Page 1
Register your new Bosch now:
www.bosch-home.com/welcome
Dishwasher
aus
Instruction manual
SM...
SB...
Page 2
5HVHWVHF
6WDUW
Page 3
Table of contents
aus
8 Intended use . . . . . . . . . . . . . . . 4
( Safety instructions . . . . . . . . . . 4
Before you switch ON the
appliance . . . . . . . . . . . . . . . . . . . . . 5
Delivery. . . . . . . . . . . . . . . . . . . . . . . . 5
Installation. . . . . . . . . . . . . . . . . . . . . . 5
In daily use . . . . . . . . . . . . . . . . . . . . . 6
Door lock . . . . . . . . . . . . . . . . . . . . . . 7
Damage . . . . . . . . . . . . . . . . . . . . . . . 7
Disposal . . . . . . . . . . . . . . . . . . . . . . . 7
7 Protection of the
environment . . . . . . . . . . . . . . . . 9
Packaging. . . . . . . . . . . . . . . . . . . . . . 9
Old appliances . . . . . . . . . . . . . . . . . . 9
* Getting to know your
appliance . . . . . . . . . . . . . . . . . . 9
Control panel . . . . . . . . . . . . . . . . . . . 9
Appliance interior . . . . . . . . . . . . . . . . 9
, Rinse aid . . . . . . . . . . . . . . . . . 10
Setting amount of rinse aid. . . . . . . . 11
Switching off rinse aid refill
indicator . . . . . . . . . . . . . . . . . . . . . . 11
- Utensils . . . . . . . . . . . . . . . . . . . 11
Not suitable. . . . . . . . . . . . . . . . . . . . 11
Glass and utensil damage . . . . . . . . 11
Loading the dishwasher . . . . . . . . . . 12
Unloading the dishwasher . . . . . . . . 12
Cups and glasses. . . . . . . . . . . . . . . 12
Pans . . . . . . . . . . . . . . . . . . . . . . . . . 13
Cutlery basket. . . . . . . . . . . . . . . . . . 13
Etagere . . . . . . . . . . . . . . . . . . . . . . . 13
Folding spikes . . . . . . . . . . . . . . . . . 14
Small accessories holder . . . . . . . . . 14
Knife shelf . . . . . . . . . . . . . . . . . . . . . 14
Adjusting the height of the
basket . . . . . . . . . . . . . . . . . . . . . . . . 14
. Detergent . . . . . . . . . . . . . . . . . 15
Adding detergent . . . . . . . . . . . . . . . 16
/ Overview of programmes . . . . 17
Programme selection . . . . . . . . . . . . 18
Information for test institutes . . . . . . . 18
0 Additional options . . . . . . . . . . 19
Express Wash/ Speed Perfect
(VarioSpeed). . . . . . . . . . . . . . . . . . . 19
Half load . . . . . . . . . . . . . . . . . . . . . . 19
Hygiene. . . . . . . . . . . . . . . . . . . . . . . 19
Intensive zone . . . . . . . . . . . . . . . . . . 19
Extra drying. . . . . . . . . . . . . . . . . . . . 19
3
Page 4
aus Intended use
1 Operating the appliance . . . . . 20
Aqua sensor . . . . . . . . . . . . . . . . . . . 20
Switching on the appliance. . . . . . . . 20
Remaining running time display . . . . 20
Timer programming . . . . . . . . . . . . . 20
End of programme . . . . . . . . . . . . . . 21
Switching off automatically
after the end of the programme . . . . 21
Switching off the appliance. . . . . . . . 21
Interrupting the programme . . . . . . . 21
Terminating the programme . . . . . . . 22
Changing the programme. . . . . . . . . 22
Intensive drying. . . . . . . . . . . . . . . . . 22
2 Cleaning and maintenance . . . 22
Overall condition of the machine . . . 22
Rinse aid . . . . . . . . . . . . . . . . . . . . . 23
Filters . . . . . . . . . . . . . . . . . . . . . . . . 23
Spray arms . . . . . . . . . . . . . . . . . . . . 24
3 Fault, what to do? . . . . . . . . . . 24
Waste water pump . . . . . . . . . . . . . . 25
Fault table. . . . . . . . . . . . . . . . . . . . . 26
4 Customer service . . . . . . . . . . 33
5 Installation and
connection . . . . . . . . . . . . . . . . 33
Product package . . . . . . . . . . . . . . . 33
Safety instructions. . . . . . . . . . . . . . . 33
Delivery. . . . . . . . . . . . . . . . . . . . . . . 34
Technical specifications . . . . . . . . . . 34
Installation. . . . . . . . . . . . . . . . . . . . . 34
Waste-water connection . . . . . . . . . . 34
Drinking water connection . . . . . . . . 35
Electrical connection. . . . . . . . . . . . . 35
Removing the appliance . . . . . . . . . . 36
Transportation. . . . . . . . . . . . . . . . . . 36
Protection against frost
(Emptying the appliance) . . . . . . . . . 36
8 Intended use
Intended use
■ This appliance is intended for
use in the home and
domestic environments.
■ Use the dishwasher only in
the home and only for its
designated purpose: for
washing domestic dishes.
■ This appliance is intended for
use up to a maximum altitude
of 4000 metres above sea
level.
( Safety instructions
Safety instructions
This appliance may be used by
children over the age of 8 years
old and by persons with
reduced physical, sensory or
mental capabilities or by
persons with a lack of
experience or knowledge if they
are supervised or are instructed
by a person responsible for
their safety how to use the
appliance safely and have
understood the associated
hazards.
Children must not play with, on,
or around the appliance.
Children must not clean the
appliance or carry out general
maintenance unless they are at
least 8 years old and are being
supervised.
4
Page 5
Safety instructions aus
Keep children below the age of
8 years old at a safe distance
from the appliance and power
cable.
Before you switch ON the
appliance
Please read the instructions for
use and installation carefully.
They contain important
information on how to install,
use and maintain the appliance.
Retain all documents for later
use or for the subsequent
owner.
You can download the
instructions for use from our
website free of charge. The
relevant Internet address can
be found overleaf on these
instructions for use.
Delivery
1. Check the packaging and
dishwasher immediately for
damage caused in transit. Do
not switch on a damaged
appliance, but contact your
supplier.
2. Please dispose of the
packaging material in an
environmentally friendly
manner.
3. Do not let children play with
packaging and its parts.
There is a risk of suffocation
from collapsible boxes and
film.
Installation
■ Following installation, ensure
that the back
of the dishwasher is not
freely accessible (protection
against contact due to hot
surface).
■ Install and connect
the appliance according
to the installation
and assembly instructions.
■ Prior to installation,
disconnect the dishwasher
from the power supply.
■ Ensure that the protective
conductor system
of the domestic supply has
been correctly installed.
■ The electrical connection
conditions must correspond
with the specifications
on the dishwasher rating
plate 9*.
