Bosch LE10 User Manual

LE10 Radio Receiver

CRS-URE-0100 | F.01U.278.517 | V2.0 | 2012.11

en User Manual

LE10 Radio Receiver Table of Contents | en 3

Table of Contents

1 Safety instructions 5

1.1 General safety instructions 5

1.2 Environmental conditions 5

1.3 Electrostatic Discharge (ESD) 5

2 Product information 6

2.1 General description 6

2.2 Compatible transmitters 6

2.3 Main applications 7

2.4 Description of the different modes 7

3 Installation 9

3.1 Unpacking 9

3.2 Connecting the power supply 9

3.2.1 Power supply with the RJ12 power socket 9

3.2.2 Power supply connected to a wired installation 9

3.3 Wall installation 10

4 Connection compartment 11

4.1 Connecting ports 11

4.2 Mode selection 12

4.2.1 Mode indication after power on 12

5 Programming 13

5.1 Enter programming mode 13

5.2 Program a transmitter in modes 1, 2 or 5 13

5.3 Delete a transmitter 14

5.4 Delete all transmitters 14

5.5 Program a door address in modes 3 or 4 15

5.5.1 Programming in modes 6 or 7 15

6Operation 16

6.1 Standby mode 16

6.1.1 Standby with no transmitter programmed 16

6.1.2 Standby with at least one transmitter programmed 16

Bosch Security Systems User Manual F.01U.278.517 | V2.0 | 2012.11

4 en | Table of Contents LE10 Radio Receiver

6.2 Normal mode (modes 1 and 2) 16

6.2.1 Activation of a transmitter in normal mode 16

6.3 Dementia (mode 3) 17

6.3.1 Activation of a MIYS37L Wristband Transmitter 17

6.3.2 Detection of a MIYS37E Wristband Transmitter alone 18

6.3.3 Detection of a MIYS37L Wristband Transmitter with a MIYS37E
Wristband Transmitter nearby 18

6.4 Dementia with Accompany (mode 4) 19

6.4.1 Activation of a MIYS37L Wristband Transmitter 19

6.5 Remote control (mode 5) 19

6.5.1 Activation of a programmed transmitter 19

6.5.2 Activation of a programmed transmitter with a battery-low
message or with a new battery 20

6.6 Open receiver (modes 6 and 7) 20

6.6.1 Activation of a transmitter in the reception range 20

6.7 Daily messages in modes 1, 2 or 5 20

6.7.1 Daily message with battery-low signal 20

6.7.2 Reset of a battery-low indication with button T1 21

6.8 Extended MIYN46 (mode 8, only with SW 1.10) 21

6.9 Dual channel receiver (mode 9, only with SW 1.10) 22

7 Technical data 23

F.01U.278.517 | V2.0 | 2012.11 User Manual Bosch Security Systems

LE10 Radio Receiver Safety instructions | en 5

1 Safety instructions

1.1 General safety instructions

Installation and initial operation should only be carried out by
trained service personnel.

1.2 Environmental conditions

The LE10 Radio Receiver must not be located near a water tap
or any other source of water. The electrical safety of the LE10
Radio Receiver is only guaranteed if the electrical installation is
in accordance with the national regulations and if this
installation works properly. The LE10 Radio Receiver may not
be used in buildings prone to fire and explosion hazards.
The LE10 Radio Receiver may not be used under exposure to
direct sunlight, to heat, to dust or to an excessive humidity
(only use the equipment in a clean environment).

1.3 Electrostatic Discharge (ESD)

WARNING!

The LE10 Radio Receiver contains highly sensitive electronic
components. It should be opened only in an ESD protected
environment with respect to the following precautions.
Discharge yourself from electrostatic loads by touching a
grounded conductive surface before opening the unit. Avoid
touching conductive parts inside the LE10 Radio Receiver if not
absolutely necessary.

