Bosch NEI-308V05-23WE Specsheet

Video | NEI-30 Dinion IP Infrared Imager

NEI-30 Dinion IP Infrared Imager

www.boschsecurity.com

u Certified all-weather active IR surveillance camera

specifically designed for perimeter surveillance and
other outdoor low-light applications

u Dinion 2X imaging with wide dynamic capability to

handle the most demanding lighting situations

The Dinion IP Infrared Imager is a rugged, active
infrared surveillance camera designed to master
perimeter surveillance and other outdoor low-light
applications. The IR Imager provides best-in-class
images day and night covering up to 160 meters (525
feet) with unrivaled illumination quality throughout the
field of view.
The Dinion IP Infrared Imager can tri-stream video
simultaneously — on two H.264 streams and one M­JPEG stream. Features such as multicasting, internet
streaming, and iSCSI recording are fully supported.
The Dinion IP Infrared Imagers have built-in video
motion detection and video content analysis systems
as standard features.
From the most challenging daylight conditions to zero
lux night environments, the NEI-30 gives you the
details you need. Our Dinion 2X technology provides
optimal 20-bit imaging in natural and artificial light,
giving you a powerful wide dynamic range camera
solution capable of handling the most demanding
lighting situations, 24 hours a day.
Variable Field Illumination allows IR beam pattern
adjustments in the field, allowing for wide area
coverage and greatly reducing maintenance and setup

u Variable Field Illumination technology provides

unmatched low-light and no-light performance

u Integrated junction box, remote control, and

complete external adjustments minimize installation
time and cost

u Tri-streaming: Dual H.264 and M-JPEG

simultaneously

time and effort. Variable Field Illumination also
provides even illumination not only across the field of
view but also from foreground to background. To
ensure this performance never fades over time, the IR
Imager features Constant Light technology, using
closed loop feedback to control infrared performance
throughout the life of the unit.
The IP67-rated junction box and the camera can be
hung and connected in seconds, reducing time and
energy on the ladder. The IP-based control further
reduces time needed for adjustments during and after
installation by allowing for adjustments to be made
remotely on the ground.

System overview

Efficient bandwidth and storage management

The Dinion IP Infrared Imager uses H.264
compression, bandwidth throttling, and multicasting
capabilities to manage bandwidth and storage
requirements efficiently, while delivering high-quality
images and resolution. The bandwidth of an H.264
stream using Main profile at 4CIF resolution is about
the same as one MPEG-4 stream at 2CIF resolution.
Bosch's innovative tri-streaming feature enables the

| NEI-30 Dinion IP Infrared Imager

2

imager to generate two independent H.264 streams
and one M-JPEG stream simultaneously. This allows
streaming of high-quality H.264 images for live viewing
and recording while streaming M-JPEG images to
another device at the same time. The M-JPEG video
stream also provides easy integration with third-party
JPEG or M-JPEG-compatible video management
systems.
The Dinion IP Infrared Imagers offer unparalleled
recording options. Attached to the network, they can
use iSCSI targets directly, as well as Network Video
Recorders (NVRs). The iSCSI storage target support
enables the cameras to function as a conventional
DVR, while streaming high-performance live video
across the network.

Standard intelligence

With built-in video content analysis, the imager
reinforces the Intelligence-at-the-Edge concept where
edge devices become increasingly intelligent. The
MOTION+ video motion analysis system that is built
into all camera versions is the perfect solution for
applications where basic video content analysis
features are required. This motion analysis algorithm is
based on pixel change and includes object size
filtering capabilities and sophisticated tamper­detection capabilities.
The NEI-30 also features the more advanced Intelligent
Video Analysis (IVA) standard on all models. The pre­installed IVA digital imaging technology algorithm uses
multi-level image analysis of pixels, texture, and object
direction.

ONVIF conformance

The Dinion IP Infrared Imager conforms to the ONVIF
(Open Network Video Interface Forum) specification
which guarantees interoperability between network
video products regardless of manufacturer. ONVIF
conformant devices are able to exchange live video,
audio, metadata and control information. They are
automatically discovered and connected to network
applications such as video management systems.

Power over Ethernet

Power may be supplied via a Power over Ethernet Plus
(PoE+, IEEE 802.3at, class 4) compliant network cable
connection. With this configuration, only a single cable
connection is required to power and to control the
camera while also viewing images from the camera.
(Note: PoE+ power limitations reduce the IR range and
low temperature range.)