■ If the power cord of this
appliance is damaged,
it must be replaced with
a particular power cord.
To prevent injury, the power
cord may be purchased from
customer service only.
■ If the dishwasher is installed
in a high-sided unit, the unit
must be secured properly.
5
Page 6
aus Safety instructions
■ If the dishwasher is installed
below or above other
domestic appliances, follow
the information for installation
in combination with
a dishwasher
in the installation instructions
for the particular appliances.
■ Also follow the installation
instructions for
the dishwasher to ensure
that all appliances are
operated safely.
■ If there is no information or if
the installation instructions
do not include
the appropriate information,
contact the manufacturer
of these appliances
to ensure that
the dishwasher can be
installed above or below
these appliances.
■ If you cannot obtain any
information from
the manufacturer, you must
not install the dishwasher
above or below these
appliances.
■ If you install a microwave
oven above the dishwasher,
the microwave oven may be
damaged.
■ Install built-under
or integratable appliances
only under continuous
worktops which have been
screwed to adjacent
cupboards to ensure stability.
■ Do not install the appliance
near heat sources (radiators,
heat storage tanks, cookers
or other appliances which
generate heat) and do not
install under a hob.
■ Please note that the
insulation material of the
dishwasher power cord may
melt next to heat sources
(e.g. heating / hot water
installations) or hot appliance
parts. Make sure that the
power cord of the
dishwasher never comes into
contact with heat sources or
hot appliance parts.
■ After installing the appliance,
ensure that the plug is easily
accessible.
(See Electrical connection)
■ Some models:
The plastic housing on the
water connection contains
an electric valve,
the connecting cables
are in the supply hose.
Do not cut through this hose,
do not immerse the plastic
housing in water.
In daily use
Read and observe the safety
information and instructions
for use on the packaging
for cleaning and rinsing agents.
6
Page 7
Safety instructions aus
Childproof lock (door lock)
Door lock
*
The description of the
childproof lock is at the back in
the envelope.
* depending on model
Damage
■ The appliance may be
repaired and opened up by a
technician only. To do this,
disconnect the appliance
from the power supply. Pull
out the mains plug or switch
off the fuse. Turn off the tap.
■ If the appliance is damaged,
especially the fascia (cracks,
holes, broken buttons), or the
door function is impaired,
stop operating the appliance.
Pull out mains plug or switch
off fuse. Turn off tap, call
customer service.
Disposal
1. Make redundant appliances
unusable to prevent
subsequent accidents.
2. Dispose of the appliance in a
n environmentally friendly
manner.
m Warning
Risk of injury!
■ To prevent injuries, e.g.
caused by stumbling, open
the dishwasher only briefly
in order to load and unload
the dishwasher.
■ Knives and other utensils
with sharp points must be
placed in the cutlery basket
with the points
downwards or horizontally on
the knife shelf*.
■ Do not lean or sit
on the open door.
■ In the case of free-standing
appliances, ensure that the
baskets are not overloaded.
■ If the appliance
is not in a cavity and a side
panel is accessible, the door
hinge area must be covered
at the side
for reasons of safety
(risk of injury). The covers
are available as optional
accessories from customer
service or specialist outlets.
* depending on model
7
Page 8
aus Safety instructions
m Warning
Risk of explosion!
Do not add any solvents
to the washing chamber.
Danger of explosion!
m Warning
Risk of scalding!
Open the door carefully when
the programme is still running.
There is a risk of hot water
spraying out of the appliance.
m Warning
Risks to children!
■ If fitted, use the childproof
lock. An exact description
can be
found in the back of the enve
lope.
■ Do not allow children to play
with or operate
the appliance.
■ Keep children away from
detergents and rinse aid.
These may cause chemical
burns in the mouth, throat
and eyes or asphyxiation.
■ Keep children away from
open dishwasher. There may
be small parts in the
dishwasher which children
could swallow and the water
inside the dishwasher is not
drinking water as it may
contain detergent residue.
■ Ensure that children do not
place fingers in the tablet
collecting tray 12. Small
fingers could become
caught in the slots.
■ When opening and closing
the door on an eye-level
appliance, ensure that
children do not become
jammed or crushed between
the appliance door and the
cupboard door below.
■ Children could become
locked in the appliance
(danger of suffocation) or get
into another dangerous
situation.
Redundant appliances: Pull
out the mains plug, sever
and dispose of the power
cord. Destroy the door lock
so that the door can no
longer be closed.
8
Page 9
Protection of the environment aus
7 Protection of the
environment
Protection of the environment
Both the packaging of new appliances
and the old appliances themselves
contain valuable raw materials
and recyclable materials.
Please dispose of the individual parts
separated according to type.
Please ask your dealer or inquire at your
local authority about current means
of disposal.
Packaging
All plastic parts of the appliance are
identified with internationally
standardised abbreviations (e.g. >PS<
polystyrene). Therefore, plastic waste
can be sorted out when the appliance is
being disposed of.
Please follow the safety instructions
under “Delivery”.
Old appliances
Please follow the safety instructions
under “Disposal of your appliance”.
This appliance is labelled in
accordance with European
Directive 2012/19/EU
concerning used electrical and
electronic appliances (waste
electrical and electronic
equipment - WEEE). The
guideline determines the
framework for the return and
recycling of used appliances as
applicable throughout the EU
* Getting to know your
appliance
Getting to know your appliance
Diagrams of the control panel
and the interior of the appliance can be
found in the envelope at the front.
Individual positions are referred
to in the text.
Control panel
( ON/OFF switch
0 Door opener
8 Programme selector
@ START button
H Digital display
P Timer programming *
X Additional options **
` Rinse aid refill indicator
h Display “Check water supply”
* depending on model
** Number depending on model
Appliance interior
1" Top basket
1* Knife shelf *
12 Tablet collecting tray
1: Top spray arm
1B Bottom spray arm
1J Filters
1R Cutlery basket
1Z Bottom basket
1b Dispenser for rinse aid
1j Detergent dispenser
9" Lock for detergent dispenser
9* Rating plate
* depending on model
9
Page 10
aus Rinse aid
, Rinse aid
Rinse aid
As soon as the rinse-aid refill
indicator ` is lit on the fascia, there
is still a rinse-aid reserve of 1-2 rinsing
processes. Refill with rinse aid.
The rinse aid is required for stain-free
utensils and clear glasses. Use only
rinse aid for domestic dishwashers.
Combined detergents with rinse-aid
component may be used up to a water
hardness of 21° dH (37° fH,
26° Clarke, 3.7 mmol/l) only. If
the water hardness is over 21° dH,
rinse aid must be used.
1. Open the dispenser 1b by pressing
and lifting the plate on the cover.
2
1
2. Carefully pour rinse aid up
to the max. mark in the filler opening.
PD[
3. Close cover until it clicks shut.
4. To prevent excessive foam formation
during the next rinse cycle, remove
any rinse aid which has run over with
a cloth.
