Bosch SMS69T08EU User Manual

Start

h : min.

Filling the salt dispenser

Adding rinse aid

Adding detergent

Select programme

Brief and handy: everything your dishwasher needs …

Before using for the first time, read the Installation instructions and Operating instructions!

Summary of instructions Dishwasher

Switching on the appliance

Switch off the appliance

Everything o.k....

Start programme

Here we go...

Ask your water supply company what the water hardness is and enter...

Adjusting the water softening system*

Quickly sorted ...

* only before the first wash or if the water hardness has been changed

How to adjust

h : min.

– Switch on ON/OFF switch.

– Hold down programme buttonA and press START button until H:0... is indicated on the digital display.

– Release both buttons. The LED for button A flashes and the factory set value of H:04 is indicated on the digital display.

– Press programme buttonC. Each time the button is pressed the set value increases by one setting; when the value reaches H:07, the display jumps back toH:00 (off).

– Press START button. The chosen setting has now been stored.

• ‹‹

• ‹‚

• ‹ƒ

• ‹„

• ‹…

• ‹†

• ‹‡

• ‹ˆ

: : : : : : : :

0-8

9-10 11-12 13-15 16-20 21-26 27-38 39-62

0 -1.1

1.2-1.4

1.5-1.8

1.9-2.1

2.2-2.9

3.0-3.7

3.8-5.4

5.5-8.9

Water hardness value °Clarke

Hardness range

mmol/l

Factory setting

soft

medium

hard

Dissolves limescale (not necessary for set value 0!) ...

Unscrew cover.

Fill the salt dispenser with water before the first wash only.

Add special salt (never add detergent!).

Screw on the cover. Wash immediately.

Spick and span ...

Press mark 1, lift up cover 2.

Fill in rinse aid.

Screw on the cover. CLICK!

A lot of dirt, a lot of detergent ...

If required, open the cover (press button).

Attention:

Combination products are not suitable for all programmes, follow manufacturer’s instructions.

Pour detergent

into the dry detergent dispenser only.

Slide cover shut, press. PLOP!

15 ml

25 ml

50 ml

Overview of programmes

The max. possible number of programmes is illustrated in this overview. The corresponding programmes for your appliance can be found on the fascia.

The programme data has been measured in the laboratory according to European standard EN50242. Deviations are possible in practice. * half normal load

Quick, economical or intensive ...

Prerinse

Quick

45°

Auto

35°–45°

Eco 50°

Auto

45°–65°

Auto

65°–75°

Energy consumption in kWh

With Aquasensor

Water consumption in litres

Duration: hs : mins

Additional options**

Flexibility…

Express Wash

... is obtained by increased energy consumption at a constant cleaning performance.

Half load

... for a few items, saves water, energy and time.

Extra drying

... improves the drying result by increased temperature in the final rinse. (Please take care with delicate dishes.)

Hygiene

... the temperature is increased during the final rinse process. This increases the hygiene status.

Intensive zone

... perfect for a mixed load. Washing pressure and washing temperature are increased slightly.

** depending on model

(8909) 640 TV

9000 496 328

1:40-2:15 1:30-2:30 2:20 1:05-1:20 0:29 * 0:15 1,30-1,60 0,95-1,60 0,96 0,70-0,85 0,80 0,05

--10-104

11-15 8-19 - 10-15 - -

Maintenance and care

Cleaning waste water pump

CLICK!

For perfect rinsing results ...

Filters

... check, if required, clean.

Rotate filter cylinder, remove filter system...

rinse under running water ...

insert ...

Screw on filter system NOTE MARK!

Spray arms

...Remove blockages/ deposits.

pull lower arm upwards...

unscrew upper arm …

clean spray nozzles under running water (if required use toothpicks) ...

insert lower arm ...

screw on upper

arm tightly

– Pull out the mains plug. – Remove filters and scoop out water. – Lever off cover (A). – Check area around the fan impeller for foreign objects. – Click cover shut (B). – Insert filters.

Rectifying minor faults yourself ...

... as it is worth doing it yourself!

Fault Possible causes

Remedial action

Display “6” is lit

Supply fitting jammed or calcified

1. Unscrew water connection.

2. Clean filter in the water connection.

3. Flow rate must be min. 10l/min., when water supply is open. If the flow rate is less, replace the supply fitting.

Open supply fitting.

Install supply hose without kinks.

Display “E:25” and “6” are lit

Waste water pump blocked

Clean waste-water pump (see above).

Rust on the cutlery

Cutlery not rust-resistant Hard knife blades are more susceptible

Extraneous rust

Use dishwasher-proof cutlery.

Never wash rusting parts in the appliance.

Other fault display “E:XX” is lit

Display “E:24” and “6” are lit

Residual water in the appliance

Appliance has technical defect

Waste water hose is blocked or kinked

Cover not attached to waste water pump

Call factory customer service (state fault display).

Unplug appliance.

Install waste water hose without kinks.

Attach cover (see above).

The programme has not yet ended

Switch on and close the appliance or terminate the programme (see Terminating the programme).

Fault Possible causes

Remedial action

More information can be found in the operating instructions

Utensils are not clean

Sand or gritty residue on the utensils

Utensils are situated close together or one above the other

Too little detergent

Unsuitable programme selected

Spray arm nozzles blocked

Filters dirty, not seated firmly

Spray arms blocked

Separate the utensils, prevent contact points.

Follow manufacturer’s instructions (detergent).

Select a more intensive programme.

Clean the spray arms (see above).

Clean the filters (see above).

Arrange the utensils so that the spray arms can rotate freely.

Stains and streaks

Milky deposits on the utensils (can be removed)

Milky deposits, glasses cloudy/tarnished (cannot be removed)

Plastic/utensils discoloured

Rinse aid dosage too high/too low

Water softening system incorrectly set

No salt

Glasses not dishwasher-proof

Too little detergent

Discoloration caused by food colourings (tomato sauce)

Streaks: reduce dosage.

Water or limescale stains: increase dosage.

Correctly set water softening system.

Refill with special salt.

Use dishwasher-proof glasses.

Use a detergent suitable for glasses.

Follow manufacturer’s instructions (detergent).

Discoloration is harmless; subsequent rinse cycles will cause it to fade.

Utensils not dry

Rinse aid Increase dosage.

Change the product.

The combined detergent used has a poor drying performance

Use rinse aid.

Appliance setting

Activate intensive drying (depending on model).

Dishwasher-proof utensils (not soiled with ash, wax, lubricating grease, ink or adhesive labels; remove large remnants of jam, milk products and food according to the operating instructions and check that the spray arms can rotate freely.

While the programme is running, press the START button for approx. 3 sec. (Reset).

The numerical display indicates “0:01”; approx. 1 minute after the programme ends, “0:00” is indicated.

Switch off the appliance.

Terminating the programme ... Loading the dishwasher correctly ...