How it Works
Bosch
Loading...
NEM732UC/01
Installation Guide
8 pgs300.5 Kb0

Bosch NEM936UC/01, NEM935UC/01, NEM932UC/01, NEM736UC/01, NEM735UC/01 Installation Guide

...
Download
Page 1
BOSCH
Installation Instructions
sosc_
NEM73
8oscH
NEM93
,O
,O
Bosch Glass Ceramic Cooktops
Models: NEM73, NEM93
Page 2
Table of Contents
NOTE: The blocked letters, such as A, shown below, refer to illustrations on
Pages 2 & 4. Match these to the related text pages.
Overall Dimensions A ............................................................................................... 2
Power Supply B .......................................................................................................... 2
Cabinet Preparation and Clearances C ............................................................. 2, 3
Junction Box Location O ........................................................................................... 2
Countertop Cutout Dimensions IE ........................................................................ 2
Installing the Cool<top F ........................................................................................ 3-4
Secure Cool<top to Countertop G ..................................................................... 3-4
Solid Surface Countertop Installations 14 and I .................................................. 5
Electrical Connection ................................................................................................ 5
IMPORTANT: Save these instructions for Local Electrical Inspector's use.
INSTALLER: Please leave these Installation Instructions with this unit for the owner.
OWNER: Please retain these instructions for future reference.
READ AND SAVE THESE INSTRUCTIONS
OVERALL DIMENSIONS A
See Illustration A, Page2. These dimensions are overall.
POWER SUPPLY B
ELECTRICAL POWER CONNECTION FOR COOKTOP
Power Supply is dual rated: 240 Volts or 208 Volts, 3 wire, 60 Hz, with the following circuit breaker requirements: Model NEM73 at 30 Amps; Model NEM93 at 40Amps
JUNCTION BOX LOCATION D
Planthe installation of the unit so that the location of
the junction box is within 3 feet of the left rear of the
cooktop bosom. It must be accessible from the front of the cabinet.
Connect only to a 3-wire 120/240 or 120/208 volt ac system.The neutral is not required for the operation of this appliance but an independent ground is required.
Install ajunction box (not supplied), below the counter top within 3 feet of flexible conduit (supplied) located
at the left rear corner of the cooktop rough-in box.
PAGEI
Page 3
Overall Dimensions
Model NEM73:Width 30"
Model NEM93:Width 36"
All Models: Depth 21 - I/8"
Height above countertop: I/4"
Cabinet Bottom
Building Back
Wall
Wall
r_ Required supply
Power
Model NEM73:30 Amp circuit breaker
Model NEM93:40 Amp circuit breaker
All 240Volt, 3 Wire, 60 Hz
208Volt, 3Wire, 60 Hz
r_ junction Box LocationMinimum Cabinet Clearances
MODEL NO.
NEM73
NEM93
DIM.
B C B C
Cooldng Surface
CounterTop Cutout Dimensions
/"_ / _ I" Flat Area
=' ,3,4F,atA,ea
r I" Flat Area
CUTOUT
DIMENSIONS*
Minimum
Inches / (mm)
19-7/8"/(505mm)
28-3/4'' / (731 mm)
19-7/8'' / (505 mm)
34a/4'' / (883 mm)
Maximum
Inches / (mm)
20" / (508 mm) 28-7/8'' / (734 mm) 20" / (508 mm) 34-7/8'' / (886 mm)
*For solid surface countertop installations, use maximum cutout dimensions and
consult manufacture surface for specific cutting instructions.
PAGE 2
Page 4
CABINET PREPARATION AND CLEARANCES C
CAUTION
To eliminate the risk of burns or fire by reaching over
heated surface units, cabinet storage space located
above the surface units should be avoided. If cabinet
storage is to be provided, the risk can be reduced by installing a range hood that projects horizontally a
minimum of 5 in.(127 ram) beyond the bottom of the cabinets. See C, Page 2.
This unit is designed for installation in the counter top with zero clearance to adjacent walls and projecting
surfaces constructed of combustible materials.A 30- inch minimum clearance is required between the top
of the cool(top and the bottom of an unprotected cabinet. A 24-inch minimum distance is necessary when
the bottom of the wood or metal cabinet is protected
by not lessthan I/4 inch of a flame retarclant material covered with not less than No. 28 MSG sheet steel,
0.015-inch (0.4 ram) thick stainless steel, 0.024-inch (0.6 ram) aluminum, or 0.020-inch (0.5 ram) thick copper. Flame retarclant materials bear the marl(:
COUNTERTOP CUTOUT
DIMENSIONS
The cutout dimensions depend upon whether the installation is for replacement, new construction, or
installation ina solid surface countertop material,such as Surel TM, Corian ® etc.These materials require larger cutouts, use of heat reflective tape and rounded
corners. Drawings G and 14 provide some guidelines only (see Page4 and 5). Always consult the countertop manufacturer for specific installation instructions.