10
Page 11
Utensils aus
Setting amount of rinse aid
The amount of rinse aid can be set from
§:‹‹ to §:‹‡. Please set rinse aid on
§:‹† to obtain very good drying results
(§:‹† is already set in factory).
Change this setting, only if streaks
(select lower setting) or water stains
(select higher setting) are left on the
utensils.
1. Close the door.
2. Switch on ON/OFF switch (.
3. Press and hold down the START
button @.
4. Rotate programme selector 8
until §:‹... s indicated on the digital
display H.
5. Release button.
The factory set value §:‹† is lit on
the digital display H.
To change the setting:
1. Rotate programme selector 8 until
the required value is indicated on the
digital display H.
2. Press START button @.
The set value is saved.
Switching off rinse aid refill
indicator
If the rinse-aid refill indicator ` is
impaired (e.g. when using combined
detergents containing rinse aid
component), it can be switched off.
■ Proceed as described under “Setting
amount of rinse aid” and set the
value to §:‹‹.
The rinse aid refill indicator ` is now
switched off.
- Utensils
Utensils
Not suitable
■ Cutlery and utensils made of wood.
■ Delicate decorative glasses, craft
and antique utensils. These decors
are not dishwasher-proof.
■ Plastic parts not resistant to heat.
■ Copper and tin utensils.
■ Utensils which are soiled with ash,
wax, lubricating grease or ink.
Aluminium and silver parts have a
tendency to discolour and fade during
the wash cycle. Even some types of
glass (e.g. crystal glass objects) may
turn cloudy after many wash cycles.
Glass and utensil damage
Causes:
■ Glass type and glass production
process.
■ Chemical composition of the
detergent.
■ Water temperature of the wash
programme.
Recommendation:
■ Use only glasses and porcelain
which the manufacturer designates
as dishwasher-proof.
■ Use a detergent which protects
utensils.
■ Take glass and cutlery out of the
dishwasher as soon as possible after
the programme ends.
11
Page 12
aus Utensils
Loading the dishwasher
1. Remove large food remnants. It is
not necessary to prerinse utensils
under running water.
2. Place the utensils so that
– they are secure and cannot tip
over.
– all utensils with their openings
face down.
– parts with curves or indentations
are at an angle, thereby allowing
water to drain.
– does not obstruct rotation of the
two spray arms 1: and 1B.
Very small utensils should not be
washed in the machine, as they may fall
out of the baskets.
Unloading the dishwasher
To prevent water from dripping off the
upper basket onto the utensils in the
lower basket, it is recommended
to empty the appliance from the bottom
up.
Hot utensils are sensitive to shock!
Therefore, when the programme ends,
leave the utensils to cool down in the
dishwasher until they can be handled.
Cups and glasses
Top basket 1"
Note
Utensils must not be placed above the
tablet collecting tray 12. These may
block the lid of the detergent dispenser
and prevent it from opening fully.
Note
When the programme ends, water
droplets can still be seen inside
the appliance. This does not affect
the drying of the utensils.
12
Page 13
Utensils aus
Pans
Bottom basket 1Z
Tip
Heavily soiled utensils (pans) should
be placed in the bottom basket. The
more powerful spray jet provides
a better dishwashing result.
Tip
Other examples, such as the best way
of loading your dishwasher, can
be found on our homepage as a free
download. The corresponding Internet
address can be found on the back page
of these instructions for use.
Cutlery basket
You should always place cutlery
unsorted with the points downwards.
To prevent injuries, place long, pointed
implements and knives on the knife
shelf.
Etagere
Etagere *
The etagere and the space underneath
can be used for small cups and glasses
or for larger items of cutlery, such as
wooden spoons or serving cutlery. The
etagere can be folded up if not required.
CLICK
1
2
3
* Depending on the model, a 3-fold
height adjustment is possible. To do
this, first place the etagere vertically
and pull up, then place at a slight angle,
push down to the required height (1, 2,
or 3) and snap into place.
13
Page 14
aus Utensils
Folding spikes
Folding spikes *
* depending on model
The spikes can be folded down to
improve arrangement of pans, bowls
and glasses.
1
Small accessories holder *
2
Small accessories holder
* depending on model
Light-weight plastic accessories, e.g.
cups, lids, etc. can be held securely in
the small accessories holder.
Knife shelf *
Knife shelf
* depending on model
Long knives and other utensils can be
arranged horizontally.
Adjusting the height of the basket
Adjusting the height of the
basket *
* depending on model
If required, the height of the upper
utensils basket 1" can be adjusted to
provide more space for tall utensils
either in the upper or lower basket.
Appliance height 81.5 cm
Top basket Bottom
Setting 1 max. ø 22 cm 30 cm
Setting 2 max. ø 24.5 cm 27.5 cm
Setting 3 max. ø 27 cm 25 cm
Appliance height 86.5 cm
Top basket Bottom
Setting 1 max. ø 24 cm 33 cm
Setting 2 max. ø 26.5 cm 30.5 cm
Setting 3 max. ø 29 cm 28 cm
Select one of the two following
procedures according to the design of
the top basket for your appliance model:
basket
basket
14
Page 15
Detergent aus
Top basket with side levers
1. Pull out the top basket 1" out.
2. To lower the basket, press in the left
and then the right lever on the
outside of the basket. In doing so,
hold the sides of the basket along
the upper edge to prevent it from
suddenly dropping.
3. To raise the basket, hold the basket
on the sides of the upper edge and
lift it up.
4. Before re-inserting the basket again,
ensure that it is at the same height
on both sides. Otherwise, the
appliance door cannot be closed
and the upper spray arm will not be
connected to the water circuit.
. Detergent
Detergent
You can use tablets as well as powder
or liquid detergents for dishwashers, but
never use washing-up liquid. The
dosage can be individually adjusted with
powder or a liquid detergent according
to the degree of soiling. Tablets contain
an adequately large amount of active
ingredients for all cleaning tasks.
Modern, powerful detergents
predominantly use a low-alkaline
formulation with enzymes. Enzymes
break down starch and remove protein.
To remove coloured stains (e.g. tea,
ketchup), oxygen-based bleaching
agents are generally used.
Note
To ensure a good washing result,
always follow the instructions
on the detergent packaging!
If you have further questions,
we recommend that you contact
the detergent manufacturers’ helpline.
m Warning – Read and observe the
safety information and instructions for
use on the packaging for cleaning and
rinsing agents.
Top basket with upper and
lower roller pairs
1. Pull out the top basket 1" out.
2. Remove the upper basket and re-
attach it to the upper (stage 3) or
lower (stage 1) rollers.
15
Page 16
aus Detergent
Adding detergent
1. If the detergent dispenser 1j is still
closed, press the lock 9" to open
the detergent dispenser.
Pour detergent into the dry detergent
dispenser 1j only (insert tablet flat,
not on its edge).