Bosch Security Systems User Manual F.01U.278.517 | V2.0 | 2012.11

6 en | Product information LE10 Radio Receiver

LED 1 (green)

LED 2 (red)

2 Product information

2.1 General description

The LE10 Radio Receiver is designed to receive radio signals
from different Bosch radio transmitters at the frequency of

434.01 MHz. After receiving radio signals from either
programmed or not programmed wireless transmitters, the
LE10 Radio Receiver reacts by activating its two green and red
LEDs and by switching relay outputs of two relays.

Figure 2.1 Front view of the LE10 Radio Receiver

2.2 Compatible transmitters

All of the following Bosch wireless transmitters are compatible
with the LE10 Radio Receiver:
– MIYS37 Wristband Transmitters
– MIYS37L Wristband Transmitters with Locating function

F.01U.278.517 | V2.0 | 2012.11 User Manual Bosch Security Systems

– MIYS37E Wristband Transmitters with Accompany function
– MIYS35 Pendant Transmitters
– MIYMD ManDown Sensors
– MIYRAC Wireless Contact

LE10 Radio Receiver Product information | en 7

2.3 Main applications

LE10 Radio Receiver as small stand alone call system

After receiving a radio signal from a programmed radio
transmitter, the relay output switches a siren or a lamp to
indicate locally a wireless call.

LE10 Radio Receiver connected to a emergency call system via relay contact

After receiving a radio signal from a programmed radio
transmitter, the relay will be switched. This relay output is
connected to a wired emergency call system by wire and hereby
a call will be generated or forwarded.

LE10 Radio Receiver as part of a Resident Alert System monitoring dementia

After receiving a signal from a dementia transmitter, the relay
will be activated to close a monitored door.

2.4 Description of the different modes

Mode Name Description

1 Normal 20 wireless transmitters can be programmed.

Calls are indicated by the red LED and Relay 1.
A battery-low signal is indicated by the red
LED and Relay 2.

2 Normal, with red LED

deactivated at
battery-low indication

3 Dementia The MIYS37L and MIYS37E wireless

The same functions as in mode 1 are available,
except for the battery-low signal which is not
indicated by the red LED, but only by Relay 2.

transmitters are detected. Relay 1 can be used
to lock a monitored door. Relay 2 can be used
to interrupt a monitoring loop.

Bosch Security Systems User Manual F.01U.278.517 | V2.0 | 2012.11

8 en | Product information LE10 Radio Receiver

Mode Name Description

4 Dementia with

Accompany

This mode allows to connect the LE10 Radio
Receiver to a wired emergency call system, in
which the Accompany function can be
implemented. It will wait 10 seconds after
receiving a signal from a MIYS37L transmitter.
If it detects a MIYS37E transmitter in this lapse
of time, no alarm is generated. If not, Relay 1 is
activated for 2 seconds.

5 Remote control 20 wireless transmitters can be programmed.

Per sequence, only the same transmitter can
switch on and off the Relay1. A battery-low
signal is indicated by the red LED and Relay 2.

6 Open receiver No wireless transmitter needs to be

programmed. Any transmitter within reception
range of the LE10 Radio Receiver can activate
the device.

7 Open receiver with

reduced range

Same functions as in mode 6, but with
reduced range. This functionality is designed
to improve reception of transmitters located
closer to the LE10 Radio Receiver.

8 Extended MIYN46

transmitter
programming
(only with SW 1.10)

9 Dual channel receiver

(only with SW 1.10)

Additional MIYN46 transmitters can be
programmed. Behavior is similar to normal
mode 1, with certain differences according to
the transmitter that is activated.

Only MIYS37 wireless transmitters can be
programmed. Calls are indicated by Relay 1 or
Relay 2, according to the slot in which the
MIYS37 wireless transmitter is programmed. A
battery-low signal is indicated by the red LED.

NOTICE!

Factory setting is normal mode 1, in which 20 wireless
transmitters can be programmed. Calls are indicated by the red
LED and Relay 1. A battery-low signal is indicated by the red
LED and Relay 2.

