Bosch NBN-498-11P, Dinion2X NBN-498 Installation And Operation Manual
Dinion2X IP Camera
NBN-498
en Installation and Operation Manual
Dinion2X IP Camera Table of Contents | en 3
Bosch Security Systems Installation and Operation Manual AR18-10-B006 | v1.1 | 2010.06
Table of Contents
1Safety 8
1.1 Safety precautions 8
1.2 Important safety instructions 9
1.3 Connection in applications 10
1.4 FCC & ICES compliance 11
1.5 UL certification 13
1.6 Bosch notices 14
1.7 Copyrights 15
2 Introduction 16
2.1 Features 16
3 System Information 18
3.1 Overview of functions 18
3.1.1 Progressive scan 18
3.1.2 Day/Night function 18
3.1.3 Wide dynamic range 18
3.1.4 Tri-streaming 19
3.1.5 ONVIF (Open Network Video Interface Forum) 19
3.1.6 Audio 19
3.1.7 Alarm I/O 19
3.1.8 Tamper detection and motion detectors 19
3.1.9 Video encoding 19
3.1.10 Multicast 19
3.1.11 Power-over-Ethernet 20
3.1.12 Encryption 20
3.1.13 Receiver 20
3.1.14 Recording 20
3.1.15 Snapshots 20
3.1.16 Backup 20
3.1.17 Configuration 20
3.2 Operation with external systems 22
4 en | Table of Contents Dinion2X IP Camera
AR18-10-B006 | v1.1 | 2010.06 Installation and Operation Manual Bosch Security Systems
4 Planning 24
4.1 Unpacking 24
4.2 System requirements 25
4.3 Install players 26
5 Installation 27
5.1 Network (and power) connector 27
5.2 Power connector 28
5.3 Alarm and relay connector 29
5.4 Audio connectors 30
5.5 Video service monitor connector 31
5.6 Data connector 32
5.7 Lens mounting 33
5.8 Mounting the camera 34
5.9 Using the camera install menu 35
5.10 Back focus adjustment 35
5.11 Lens adjustment 36
5.11.1 DC-iris lens 36
5.11.2 Manual-iris lens 36
5.11.3 Video-iris lens 37
5.12 Reset button 37
6 Camera set-up 38
6.1 Camera menu navigation 38
6.2 Install menu 39
6.2.1 Pre-defined modes 39
6.2.2 Lens Wizard submenu 40
6.2.3 Network submenu 41
6.2.4 Defaults submenu 41
6.3 Day/Night switching 42
7 Browser connection 43
7.1 System requirements 43
7.2 Establishing the connection 44
7.2.1 Password protection in camera 44
Dinion2X IP Camera Table of Contents | en 5
Bosch Security Systems Installation and Operation Manual AR18-10-B006 | v1.1 | 2010.06
7.3 Protected network 44
7.4 Connecting to a hardware decoder 45
7.4.1 Alarm connection 45
7.5 Connection established 46
7.5.1 LIVEPAGE 46
7.5.2 RECORDINGS 46
7.5.3 SETTINGS 46
8 Basic Mode 48
8.1 Basic Mode menu tree 48
8.2 Device Access 49
8.2.1 Camera name 49
8.2.2 Password 49
8.3 Date/Time 50
8.4 Network 51
8.5 Encoder Profile 52
8.6 Audio 52
8.7 Recording 52
8.7.1 Storage medium 52
8.8 System Overview 52
9 Advanced Mode 53
9.1 Advanced Mode menu tree 53
9.2 General 55
9.2.1 Identification 55
9.2.2 Password 55
9.2.3 Date/Time 56
9.2.4 Display Stamping 58
9.3 Web Interface 60
9.3.1 Appearance 60
9.3.2 LIVEPAGE Functions 61
9.3.3 Logging 62
9.4 Encoder 63
9.4.1 Privacy Masks 63
9.4.2 Encoder Profile 63
9.4.3 Encoder Streams 67
6 en | Table of Contents Dinion2X IP Camera
AR18-10-B006 | v1.1 | 2010.06 Installation and Operation Manual Bosch Security Systems
9.5 Audio 68
9.6 Camera 69
9.6.1 Mode 69
9.6.2 ALC 70
9.6.3 Shutter/AGC 71
9.6.4 Day/night 72
9.6.5 Enhance 73
9.6.6 Color 74
9.6.7 Installer Options 75