E
INSTALLING THE COOKTOP
WARNING:
TOAVOID ELECTRICAL SHOCK HAZARD,
BEFORE INSTALLING THE COOKTOP,
SWITCH POWER OFF AT THE SERVICE
PANEL AND LOCK THE PANEL TO PREVENT THE POWER FROM BEING
SWITCHED ON ACCIDENTALLY.
UNDERWRITERS LABORATORIES INC.
CLASSIFIED
MINERAL AND FIBER BOARDS
SURFACE BURNING CHARACTERISTICS
Followed bythe flame spread and smoke ratings,these designations are shown as "FHC (Flame Spread)/
(Smoke Developed)". Materials with"O" flame spread ratings are flame retardant. Local codes may allow other
flame spread ratings.
The minimum horizontal clearance from the sides and
back edge of the cool(top to the adjacent vertical combustible walls is zero inches.
Seal with foam tape F
A foam tape is provided to seal the cool(top edges to the countertop (see page4).Turn cool(top upside down and apply tape approximately 1/16" from the glass edges. Use tape around the entire glass perimeter cut off excess where tape ends butt.
Secure Cooktop to countertop G
The cool(top should be secured to the countertop using the hold-down brackets provided. Prior to
inserting cool(top into cutout, turn cool(top upside clown and attach brackets to the burner box using the
washers and screws.
Place cooktop into cutout. Insert clamping screws into
the brackets and secure cool(top to countertop.
Use a wood block to protect fragile countertop materials.
PAGE 3
Page 5
Foam
Tape Seal
Foam Tape Seal
Solid Surface Countertop Installation
_od block
Adjusting
Screw
_'_ Hold Down Brackets
i '
Location
of aluminum reflective tape
i Tape top and vertical sides
UtOUt
27-3/8"
3J ,4,,J
4I' Nominal I
Toe Space J
H 2x 4 Supports
Installing OverAn Oven
PAGE 4
Page 6
Solid Surface Countertops H Always consult the countertop manufacturer
for specific instructions.
Countertops made from natural (i.e. granite and marble) or SOLID SURFACE MATERIALS, such as
Surell TM and Corian ®, require special cutout preparation and installation procedures. Follow the guidelines below and on pages 2-4 for preparing the
cutout.
Install the cool<top as follows:
I. Round the cutout corners according to
instructions from the countertop manufacturer.
2. Apply heat reflective tape (such as Scotch ® Aluminum Foil Tape #425 or #427) around the
cutout so that it folds over the top and side surfaces. Be sure the tape extends beyond the outermost flange of the cooktop. All corners
should also be covered with tape.
3. Attach brackets to the burner box using washers and screws provided. Use a wooden block
underneath the countertop before tightening the bracket screws.
4. Center cooktop in the cutout to ensure adequate
clearance between the burner box and countertop edge. (A light pencil marl< along the center of front edge and side edge of cooktop and counter will
aid in the positioning of the cooktop in the center.)
ELECTRICAL CONNECTION
I. Attach flexible conduit to the junction box.
2. Connect the cooktop lead wires to the junction box supply wires in proper phase:
For all models, connect black (LI) to black,
red (L 2) to red, green wire to ground.
NOTE: If the cool<top is installed and connected as
specified above, it will be completely grounded in compliance with the National Electrical Code.
Remove everything from the cooktop surface and
apply Cooktop Cleaning Creme (packaged with cooktop) as directed in Use & Care Manual, page
10.
4. Turn on power supply.
5. Test operation.
NOTE: Your cooktop surface needs to be cleaned daily. Refer to the Use and Care section before using
it for the first time.
5. Trim excess aluminum tape from along the frame edges. BE CAREFUL not to scratch the countertop.
PAGE 5
Page 7
BEFORE CALLING FOR SERVICE
If the elements do not heat or if the indicator "on" light does not glow, check the power
source to see if a fuse has blown or if the circuit breaker has tripped.
Refer to the Cooktop Warranty on Page I I of the Use and Care Manual.
See Use and Care manual for troubleshooting information.
Product data plate
The data plate shows the model and serial number of your cooktop. It is located in the center front area of the rough-in box, underneath the cooktop.
Keep your invoice or escrow papers for warranty validation if service is needed.
PAGE 6
Page 8
Specificationsareforplanningpurposesonly. Refer to installation instructions and consult your countertop supplier prior to making
counter opening. Consult with a heating and ventilating engineer for your specific ventilation requirements. For the most detailed information, refer to Installation Instructions accompanying product or write BSH HomeAppliances Corp. indicating the model number.
We reserve the right to change specifications or design without notice. Some models are certified for use in Canada. BSH is not
responsible for products which are transported from the United States for use in Canada. Check with your local Canadian distributor or dealer.
For the most up to date critical installation dimensions by fax, use your fax handset and call 702/833-3600. Use code #8317.
Note:The Bosch cool<top referred to throughout this manual is manufactured by BSH Home Appliances Corp.
BOSCH
5551 McFadden Avenue, Huntington Beach, CA 92649 • 800/944-2904
© 2002 BSH Home Appliances Corp. • Litho U.S.A. 01/02
50 60003491 (8201)
Loading...
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use