
Pour detergent into the dry detergent
dispenser only.
43
Page 44
aus Fault, what to do?
Fault Cause Remedial action
Appliance stops in the
programme or programme
is interrupted.
Door not closed properly. Close the door.
Do not place utensils or fragrance
dispenser in the tablet collecting
tray.
Check whether rear panel is being
pressed in, e.g. by socket or by hose
holder which has not been removed.
Top basket presses against the
door and prevents door from
being closed securely.
Power and/or water supply
Restore power and/or water supply.
interrupted.
Filling valves making
striking noises.
Depends on domestic installation,
as appliance is not defective. No
No remedial action possible.
effect on appliance function.
Knocking or rattling noise. Spray arm strikes the utensils,
utensils not positioned correctly.
If there is a low load, the water
jets strike the washing tank
directly.
Light utensils move during the
Position utensils so that the spray arms do
not strike the utensils.
Load the appliance with more utensils or
distribute the utensils more evenly in the
dishwasher.
Arrange light utensils securely.
wash cycle.
Unusual foam formation. Handwash liquid in the rinse aid
dispenser.
Immediately refill rinse aid dispenser with
rinse aid.
Rinse aid spilled. Remove rinse aid with a cloth.
--------
44
Page 45
Customer service aus
4 Customer service
Customer service
If you are unable to rectify the fault,
please contact your customer service.
We will always find an appropriate
solution in order to avoid unnecessary
visits by engineers. Contact information
for your nearest customer service can
be found on the back of these
instructions for use or on the enclosed
customer service list. When calling,
please state the appliance number
(E-Nr. = 1) and the production number
(FD = 2) which can be found on the
rating plate 9B on the appliance door.
(1U
)'
(1U
Trust the expertise of the
manufacturer. Contact us for
assistance. You can therefore be sure
that the repair is carried out by trained
service technicians who carry original
spare parts for your domestic
appliances.
* depending on the features of your
dishwasher
)'
5 Installation and
connection
Installation and connection
The dishwasher must be connected
correctly, otherwise it will not function
properly. The specifications for the inlet
and outlet as well as the electrical
connected loads must correspond with
the required criteria as
specified in the following paragraphs
or in the installation instructions.
Install the appliance in the correct
sequence:
1. Checking appliance on delivery
2. Installation
3. Drainage connection
4. Drinking water connection
5. Electrical connection
Contents of package
If you have any complaints, contact the
dealer from whom you purchased the
appliance or our customer services.
■ Dishwasher
■ User manual
■ Installation instructions
■ Quick reference guide*
■ Warranty*
■ Installation materials
■ Steam guard plate*
■ Rubber apron*
■ Power cord
* depending on the features of your
dishwasher
Safety instructions
Please follow the safety instructions
under ~ "Installation" on page 6.
45
Page 46
aus Installation and connection
Delivery
Your dishwasher has been checked
thoroughly in the factory to ensure that
it is in working order. This may cause
small water stains. These will disappear
after the first wash cycle.
Technical specifications
■ Weight:
up to 60 kg
■ Voltage:
220–240 V, 50 Hz or 60 Hz
■ Connected load:
2.0 - 2.4 kW.
■ Fuse:
10/16 A (UK 13 A).
■ Power input:
off mode (Po)* 0,50 W.
left on mode (Pl)* 50 W.
*according to regulations (EU) nos.
1016/2010 and 1059/2010.
Additional functions and settings
may increase the power input.
■ Water pressure:
at least 0.05 MPa (0.5 bar),
maximum 1 MPa (10 bar).
At a higher water pressure:
connect pressure-reducing valve
ahead.
■ Inlet rate:
minimum 10 litres/minute
■ Water temperature:
cold water.
Hot water:
Maximum temperature 60 °C.
■ Capacity:
12–15 place settings (depending on
the features of your dishwasher).
Installation
The required installation dimensions
can be found in the installation
instructions. Level the appliance with
the aid of the height-adjustable feet.