Dosage: see manufacturer’s
instructions on the packaging.
The graduated detergent
dispenser 1j helps you add the
correct amount of powder or liquid
detergent.
Usually 20 ml–25 ml are adequate
for normal soiling. If using tablets,
one tablet is adequate.
50 ml
25 ml
15 ml
2. Close the cover on the detergent
dispenser by sliding it up until the
lock engages without difficulty.
&/,&.
The detergent dispenser opens
automatically at the optimum time
depending on the programme.
The powder or liquid detergent
is distributed in the appliance and is
dissolved, the tablet falls into
the tablet collecting tray where it
dissolves in doses.
Tip
If the utensils are only lightly soiled,
slightly less than the indicated amount
of detergent is usually adequate.
Suitable detergents and care products
can be purchased online
via our website or via customer service
(see back page).
m Warning – Do not place small parts
for washing in the tablet collecting tray
12; this prevents the tablet from
dissolving evenly.
m Warning – If you want to add more
utensils after the programme
has started, do not use the tablet
collecting tray 12 as a handle
for the upper basket. The tablet could
already be there and you will touch
the partially dissolved tablet.
Notes
■ If programmes are short, tablets
may not have full cleaning effect
due to different dissolving properties
and there may even be undissolved
detergent residue. It is
recommended to use washing
powder for these programmes.
■ The Intensive programme (on some
models) requires one tab only. When
using washing powder, you can
apply some of this cleaning agent
to the inside of the appliance’s door.
■ If using detergents in a water-soluble
protective cover: Take hold of the
cover with dry hands only and put
the detergent into an absolutely
dry detergent dispenser only,
otherwise the detergent may stick.
■ If you switch from combined
detergents to solo detergents,
ensure that the water softening
system and amount of rinse aid have
been set to the correct value.
16
Page 17
Overview of programmes aus
/ Overview of programmes
Overview of programmes
The max. possible number of programmes is illustrated in this overview. The
corresponding programmes for your appliance can be found on the fascia. The
programme data has been measured in the laboratory according to AS/NSZ 2007.
Type of utensils
and soiling
Pots, utensils
and cutlery
Highly soiled
Utensils and
cutlery
Normally soiled
Utensils and
cutlery
Lightly soiled
Programm Programme data
1.) Duration: hs/
mins
2.) Energy
consumption in kWh
3.) Water
consumption in
litres
4.) With Aquasensor
1.) 2:15
ª
Pots and Pans 70°
± / °
intensive 65°
Á
Auto 45° - 65°
Ù / Ø
Normal 45°
ñ / ð
Quick 45°
2.) 1,50
3.) 15
4.) 12
1.) 2:10
2.) 1,40
3.) 14
4.) -
1.) 1:35-2:40
2.) 1,00-1,60
3.) -
4.) 9-19
1.) 2:20
2.) 0,73
3.) 13,5
4.) -
1.) 0:29
2.) 0,80
3.) 10
4.) -
Possible
additional
options
all
all
all
all
Extra drying
Programme
sequence
Prerinse
Clean 70°
Intermediate rinse
Final rinse 70°
Dry
Prerinse
Clean 65°
Intermediate rinse
Final rinse 70°
Dry
Is optimised according
to the soiling with the
aid of sensors.
Prerinse
Clean 45°
Intermediate rinse
Final rinse 45°
Dry
Clean 45°
Intermediate rinse
Final rinse 55°
17
Page 18
aus Overview of programmes
all types
of utensils
Lightly soiled
ù / ø
Prerinse
1.) 0:15
2.) 0,05
3.) 4
4.) -
Note
The consumption figures depend on the
selected programme and additional
functions. The programme duration will
be different if the machine is short of
rinse additive or the function is turned
off.
Programme selection
You can select a suitable programme
according to the type of utensils and
degree of soiling.
Information for test institutes
Test institutes can request the
conditions for running comparison tests
by sending an e-mail to
dishwasher@test-appliances.com.
Quote the appliance number (ENr.)
and the production date (FD) which you
can find on the rating
plate 9* on the appliance door.
none
Cold rinse:
Prerinse
18
Page 19
Additional options aus
0 Additional options
Additional options
* depending on model
Additional options can be set with
the buttons X.
Express Wash/ Speed Perfect (VarioSpeed)
Ÿ Express Wash/ Speed
Perfect/ (VarioSpeed) *
This function can reduce the running
time by approx. 20% to 50% depending
on the selected rinse programme. The
change in the running time is indicated
on the digital display H. To obtain
optimum cleaning results at a reduced
running time, water and energy
consumption are increased.
Half load
§ Half load *
If you have only a few items to wash
(e.g. glasses, cups, plates), you can
switch to “half load”. This will save
water, energy and time. It is
recommended to put a little less
detergent in the detergent dispenser
than for a full load.
· Hygiene *
Hygiene
The temperature is increased during the
cleaning process. This increases the
hygiene status. This additional option is
ideal for cleaning e.g. chopping boards
and baby bottles.
Ï Intensive zone *
Intensive zone
Perfect for a mixed load. You can wash
very soiled pots and pans in the lower
basket together with normally soiled
utensils in the upper basket. The spray
pressure in the lower basket is
intensified, the rinsing temperature is
increased slightly.
¿ Extra drying *
Extra drying
An increased temperature during the
final rinse and an extended drying
phase ensure that even plastic parts dry
better. There is a slight increase in the
energy consumption.
19
Page 20
aus Operating the appliance
1 Operating
the appliance
Operating the appliance
Aqua sensor
Aqua sensor *
* depending on model
The Aqua sensor is an optical
measuring device (light barrier) which
measures the turbidity of the rinsing
water.
The Aqua sensor is used according to
the programme. If the Aqua sensor is
active, “clean” rinsing water can be
transferred to the next rinse bath and
water consumption can be reduced by
3–6 litres. If the turbidity is greater, the
water is drained and is replaced with
fresh water. In the automatic
programmes the temperature and
running time can also be adjusted to the
degree of soiling.
Switching on the appliance
1. Turn on the tap fully.
2. Switch on ON/OFF switch (.
3. Rotate programme selector 8 to
the required programme.
The expected programme duration
flashes on the digital display H.
4. Press START button @.
The programme starts running.
Remaining running time
display
When the programme is selected, the
remaining running time of the
programme is indicated on the digital
display H.
The running time is determined during
the programme by the water
temperature, the number of utensils as
well as the degree of soiling and may
vary (depending on the selected
programme).
Timer programming
Timer programming *
* depending on model
You can delay the start of the
programme in 1-hour steps up to
24 hours.
1. Close the door.
2. Switch on ON/OFF switch (.
3. Press button P until the digital
display H jumps to œ:‹‚.
4. Press button P until the displayed
time corresponds with your
requirements.
5. Press START button @, timer
programming is activated.
6. To delete the preselected starting
time, press the button P until œ is
indicated on the digital display.
