Bosch AUTODOME IP 4000i, NDP-4502-Z12, NDP-4502-Z12C, AUTODOME IP starlight 5000i, NDP-5512-Z30C Installation Manual

AUTODOME IP 4000i

NDP-4502-Z12 │ NDP-4502-Z12C

en

Installation Manual

AUTODOME IP 4000i Table of contents | en 3

Bosch Security Systems Installation Manual 2017.08 | 1.0 | F.01U.xxx.xxx

Table of contents

1

Safety 4

1.1 About this Manual 4

1.2 Legal Information 4

1.3 Safety Precautions 4

1.4 Important Safety Instructions 5

1.5 Safety Addendum 6

1.6 Important Notices 6

1.7 Customer Support and Service 8

2

Unpacking 9

3

Product Description 10

4

Mounting Accessories 11

5

Preparing Wiring 12

6

Preparing the Camera 13

7

Installing a microSD card (optional) 15

8

Installing a Surface Mount and Camera 17

8.1 Tools Required 17

8.2 Installation Requirements 17

8.3 Preparing the Surface Mount for Installation 17

8.4 Installing the Surface Mount Adapter 17

9

Installing an In-ceiling Camera in a Suspended Ceiling 20

9.1 Tools Required 20

9.2 Installation Requirements 20

9.3 Preparing the Suspension Ceiling for Installation 20

9.4 Securing the Camera to the Ceiling 21

10

Installing an In-Ceiling Camera in a Drywall Ceiling 24

10.1 Tools Required 24

10.2 Installation Requirements 24

10.3 Preparing the Ceiling for Installation 24

10.4 Securing the Camera to the Ceiling 25

11

Installing a Camera Directly to an Indoor Wall 28

11.1 Installation Requirements 28

11.2 Preparing the Wall for Installation 28

11.3 Installing the Wall Mount 28

11.4 Attaching the Camera to the Pendant Interface Plate 28

12

Installing a Surveillance Cabinet and Camera 32

12.1 Installing the Wall Mount 32

12.2 Attaching the Camera to the Pendant Interface Plate 32

13

Installing a Pipe Mount and Camera 35

13.1 Tools Required 35

13.2 Installation Requirements 35

13.3 Preparing the Ceiling for Installation 35

13.4 Installing the Pipe Mount 35

13.5 Attaching the Camera to the Pendant Interface Plate 36

14

Connection 39

15

Maintenance 41

16

Decommissioning 42

16.1 Transfer 42

16.2 Disposal 42

4 en | Safety AUTODOME IP 4000i

2017.08 | 1.0 | F.01U.xxx.xxx Installation Manual Bosch Security Systems

1 Safety

1.1 About this Manual

This manual has been compiled with great care and the information it contains has been
thoroughly verified. The text was complete and correct at the time of printing. Because of the
ongoing development of products, the content of the manual may change without notice.
Bosch Security Systems accepts no liability for damage resulting directly or indirectly from
faults, incompleteness, or discrepancies between the manual and the product described.

1.2 Legal Information

Copyright

This manual is the intellectual property of Bosch Security Systems, Inc. and is protected by
copyright. All rights reserved.

Trademarks

All hardware and software product names used in this document are likely to be registered
trademarks and must be treated accordingly.

1.3 Safety Precautions

In this manual, the following symbols and notations are used to draw attention to special
situations:

Danger!

High risk: This symbol indicates an imminently hazardous situation such as “Dangerous
Voltage” inside the product. If not avoided, this will result in an electrical shock, serious
bodily injury, or death.

!

Warning!

Medium risk: Indicates a potentially hazardous situation. If not avoided, this may result in
minor or moderate injury.

!

Caution!

Low risk: Indicates a potentially hazardous situation. If not avoided, this may result in
property damage or risk of damage to the unit.

Notice!

This symbol indicates information or a company policy that relates directly or indirectly to the
safety of personnel or protection of property.

AUTODOME IP 4000i Safety | en 5

Bosch Security Systems Installation Manual 2017.08 | 1.0 | F.01U.xxx.xxx

1.4 Important Safety Instructions

Read, follow, and retain for future reference all of the following safety instructions. Follow all
warnings before operating the device.

