Bosch SHE44C07UC/22, SHE44C06UC/22, SHE44C05UC/22, SHE44C02UC/22 Installation Guide

YOURLIFE.OURINSPRATJON.

Dishwasher Installation instructions instructions d'instaHation du _ave-vaisse_e

Instrucciones de insta_aci6n para _avavajiHas

Use and Care Manua_ _ocated on reverse side Tourner _eguide pour _ee instructions d'utHisation et d'entretien

Vo_tee e_manua_ para encontrar _as instruccionee de uso y cuidado

9000089901 (8506)

Tabmeof Contents / _mportant Instructions

important Safety instructions

To avoid possible injury or property damage,

OBSERVE ALLWARNmNGS AND CAUTmONS.

These instructions are intended for use by qualified installers onty.

The dishwasher must be installed by a qualified serqce technician,

, in addition to these instructions, the dishwasher

shah be installed to meet all electrical and plumbing codes and ordinances (both national and

local),

Read these installation instructions completely and follow them carefully. They will save you time and effort and help to ensure safety and optimum

If the dishwasher is installed ina location that

experiences freezing temperatures (e.g., ina

hoJiday home), you must drain aH the water

from the dishwasher's interior.Water system

ruptures that occur as a result of freezing are not covered by warranty.

IMPORTANT

* The dishwasherdrain hose must be installed

with a portion of it at least 20" (508mm) off the cabinet floor; otherwise the dishwasher may not drain properly,

* This dishwasher is intended for residential use

only, and should not be used in commercial food service establishments,

* NEW INSTALLATION - If the dishwasher is a

new installation, most of the work must be done before the dishwasher is moved into place,

* REPLACEMENT - If the dishwasher is replacing

another dishwasher, check the existing dishwasher connections for compatibility with the new dishwasher, and replace parts as necessary,

* This appliance has been found to be in

compliance with CAN/CSA-C22,2 No, 167/UL 749, It is the responsibility of the owner and the installer to determine ifadditional requirements and standards apply in specific installations,

Inspect the Dishwasher After unpacking the dishwasher and prior to installation, thoroughly inspect the dishwasher for possible freight or cosmetic damage, Report any damage immediately, Cosmetic defects must be reported within 30 days of installation, NOTE: Do not discard any bags or items that come with the original package until after the entire installation has been completed,

TOOLS NEEDED

Tooms and Matedams Needed

Hammer

Tape Measure

Hob Saw

Sbt Screwd river

PhHHpsScrewdriver

Wire Cutter Wire Stripper DrHU

MATERIALS NEEDED

(AdditionaU materiab may be required to compUywith UocaUcodes,)

%20 Screwdriver

LeveU

EbctrbaU SuppUyCabb ° Minimum #14 AWG, 2 conductor, 1 ground, insuUatedcopper

conductors rated 75°C or higher,

Hot Water Supply Line - Minimum 3/8" O,D, copper tubing or metal braided dishwasher

supply line,

Shut-off valve and fittings appropriate for hot water supply line (copper tubing/

compression fitting, or braided hose),

90° elbow with 3/8" N,RT, male threads on one leg, and sized to fit your water supply line (copper tubing/compression fitting, or braided hose) on the other leg,

Teflon tape or other pipe thread compound to seal plumbing connections,

UL listed conduit connector or strain relief,

Materials Supplied

MATEFImALS SUPPUED

Accessory Parts Supplied Accessory parts for your dishwasher come in one or more pUastb bags that are outlined bebw,

NOTE: Make sure you save aHthe bags until you have compbted your installation, NOTE: AUwaysuse the supplied or recommended hardware,

f Manual Set Bag

A ManuaUSet Bag is provided with each dishwasher and

incUudes:

A Use & Care instructions and installation

instructions (both manuab may be induded

in a singb "fHp-styb" book B Quick Reference Guide (select models) C ExtraTall Item Sprinkler ',,

D SHI and SHV Installation Template (SHI and SHV "-

models only) E White Cotton Insulation Strip (SHY66C, SHX99A,

SHE66C, SHE99C and SHX57C models only)

f Dishwasher Installation Kit

A Dishwasher Installation Kit is provided with each dishwasher and includes:

F Toe Panel Screws (2 black machine screws)

Note: These screws are included, but not used on

models with the Toe Panel Installation Kit, G CounterTop Mounting Brackets (2 %?shaped metal

brackets) H Mounting Bracket Screws (2 silver wood screws) m Rubber Drain Hose Adaptor (1 black rubber tube)

J Hose Clamps ( 1 silver spring clamp to use to

attach the rubber adaptor to the Drain Hose and 1 gold screw clamp to attach the rubber adaptor to