You can change your programme
selection at any time until the
programme starts.
20
Page 21
Operating the appliance aus
End of programme
The programme has ended when the
value ‹:‹‹ is indicated on the numerical
display H.
Switching off automatically
after the end of
the programme *
* depending on model
To save energy, the dishwasher is
switched off 1 minute after the
programme ends (factory setting).
Automatic disconnection
can be adjusted from ˜:‹‹ to ˜:‹ƒ.
˜:‹‹ Appliance does not switch off
automatically
˜:‹‚ Off after 1 min
˜:‹ƒ Off after 120 min
1. Close the door.
2. Switch on ON/OFF switch (.
3. Press and hold down the START
button @.
4. Rotate programme selector 8
until ˜:‹... s indicated on the digital
display H.
5. Release button.
The factory set value ˜:‹‚ is lit on
the digital display H.
To change the setting:
1. Rotate programme selector 8 until
the required value is indicated on the
digital display H.
2. Press START button @.
The set value is saved.
Switching off automatically after the end of the programme
Switching off the appliance
Short time after the end of the
programme:
1. Switch off ON/OFF switch (.
2. Turn off the tap (not applicable if
Aqua-Stop fitted).
3. Open the door.
4. Remove the utensils when they have
cooled down.
Note
When the programme ends, leave
the appliance to cool down a while
before opening it. This will prevent
steam from escaping and causing longterm damage to your built-in furniture.
Interrupting the programme
1. Switch off ON/OFF switch (.
The LEDs go out. The programme is
saved.
If the door was opened on an
appliance which has a warm water
connection or is heated, first leave
the door ajar for several minutes and
then close. Otherwise, expansion
(pressure) may cause the appliance
door to spring open or water to run
out of the appliance.
2. To continue the programme, switch
on the ON/OFF switch ( again.
21
Page 22
aus Cleaning and maintenance
Terminating the programme
Terminating the programme
(Reset)
1. Press START button @ for
approx. 3 sec.
The numerical display H
indicates ‹:‹‚.
2. The programme sequence lasts
approx. 1 min. On the digital
display H is indicated ‹:‹‹.
3. Switch off ON/OFF switch (.
2 Cleaning and
maintenance
Cleaning and maintenance
A regular inspection and maintenance
of your machine will help to prevent
faults. This saves time and prevents
problems.
Overall condition
of the machine
Changing the programme
When the START button @ has been
pressed, the programme cannot be
changed.
The only way a programme can be
changed is by Cancel programme
(Reset).
Intensive drying
The final rinse uses a higher
temperature which improves the drying
result. The running time may increase
slightly. (Caution if utensils are delicate!)
1. Close the door.
2. Switch on ON/OFF switch (.
3. Press and hold down the START
button @.
4. Rotate programme selector 8
until š:‹‹ is indicated on the digital
display H.
5. Release button.
The factory-set value š:‹‹ is lit on
the digital display H (intensive
drying off).
Change the setting as follows:
1. By rotating the programme selector
8, you can switch intensive drying
on š:‹‚ or off š:‹‹.
2. Press START button @.
The set value is saved.
■ Check spray arm for grease
and limescale deposits.
If you find such deposits:
■ Fill detergent dispenser with
detergent. Start the appliance without
utensils in the programme with
the highest rinsing temperature.
Clean the appliance with detergents/
appliance cleaners which
are particularly suitable for use with
dishwashers.
■ To extend the life of your appliance,
clean the appliance regularly with a
special dishwasher detergent.
■ To ensure that the door seal always
remains clean and hygienic, regularly
clean it with a damp cloth and a little
washing-up liquid.
■ If the appliance is switched off for
a prolonged period, leave the door
ajar to prevent the formation of
an unpleasant odour.
22
Page 23
Cleaning and maintenance aus
Never use a steam cleaner to clean your
dishwasher. The manufacturer is not
liable for any consequential damage.
Regularly wipe the front of the appliance
and fascia with a damp cloth; water
and a little washing up liquid
are adequate. Do not use sponges with
a rough surface or abrasive detergents,
as these could scratch the surfaces.
Stainless steel appliances: To prevent
corrosion, avoid using sponge cloths
or wash them out thoroughly several
times before using for the first time.
m Warning – Health hazard
Never use other domestic detergents,
e.g. containing chlorine!
Rinse aid
■ Check the refill indicator `. If
required, refill rinse aid.
Filters
The filters 1J keep large foreign
objects in the rinsing water away from
the pump. These foreign objects may
occasionally block the filters.
The filter system consists of a coarse
filter, a flat fine filter and a microfilter.
1. After each washing cycle check the
filters for residue.
2. Unscrew filter cylinder as illustrated
and take out filter system.
3. Remove any residue and clean filters
under running water.
4. Re-install filter system in reverse
sequence and ensure that the arrow
marks are opposite each other after
closing the filter system.
23
Page 24
aus Fault, what to do?
Spray arms
Limescale and contaminants in the
rinsing water may block nozzles and
bearings on the spray arms 1: and
1B.
1. Check outlet nozzles on the spray
arms for blockages.
2. Unscrew the upper spray arm 1:.
3. Remove the lower spray arm 1B
upwards.
4. Clean spray arms under running
water.
5. Re-engage or screw on spray arms.
3 Fault, what to do?
Fault, what to do?
Experience has shown that you can
rectify most faults which occur in daily
operation yourself. This ensures that
the machine is quickly available to you
again. In the following overview you can
find possible causes of malfunctions
and helpful information for rectifying
them.
Note
If the appliance stops during
dishwashing or does not start for no
obvious reason, first run the Abort
programme function (Reset).
(See chapter entitled “Operating
the appliance”)
m Warning – Don’t forget: Repairs may
be carried out by technicians only. If a
component has to be replaced, ensure
that only original spare parts are used.
Improper repairs or use of non-original
spare parts may cause considerable
damage and put the user at
considerable risk.
24
Page 25
Fault, what to do? aus
Waste water pump
Large food remnants or foreign objects
which were not captured by the filters
may block the waste water pump. The
rinsing water will then be above
the filter.
m Warning – Risk of cuts!
When cleaning the waste water pump,
ensure that you do not injure yourself
on pieces of broken glass or pointed
implements.
In this case:
1. First always disconnect
the appliance from the power supply.
2. Take out top basket 1" and bottom
basket 1Z.
3. Remove the filters 1J.
4. Scoop out water, use a sponge if
required.
5. Prise out the white pump cover
(as illustrated) using a spoon. Grip
the cover on the crosspiece and lift
diagonally inwards. Remove cover
completely.
6. Check impeller wheel and remove
any foreign objects.
7. Place cover in the original position
and press down until it engages
(click).
2
3
&/,&.
8. Install filters.
9. Re-insert baskets.
1
25
Page 26
aus Fault, what to do?