Unsurpassed flexibility

There are many ways to access the imager’s video: on
a PC using a web browser, with the Bosch Video
Management System, or with VIDOS. The camera is
also ideal for use with a DHR/DNR 700 Series digital
video recorder. By routing a video stream to a Bosch
video decoder, you can also present the video with
ultimate clarity on an analog monitor.

Functions

DCRI Zero Lux Performance

850 nm 940 nm

Range Horizontal

Field of

Illumination

Detection 160 m

(525 ft)

Classification120 m

(390 ft)

Recognition90 m

(295 ft)

Identification50 m

(165 ft)

28 m

(90 ft)

21 m

(70 ft)

16 m

(50 ft)

9 m

(30 ft)

Range Horizontal

Field of

Illumination

80 m

(260 ft)

60 m

(195 ft)

45 m

(150 ft)

25 m

(80 ft)

14 m

(45 ft)

10 m

(35 ft)

8 m

(25 ft)

4 m

(15 ft)

Note: DCRI values given are with narrow IR beam
configuration and with a dedicated power input. Units
powered via PoE+ have reduced range at maximum
focal length.

Dinion Integrated Imaging – reveal every detail

• More detail in difficult lighting featuring superior
120dB (20-bit image processing) wide dynamic range

• 24/7 performance around the clock with 2X image
processing that dynamically adapts to scene changes
in addition to infrared illumination compensation

High Performance Illumination

• Variable Field Illumination allows user-selectable
coverage for even illumination across the field of view
and from foreground to background

• Constant Light technology ensures consistent imaging
throughout the life of the product

• 850 nm and 940 nm infrared wavelength options

Installer-Friendly Features

• Junction box can be preinstalled to minimize time “on
the ladder”

• Integrated on-screen display (OSD), complete
external adjustments, and IP-based control reduces
service and installation time

Ready for All Environments

• IP67 – dust proof and protection against temporary
submersion

• NEMA4X – all weather rated and corrosion resistant

• EN60068-2-6 – shock and vibration tested

• IK10 – impact resistant (except for window)

• MIL-STD-810F2 – tested to operate in conditions
exceeding A1 environments (harshest desert
classification) for exposure to solar radiation

1. The camera is designed to be installed on static structures using the specified mounting

adapters. It should not be installed in dynamic environments or on moving objects such as

vehicles, ships or elevators.

2. Long term continuous exposure in worst case conditions can impact component life.

1

3 | NEI-30 Dinion IP Infrared Imager

Certifications and approvals

Region Classification

Europe CE (Declaration of Conformity)

USA UL, FCC

Canada CSA

Australia C-Tick

Electromagnetic Compatibility

Emission EN55022 class B, FCC part 15 class B,

EN6100-3, IC ICES-03

Immunity EN50130-4 (CE), EN6100-6-3 (CE)

Safety

UL60065-07, CAN/CSA 60065-03, EN60065 (CE)

Environmental

Weatherproofing IP67, Type 4X (NEMA 4X), CSA 22.2 No. 94-

M91, UL 50

Impact Resistance IK10 (except window)

Solar Radiation Tested for MIL-STD-810F (for A1 environments)

Installation/configuration notes

Canting Directions

Camera Rotated 90° Right, Tilted 48° Down

Use Cases

1 Horizontal Angle (H)

2 Vertical Angle (V)

3 Horizontal Field of Illumination (HFOI) /

Horizontal Field of View (HFOV)

4 Depth of Field (DoF) Range

5 Distance

General Area Surveillance: RECOGNITION

IR Beam Pattern
(Full Width Half Maximum)

Camera Focal Length; FOV

2

2

43° x 20°

6 mm focal length; 44° x 33°

Camera Rotated 90° Left, Tilted 44° Up

DoF Range 5–23 m (16–75 ft)

3

HFOI

HFOV

3

17 m (56 ft)

17 m (56 ft)

Critical Asset and Entry/Exit Monitoring:
RECOGNITION

IR Beam Pattern
(Full Width Half Maximum)

Camera Focal Length; FOV

2

2

10° x 10°

24 mm focal length; 11° x 9°

DoF Range 23–90 m (75–300 ft)

4 | NEI-30 Dinion IP Infrared Imager

3

HFOI

HFOV

3

16 m (53 ft)

17 m (56 ft)

4CIF 704 x 576/480 (25/30 ips)

CIF 352 x 288/240 (25/30 ips)

Perimeter Monitoring (100 m/330 ft zone spacing):
RECOGNITION/CLASSIFICATION

IR Beam Pattern
(Full Width Half Maximum)

