the home and only for its
designated purpose: for
washing domestic dishes.
■ This appliance is intended
for use up to a maximum
altitude of 2500 metres
above sea level.
( Safety instructions
Safety instructions
This appliance may be used by
children over the age of 8 years
old and by persons with
reduced physical, sensory or
mental capabilities or by
persons with a lack of
experience or knowledge if they
are supervised or are instructed
by a person responsible for
their safety how to use the
appliance safely and have
understood the associated
hazards.
Children must not play with, on,
or around the appliance.
Children must not clean the
appliance or carry out general
maintenance unless they are at
least 8 years old and are being
supervised.
Keep children below the age of
8 years old at a safe distance
from the appliance and power
cable.
Before you switch ON the
appliance
Please read the instructions for
use and installation carefully.
They contain important
information on how to install,
use and maintain the appliance.
Retain all documents for later
use or for the subsequent
owner.
You can download the
instructions for use from our
website free of charge. The
relevant Internet address can
be found overleaf on these
instructions for use.
Delivery
1. Check the packaging and
dishwasher immediately for
damage caused in transit.
Do not switch on a damaged
appliance, but contact your
supplier.
2. Please dispose of the
packaging material in an
environmentally friendly
manner.
3. Do not let children play with
packaging and its parts.
There is a risk of suffocation
from collapsible boxes and
film.
5
en Safety instructions
Installation
■ Following installation, ensure
that the back of the
dishwasher is not freely
accessible (protection
against contact due to hot
surface).
■ Install and connect the
appliance according to the
installation and assembly
instructions.
■ Prior to installation,
disconnect the dishwasher
from the power supply.
■ Ensure that the protective
conductor system of the
domestic supply has been
correctly installed.
■ The electrical connection
conditions must correspond
with the specifications on the
dishwasher rating plate 9J.
■ If the power cord of this
appliance is damaged, it
must be replaced with a
particular power cord.
To prevent injury, the power
cord may be purchased from
customer service only.
■ If the dishwasher is installed
in a high-sided unit, the unit
must be secured properly.
■ If the dishwasher is installed
below or above other
domestic appliances, follow
the information for
installation in combination
with a dishwasher in the
installation instructions for
the particular appliances.
■ Also follow the installation
instructions for the
dishwasher to ensure that all
appliances are operated
safely.
■ If there is no information or if
the installation instructions
do not include the
appropriate information,
contact the manufacturer of
these appliances to ensure
that the dishwasher can be
installed above or below
these appliances.
■ If you cannot obtain any
information from the
manufacturer, you must not
install the dishwasher above
or below these appliances.
■ If you install a microwave
oven above the dishwasher,
the microwave oven may be
damaged.
■ Install built-under or
integratable appliances only
under continuous worktops
which have been screwed to
adjacent cupboards to
ensure stability.
■ Do not install the appliance
near heat sources (radiators,
heat storage tanks, cookers
or other appliances which
generate heat) and do not
install under a hob.
6
Safety instructions en
■ Please note that the
insulation material of the
dishwasher power cord may
melt next to heat sources
(e.g. heating / hot water
installations) or hot
appliance parts. Make sure
that the power cord of the
dishwasher never comes into
contact with heat sources or
hot appliance parts.
■ After installing the appliance,
ensure that the plug is easily
accessible. ~ "Electrical
connection" on page 52
■ For some models:
The plastic housing on the
water connection contains an
electric valve. The supply
hose contains electrical
connection cables. Do not
cut through the supply hose.
Do not immerse the plastic
housing in water.
In daily use
Read and observe the safety
information and instructions for
use on the packaging for
cleaning and rinsing agents.
Damage
■ The appliance may be
repaired and opened up by a
technician only. To do this,
disconnect the appliance
from the power supply. Pull
out the mains plug or switch
off the fuse. Turn off the tap.
■ If the appliance is damaged,
especially the control panel
(cracks, holes, broken
buttons), or the door function
is impaired, stop operating
the appliance. Pull out the
mains plug or switch off the
fuse. Turn off tap, call
customer service.
Disposal
1. Make redundant appliances
unusable to prevent
subsequent accidents.
2. Dispose of the appliance in
an environmentally friendly
manner.
7
en Safety instructions
:Warning
Risk of injury!
■ To prevent injuries, e.g.
caused by stumbling, open
the dishwasher only briefly in
order to load and unload the
dishwasher.