F.01U.278.517 | V2.0 | 2012.11 User Manual Bosch Security Systems

LE10 Radio Receiver Installation | en 9

3 Installation

3.1 Unpacking

The LE10 Radio Receiver is carefully packed for transportation.
The components contained in the box are protected, but should
be handled with care. Store the packaging material for further
use (storage or transport). In case of defective or missing
equipment, do not try to install the LE10 Radio Receiver.
Contact immediately your local representative.

1. Take all components out of the box and place the LE10 Radio
Receiver on the working space.

2. Check that the following accessories are delivered: the
fixings (2 screws and 2 screw anchors) and this user manual.

3. Check that the LE10 Radio Receiver and its accessories have
not been damaged during transportation.

3.2 Connecting the power supply

There are two different ways to connect the power supply of
the LE10 Radio Receiver. After connection, the LE10 Radio
Receiver will be in standby mode.

3.2.1 Power supply with the RJ12 power socket

The LE10 Radio Receiver can be powered by a power supply
unit (PSU). The PSU should be plugged in the RJ12 socket on
the rear side of the unit and should be easily accessible at any
time. See Section 4.1 Connecting ports, page 11 for access to
the socket. See Section 7 Technical data, page 23 for
information about the power supply.

3.2.2 Power supply connected to a wired installation

The LE10 Radio Receiver can be powered by connecting a wired
input into poles 1 and 2 of the connection board. See
Section 4.1 Connecting ports, page 11 for information about the
power supply.

Bosch Security Systems User Manual F.01U.278.517 | V2.0 | 2012.11

10 en | Installation LE10 Radio Receiver

3.4 in (80 mm)

Ø0.3in

(7.5 mm)

2.2 in (53.8 mm)

0.51 in
(13.1 mm)

0.15 in

(3.7 mm)

0.63 in (16 mm)

0.26 in (6.6 mm)

2.36 in (59.9 mm)

1.06 in (27 mm

0.71 in (18.1 mm)

5.16 in (131 mm)

0.08 in

(2 mm)

1.62 in

(26 mm)

0.15 in

(3.7 mm)

3.3 Wall installation

You can fasten the LE10 Radio Receiver on a smooth wall
surface using two screws. Installation cables should be placed
inside the cable channels on the bottom.

Figure 3.1 Dimensions of the backside of the LE10 Radio Receiver

F.01U.278.517 | V2.0 | 2012.11 User Manual Bosch Security Systems

LE10 Radio Receiver Connection compartment | en 11

T1

–

+

8-30VDC

Relay 2
output

Relay 1
output

S3

12345

P133
RJ12

P130

6543 21

–

+

Relay 1 output

61

ON

OFF

4 Connection compartment

4.1 Connecting ports

To open the device:
– hold the LE10 Radio Receiver in one hand, facing you, so

that you can see the Bosch logo and the two LEDs.

– grab the connection compartment housing with the other

hand and slide it towards you.

– you can now see the components as in the following

illustration:

Figure 4.1 LE10 Radio Receiver connection compartment

NOTICE!

The standby conditions of Relay 1 and Relay 2 are as shown in
this illustration.

Bosch Security Systems User Manual F.01U.278.517 | V2.0 | 2012.11

12 en | Connection compartment LE10 Radio Receiver

4.2 Mode selection

Modes 1 to 9 can be selected by operating switches 1 to 5 of
the 5-digits micro switch S3.

CAUTION!

After selecting the mode, disconnect the power supply and
connect it again.

Mode Description Switch number

12345

1 Normal mode off off off off off

2 Normal mode, with the red LED

deactivated at battery-low indication

3 Dementia mode off on off off off

4 Dementia with Accompany mode on on off off off

5 Remote control off off on off off

6 Open receiver on off on off off

7 Open receiver with reduced range off on on off off

8 Extended N46 (only with SW 1.10) on on on off off

9 Dual channel receiver (only with SW 1.10) off off off on off

on off off off off

NOTICE!
Factory setting is all switches set to off.