Camera Focal Length; FOV

2

2

10° x 10°

20 mm focal length; 14° x 10°

DoF Range 20–120 m (65–400 ft)

3

HFOI

3

HFOV

2. Measurements are H x V.

3. At maximum range.

21 m (69 ft)

29 m (95 ft)

Parts included

Quant. Component

1 NEI-30 Dinion IP Infrared Imager

1 Cable-managed pan/tilt bracket

1 Junction box

1 Sunshield

1 Installation kit

Technical specifications

Electrical

Overall IP Delay Min. 120 ms, Max. 240 ms

GOP structure I, IP

Frame rate 1 to 50/60 (PAL/NTSC) H.264

1 to 25/30 (PAL/NTSC) M-JPEG

Video Out

Signal Analog composite (NTSC or PAL), for use

with OSD menus only

4

Connector BNC, 75 Ohm

Horizontal resolution 540 TVL

Video S/N 50 dB

4. The analog video output is active only when interacting with the imager’s OSD menus. Note that when analog video

output is active, the IP video output is interrupted.

Sensitivity (3200 K, scene reflectivity 89%, F1.2)

Full video

(100 IRE)

Usable
picture

Usable picture
(30 IRE)

(50 IRE)

Color 2.4 lx

(0.223 fc)

Color
+ SensUp 10x

0.24 lx
(0.0223 fc)

0.47 lx
(0.044 fc)

0.047 lx
(0.0044 fc)

0.15 lx
(0.0139 fc)

0.015 lx
(0.0014 fc)

Rated Voltage 12 VDC (± 10%),

24 VAC (± 10%), 50/60 Hz,
Power over Ethernet +

Power Consumption

• at 12 VDC 35 W (2.9 A)

• at 24 VAC 35 W (1.5 A)

Sensor

CCD Type 1/3-in. interline, WDR dual shutter

Active Pixels: PAL: 752 x 582

NTSC: 768 x 494

Video

Video compression H.264 (ISO/IEC 14496-10); M-JPEG,

JPEG

Data rate 9.6 Kbps to 6 Mbps

Resolution Horizontal x vertical (PAL/NTSC ips)

Monochrome 0.98 lx

(0.091 fc)

Monochrome
+ SensUp 10x

Monochrome
+ IR

0.098 lx
(0.0091 fc)

0 lx
(0 fc)

0.188 lx
(0.0174 fc)

0.019 lx
(0.0017 fc)

0 lx
(0 fc)

0.06 lx
(0.0056 fc)

0.006 lx
(0.0006 fc)

0 lx
(0 fc)

Illumination

Interfaces

Power

• PoE+ RJ-45 100 Base-TX Ethernet PoE+ IEEE

802.3at, class 4

• Imager 12 VDC/24 VAC (± 10%),
50/60 Hz

Analog (video) PAL or NTSC BNC, for use with OSD

menus only

5

Video and Control STP, 10/100 Base-T, auto-sensing, half/

full duplex, RJ45

On-screen Display OSD with soft-key operation (multilingual)

| NEI-30 Dinion IP Infrared Imager

5

Alarm Output Relay 30 VAC or +40 VDC, max. 0.5 A

continuous, 10 VA
Tamper: Open/close, normally closed
voltage free relay

5. The analog video output is active only when interacting with the imager’s OSD menus. Note that when analog video

output is active, the IP video output is interrupted.

Video

Horizontal Resolution 540 TVL

Signal-to-Noise Ratio >50 dB

Shutter Auto (1/50 [1/60] to 1/10000)

selectable
Auto (1/50 [1/60] to 1/50000) automatic
flickerless, fixed selectable

Sensitivity up Adjustable from Off up to 10x

Day/Night Color, Mono, Auto Video, Auto Photocell

Day/Night Photocell
Control

Day/Night switch adjustable:
25 lux to 64 lux (default at 48 lux)
Night/Day switch adjustable:
43 lux to 82 lux (default at 63 lux)

Auto Black Automatic continuous, Off

Dynamic engine XF-Dynamic, 2X-Dynamic, SmartBLC

Dynamic range 120 dB (20-bit image processing)

Video Motion Detection One area, fully programmable

Privacy Masking Four independent areas, fully

programmable

Network

Protocols RTP, Telnet, UDP, TCP, IP, HTTP, HTTPS,

FTP, DHCP, IGMP V2/V3, ICMP, ARP,
SMTP, SNTP, SNMP, 802.1x, UPnP

Encryption TLS 1.0, SSL, AES (optional)