9.7 Recording 77
9.7.1 Storage Management 77
9.7.2 Recording Profiles 80
9.7.3 Retention Time 81
9.7.4 Recording Scheduler 82
9.7.5 Recording Status 83
9.8 Alarm 84
9.8.1 Alarm Connections 84
9.8.2 Video Content Analyses (VCA) 87
9.8.3 VCA configuration- Profiles 88
9.8.4 VCA configuration - Scheduled 94
9.8.5 VCA configuration - Event triggered 96
9.8.6 Audio Alarm 97
9.8.7 Alarm E-Mail 98
9.8.8 Alarm Task Editor 100
9.9 Interfaces 101
9.9.1 Alarm input 101
9.9.2 Relay 101
9.9.3 COM1 102
9.10 Network 103
9.10.1 Network 103
9.10.2 Advanced 107
9.10.3 Multicasting 108
9.10.4 JPEG Posting 109
9.10.5 Encryption 110
9.11 Service 111
9.11.1 Maintenance 111
9.11.2 Licenses 113
Dinion2X IP Camera Table of Contents | en 7
Bosch Security Systems Installation and Operation Manual AR18-10-B006 | v1.1 | 2010.06
9.11.3 System Overview 113
10 Operation via the browser 114
10.1 Livepage 114
10.1.1 Processor load 114
10.1.2 Image selection 115
10.1.3 View Control 115
10.1.4 Digital I/O 115
10.1.5 System Log / Event Log 115
10.1.6 Saving snapshots 115
10.1.7 Recording video sequences 116
10.1.8 Running recording program 116
10.1.9 Audio communication 116
10.2 Recordings page 117
10.2.1 Controlling playback 117
11 Troubleshooting 119
11.1 Function test 119
11.2 Resolving problems 120
11.3 Customer service 122
12 Maintenance 123
12.1 Testing the network connection 123
12.2 Communication with Terminal Program 123
12.3 Repairs 125
12.3.1 Transfer and disposal 125
13 Technical Data 126
13.1 Specifications 126
13.1.1 Dimensions 129
13.1.2 Accessories 130
Glossary 131
8 en | Safety Dinion2X IP Camera
AR18-10-B006 | v1.1 | 2010.06 Installation and Operation Manual Bosch Security Systems
1Safety
1.1 Safety precautions
DANGER!
High risk: This symbol indicates an imminently hazardous
situation such as "Dangerous Voltage" inside the product.
If not avoided, this will result in an electrical shock, serious
bodily injury, or death.
WARNING!
Medium risk: Indicates a potentially hazardous situation.
If not avoided, this could result in minor or moderate bodily
injury.
CAUTION!
Low risk: Indicates a potentially hazardous situation.
If not avoided, this could result in property damage or risk of
damage to the unit.
Dinion2X IP Camera Safety | en 9
Bosch Security Systems Installation and Operation Manual AR18-10-B006 | v1.1 | 2010.06
1.2 Important safety instructions
Read, follow, and retain for future reference all of the following
safety instructions. Follow all warnings on the unit and in the
operating instructions before operating the unit.
1. Clean only with a dry cloth. Do not use liquid cleaners or
aerosol cleaners.
2. Do not install unit near any heat sources such as radiators,
heaters, stoves, or other equipment (including amplifiers)
that produce heat.
3. Never spill liquid of any kind on the unit.
4. Take precautions to protect the unit from power and
lightning surges.
5. Adust only those controls specified in the operating
instructions.
6. Operate the unit only from the type of power source
indicated on the label.
7. Unless qualified, do not attempt to service a damaged unit
yourself. Refer all servicing to qualified service personnel.