Ensure that the appliance is situated
securely on the floor.
■ A built-under or integrated appliance
which is installed subsequently as a
free-standing appliance must be
secured to prevent it from
overturning, e.g. by screwing it to the
wall or by installing it under a
continuous worktop which is
screwed to adjacent cupboards.
■ The appliance can easily be installed
in a fitted kitchen between wooden
and plastic walls.
Drainage connection
1. The required work sequence can be
found in the installation instructions.
If required, fit a siphon with an
drainage connection.
2. Connect the waste-water hose
to the drainage
connection of the siphon with
the enclosed parts.
Ensure that the drainage hose is not
kinked, crushed or twisted and that
there is no cover
plate in the drainage to prevent
the waste water from flowing out!
46
Page 47
Installation and connection aus
Drinking water connection
1. Fasten the drinking water connection
to the tap according
to the installation instructions using
the enclosed parts.
Ensure that the drinking water
connection is not kinked, crushed
or twisted.
2. When replacing the appliance,
always use a new water supply
hose.
Water pressure:
at least 0.05 MPa (0.5 bar), maximum 1
MPa (10 bar).
At a higher water pressure:
connect pressure-reducing valve ahead.
Inlet rate:
minimum 10 litres/minute
Water temperature:
cold water.
Hot water:
Maximum temperature 60 °C.
Warm water connection *
Warm water connection
* depending on the features of your
dishwasher
The dishwasher can be connected
to cold or hot water up to max. 60 °C.
Connection to hot water is
recommended if the hot water can be
supplied by energetically favourable
means and from a suitable installation,
e.g. solar heating system with
circulation line. This will save energy
and time. The “Hot water” setting allows
you to adjust your dishwasher optimally
to operation with hot water. It is
recommended to have a water
temperature (temperature of the
incoming water) of at least 40 °C and
no more than 60 °C. It is not
recommended to connect the appliance
to hot water if the water is supplied from
an electric boiler.
To change the setting:
1. Open the door.
2. Switch on ON/OFF switch (.
3. Press Info button {8 for 3
seconds until the following text is
indicated on the display window at
the top @:
Scroll with < >
Set with - +
Leave with Setup 3 sec.
4. Keep pressing the button > )" until
water connection appears of the
display window at the top @.
5. Make the setting with setting buttons
+ -P.
6. Press and hold the Info button {
8 for 3 seconds.
The chosen setting has now been
stored.
47
Page 48
aus Installation and connection
Electrical connection
■ Connect the appliance to an
alternating current only, ranging from
220 V to 240 V and 50 Hz or 60 Hz
via a correctly installed socket with
protective earth conductor. See
rating plate for required fusing 9B.
■ The socket must be near the
appliance and freely accessible
following installation.
If the plug is not freely accessible, an
allpole disconnector with a contact
opening of at least 3 mm must be
fitted on the installation side to
satisfy the relevant safety
instructions.
■ The connection may be modified
by technicians only.
■ A power cord extension may be
purchased from customer service
only.
■ Use only a residual current operated
circuit-breaker which features the
symbol ‚. Only this extension
guarantees compliance with
the currently valid regulations.
■ The appliance features a water
damage protection system. Please
note the system will function only
when the power supply
is connected.
Removal
Also observe
the sequence of worksteps here.
1. Disconnect the appliance from the
power supply.
2. Turn off the tap.
3. Undo the waste water and drinking
water connection.
4. Loosen fastening screws for the
furniture parts.
5. If fitted, remove the base panel.
6. Pull out the appliance, carefully
pulling the hose behind.
48
Page 49
Installation and connection aus
Transporting
Empty the dishwasher and secure loose
parts.
Drain the appliance according
to the following steps:
1. Turn on the tap.
2. Open the door.
3. Switch on ON/OFF switch (.
4. Select programme with the highest
temperature.
The estimated programme duration
is indicated on the display window at
the top @.
5. Press START button h.
6. Close the door.
Programme sequence starts.