1. Clean only with a dry cloth. Do not use liquid cleaners or aerosol cleaners.

2. Do not install device near any heat sources such as radiators, heaters, stoves, or other
equipment (including amplifiers) that produce heat.

3. Never spill liquid of any kind on the device.

4. Take precautions to protect the device from power and lightning surges.

5. Adjust only those controls specified in the operating instructions.

6. Operate the device only from the type of power source indicated on the label.

7. Unless qualified, do not attempt to service a damaged device yourself. Refer all servicing
to qualified service personnel.

8. Install in accordance with the manufacturer's instructions in accordance with applicable
local codes.

9. Use only attachments/accessories specified by the manufacturer.

10. Protect all connection cables from possible damage, particularly at connection points.

!

Caution!

Installation must be made by qualified personnel and conform to ANSI/NFPA 70 (the National
Electrical Code® (NEC)), Canadian Electrical Code, Part I (also called CE Code or CSA C22.1),
and all applicable local codes. Bosch Security Systems, Inc. accepts no liability for any
damages or losses caused by incorrect or improper installation.

All-pole power switch - Incorporate an all-pole power switch, with a contact separation of at
least 3mm, into the electrical installation of the building. If it is needed to open the housing,
use this all-pole switch as the main disconnect device for switching off the voltage to the unit.
Camera signal - Protect the cable with a primary protector if the camera signal is beyond 140
feet, in accordance with NEC800 (CEC Section 60).
Fuse rating - For security protection of the device, the branch circuit protection must be
secured with a maximum fuse rating of 16A. This must be in accordance with NEC800 (CEC
Section 60).
Outdoor signals - The installation for outdoor signals, especially regarding clearance from
power and lightning conductors and transient protection, must be in accordance with NEC725
and NEC800 (CEC Rule 16-224 and CEC Section 60).
Power disconnect - Units have power supplied whenever the power cord is inserted into the
power source, or when High Power-over-Ethernet (High PoE) power is provided over the
Ethernet CAT 5E/6 cable. The power cord is the main power disconnect device for switching
off the voltage for all units. When High PoE or PoE+ (820.3at) is used to power the unit, the
power is provided over the Ethernet cable, which is then the main power disconnect device
for switching off the voltage for all units.
Video loss - Video loss is inherent to digital video recording; therefore, Bosch Security
Systems cannot be held liable for any damage that results from missing video information.
To minimize the risk of losing information, we recommend multiple, redundant recording
systems, and a procedure to back up all analog and digital information.

!

Caution!

Always securely tighten all fittings to ensure a liquid-tight seal. Failure to do so could allow
water to enter the housing and damage the units. If a sealant is used, ensure that it is a
neutral cure type. Sealants that release acetic acid may harm electronics. Use drip loops on
the wiring outside the housing.

6 en | Safety AUTODOME IP 4000i

2017.08 | 1.0 | F.01U.xxx.xxx Installation Manual Bosch Security Systems

Always use Teflon tape and sealant on connector threads of any mount (sold separately by
Bosch or user-supplied).

1.5 Safety Addendum

Notice!

Risk of water ingress
Securely seal all fittings and connection points between the device and all mounts to ensure a
liquid-tight seal. Failure to do so could allow water to enter the housing and damage the
device. Always use Teflon tape and sealant on connector threads of any mount (sold
separately by Bosch or user-supplied).
If a sealant is used, ensure that it is a neutral cure type. Sealants that release acetic acid may
harm electronics.
Use drip loops on the wiring outside the housing.

1.6 Important Notices

Indoor use only - The product shall only be used indoors. Ethernet network should be

connected to a network environment, which must comply with the following conditions:

1.1 The function of the ITE being investigated to IEC 60950-1 is considered not likely to
require connection to an Ethernet network with outside plant routing, including a campus
environment.