8. Install in accordance with the manufacturer's instructions
in accordance with applicable local codes. Use only
attachments/accessories specified by the manufacturer.
Equipment change or modification could void the user's
guarantee or authorization agreement.
10 en | Safety Dinion2X IP Camera
AR18-10-B006 | v1.1 | 2010.06 Installation and Operation Manual Bosch Security Systems
1.3 Connection in applications
Power lines: An outdoor system should not be located in the
vicinity of overhead power lines, electrical lights, or power
circuits, or where it may contact such power lines or circuits.
When installing an outdoor system, extreme care should be
taken to keep from touching power lines or circuits, as this
contact may be fatal.
U.S.A. models only - refer to the National Electrical Code Article
820 regarding installation of CATV systems.
12 VDC / 24 VAC power source: This unit is intended to
operate with a limited power source. The unit is intended to
operate at either 12 VDC or 24 VAC (if PoE is not available).
User supplied wiring must be in compliance with electrical
codes (Class 2 power levels). If 24 VAC is used, do not ground
the 24 VAC supply at the terminals or at the unit's power supply
terminals.
PoE: Use only approved PoE devices. Power-over-Ethernet can
be connected at the same time as a 12 VDC or 24 VAC power
supply.
CAUTION!
The Low Voltage power supply unit must comply with EN/UL
60950. The power supply must be a SELV-LPS unit or a SELV Class 2 unit (Safety Extra Low Voltage - Limited Power Source).
Dinion2X IP Camera Safety | en 11
Bosch Security Systems Installation and Operation Manual AR18-10-B006 | v1.1 | 2010.06
1.4 FCC & ICES compliance
FCC & ICES Information
(U.S.A. and Canadian Models Only)
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there is no
guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following
measures:
– reorient or relocate the receiving antenna;
– increase the separation between the equipment and
receiver;
– connect the equipment into an outlet on a circuit different
from that to which the receiver is connected;
– consult the dealer or an experienced radio/TV technician
for help.
Intentional or unintentional modifications, not expressly
approved by the party responsible for compliance, shall not be
made. Any such modifications could void the user's authority to
operate the equipment. If necessary, the user should consult
the dealer or an experienced radio/television technician for
corrective action.
The user may find the following booklet, prepared by the
Federal Communications Commission, helpful: How to Identify
and Resolve Radio-TV Interference Problems. This booklet is
available from the U.S. Government Printing Office,
Washington, DC 20402, Stock No. 004-000-00345-4.
12 en | Safety Dinion2X IP Camera
AR18-10-B006 | v1.1 | 2010.06 Installation and Operation Manual Bosch Security Systems
Informations FCC et ICES
(modèles utilisés aux États-Unis et au Canada uniquement)
Suite à différents tests, cet appareil s'est révélé conforme aux
exigences imposées aux appareils numériques de classe B, en
vertu de la section 15 du règlement de la Commission fédérale
des communications des États-Unis (FCC), et en vertu de la
norme ICES-003 d'Industrie Canada. Ces exigences visent à
fournir une protection raisonnable contre les interférences
nuisibles lorsque l'appareil est utilisé dans le cadre d'une
installation résidentielle. Cet appareil génère, utilise et émet
de l'énergie de radiofréquences et peut, en cas d'installation ou
d'utilisation non conforme aux instructions, engendrer des
interférences nuisibles au niveau des radiocommunications.
Toutefois, rien ne garantit l'absence d'interférences dans une
installation particulière. Il est possible de déterminer la
production d'interférences en mettant l'appareil
successivement hors et sous tension, tout en contrôlant la
réception radio ou télévision. L'utilisateur peut parvenir à
éliminer les interférences éventuelles en prenant une ou
plusieurs des mesures suivantes:
– Modifier l'orientation ou l'emplacement de l'antenne
réceptrice;
– Éloigner l'appareil du récepteur;
– Brancher l'appareil sur une prise située sur un circuit
différent de celui du récepteur;
– Consulter le revendeur ou un technicien qualifié en radio/
télévision pour obtenir de l'aide.