8 s,$

K Wire Nuts (3 for electrical connection) L Electrical Junction Box Screws (2 silver

machine screws) IV] Leg Leveler Locking Screws (2 gold coarse

f SHm/SHV Door PaneJ mnstaHation Kit

A Door Panel Installation Kit is provided with select dishwashers that use a custom wood door panel and

includes:

N Plastic Caps (2) _' _ 0 Spring Tension Screws (2 larger silver machine

screws used to adjust the door springs to accom-

modate doors of different weights)

P Door Mounting Brackets (2 gold metal brackets

and 2 white plastic brackets used to mount the custom door)

Q Door Mounting Bracket Screws (8 silver wood

screws) _ ®@ _@

R Door Mounting Screws (2 long silver screws used _ _ ........._

..............t_ a!t_£_tht_tO r).......................................................................................................................................................................................................................................

f Toe PaneJ installation Kit _'

AToe Panel Installation Kit is provided on models

SHY66C, SHX99A, SHE66C, SHE99C and SHX57C, These models have a special noise reducing Toe Panel with the following mounting hardware:

S Toe Panel Screws (2 black screws used to attach _ T Black Plastic Base Access Panel Screws (2 long

silver screws used to attach the Black plastic

23-5/8" - 24-1/4" (600-616 mm

Figure 1

23 9/16"

',598mm)

Enclosure Preparation

Electrical Shock Hazard

To avoid electrical shock, make sure the water suppJy and ebctrical suppJy are shut off before

installation or service.

ENCLOSURE PREPARATmON

NOTE: This dishwasher is designed to be enclosed on the top and both sides by standard residential kitchen cabinetry.

Select a location as close to the sink as possible for easy access to water supply and drain lines. For proper dishwasher operation and appearance, ensure that the enclosure is square and has the dimensions shown in Figure !. If the dishwasher is to be installed in a corner, make sure that there is adequate clearance to open the door. See Figure 2,

Check _ ......... -

E E

clearance E between

dishwasher , door and wall

Figure 2

Countertop

i\ I\\

ElectricaJ Shock/Fire Hazard

To avoid ebctric shock or fire, do not allow the eJectricaJ and water supply Jines to touch.

Separate channets are provided under the dishwasher (see page 10}.

if the enclosure requires openings for the electrical supply cable, hot water supply line, and dishwasher drain hose, place them within the dimensions shown by the shaded area of Figure 3 to avoid interference with the dishwasher frame or other components, Make the openings for the electrical supply cable and hot water supply line 1" (25,4mm) diameter, Make the opening for the dishwasher drain hose 1-1/4" (82mm) diameter, if the openings are made through wood, sand them smooth, if the openings are made through metal, make them large enough to accommodate grommets or other protective sheaths with inside diameters of 1" (25,4mm) for the electrical supply cable and the hot water supply line, and 1-1/4" (32mm) for

the dishwasher drain hose,

Figure 3

30 _'

(762mm)

2! EE

(533mm)

Figure 4

Dishwasher Electrical Rating

Vemts Amperes Watts

Emectrica{Preparation

ELECTRICAL PREPARATmON

ElectdcaJ Shock Hazard

To avoid electrica! shock, do not work on an energized circuit. Doing so could resuJt in serious

injury or death. OnJy quaJified eJectricians shouJd perform etectricaJ work. Do not attempt any work on the dishwasher eJectric suppJy circuit until you

are certain the circuit is de-energized.

Fire Hazard

To avoid a fire hazard, make sure eJectdcaJ work is properJy installed. OnJy qualified eJectricians shouJd perform eJectrical work.

120 60 15 1,450

(max)

(76mm- 102mm)

3/8"- 1/2" _ .<

(10mm - 13mm)

< J

Figure 5

ElectricaJ SuppJy The customer has the responsibility of ensuring that the dishwasher electrical installation is in compliance with all

national and local electrical codes and ordinances. The dishwasher is designed for an electrical supply of 120V,

60 Hz, AC, connected to a dishwasher-dedicated, properly grounded electrical circuit with a fuse or breaker rated for 15 amps. Electrical supply conductors shall be a minimum #14 AWG copper wire rated at 75°C or higher.

Regardless of where the electrical supply cable enters the enclosure, position the cable 21" (533mm) from the enclosure's left side, as shown in Figure 4. Extend the cable 30" (762mm) from the enclosure's back, as shown in Figure 4,

Remove 3" =4" (76mm =102mm) of the cable's outer casing, as shown in Figure 5, then remove 3/8" - 1/2" (10 - 13mm) of insulation from each wire, as shown in Figure 5,

+ 12 hidden pages