1.2 The ITE is to be connected only to PoE networks without routing to the outside plant.

UL Disclaimer

Underwriter Laboratories Inc. ("UL") has not tested the performance or reliability of the
security or signaling aspects of this product. UL has only tested fire, shock and/or casualty
hazards as outlined in Standard(s) for Safety for Information Technology Equipment, UL
60950-1 . UL Certification does not cover the performance or reliability of the security or
signaling aspects of this product.
UL MAKES NO REPRESENTATIONS, WARRANTIES, OR CERTIFICATIONS WHATSOEVER
REGARDING THE PERFORMANCE OR RELIABILITY OF ANY SECURITY OR SIGNALING-RELATED
FUNCTIONS OF THIS PRODUCT.

Notice!

This is a class B product. In a domestic environment, this product may cause radio
interference, in which case the user may be required to take adequate measures.

FCC & ICES Information

(U.S.A. and Canadian Models Only)

This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules and ICES-003 of Industry Canada. These limits
are designed to provide reasonable protection against harmful interference when the
equipment is operated in a residential installation. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. However, there
is no guarantee that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and the receiver.

AUTODOME IP 4000i Safety | en 7

Bosch Security Systems Installation Manual 2017.08 | 1.0 | F.01U.xxx.xxx

– Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

– Consult the dealer or an experienced radio/TV technician for help.
Intentional or unintentional modifications, not expressly approved by the party responsible for
compliance, shall not be made. Any such modifications could void the user's authority to
operate the equipment. If necessary, the user should consult the dealer or an experienced
radio/television technician for corrective action.
The user may find the following booklet, prepared by the Federal Communications
Commission, helpful: How to Identify and Resolve Radio-TV Interference Problems. This
booklet is available from the U.S. Government Printing Office, Washington, DC 20402, Stock
No. 004-000-00345-4.

8 en | Safety AUTODOME IP 4000i

2017.08 | 1.0 | F.01U.xxx.xxx Installation Manual Bosch Security Systems

1.7 Customer Support and Service

If this unit needs service, contact the nearest Bosch Security Systems Service Center for
authorization to return and shipping instructions.

Service Centers
USA

Telephone: [phone] or 585-340-4162
Fax: [phone]
Email: [e-mail]

Customer Service

Telephone: [phone]
Fax: [phone]
Email: [e-mail]

Technical Support

Telephone: [phone]
Fax: [phone] or 717-735-6560
Email: [e-mail]

Repair Center

Telephone: [phone]
Fax: [phone] or 717-735-6561
Email: [e-mail]

Canada

Telephone: [phone]
Fax: [phone]

Europe, Middle East & Africa Region

Please contact your local distributor or Bosch sales office. Use this link:

http://www.boschsecurity.com/startpage/html/europe.htm

Asia Pacific Region

Please contact your local distributor or Bosch sales office. Use this link:

http://www.boschsecurity.com/startpage/html/asia_pacific.htm

More Information

For more information please contact the nearest Bosch Security Systems location or visit
www.boschsecurity.com

AUTODOME IP 4000i Unpacking | en 9

Bosch Security Systems Installation Manual 2017.08 | 1.0 | F.01U.xxx.xxx

2 Unpacking

– This equipment should be unpacked and handled with care. Check the exterior of the

packaging for visible damage. If an item appears to have been damaged in shipment,
notify the shipper immediately.

– Verify that all the parts listed in the Parts List below are included. If any items are

missing, notify your Bosch Security Systems Sales or Customer Service Representative.

– Do not use this product if any component appears to be damaged. Please contact Bosch

Security Systems in the event of damaged goods.

– The original packing carton is the safest container in which to transport the unit and must

be used if returning the unit for service. Save it for possible future use.

Quantity Component

1 AUTODOME IP 4000i camera

1 Camera mounting plate

1 Screwdriver, T10 Torx

1 Screwdriver, T15 Torx

4 MAC address labels

1 Quick Installation Guide

1 Safety instructions

1 Technical description (EAC)

Quantity Component

1 AUTODOME IP 4000i camera

1 Mounting template

1 Screwdriver, T10 Torx

4 MAC address labels

1 Quick Installation Guide

1 Safety instructions

1 Technical description (EAC)

10 en | Product Description AUTODOME IP 4000i

2017.08 | 1.0 | F.01U.xxx.xxx Installation Manual Bosch Security Systems

3 Product Description

The AUTODOME IP 4000i is a compact, indoor PTZ dome camera with a high-resolution
1080p60 HD sensor and a 12x optical zoom that allows operators to monitor wide scenes
without losing any details. The camera’s aesthetic design and flexible mounting options allow
unobtrusive surveillance of large halls, reception areas, or waiting areas that would otherwise
require multiple cameras for effective surveillance.