Toute modification apportée au produit, non expressément
approuvée par la partie responsable de l'appareil, est
strictement interdite. Une telle modification est susceptible
d'entraîner la révocation du droit d'utilisation de l'appareil.
La brochure suivante, publiée par la Commission fédérale des
communications (FCC), peut s'avérer utile : Comment identifier
et résoudre les problèmes d’interférences de radio et de télévision.
Cette brochure est disponible auprès du U.S. Government
Printing Office, Washington, DC 20402, États-Unis, sous la
référence n° 004-000-00345-4.
Dinion2X IP Camera Safety | en 13
Bosch Security Systems Installation and Operation Manual AR18-10-B006 | v1.1 | 2010.06
1.5 UL certification
Disclaimer
Underwriter Laboratories Inc. ("UL") has not tested the
performance or reliability of the security or signaling aspects of
this product. UL has only tested fire, shock and/or casualty
hazards as outlined in UL's Standard(s) for Safety for Information
Technology Equipment, UL 60950-1. UL Certification does not
cover the performance or reliability of the security or signaling
aspects of this product.
UL MAKES NO REPRESENTATIONS, WARRANTIES, OR
CERTIFICATIONS WHATSOEVER REGARDING THE
PERFORMANCE OR RELIABILITY OF ANY SECURITY OR
SIGNALING RELATED FUNCTIONS OF THIS PRODUCT.
Disposal - Your Bosch product was developed and
manufactured with high-quality material and components that
can be recycled and reused. This symbol means that
electronic and electrical appliances, which have reached the
end of their working life, must be collected and disposed of
separately from household waste material. Separate collecting
systems are usually in place for disused electronic and
electrical products. Please dispose of these units at an
environmentally compatible recycling facility, per European
Directive 2002/96/EC
14 en | Safety Dinion2X IP Camera
AR18-10-B006 | v1.1 | 2010.06 Installation and Operation Manual Bosch Security Systems
1.6 Bosch notices
Video loss
Video loss is inherent to digital video recording; therefore,
Bosch Security Systems cannot be held liable for any damage
that results from missing video information. To minimize the
risk of lost digital information, Bosch Security Systems
recommends multiple, redundant recording systems, and a
procedure to back up all analog and digital information.
Copyright
This manual is the intellectual property of Bosch Security
Systems and is protected by copyright.
All rights reserved.
Trademarks
All hardware and software product names used in this
document are likely to be registered trademarks and must be
treated accordingly.
Note
This manual has been compiled with great care and the
information it contains has been thoroughly verified. The text
was complete and correct at the time of printing. The ongoing
development of the products may mean that the content of the
user guide can change without notice. Bosch Security Systems
accepts no liability for damage resulting directly or indirectly
from faults, incompleteness or discrepancies between the user
guide and the product described.
More information
For more information please contact the nearest Bosch Security
Systems location or visit www.boschsecurity.com
Dinion2X IP Camera Safety | en 15
Bosch Security Systems Installation and Operation Manual AR18-10-B006 | v1.1 | 2010.06
1.7 Copyrights
The firmware 4.1 uses the fonts "Adobe-Helvetica-Bold-RNormal--24-240-75-75-P-138-ISO10646-1" and "AdobeHelvetica-Bold-R-Normal--12-120-75-75-P-70-ISO10646-1" under
the following copyright:
Copyright 1984-1989, 1994 Adobe Systems Incorporated.
Copyright 1988, 1994 Digital Equipment Corporation.
Permission to use, copy, modify, distribute and sell this
software and its documentation for any purpose and without
fee is hereby granted, provided that the above copyright
notices appear in all copies and that both those copyright
notices and this permission notice appear in supporting
documentation, and that the names of Adobe Systems and
Digital Equipment Corporation not be used in advertising or
publicity pertaining to distribution of the software without
specific, written prior permission.
This software is based in part on the work of the Independent
JPEG Group.