■ Knives and other utensils
with sharp points must be
placed with the points
downwards in the cutlery
basket*9" or horizontally
on the knife shelf* or in the
cutlery drawer*1*.
■ Do not lean or sit on the
open door.
■ In the case of free-standing
appliances, ensure that the
baskets are not overloaded.
The appliance could tip.
■ If the appliance is not in a
cavity and a side panel is
accessible, the door hinge
area must be covered at the
side for reasons of safety
(risk of injury). The covers
are available as optional
accessories from customer
service or specialist outlets.
* depending on the features of
your dishwasher
:Warning
Risk of explosion!
Do not add any solvents to the
rinsing compartment. Danger of
explosion!
:Warning
Risk of scalding!
Open the door carefully when
the programme is still running.
There is a risk of hot water
spraying out of the appliance.
:Warning
Risk to children!
■ If fitted, use the childproof
lock.
■ Do not allow children to play
with or operate the
appliance.
■ Keep children away from
detergents and rinse aid.
These may cause chemical
burns in the mouth, throat
and eyes or asphyxiation.
■ Keep children away from
open dishwasher. There may
be small parts in the
dishwasher which children
could swallow and the water
inside the dishwasher is not
drinking water as it may
contain detergent residue.
8
Safety instructions en
■ Ensure that children do not
place fingers in the tablet
collecting tray 1B. Small
fingers could become caught
in the slots.
■ When opening and closing
the door on an eye-level
appliance, ensure that
children do not become
jammed or crushed between
the appliance door and the
cupboard door below.
■ Children could become
locked in the appliance
(danger of suffocation) or get
into another dangerous
situation.
Redundant appliances: Pull
out the mains plug, sever
and dispose of the power
cord. Destroy the door lock
so that the door can no
longer be closed.
Childproof lock (door lock) *
Doo r lock
The child-proof lock (door lock)
protects children from potential
hazards which the dishwasher
poses.
:Warning
Risk of suffocation!
Children may become locked in
the dishwasher and suffocate.
Always completely close the
appliance door when leaving
the dishwasher.
Activate the child-proof lock
(door lock) as follows:
1. Pull the catch of the
child-proof lock towards
yourself (1).
2. Close the door (2).
The child-proof lock is
activated.
Open the door with activated
child-proof lock (door lock) as
follows:
1. Press the catch of the
child-proof lock to the right
(1).
2. Open the door (2).
9
en Environmental protection
Deactivate the child-proof lock
(door lock) as follows:
1. Press the catch of the
child-proof lock to the right
(1).
2. Press the catch of the
child-proof lock backwards
(2).
The childproof lock is
deactivated.
* depending on the features of
your dishwasher
7 Environmental
protection
Envi r o nment al prot ect i on
Both the packaging of new appliances
and the old appliances themselves
contain valuable raw materials and
recyclable materials.
Please dispose of the individual parts
separated according to type.
Please ask your dealer or inquire at
your local authority about current means
of disposal.
Packaging
All plastic parts of the appliance are
identified with internationally
standardised abbreviations (e.g. PS
polystyrene). Therefore, plastic waste
can be sorted out when the appliance is
being disposed of.
Please follow the safety instructions
under “Delivery” ~ Page 5.
Old appliances
Please follow the safety instructions
under “Disposal of your appliance”
~ Page 7.
This appliance has been
identified in accordance with the
European Directive 2012/19/EU
on Waste Electrical and
Electronic Equipment (WEEE).
The directive provides a
framework for the collection and
recycling of old appliances,
which is valid across the EU.
10
Getting to know your appliance en
* Getting to know your
appliance
Gett i ng to know your appl ianc e
Diagrams of the control panel and the
interior of the appliance can be found at
the front of the manual. Individual
positions are referred to in the text.
Control panel
See Fig. ~ Page 2
(On/off switch
0Programme buttons **
8Info button {
@Display window at top
HRinse aid refill indicator
PSalt refill indicator
XSelection buttons
`Time preselection
hAdditional functions/programme
** number depending on the features of
your dishwasher
Appliance interior
See Fig. ~ Page 2
1" Interior light *
1* Cutlery drawer *
12 Top basket
1: Upper spray arm
1B Tablet collecting tray
1J Intake opening
1R Blow opening (Zeolith container)
1Z Lower spray arm
1b Dispenser for special salt
1j Filters
9" Cutlery basket *
9* Bottom basket
92 Dispenser for rinse aid
9: Detergent dispenser
9B Lock for detergent dispenser
9J Rating plate
* depending on the features of your
dishwasher
11
en Getting to know your appliance
Info button {
Info but ton
The Info button { can be used to
display additional programme
information.