AUTODOME IP 4000i Mounting Accessories | en 11

Bosch Security Systems Installation Manual 2017.08 | 1.0 | F.01U.xxx.xxx

4 Mounting Accessories

Model Number Description Installation Location

NDA-U-WMT Pendant wall mount Indoor walls (direct installation)

Outdoor walls (onto NDA-U-PAx or
NDA-U-WMP)

NDA-U-PA0
NDA-U-PA1
NDA-U-PA2

Surveillance cabinet
(24VAC, 120VAC, or 230VAC)

Indoor/outdoor walls

NDA-U-CMT Corner mount adapter Corner of a building

NDA-U-PMAL Pole mount adapter (large) Poles that support surveillance

cameras

NDA-U-WMP Mount plate for wall mount, corner

mount, or pole mount

Indoor/outdoor walls

NDA-4020-PIP Pendant interface plate to mount

camera to NDA-U-WMT or to NDA­U-PMT

Between camera and wall mount or
pipe mount

NEZ-A4-SMB Surface mount box Indoor hard-ceilings

NDA-U-PSMB Surface mount box (SMB) for wall

mount or pipe mount

Indoor walls

NDA-U-PMT Pendant pipe mount Indoor high ceilings

NDA-U-PMTE Pendant pipe mount extension Indoor high ceilings

VGA-IC-SP In-ceiling support kit Indoor suspended ceilings

NDA-4020-PLEN Plenum box Plenum spaces in indoor

suspended ceilings

12 en | Preparing Wiring AUTODOME IP 4000i

2017.08 | 1.0 | F.01U.xxx.xxx Installation Manual Bosch Security Systems

5 Preparing Wiring

4 Prepare and install all wiring for 24 VAC, PoE+ (Cat5e/Cat6), alarms, and audio as

necessary. For 24 VAC, follow the recommendations for maximum cable distance and
wire gage.

Maximum cable distance in meters (feet) per minimum cable diameter

The following table identifies the recommended transmission distance (maximum) in meters
(feet), based on the specified wattage, per the minimum cable diameter (in mm²), when the
cable diameter is fixed and the maximum permitted power consumption for 24 VAC is 10%.
For example, for a device of 20 W and a minimum cable diameter of 1.0 mm², the
recommended transmission distance is 42 m (141 feet) from the transformer.

Models Watts 1.0 mm² 1.5 mm² 2.5 mm² 4.0 mm²

Indoor
(ceiling)

20 42 m (141 ft) 68 m (225 ft) 109 m (358 ft) 275 m (905 ft)

Outdoor 30 28 m (94 ft) 45 m (150 ft) 72 m (238 ft) 183 m (603 ft)

Wire Gage

Note: Metric wire sizes are standard DIN sizes, ISO6722, mm².

Wire diameter (mm²) AWG

1.0 18

1.5 16

2.5 14

4.0 12

AUTODOME IP 4000i Preparing the Camera | en 13

Bosch Security Systems Installation Manual 2017.08 | 1.0 | F.01U.xxx.xxx

6 Preparing the Camera

Note: For pendant models, use T15.

For in-ceiling models, use T10.

1. Loosen the three (3) Hex screws in the trim ring / bubble enclosure with the appropriate
Torx screwdriver.

2. Remove the trim ring / bubble enclosure.

2.

1.

3×

T15

14 en | Preparing the Camera AUTODOME IP 4000i

2017.08 | 1.0 | F.01U.xxx.xxx Installation Manual Bosch Security Systems

2.

1.

3×

T10

3. Remove the foam insert that protects the camera block.

4. Remove the tape holding the plastic lens protector; remove the lens protector.