16 en | Introduction Dinion2X IP Camera
AR18-10-B006 | v1.1 | 2010.06 Installation and Operation Manual Bosch Security Systems
2 Introduction
2.1 Features
The Dinion2x IP Day/Night camera is a high-performance, smart
surveillance color camera. It incorporates 20-bit digital signal
processing and a wide dynamic range sensor for outstanding
picture performance under all lighting conditons.
The camera uses H.264 compression technology to give clear
images while reducing bandwidth and storage requirements. It
is also ONVIF compliant to improve compatibility during system
integration.
The camera operates as a network video server and transmits
video and control signals over data networks, such as Ethernet
LANs and the Internet.
The camera is easy to install and ready to use.
Features include:
– Progressive scan
– True Day/Night performance with switchable IR filter
– 1/3-inch CCD sensor with wide dynamic range
– Tri-streaming (two H.264 streams and one M-JPEG stream)
– Complies with the ONVIF standard for wide compatibility
– Two-way audio and audio alarm
– Alarm input and alarm output to external devices
– Dynamic engine with Smart BLC
– Six pre-programmed operation modes
– Adaptive dynamic noise reduction
– Enhanced video motion detection
– Video and data transmission over IP data networks
– Multicast function for simultaneous picture transmission to
multiple receivers
– Integrated Ethernet interface (10/100 Base-T)
– Power-over-Ethernet (PoE)
– Remote control of all built-in functions via TCP/IP
– Data interface RS485/RS422/RS232 for control of pan or
tilt heads or motorized zoom lenses (PTZ control)
Dinion2X IP Camera Introduction | en 17
Bosch Security Systems Installation and Operation Manual AR18-10-B006 | v1.1 | 2010.06
– Password protection to prevent unauthorized connection
or configuration changes
– Event-driven, automatic connection (for example, at
switch-on and for alarms)
– Fast, convenient configuration using the integrated Web
server and a browser
– Firmware update through flash memory
– Convenient upload and download of configuration data
18 en | System Information Dinion2X IP Camera
AR18-10-B006 | v1.1 | 2010.06 Installation and Operation Manual Bosch Security Systems
3 System Information
3.1 Overview of functions
The camera incorporates a network video server. Its primary
function is to encode video and control data for transmission
over an IP network. With its H.264 encoding, it is ideally suited
for IP communication and for remote access to digital video
recorders and IP systems. The use of existing networks means
that integration with CCTV systems or local networks can be
achieved quickly and easily. Video images from a single camera
can be simultaneously received on several receivers.
3.1.1 Progressive scan
The camera captures and processes progressively scanned
images. When there is fast motion in a scene, progressively
scanned images are generally sharper than interlaced images.
3.1.2 Day/Night function
The Day/Night function provides enhanced night viewing by
increasing the IR sensitivity. The motorized IR filter can be
removed in low-light or IR illuminated applications. The IR filter
switches from color to monochrome automatically by sensing
the illumination level. In auto switching mode the camera
prioritizes motion (the camera gives sharp images without
motion blur) or color (the camera gives color pictures as long as
the light level permits).
3.1.3 Wide dynamic range
A unique combination of 20-bit digital video processing that
enhances sensitivity and 2X-Dynamic which extends the
dynamic range, provides a sharper, more detailed image with
outstanding accuracy in color reproduction. The 20-bit digital
signal is automatically processed to optimally capture the detail
in both the high and low light areas of the scene
simultaneously, maximizing the information visible in the
picture.
Dinion2X IP Camera System Information | en 19
Bosch Security Systems Installation and Operation Manual AR18-10-B006 | v1.1 | 2010.06
3.1.4 Tri-streaming
Tri-streaming allows the data stream to be encoded
simultaneously according to three different, individually
customized profiles. This creates two full H.264 streams that
can serve different purposes and an additional M-JPEG stream.
3.1.5 ONVIF (Open Network Video Interface Forum)
The camera complies to the ONVIF standard which means that
it is easier to install and integrate into larger systems. The
ONVIF standard is a global standard for the interface of network
video products.