1. Press the Info button {8.
2. Press the programme button.
Information on the selected
programme is indicated on the
display window at the top @.
3. To leave, press Info button {8.
Time setting
Ti me sett ing
When the appliance is switched on the
for the first time, the time starts at 12:00
o’clock.
Set the time as follows:
1. Open the door.
2. Switch on ON/OFF switch (.
3. Press Info button {8 for 3
seconds until the following text is
indicated on the display window at
the top @:
Scroll with < >
Set with - +
Leave with Setup 3 sec.
4. Keep pressing button > )* until the
time setting is indicated on the
display window at the top @.
5. Make the setting with setting buttons
+ - X. If the selection buttons + -
X are held down, the set values
are changed in 10-minute steps.
6. Press and hold the Info button {
8 for 3 seconds.
The chosen setting has now been
stored.
Note: If the appliance was
disconnected from the power supply for
a prolonged period, the time starts at
12:00 o’clock. Set the time.
12
Getting to know your appliance en
Switching on the appliance for the first time
When the dishwasher is switched on for
the first time, you are taken directly to
the settings for switching on the
appliance for the first time. The following
text is indicated on the display window
at the top @:
Scroll with < >
Set with - +
Leave with Setup 3 sec.
Change the setting as follows:
1. Keep pressing button > )* until the
required setting is displayed.
2. Make the setting with setting buttons
+ - X.
3. Press and hold the Info button {
8 for 3 seconds.
The chosen setting has now been
stored.
The required settings for switching on
the appliance for the first time are listed
in the table below.
Settings
Switching on the
Factory settingInfotext
by pressing Info button {
appliance for the first
time
LanguageDeutschLanguage selection.
Time format24h12h or 24h.
Time setting12:00Set the current time.
Water hardness°E 16 - 20 mediumSetting water hardness. When using
Multitabs, select the lowest setting.
Rinse aid disp.Setting 5Amount of rinse aid affects drying. When
using Multitabs, select setting 0.
Water connection *Cold waterConnection to hot water (40-60°C) or cold
water (<40°C) possible.
* depending on the features of your dishwasher
--------
13
en Getting to know your appliance
Settings
The dishwasher has been preset with
certain settings for your convenience.
You can change this factory setting.
Change the setting as follows:
1. Open the door.
2. Switch on ON/OFF switch (.
3. Press Info button {8 for 3
seconds until the following text is
indicated on the display window at
the top @:
Scroll with < >
Set with - +
Leave with Setup 3 sec.
4. Keep pressing button > )* until the
5. Make the setting with setting buttons
+ - X.
6. Press and hold the Info button {
8 for 3 seconds.
The chosen setting has now been
stored.
You have the option of resetting all
changed settings back to the original
factory settings.
Note: When you reset your dishwasher
to the factory settings, you are taken
directly to the settings for switching on
the appliance for the first time.
required setting is displayed.
SettingFactory settingInfotext
by pressing Info button {
Time setting12:00Set the current time.
Time format24h12h or 24h.
Time displayTimeShow end of programme with display
"Finish in" or "Finish at".
LanguageDeutschLanguage selection.
Water hardness°E 16 - 20 mediumSetting water hardness. When using
Multitabs, select the lowest setting.
Rinse aid disp.Setting 5Amount of rinse aid affects drying. When
using Multitabs, select setting 0.
Sensor settingStandardAdjustment of soiling detection for
optimum cleaning result.
Extra dryOffImproved drying for glasses and
plasticware.
Water connection *Cold waterConnection to hot water (40-60°C) or cold
water (<40°C) possible.
Eco forecastOffShow the water and energy consumption.
Auto Power Offafter 1 min.Appliance automatically switches off at
end of rinsing process.
Emotion Light *OnInterior light.
Front display *OnThe front display can be selected.
* depending on the features of your dishwasher
14
Water softening system/special salt en
SettingFactory settingInfotext
by pressing Info button {
Timelight *OnWhile programme is running, status
information is projected onto floor.