Ethernet STP, 10/100 Base-T, auto-sensing, half/

full duplex, RJ45

PoE+ supply IEEE 802.3at, class 4

Software Control

Unit Configuration Via web browser or Configuration Manager

Flicker Control 50/60 Hz, selectable

Software update Flash ROM, remote programmable

Illuminator Specifications

LEDs 7 SMT type LED array with Variable Field

Illumination

Beam Patterns
(H x V)

Wide beam: 42° x 10° (with 3D diffuser)
Narrow beam: 10° x 10°

Dynamic Noise

Auto, On/off selectable

Reduction

Sharpness Sharpness enhancement level selectable

SmartBLC On (includes 2X-Dynamic ) / Off

AGC AGC On or Off (0–30 dB) selectable

Peak White Invert On/Off

White Balance ATW, ATWhold and manual (2500 to

10000K)

Alarm Output VMD or D/N and dedicated Tamper (for

junction box)

Cable Compensation Up to 1000 m (3000 ft) coax without

external amplifiers (automatic set-up in
combination with Bilinx coaxial
communication)

Camera ID 17 character editable string, position

selectable

Test Pattern Generator Color bars 100%, Grayscale 11-step,

Sawtooth 2H, Checker board, Cross
hatch, UV plane

Lens 5–50 mm IR-corrected Varifocal auto-iris

Angular Field of View
(H x V)

5 mm FOV: 51° x 40°
50 mm FOV: 6° x 4°

Wavelength 850 nm or 940 nm

Intensity Adjustment 31 step adjustments from min. to max.

On/Off Control Slave to camera mode

Manual on/off control via OSD and IP
Interface

Illumination Tilt
Adjustment

Maximum: 13° tilt above camera axis
Minimum: 3° tilt above camera axis

IR Performance Ranges (0 Lux Environment)

(with dedicated power input)

850 nm 940 nm

Range HFOI Range HFOI

Detection 160 m

(525 ft)

Classificatio
n

120 m

(390 ft)

Recognition 90 m

(295 ft)

Identification 50 m

(165 ft)

DCRI values are narrow IR beam configuration at max. focal length.

28 m

(90 ft)

21 m

(70 ft)

16 m

(50 ft)

9 m

(30 ft)

80 m

(260 ft)

60 m

(195 ft)

45 m

(150 ft)

25 m

(80 ft)

14 m

(45 ft)

10 m

(35 ft)

8 m

(25 ft)

4 m

(15 ft)

Modes 6 preset programmable modes

6 | NEI-30 Dinion IP Infrared Imager

IR Performance Ranges (0 Lux Environment)

(with PoE+ power input)

850 nm 940 nm

Range HFOI Range HFOI

Detection 140 m

(455 ft)

Classificatio
n

105 m

(340 ft)

Recognition 80 m

(255 ft)

Identification 45 m

(140 ft)

DCRI values are narrow IR beam configuration at max. focal length.

24 m

(80 ft)

18 m

(60 ft)

14 m

(45 ft)

8 m

(25 ft)

70 m

(230 ft)

52 m

(170 ft)

40 m

(130 ft)

22 m

(70 ft)

12 m

(40 ft)

9 m

(30 ft)

7 m

(20 ft)

4 m

(10 ft)

Mechanical

Dimensions (H x W x L)

• Camera and
Bracket

402 x 193 x 309 mm
(15.8 x 7.6 x 12.2 in.)

Storage Humidity up to 100%

Weatherproofing Type 4X (NEMA 4X) and IP67

Solar Radiation Tested to MIL-STD-810F test standard

for solar radiation (for A1 rated
environments)

6. Warm-up period required for cold start at –40°C (–40°F).

• Total Assembly 402 x 193 x 406 mm

(15.8 x 7.6 x 16.0 in.)

Weight

• Camera without

6.6 kg (14.5 lb)

Junction Box

• Junction Box 1.4 kg (3.1 lb)

Construction Corrosion-resistant aluminum

Color RAL 9010 pure white with RAL 9005 jet

black detail

Finish Wet paint

Window 3.3-mm (1/8-in.) thick glass

Bracket Corrosion-resistant, cable-managed

Bracket Pan/Tilt Range Pan: ±90°

Tilt: -48°/+44°

Junction Box Separate from bracket allowing for wiring

and cabling prior to camera installation

Environmental

Operating Temperature

• Standard

• With PoE+ Input

6

–40°C to +50°C (–40°F to 122°F)

6

–20°C to +50°C (–4°F to 122°F)

Storage Temperature –40°C to +70°C (–40°F to 158°F)

Operating Humidity 20% to 100% (condensing)