3.1.6 Audio
Two-way duplex audio is available in the unit for live voice
communications or audio recording.
3.1.7 Alarm I/O
The alarm input can be used to control the functionality of the
unit. An alarm output can control external devices.
3.1.8 Tamper detection and motion detectors
The camera offers a wide range of configuration options for
alarm signaling in the event of tampering with the camera. An
algorithm for detecting movement in the video image is also
part of the scope of delivery and can optionally be extended to
include special video analysis algorithms.
3.1.9 Video encoding
The camera uses the H.264 compression standards. Thanks to
efficient encoding, the data rate remains low even with high
image quality and can also be adapted to local conditions
within wide limits.
3.1.10 Multicast
In suitably configured networks, the multicast function enables
simultaneous, real time transmission to multiple receivers. The
prerequisite for this is that the UDP and IGMP V2 protocols are
implemented on the network.
20 en | System Information Dinion2X IP Camera
AR18-10-B006 | v1.1 | 2010.06 Installation and Operation Manual Bosch Security Systems
3.1.11 Power-over-Ethernet
Power for the camera can be supplied via a Power-overEthernet compliant network cable connection. With this
configuration, only a single cable connection is required to
view, power, and control the camera.
3.1.12 Encryption
The unit offers a variety of options for protection against
unauthorized reading. Web browser connections can be
protected using HTTPS. Protect the control channels via the
SSL encryption protocol. With an additional license, the user
data itself can be encrypted.
3.1.13 Receiver
H.264 compatible hardware decoders can be used as a
receiver. Computers with decoding software such as VIDOS, or
computers with the Microsoft Internet Explorer web browser
installed, can also be used as receivers.
3.1.14 Recording
The camera can be used with an iSCSI server connected via the
network to store long-term recordings.
3.1.15 Snapshots
Individual video frames (snapshots) can be called up as JPEG
images, stored on the hard drive, or displayed in a separate
browser window.
3.1.16 Backup
The browser application has an icon for saving the video images
provided by the unit as a file on your computer's hard drive.
Clicking this icon stores the video sequences and they can be
replayed with the Player from Bosch Security Systems included
with the package.
3.1.17 Configuration
The camera can be configured using a browser on the local
network (Intranet) or from the Internet. Similarly, firmware
updates and rapid loading of device configurations are also
Dinion2X IP Camera System Information | en 21
Bosch Security Systems Installation and Operation Manual AR18-10-B006 | v1.1 | 2010.06
possible. Configuration settings can be stored as files on a
computer and copied from one camera to another.
22 en | System Information Dinion2X IP Camera
AR18-10-B006 | v1.1 | 2010.06 Installation and Operation Manual Bosch Security Systems
3.2 Operation with external systems
The camera can be used with a variety of Bosch software and
hardware systems:
– Bosch Video Management System
–VIDOS video management software
– DiBos 900 Series digital video recorder
– Divar 700 Series digital video recorder
Note:
When connected to any of these systems, many of the camera
configuration parameters are controlled by the system and not
by the settings made via a web browser connected to the
camera.
Bosch Video Management System
The Bosch Video Management System is a unique enterprise IP
video surveillance solution that provides seamless management
of digital video, audio, and data across any IP network. It is
designed to work with Bosch CCTV products as part of a total
video surveillance management system. Integrate your existing
components into one easy-to-manage system, or use Bosch’s
full-line capabilities and benefit from a complete surveillance
solution based on cutting-edge technology and years of
experience.
VIDOS
The camera video server and VIDOS software combine to
provide a high-performance system solution. VIDOS is software
for operating, controlling, and administering CCTV installations
(such as surveillance systems) at remote locations. It runs
under Microsoft Windows operating systems. Its main job is
decoding video, audio, and control data from a remote
transmitter. There are many options available for operation and
configuration when using a camera with VIDOS.