Infolight *OnLight is projected to signal an active
cleaning cycle.
Start programmeEco 50°When switching on, the last selected
programme appears.
Tone volume *Setting 2Volume of signal at end of programme.
Eco drying *OnDoor opens automatically at the end of the
programme.
GreetingOnWhen switching on the appliance, the
brand logo can be deselected.
Factory settingConfirm/BackResetting to the factory setting.
* depending on the features of your dishwasher
--------
+ Water softening
system / special salt
Wat er sof t ening syst em/special sal t
To ensure good rinsing results, the
dishwasher requires soft water, i.e.
water which is low in lime, otherwise
limescale will be deposited on the
utensils and interior container. Tap
water above 7° dH (1.2 mmol/l) must
be softened. The water is softened with
special salt (regeneration salt) in the
water softening system
of the dishwasher. The setting and
therefore the required amount of salt
depends on the degree of hardness of
your tap water (see following water
hardness table).
Water hardness table
:DWHU
KDUGQHVV
YDOXH(
Ȣ
Ȣ
Ȣ
Ȣ
Ȣ
Ȣ
Ȣ
Ȣ
+DUGQHVV
UDQJH
VRIW
VRIW
PHGLXP
PHGLXP
PHGLXP
KDUG
KDUG
KDUG
PPROO
Ȣ
Ȣ
Ȣ
Ȣ
Ȣ
Ȣ
Ȣ
Ȣ
6HWYDOXH
RQWKH
PDFKLQH
15
en Water softening system/special salt
Adjusting the water softening
system
The amount of salt dispensed can be
set from 0 to 62°E. Salt is not required
at the set value 0-8.
Set the softening system as follows:
1. Ask your local water utility company
for the water hardness value of the
tap water.
2. Required setting can be found in the
water hardness table.
3. Open the door.
4. Switch on ON/OFF switch (.
5. Press Info button {8 for 3
seconds until the following text is
indicated on the display window at
the top @:
Scroll with < >
Set with - +
Leave with Setup 3 sec.
6. Keep pressing button > )* until the
water hardness is indicated on the
display window at the top @.
7. Make the setting with setting buttons
+ - X.
8. Press and hold the Info button {
8 for 3 seconds.
The chosen setting has now been
stored.
Using special salt
As soon as the low salt indicator P is
lit on the control panel or is requested
on the front display * ):, salt should
be topped up. Always refill with special
salt immediately before switching on the
appliance. This ensures that overrun
special salt solution is immediately
washed out and does not corrode
the rinsing tank.
Caution!
Detergent will destroy the water
softening system! Never pour detergent
into the salt dispenser.
Top up the salt as follows:
1. Undo the screw plug on the
dispenser 1b.
2. Fill the dispenser with water
(required only when switching on the
appliance for the first time).
3. Add salt as illustrated (do not use
table salt or tablets).
The water is displaced and runs out.
16
* depending on the features of your
dishwasher
Rinse aid en
Using detergents with salt
component
Deter gent wi t h a salt component
If combined detergents with a salt
component are used, special salt can
usually be omitted up to a water
hardness of 21° dH (37° fH,
26° Clarke, 3.7 mmol/l). If the water
hardness is over 21° dH, salt must be
used.
Switching off low salt
indicator / water softening
system
Swi t c h i ng of f wat e r soft ening system
If the use of combined detergents with
a salt component impairs the low salt
indicator P on the control panel or
the text on the display window at the
top @ (enough salt for x rinse cycles),
the displays can be switched off.
Proceed as described under “Setting
water softening system” and set the
value to 0-8. The water softening system
and salt refill indicator are now switched
off.
, Rinse aid
Ri n se ai d
As soon as the low rinse-aid indicator
H is lit on the control panel or is
requested on the front display * ):,
rinse-aid should be topped up.
The rinse aid is required for stain-free
utensils and clear glasses. Use only
rinse aid for domestic dishwashers.
Combined detergents with rinse-aid
component may be used up to a water
hardness of 21° dH (37° fH, 26°
Clarke, 3.7 mmol/l) only. If the water
hardness is over 21° dH, rinse-aid must
be used.
* depending on the features of your
dishwasher
Top up the rinse-aid as follows:
1. Open dispenser 92; press lug on
the lid (1) and lift (2).
17
Loading...
+ 37 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.