Fault table
Fault Cause Remedial action
“Check water supply”
display h lights up.
Error code “:‹ˆ is lit. Intake opening (on right inside of
Error code “:‚ƒ is lit. Heating element soiled. Clean appliance with dishwasher cleaning
Fault code “:‚… is lit. Water protection system
Fault code “:‚† is lit.
Fault code “:‚‡ is lit. Constant water inflow.
Error code “:ƒƒ is lit. Filters 1J are soiled or
Error code “:ƒ… is lit. Waste water hose
Error code “:ƒ† is lit. Waste water pump blocked
Supply hose kinked. Install supply hose without kinks.
Tap turned off. Turn on the tap.
Tap jammed or calcified. Turn on the tap.
Flow rate must be min. 10 l/min.
when water supply is open.
Filter in the water supply blocked. Switch off the appliance and pull out
the mains plug. Turn off the tap. Unscrew
water connection.
Clean filter in the supply hose. Screw water
connection on again. Check for leaks.
Reconnect power supply. Switch on
the appliance.
appliance) covered by utensils.
activated.
blocked.
is blocked or kinked.
Siphon connection still sealed. Check connection to siphon and open if
Cover on the waste water pump
loose.
or cover on the waste water
pump is not locked in position.
Arrange utensils so that the intake opening
is not obstructed.
agent.
Turn off tap.
Call customer service and mention the fault
code.
Clean filters.
(See Cleaning and maintenance)
Install hose without kinks, remove any
residue.
required.
Lock cover correctly.
(See Waste water pump)
Clean pump and lock cover correctly. (See
Waste water pump)
26
Page 27
Fault, what to do? aus
Fault Cause Remedial action
Error code “:ƒˆ is lit. Mains voltage too low. Not an appliance fault, have the mains
voltage and electrical installation checked.
A different error code is
indicated on the digital
display.
(“:‹‚ to “:„‹)
A technical fault has probably
occurred.
Switch off appliances with the ON/OFF
switch (. After a short time restart
the appliance.
If the problem recurs, turn off the tap and
pull out the mains plug.
Call customer service and mention the error
code.
Display flashes Door not closed properly. Close the door. Ensure that no objects
(utensil, fragrance dispenser) are protruding
over the basket and preventing the door
from closing.
Refill indicator for rinse-aid
No rinse aid. Refill rinse aid.
` is lit.
Refill indicator for rinse-aid
` is not lit.
Refill indicator switched off. Activation/deactivation (see chapter Rinse
aid).
There is still enough rinse aid
Check refill indicator, level.
available.
Water is left
in the appliance at the end
of the programme.
Filter system or area under
the filters 1J is blocked.
The programme has not yet
ended.
Clean filters and area underneath (see
Waste water pump).
Wait until programme ends or reset (see
Terminating the programme).
27
Page 28
aus Fault, what to do?
Fault Cause Remedial action
Utensils not dry. No or too little rinse aid
Refill rinse aid.
in the dispenser.
Programme selected without
drying.
Select programme with drying (see
Overview of programmes, Programme
sequence).
Water collecting in depressions
on the utensils and cutlery.
Arrange utensils in a sloping position,
arrange affected utensils as sloping
as possible.
The combined detergent used
has a poor drying performance.
Use different combination detergent with
better drying performance. Use of rinse aid
also increases the drying performance.
Intensive drying to increase
drying not activated.
Utensils were removed too early
or drying process had not ended
yet.
The eco rinse aid used has a poor
drying performance.
Activate intensive drying (see Operating
the appliance)
Wait until program ends or wait until 30 min
after program ends before removing
utensils.
Use a proprietary rinse aid. Eco products are
much less effective.
Plastic utensils not dry. Special properties of plastic. Plastic has a lower heat storage capacity
and therefore dries less well.
Cutlery not dry. Cutlery not arranged properly
in the cutlery basket.
Cutlery not arranged properly
in the cutlery drawer.
Appliance interior wet after
No appliance fault. On account of the “Condensation drying”
rinse cycle.
Separate cutlery if possible, prevent contact
points.
Arrange cutlery properly and separate if
possible.
principle, water droplets are physically
induced and required in the container. The
humidity in the air condenses on the inner
walls of the dishwasher, drains and is
pumped out.
28
Page 29
Fault, what to do? aus
Fault Cause Remedial action
Food remnants
on the utensils.
Utensils placed too closely
together, utensils basket
overfilled.
Arrange utensils with adequate clearance
between them ensuring that the spray jets
can reach the surface of the utensils.
Prevent contact points.
Spray arm rotation obstructed. Arrange utensils so that the spray arm can
rotate without obstruction.
Spray arm nozzles blocked. Clean the spray arm nozzles,
(See Cleaning and maintenance).
Filters 1J dirty. Clean filters, (see Cleaning and
maintenance).
Filters 1J inserted incorrectly
Insert and engage filters correctly.
and/or not engaged.
Rinse programme too weak. Select a more intensive rinse programme.
Utensils precleaned too intensely;
sensors therefore decide on
Do not prerinse utensils. Remove only large
food remnants.
weak programme sequence.
Stubborn soiling cannot be
completely removed.
Tall narrow receptacles in corner
areas are not rinsed adequately.
Do not place hollow receptacles too
obliquely and do not place in the corner
area.
Top basket 1" on right and left
not set to same height.
Detergent residue Detergent dispenser cover
blocked by utensils and therefore
does not open fully.
Set top basket to same height using side
levers.
Detergent dispenser cover must not be
obstructed by utensils.
Do not place utensils or fragrance dispenser
in the tablet collecting tray.
Detergent dispenser cover
Tablet must be inserted flat and not upright.
blocked by the tablet.
Tablets used in the quick or short
programme.
Dissolving time of the detergent
is not reached in the selected
Dissolving time of tablets too long for
a quick or short programme.
Use a detergent powder or select a more
intensive programme.
short programme.
Washing effect and dissolving
Change detergent.
performance are reduced after
a prolonged storage time or
detergent is very lumpy.
Water stains on plastic
parts
Droplet formation on plastic
surface is physically unavoidable.
After drying, water stains are
visible.
Use a more intensive programme (more
water changes).
Arrange utensils in a sloping position.
Use rinse aid.
29
Page 30
aus Fault, what to do?
Fault Cause Remedial action
Washable or water-soluble
coatings in the container or
on the door.
Detergent substances are
deposited. These coatings cannot
usually be removed with
Change detergent brand.
Clean appliance mechanically.
chemicals (appliance cleaner, ...).
Only for glasses: Initial glass
See Glass and utensil damage.
corrosion – can only apparently
be wiped off.
White, stubborn coatings;
limescale on the utensils,
container or door.
Detergent substances are
deposited. These coatings cannot
usually be removed with
Change detergent brand.
Clean appliance mechanically.
chemicals (appliance cleaner, ...).
Underdosing of detergent. Increase detergent dosage or change
detergent.