DiBos 900 Series
The camera is also designed for use with DiBos 900 Series
Video Recorders. DiBos can record up to 32 video and audio
Dinion2X IP Camera System Information | en 23
Bosch Security Systems Installation and Operation Manual AR18-10-B006 | v1.1 | 2010.06
streams, and is available as software or as a hybrid DVR with
additional analog camera and audio inputs. DiBos supports
various functions of the camera, such as controlling relays,
remote control of peripheral devices, and remote configuration.
DiBos can use alarm inputs to trigger actions and, when motion
detection Motion+ is active, can record the relevant cells,
making intelligent motion detection possible.
Divar 700 Series
The Divar 700 Series of digital video recorders can view and
record images from the camera via a network connection. The
Divar 700 Series controls the camera so that the correct
settings are used.
24 en | Planning Dinion2X IP Camera
AR18-10-B006 | v1.1 | 2010.06 Installation and Operation Manual Bosch Security Systems
4 Planning
4.1 Unpacking
Unpack carefully and handle the equipment with care. The
packaging contains:
– Dinion2X IP camera
– CCD protection cap (mounted on camera)
– Power connector
– Alarm I/O connector
– Data connector
– Spare lens connector (male)
– DVD ROM (mini)
–Manual
– System requirements
– Configuration Manager
– BVIP Lite Suite
–MPEG ActiveX control
– DirectX control
– Microsoft Internet Explorer
–Sun JVM
– Player and Archive Player
– Adobe Acrobat Reader
– Quick install instructions
– Safety instructions
If equipment has been damaged during shipment, repack it in
the original packaging and notify the shipping agent or supplier.
Dinion2X IP Camera Planning | en 25
Bosch Security Systems Installation and Operation Manual AR18-10-B006 | v1.1 | 2010.06
4.2 System requirements
– Computer with Windows XP/Vista operating system,
network access, and Microsoft Internet Explorer web
browser version 7.0 or later
or
– Computer with Windows XP/Vista operating system,
network access and reception software, for example
VIDOS, Bosch VMS, or DIBOS 900 Series
or
– H.264 compatible hardware decoder from
Bosch Security Systems (such as VIP XD) as a receiver and
a connected video monitor
or
– Divar 700 Series Digital Video Recorder
The minimum PC requirements are:
– Operating platform: A PC running Windows XP or
Windows Vista with IE 7.0
– Processor: Dual core, 3.0 GHz
– RAM memory: 256 MB
– Monitor resolution: 1024 x 768
– Network interface: 100-BaseT
–DirectX: 9.0c
Make sure the graphics card is set to 16-bit or 32-bit color
depth and that Sun JVM is installed on your PC. To play back
live video images, an appropriate ActiveX must be installed on
the computer. If necessary, install the required software and
controls from the product DVD provided. For further assistance,
contact your PC system administrator.
26 en | Planning Dinion2X IP Camera
AR18-10-B006 | v1.1 | 2010.06 Installation and Operation Manual Bosch Security Systems
4.3 Install players
Play back saved-video sequences using the Player from
Bosch Security Systems. This can be found on the DVD-ROM
supplied.
to play back saved sequences using the Player, suitable ActiveX
software must be installed on the computer.
1. Insert the DVD into the DVD-ROM drive of the computer. If
the DVD does not start automatically, open the DVD in
Windows Explorer and double-click the index.html file to
start the installation.
2. Select a language from the list box at the top.
3. Click Tools in the menu.
4. Click Archive Player; the installation starts.
5. Follow the instructions in the installation program. The
Archive Player is installed together with the Player.
6. After a successful installation, two new icons for the Player
and the Archive Player appear on the desktop.
7. Double-click the Player icon to start the Player.
Dinion2X IP Camera Installation | en 27
Bosch Security Systems Installation and Operation Manual AR18-10-B006 | v1.1 | 2010.06
5 Installation
5.1 Network (and power) connector
Figure 5.1 Network connection
– Connect the camera to a 10/100 Base-T network.
– Use screened UTP Category 5e cable with RJ45 connectors
(the camera network socket is Auto MDIX compliant).