7. Open the door after
approx. 4 minutes.
8. Press START button h until
“Program was terminated”/“Ready in
one minute.” is indicated at the top
of the display window @.
9. Close the door.
10. Open the door after approx. 1
minute.
The display window at the top @
indicates; “Finished”.
11. Switch off ON/OFF switch (.
12. Turn off the tap, disconnect supply
hose and drain water.
Protection against frost
Protection against frost (Emptying the appliance)
If the appliance is in a room where there
is a risk of frost (e.g. holiday home),
empty the appliance completely (see
Transportation).
Note: Transport appliance upright only.
This prevents residual water from
running into the machine control
and damaging the programme
sequence.
6XEMHFWWRFKDQJHV
49
Page 50
$TXD6WRSJXDUDQWHH
*OBEEJUJPOUPXBSSBOUZDMBJNTBHBJOTUUIFTFMMFSCBTFEPOUIFQVSDIBTFDPOUSBDU
BOEJOBEEJUJPOUPPVSBQQMJBODFXBSSBOUZXFXJMMQBZEBNBHFTVOEFS
UIFGPMMPXJOHDPOEJUJPOT
*GPVS"RVB4UPQTZTUFNJTEFGFDUJWFBOEDBVTFTXBUFSEBNBHF
XFXJMMNBLFHPPEUIFEBNBHFGPSQSJWBUFVTFST
5PFOTVSFXBUFSEBNBHFQSPUFDUJPOUIFBQQMJBODFNVTUCFDPOOFDUFE
UPUIFQPXFSTVQQMZ
5IJTMJBCJMJUZHVBSBOUFFJTWBMJEGPSUIFTFSWJDFMJGFPGUIFBQQMJBODF
"QSFSFRVJTJUFGPSUIFXBSSBOUZDMBJNJTUIBUUIFBQQMJBODFIBTCFFODPSSFDUMZ
JOTUBMMFEBOEDPOOFDUFEXJUI"RVB4UPQBDDPSEJOHUPPVSJOTUSVDUJPOT
5IJTBMTPJODMVEFTUIFDPSSFDUJOTUBMMBUJPOPGUIF"RVB4UPQFYUFOTJPO
PSJHJOBMBDDFTTPSZ0VSXBSSBOUZEPFTOPUFYUFOEUPEFGFDUJWF
GFFEMJOFTPSGJUUJOHTVQUPUIF"RVB4UPQDPOOFDUJPOPOUIFUBQ
*GZPVSBQQMJBODFJTGJUUFEXJUI"RVB4UPQZPVDBOMFBWFZPVSBQQMJBODF
VOBUUFOEFEEVSJOHPQFSBUJPOBOEMFBWFUIFUBQUVSOFEPOBGUFSXBSET
5IFUBQTIPVMEPOMZCFUVSOFEPGGJGZPVBSFBCTFOUGSPNIPNFGPS
BQSPMPOHFEQFSJPEFHTFWFSBMXFFLTIPMJEBZ
EPFTOPUBQQMZUPBQQMJBODFTXJUIPVU"RVB4UPQ
5HSDLURUGHUDQGDGYLFHRQIDXOWV
(#
*&
64
$POUBDUJOGPSNBUJPOGPSBMMDPVOUSJFTDBOCFGPVOEPOUIFFODMPTFEDVTUPNFSTFSWJDFMJTU
$BMMTGSPNB#5MBOEMJOFXJMMCFDIBSHFEBUVQUPQFODFQFSNJOVUF
"DBMMTFUVQGFFPGVQUPQFODFNBZBQQMZ
ƉQFSNJOVUFBUQFBL0GGQFBLƉQFSNJOVUF
UPMMGSFF
5REHUW%RVFK+DXVJHUlWH*PE+
$BSM8FSZ4USBF
.ßODIFO
(FSNBOZ
ZZZERVFKKRPHFRP
*9001184842*
9001184842
(9603) 642 TW
Loading...