Too weak rinse programme
Select a more intensive rinse programme.
selected.
Tea or lipstick residue on
the utensils.
Too low rinsing temperature. Select programme with higher washing
temperature.
Too little or unsuitable detergent. Use suitable detergent at correct dosage.
Utensils precleaned too intensely;
sensors therefore decide on
Do not prerinse utensils. Remove only large
food remnants.
weak programme sequence.
Stubborn soiling cannot be
completely removed.
Coloured (blue, yellow,
brown), difficult to remove
to non-removable coatings
in the appliance or on
stainless steel utensils.
Film formation consisting
of ingredients from vegetables
(e.g. cabbage, celery, potatoes,
noodles, ...) or the tap water (e.g.
manganese).
Film formation caused by metallic
components on silver or
Can be partly removed with machine
cleaner or by mechanical cleaning. Coatings
are harmless.
Can be partly removed with machine
cleaner or by mechanical cleaning.
aluminium utensils.
Discolouration of the
plastic parts inside the
appliance.
Plastic parts inside the appliance
may become discoloured during
the service life of the dishwasher.
Discolouration is normal and will not impair
the function of the dishwasher.
Plastic parts discoloured. Too low rinsing temperature. Select programme with higher washing
temperature.
Utensils precleaned too intensely;
sensors therefore decide on
Do not prerinse utensils. Remove only large
food remnants.
weak programme sequence.
Stubborn soiling cannot be
completely removed.
30
Page 31
Fault, what to do? aus
Fault Cause Remedial action
Removable streaks on
glasses, glasses with
metallic appearance and
cutlery.
Too much rinse aid. Set rinse aid amount to lower setting.
No rinse aid added or setting too
low.
Detergent residue in the final
rinse programme section.
Detergent dispenser cover
blocked by utensils (cover does
not open fully).
Utensils precleaned too intensely;
sensors therefore decide on
Add rinse aid and check dosage
(recommended setting 4-5).
Detergent dispenser cover must not be
obstructed by utensils.
Do not place utensils or fragrance dispenser
in the tablet collecting tray.
Do not prerinse utensils. Remove only large
food remnants.
weak programme sequence.
Stubborn soiling cannot be
completely removed.
Initial or existing,
irreversible clouding
of glass.
Glasses not dishwasher-proof,
only suitable for dishwasher.
Use dishwasher-proof glasses.
Avoid long steam phase (standing time after
wash cycle ends).
Use wash cycle at lower temperature.
Use detergent with glass protection
component.
Rust spots on the cutlery. Cutlery not adequately rust-
Use corrosion-resistant cutlery.
resistant. Knife blades are
frequently more severely
affected.
Cutlery will also rust if rusting
Do not wash rusting parts.
parts are rinsed at the same time
(pan handles, damaged utensil
baskets, etc.).
The appliance does not
start.
The mains fuse has tripped. Check mains fuse.
Power cord not inserted. Ensure that the power cord is plugged all
the way into the back of the appliance and
into the socket. Check that the socket
functions.
The appliance door has not been
Close the door.
shut properly.
Programme starts
automatically.
The door is difficult
to open.
You did not wait until programme
ended.
Perform reset.
(See Terminating the programme).
Child-proof lock is activated. Deactivate childproof lock. (See instructions
for use at the back)
Door cannot be closed. Door lock has been activated. Close door with increased force.
Door cannot be closed due to
installation.
Check appliance installation: Door or
attached parts must close without
obstruction.
31
Page 32
aus Fault, what to do?
Fault Cause Remedial action
Cover on the detergent
dispenser cannot be
closed.
Detergent residue
in the detergent dispenser
or in the tablet collecting
tray.
Appliance stops
in the programme or
programme is interrupted.
Filling valves making
striking noises.
Knocking or rattling noise. Spray arm strikes the utensils,
Unusual foam formation. Handwash liquid in the rinse aid
Detergent dispenser or cover
guide blocked by sticky detergent
residue.
Spray arms blocked by utensils,
therefore detergent is not rinsed
out.
The detergent dispenser was
damp when filled.
Door not closed properly. Close the door.
Do not place utensils or fragrance
dispenser in the tablet collecting
tray.
Top basket presses against inner
door and prevents door from
being closed securely.
Power and/or water supply
interrupted.
Depends on domestic installation,
as appliance is not defective. No
effect on appliance function.
utensils not positioned correctly.
If there is a low load, the water
jets strike the washing tank
directly.
Light utensils move during
the wash cycle.
dispenser.
Rinse aid spilled. Remove rinse aid with a cloth.
Remove detergent residue.
Ensure that the spray arms can rotate freely.
Pour detergent into the dry detergent
dispenser only.
Check whether rear panel is being pressed
in, e.g. by socket or by hose holder which
has not been removed.
Restore power and/or water supply.
No remedial action possible.
Position utensils so that the spray arms do
not strike the utensils.
Load the appliance with more utensils or
distribute the utensils more evenly
in the dishwasher.
Arrange light utensils securely.
Immediately refill rinse aid dispenser with
rinse aid.
32
Page 33
Customer service aus
4 Customer service
Customer service
If you are unable to rectify the fault,
please contact your customer service.
We always find a suitable solution, even
to avoid unnecessary visits
by technicians. Contact information
for your nearest customer service can
be found on the back of these
instructions for use or on the enclosed
customer service list. When calling,
please state the appliance number (ENr. = 1) and the production number
(FD = 2) which can be found on the
rating plate 9* on the appliance door.
(1U
)'
Rely on the competence of the manufa
cturer. Contact us. You can therefore be
sure that the repair is carried out
by trained service technicians who carry
original spare parts for your domestic
appliances.
5 Installation and
connection
Installation and connection
The dishwasher must be connected
correctly, otherwise it will not function
properly. The specifications for the inlet
and outlet as well as the electrical
connected loads must correspond with
the required criteria as
specified in the following paragraphs
or in the installation instructions.
Install the appliance in the correct
sequence:
1. Checking appliance on delivery
2. Installing the appliance
3. Waste water connection
4. Drinking water connection
5. Electrical connection
Product package
If you have any complaints, contact
the dealer where you purchased
the appliance or our customer service.
■ Dishwasher
■ Instructions for use
■ Installation instructions
■ Warranty*
■ Installation materials
■ Steam guard plate*
■ Rubber apron*
■ Power cord
* depending on model
Safety instructions
Please follow the safety instructions
under “Installation”.
33
Page 34
aus Installation and connection
Delivery
Your dishwasher has been checked
thoroughly in the factory to ensure that it
is in working order. This may cause
small water stains. These will disappear
after the first wash cycle.
Technical specifications
Weight:
max. 60 kg
Voltage:
220–240 V, 50 Hz or 60 Hz
Connected load:
2000–2400 W
Fuse:
10/16 A (UK 13A)
Power input:
switched off 0.10 W
not switched off 0.10 W
Water pressure:
at least 0.05 MPa (0.5 bar), maximum
1 MPa (10 bar). At a higher water
pressure: connect pressure-reducing
valve ahead.