6.82

173.3

15.87

403.2

9.72

247.0

8.52

216.4

4.13

105.0

7.23

R183.7

6.69

170.0

6.13

155.6

7.59

192.8

12.17

309.0

15.98

406.0

6.97

R177.1

6.30

160.0

5.30

134.6

14.47

367.6

[ in.]

mm

7 | NEI-30 Dinion IP Infrared Imager

Dimensions

VEI-30 Dimensional Views

1 Top 3 Side

2 Front 4 Rear

21.82

554.2

15.89

403.7

5.83

148.2

0.65

16.5

8.00

203.2

9.30

236.1

6.50

165.1

8.55

217.2

5.2

5

133.4

5.25

133

.4

1.50

38.1

18.21

462.6

1.50

38.1

7.15

181.6

7.55

191.7

14.97

380.3

1.42

36.1

2.23

56.6

6.89

175

7.40

188

[ in.]

mm

8 | NEI-30 Dinion IP Infrared Imager

VEI-30 Dimensional Views – Mounts

1 Corner Mount - Top 3 Pole Mount - Top

2 Corner Mount - Side 4 Pole Mount - Side

Ordering information

NEI-308V05-13WE Dinion IP Infrared Imager with IVA,
850 nm, PAL

Dinion IP 2X imaging with IVA, 850 nm, 3D diffuser and
Constant Light illumination, PAL, white

Order number NEI-308V05-13WE

NEI-308V05-23WE Dinion IP Infrared Imager with IVA,
850 nm, NTSC

Dinion IP 2X imaging with IVA, 850 nm, 3D diffuser and
Constant Light illumination, NTSC, white

Order number NEI-308V05-23WE

NEI-309V05-13WE Dinion IP Infrared Imager with IVA,
940 nm, PAL

Dinion IP 2X imaging with IVA, 940 nm, 3D diffuser and
Constant Light illumination, PAL, white

Order number NEI-309V05-13WE

NEI-309V05-23WE Dinion IP Infrared Imager with IVA,
940 nm, NTSC

Dinion IP 2X imaging with IVA, 940 nm, 3D diffuser and
Constant Light illumination, NTSC, white

Order number NEI-309V05-23WE

Accessories

UPA-2450-60 Power Supply, 120 V, 60 Hz

Indoor, 120 VAC, 60 Hz In; 24 VAC, 50 VA Out

Order number UPA-2450-60

UPA-2450-50 Power Supply, 220 V, 50 Hz

Indoor, 220 VAC, 50 Hz In; 24 VAC, 50 VA Out

Order number UPA-2450-50

VG4-A-9541 Pole Mount Adapter

Pole mount adapter for an AUTODOME pendant arm or
a DINION imager, designed for poles with a diameter
of 100‑380 mm (4‑15 in.), white

Order number VG4-A-9541

VG4-A-9542 Corner Mount Adapter

Corner mount adapter for an AUTODOME pendant arm
or a DINION imager

Order number VG4-A-9542

9 | NEI-30 Dinion IP Infrared Imager

Represented by:

Americas: Europe, Middle East, Africa: Asia-Pacific: China: America Latina:

Bosch Security Systems, Inc.
130 Perinton Parkway
Fairport, New York, 14450, USA
Phone: [phone]
Fax: [phone]
[e-mail]
www.boschsecurity.us

Bosch Security Systems B.V.
P.O. Box 80002
5617 BA Eindhoven, The Netherlands
Phone: + 31 40 2577 284
Fax: [phone]
[e-mail]
www.boschsecurity.com

Robert Bosch (SEA) Pte Ltd, Security
Systems
11 Bishan Street 21
Singapore 573943
Phone: [phone]
Fax: [phone]
[e-mail]
www.boschsecurity.asia

Bosch (Shanghai) Security Systems Ltd.
203 Building, No. 333 Fuquan Road
North IBP
Changning District, Shanghai
200335 China
Phone [phone]
Fax: [phone]
www.boschsecurity.com.cn

Robert Bosch Ltda Security Systems Division
Via Anhanguera, Km 98
CEP 13065-900
Campinas, Sao Paulo, Brazil
Phone: [phone]
Fax: [phone]
[e-mail]
www.boschsecurity.com

© Bosch Security Systems 2015 | Data subject to change without notice
2233040139 | en, V4, 10. Nov 2015

VG4-SBOX-COVER Cover for Power Supply Box

Spare cover for AutoDome power supply boxes and for
the VEI-30 and NEI-30 junction boxes

Order number VG4-SBOX-COVER