– Power can be supplied to the camera via the Ethernet
cable compliant with the Power-over-Ethernet
(IEEE 802.3af) standard.
The multicolored LED beside the Ethernet connection indicates
Power (red), IP connection (green) and IP traffic (green
flashing). It can be disabled in the Settings/Camera Settings/
Install options menu.
By default, power is supplied to the camera via the Ethernet
cable, compliant with the Power-over-Ethernet standard.
CAUTION!
Installation should only be performed by qualified service
personnel in accordance with the National Electrical Code or
applicable local codes.
UTP Cat 5 RJ45
1
2
3
4
5
6
E
T
H
P
o
E
ALARM
AUDIO IN
AUDIO OUT
VIDEO
DATA
1
2
3
4
5
6
–
+
12 VDC
24 VAC
28 en | Installation Dinion2X IP Camera
AR18-10-B006 | v1.1 | 2010.06 Installation and Operation Manual Bosch Security Systems
5.2 Power connector
Figure 5.2 Power connection
Connect power from a 24 VAC or 12 VDC class 2 power supply
as follows:
– Use AWG16 to 22 stranded wire or AWG16 to 26 solid
wire; cut back 5 mm (0.2 in) of insulation.
– Loosen the screws of the supplied 2-pole connector and
insert the wires.
– Tighten the screws and insert the 2-pole connector into
the power socket of the camera.
Note:
For a DC supply the polarity is important. Incorrect polarity
does not damage the camera but it will not switch on.
1
2
3
4
5
6
E
T
H
P
o
E
ALARM
AUDIO IN
AUDIO OUT
VIDEO
DATA
1
2
3
4
5
6
–
+
12 VDC
24 VAC
5 mm
0.2 in
Dinion2X IP Camera Installation | en 29
Bosch Security Systems Installation and Operation Manual AR18-10-B006 | v1.1 | 2010.06
5.3 Alarm and relay connector
Figure 5.3 Alarm and relay connector pins
– Max. wire diameter AWG 22-28 for both stranded and
solid; cut back 5 mm (0.2 in) of insulation.
– Alarm output relay switching capability: Max voltage 30VAC
or +40 VDC. Max 0.5 A continuous, 10 VA.
– Alarm in: TTL logic, +5V nominal, +40 VDC max, DC coupled
with 22 kOhm pull-up to +3.3 V.
– Alarm in: configurable as active low or active high.
– Max. 42 V allowed between camera ground and each of the
relay pins.
Use the alarm input to connect external alarm devices such as
door contacts or sensors. A zero potential make-contact or
switch can be used as the actuator (use a bounce-free contact
system).
Use the alarm relay output for switching external devices such
as lamps or sirens.
Pin Alarm socket
1 Alarm in 1
2 Alarm in 2
3 Relay out contact 1
4Ground
5Ground
6 Relay out contact 2
Alarm
1
2
3
4
5
6
5 mm
(0.2 in)
30 en | Installation Dinion2X IP Camera
AR18-10-B006 | v1.1 | 2010.06 Installation and Operation Manual Bosch Security Systems
5.4 Audio connectors
Figure 5.4 Audio connectors
Connect audio devices to the Audio In and Audio Out
connectors.
The unit has full-duplex mono audio. The two-way
communication can be used to connect a speaker or door
intercom system. The audio input signal is transmitted in sync.
with the video signal.
Audio input: Line input level (not suitable for direct
microphone signal); impedance 9 kOhm typical; 5.5 Vpp
maximum input voltage.
Audio output: Line output level (not suitable for direct speaker
connection); impedance 16 Ohm minimum; 3 Vpp maximum
output voltage.
Wiring: Shielded audio connection cable is advised. Observe
maximum cable lengths for audio line input and output levels.
1
2
3
4
5
6
E
T
H
P
o
E
ALARM
AUDIO IN
AUDIO OUT
VIDEO
DATA
1
2
3
4
5
6
–
+
12 VDC
24 VAC
GND
Line
Loading...