Bosch SHU 8810, SHV 4800, SHV 6800, SHU 3300, SHV 4300 User Manual 3
...
Rinse
& Hold
Regular
Wash
Power Scrub
Cycles
Power
On/Off
Delay
Start
Hours
Top
Rack
Only
Cancel
Drain
Power
Scrub
Plus
Scrub
Wash
Regular
Wash
Delicate/
Econo
Quick
Wash
Rinse
& Hold
Refill
Rinse
Agent
Cycle Countdown
Rinse
&
Hold
On /Off
Temp.Options
High
Temp
Wash
Power
Regular
Temp
Wash
DISHWASHER
Installation
Instructions
LAVE-VAISSELLE
Instructions
d’installation
LAVADORA DE PLATOS
Instrucciones
de instalación
SHV 6800, 4800,4300
SHI 6800,4300
SHU 9950, 9920, 9910, 8810, 8800, 6800, 5300,
4320,3300, 3131, 3030
TABLE OF CONTENTS
INTRODUCTION .................................................. .2
TOOLS AND MATERIALS NEEDED ..........................3
MATERIALS SUPPLIED........................................... 4
CHOOSING LOCATION ........................................ .5
PLUMBING PREPARATION .................................... .6
ELECTRICAL PREPARATION .................................. .7
PLACING THE DISHWASHER ................................ . 8
DRAIN HOSE CONNECTION ................................. .9
HOT WATER CONNECTION .................................. 10
ELECTRICAL SUPPLY CONNECTION ...................... 11
GROUNDING INSTRUCTIONS .............................. 11
DOOR PANEL INSTALLATION ....................... 12 & 13
FINAL ADJUSTMENTS .......................................... 14
BASE AND TOE PANEL .........................................15
TOE PANEL AND HANDLE ..................................... 16
FINAL CHECKLIST ............................................... 17
ENGLISH
ENGLISHENGLISH
ENGLISHENGLISH
IMPORTANT: Before you begin, read these instructions completely and carefully.
INSTALLER: Please leave this manual with owner for future reference.
OWNER: Save these installation instructions for local
electrical inspector’s use and for future reference.
www.boschappliances.com
ENGLISH - 1
INTRODUCTION
THESE INSTALLATION INSTRUCTIONS ARE INTENDED
FOR USE BY QUALIFIED INSTALLERS.
In addition to these instructions the dishwasher shall be installed:
• In the United States, in accordance with the National Electric
Code/State and Municipal codes and/or local codes.
• In Canada, in accordance with the Canadian Electric Code
C22.1 -latest edition/Provincial and Municipal codes and/or
local codes.
Please read these installation instructions completely and carefully
They will save you time and effort and help to ensure optimum dishwasher
performance.
Be sure to observe all listed
warnings and cautions. (Look for
the triangles with exclamation marks
inside.)
WARNING
CAUTION
.
IMPORTANT
• NEW INSTALLATION - If the dishwasher is a new installation, most of the work
must be done
before the dishwasher is moved into place.
• REPLACEMENT - If the dishwasher is replacing another dishwasher, the
connections for the dishwasher being replaced
compatibility
with the new dishwasher and replaced as necessary .
INSPECT THE DISHWASHER
After unpacking the dishwasher and prior to installation, thoroughly inspect the
dishwasher for possible freight or cosmetic defect. Report an y defect immediately .
Cosmetic defects must be reported within 30 days of installation.
must be checked for
NOTE: Please do not discard any bags or items that come with the
original package until after the entire installation has been completed!
2 - ENGLISH
www.boschappliances.com
TOOLS & MATERIALS NEEDED
Tools Needed for Installation
Pipe wrench, 2 reqd.
Adjustable wrench,
(size med., 2 reqd.)
Wire stripper
Figure 1
Materials Needed
1
2
Hammer
Tape Measure
Wire Cutter
Electric Drill
Electric Connection - 2 conductor , 1 ground
insulated electrical supply cable (30” or
sufficient length for
Hot Water Supply Line - Minimum 3/8”
O.D. copper tubing or metal braided
dishwasher supply line.
Hole saw or 1 hole cutter
Slotted screwdriver (#2)
Phillips screwdriver (#2)
Torx screwdriver, #20
Level
your
installation).