Inlet rate:
minimum 10 litres/minute
Water temperature:
for cold water connection only.
Capacity:
12–15 place settings (depending
on model).
Installation
The required installation dimensions can
be found in the installation instructions.
Level the appliance with the aid of the
height-adjustable feet. Ensure that the
appliance is situated securely on the
floor.
■ A built-under or integrated appliance
which is installed subsequently as a
free-standing appliance must be
secured to prevent it from
overturning, e.g. by screwing it to the
wall or by installing it under
a continuous worktop which is
screwed to adjacent cupboards.
■ The appliance can easily be
installed in a fitted kitchen between
wooden and plastic walls.
Waste-water connection
1. The required work sequence can be
found in the installation instructions.
If required, fit a siphon with an
drainage connection.
2. Connect the waste-water hose to the
drainage connection of the siphon
with the enclosed parts.
Ensure that the drainage hose is not
kinked, crushed or twisted and that
there is no cover plate in the
drainage to prevent the waste water
from flowing out!
34
Page 35
Installation and connection aus
Drinking water connection
1. Fasten the drinking water connection
to the tap according
to the installation instructions using
the enclosed parts.
Ensure that the drinking water
connection is not kinked, crushed
or twisted.
2. When replacing the appliance,
always use a new water supply hose.
Water pressure:
at least 0.05 MPa (0.5 bar), maximum
1 MPa (10 bar). At a higher water
pressure: connect pressure-reducing
valve ahead.
Inlet rate:
minimum 10 litres/minute
Water temperature:
for cold water connection only.
Electrical connection
■ Connect the appliance to an
alternating current only, ranging from
220 V to 240 V and 50 Hz or 60 Hz
via a correctly installed socket with
protective earth conductor. See
rating plate for required fusing 9*.
■ The socket must be near
the appliance and freely accessible
following installation.
If the plug is not freely accessible, an
allpole disconnector with a contact
opening of at least 3 mm must be
fitted on the installation side
to satisfy the relevant safety
instructions.
■ The connection may be modified by
technicians only.
■ A power cord extension may be
purchased from customer service
only.
■ Use only a residual current operated
circuit-breaker which features
the symbol ‚. Only this extension
guarantees compliance with
the currently valid regulations.
■ The appliance features a water
damage protection system. Please
note the system will not function
unless the power supply
is connected.
35
Page 36
aus Installation and connection
Removing the appliance
Also observe
the sequence of worksteps here.
1. Disconnect the appliance from
the power supply.
2. Turn off the water supply.
3. Undo the waste water and drinking
water connection.
4. Loosen fastening screws for
the furniture parts.
5. If fitted, remove the base panel.
6. Pull out the appliance, carefully
pulling the hose behind.
Transportation
Empty the dishwasher and secure loose
parts.
Drain the appliance according to the
following steps:
1. Turn on the tap.
2. Close the door.
3. Switch on ON/OFF switch (.
4. Select programme with the highest
temperature.
The expected programme duration is
indicated on the numerical display
H.
5. Press START button @.
Programme sequence starts.
6. After approx. 4 minutes press the
START button @ until ‹:‹‚ is
indicated on the digital display.
After approx. 1 min is indicated on
the digital display ‹:‹‹.
7. Switch off ON/OFF switch (.
8. Turn off the tap, disconnect supply
hose and drain water.
Transport appliance upright only.
(This prevents residual water from
running into the machine control and
damaging the programme sequence.)
Protection against frost
Protection against frost (Emptying the appliance)
If the appliance is in a room where there
is a risk of frost (e.g. holiday home),
empty the appliance completely (see
Transportation).
36
6XEMHFWWRFKDQJHV
Page 37
&KLOGSURRIORFNGRRUORFN
$FWLYDWHWKHFKLOGSURRIORFN
2SHQWKHGRRUZLWKDFWLYDWHG
FKLOGSURRIORFN
'HDFWLYDWHFKLOGSURRIORFN
%DNLQJVKHHWVSUD\KHDG
:DUQLQJ
$OZD\VFORVHWKHDSSOLDQFHGRRUFRPSOHWHO\
ZKHQ\RXOHDYHWKHDSSOLDQFH
7KLVLVWKHRQO\ZD\\RXFDQSURWHFW\RXU
FKLOGUHQIURPSRWHQWLDOGDQJHUV
/DUJHVKHHWVRUJULOOHVDQGSODWHVZKLFKKDYHDGLDPHWHUJUHDWHUWKDQFPJRXUPHW
SODWHVSDVWDSODWHVGLQQHUSODWHVFDQEHFOHDQHGZLWKWKHDLGRIWKHVSUD\KHDG
7RGRWKLVUHPRYHWKHWRSEDVNHWDQGLQVHUWWKHVSUD\KHDGDVLOOXVWUDWHGLQWKHGLDJUDP
7RHQVXUHWKDWWKHVSUD\MHWFDQUHDFKDOOSDUWVDUUDQJHWKHEDNLQJVKHHWVDVLOOXVWUDWHG
PD[âEDNLQJVKHHWVDQGâJULOOHV
1HYHURSHUDWHWKHGLVKZDVKHUZLWKRXWWKHWRSEDVNHWRUEDNLQJVKHHWVSUD\KHDG
VRPHPRGHOV
Page 38
AquaStop guarantee
(does not apply to appliances without AquaStop)
Contact information for all countries can be found on the enclosed customer service list.
Repair order and advice on faults.
GB 0344 892 8979 Calls from a BT landline will be charged at up to 3 pence per minute.
A call set-up fee of up to 6 pence may apply.
Robert Bosch Hausgeräte GmbH
www.bosch-home.com
Carl-Wery-Straße 34
81739 München
Germany
4.
If your appliance is fitted with AquaStop, you can leave your appliance
unattended during operation and leave the tap turned on afterwards.
The tap should only be turned off if you are absent from home for
a prolonged period, e.g. several weeks holiday.
In addition to warranty claims against the seller based on the purchase contract
and in addition to our appliance warranty we will pay damages under
the following conditions:
1.
If our AquaStop system is defective and causes water damage,
we will make good the damage for private users.
To ensure water damage protection, the appliance must be connected
to the power supply.
3.
A prerequisite for the warranty claim is that the appliance has been correctly
installed and connected with AquaStop according to our instructions.
This also includes the correct installation of the AquaStop extension
(original accessory). Our warranty does not extend to defective
feed lines or fittings up to the AquaStop connection on the tap.
2.
This liability guarantee is valid for the service life of the appliance.
IE 01450 2655
US 800 944 2904
toll-free
0.03 € per minute at peak. Off peak 0.0088 € per minute.
*9000940624*
9000940624 en (9801) 640EG
Loading...