ENGLISH
ENGLISHENGLISH
ENGLISHENGLISH
3
4
TA
P
5
E
6
7
Additional materials may be required to comply with local codes.
Figure 2
Shut-off valve and fittings for hot water
supply line.
90° elbow with 3/8” N.P .T. external threads
on one end and sized to fit your water
supply line on the other end.
T eflon tape or other pipe thread compound
which help seal plumbing connections.
3 twist-on wire connectors for 16 AWG wire
(need to have metal inserts).
UL listed conduit connector or strain relief .
www.boschappliances.com
ENGLISH - 3
MATERIALS SUPPLIED
Accessory Parts Supplied
Accessory Parts for your model dishwasher
will come in one or more plastic bags. Check
to make sure that the parts supplied for your
model are all there. See Figure 3. If any
parts are missing, stop the installation and
contact your dealer immediately.
DISHWASHER
INSTALLATION KIT (Clear Bag)
D. Toe Panel Screws (8mm) (2)
E. Mounting Brackets (1L & 1R)
F. Mounting Bracket Screws (2)
G. Rubber Connection Hose (1)
and Drain Hose Clamps (2)
SHU 9910, 9920, 8800
and 8810 Models
(excluding 9950 models)
• Dishwasher Installation Kit (1) and
• (Yellow Bag) w/ the following:
A. Hex Wrench 4mm (1)
B. Cover Plugs (2 Wh & 2 Blk) and
R. Door Handle
SHU 6800 Models
• Dishwasher Installation Kit (1) and
• (Green Bag) w/ the following:
L. J-Box Cover (1)
M. J-Box Screw (8mm) (1)
N. Toe Panel Screw (4x16) (2)
O. Base Part Screws (M4x38) (2)
SHV and SHI Models
• Dishwasher Installation Kit and
• Outer Door Installation Kit (Blue bag):
J. SHI/SHV Panel Installation Template
C. Cap (2 Blk)
K. Wood Screws (2)
I. Mounting Door Brackets(2 plastic)
w/Screws (4) and;
Mounting Door Brackets (2 metal)
w/Screws (4)
H. Spring Tension Screw (2)
Manual Bag
All Dishwashers come with a manual bag.
The following contents are located in every
bag:
• Use & Care Manual
• Installation Instructions
P. Tall Item Sprinkler (1)
(except SHU 3030 and 3130 models)
SHU 6800 models have an additional part:
Q. Cotton Insulation Strip (1)
Note: Pictures are not to scale.
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
R
Figure 3
4 - ENGLISH
www.boschappliances.com
CHOOSING A LOCATION
23 9/16" (598 mm) min.
23 5/8" (600 mm) min.
23-5/8" - 24-1/8" (600-613 mm)
22 7/16" (570 mm) min.
THESE INSTALLATION
INSTRUCTIONS ARE
INTENDED FOR USE BY
QUALIFIED INSTALLERS
Choosing the Location
Select a location as close to the sink as
possible for ready access to water and drain
lines.
Most of the installation work is done
the dishwasher is moved into place.
Any built-in dishwasher must be fully
enclosed on the top, both sides and back.
Therefore the cabinet space below your
counter is probably the best location.
Overall Dishwasher Dimensions
AthgieH.nim)mm068("8/733
before
3-1/2” (90mm)
1-15/16” (49mm)
4” (102mm)
Figure 4
NOTE: This dimension will vary by model
due to control panel differences.
24” (610 mm)
C
ENGLISH
ENGLISHENGLISH
ENGLISHENGLISH
BhtdiW.nim)mm806("61/5132
ChtpeD.nim)mm375("61/922
Table 1 – See Figure 4
Cabinet Opening Dimensions
AthgieH.nim)mm468("43
BhtdiW.nim)mm016("42
ChtpeD.nim)mm016("42
Table 2 – See Figure 5
For proper operation and appearance of the
dishwasher, the cabinet opening should be
square and have dimensions as shown in
Figure 5.
If the dishwasher is to be installed in a
corner, make sure there is adequate clearance to open the door. See Figure 6.
90°
24” - 24-1/4” (610-616 mm)
Figure 5
Clearance
for door
opening
Door in
open
position
Figure 6
A
34” (864 mm)
B
90°
minimum
Dishwasher
Countertop
www.boschappliances.com
ENGLISH - 5
Loading...