4.2.1 Mode indication after power on

– When the power supply is connected to the LE10 Radio

Receiver, the green LED will light up permanently for 2
seconds. Afterwards, the device will display the current
mode through the green LED, by blinking as many times as
the number of the mode. The green LED will then light up
permanently.
Example: In mode 8, the green LED will blink 8 times.

– When changing the mode, all programmed transmitters will

be deleted.

F.01U.278.517 | V2.0 | 2012.11 User Manual Bosch Security Systems

LE10 Radio Receiver Programming | en 13

5 Programming

5.1 Enter programming mode

To enter programming mode, press simply button T1 for the
desired time. See Section 4.1 Connecting ports, page 11.

NOTICE!

Both relays will not be activated in the programming mode.

5.2 Program a transmitter in modes 1, 2 or 5

NOTICE!

Per programming sequence only one transmitter can be
matched. You can program up to 20 transmitters.

To start programming

– Press button T1 for min. 1 second and max. 3 seconds.

Device behavior

– The green LED stays permanently on.
– The red LED blinks slowly for maximum 30 seconds.
Within these 30 seconds, activate the transmitter that you want
to match, the following behavior should be observed:
– The green LED and the red LED blink alternating for 6

seconds.
This indication confirms that the transmitter is programmed.
– If the transmitter is already programmed, then the red LED

blinks fast for 6 seconds after activating the transmitter.
– If 20 transmitters are already programmed, then the red

LED blinks fast for 10 seconds directly after activating the

button T1 between 1 and 3 seconds.

You can repeat the sequence with another transmitter.

Bosch Security Systems User Manual F.01U.278.517 | V2.0 | 2012.11

14 en | Programming LE10 Radio Receiver

5.3 Delete a transmitter

NOTICE!

Per sequence only one transmitter can be deleted.

To start deleting:

– Press button T1 for min. 5 seconds and max. 10 seconds.

Device behavior

– The green LED stays permanently on, then after 5 seconds

blinks fast 5 times.
– The red LED stays off and then blinks for 30 seconds.
Within these 30 seconds, activate the transmitter that you want
to delete, the following behavior should be observed:
– The green LED stays permanently on.
– The red LED stays permanently on for 5 seconds and then

turns off.
This indication confirms that the transmitter is deleted. You can
repeat the sequence with another transmitter.

5.4 Delete all transmitters

To start deleting

– Press button T1 for minimum 20 seconds and maximum 40

seconds.

Device behavior

– The green LED stays permanently on, then after 5 seconds,

blinks fast 5 times. After 20 seconds, the green LED will

blink for 20 seconds.
– At that moment, the red LED lights up permanently for 5

seconds then turns off.
This indication confirms that all transmitters are then deleted.

NOTICE!

If button T1 is pressed longer than 40 seconds, then the LE10
Radio Receiver will jump out of the programming mode.

F.01U.278.517 | V2.0 | 2012.11 User Manual Bosch Security Systems

LE10 Radio Receiver Programming | en 15

5.5 Program a door address in modes 3 or 4

You can program a door address stored in a MIYS37L Wristband
Transmitter with Locating function, in modes 3 or 4.

NOTICE!

A door address must be stored beforehand in a MIYS37L
Wristband Transmitter with Locating function.

NOTICE!

Only one door address of a MIYS37L Wristband Transmitter
with Locating function can be matched in the LE10 Radio
Receiver.

To start programming

– Press button T1 min. 1 second and max. 3 seconds.

Device behavior

– The green LED stays permanently on.
– The red LED blinks slow for max. 30 seconds.
– Activate the S37L Wristband Transmitter, which you desire

to match, before the end of the 30 seconds.

– Upon activating the transmitter, the green LED and the red

LED blink alternating quick for 6 seconds.
This indication confirms that the door address in the MIYS37L
Wristband Transmitter is matched in the LE10 Radio Receiver.

CAUTION!

When a new door address stored in a MIYS37L Wristband
Transmitter is programmed, it overwrites the current door
address.

5.5.1 Programming in modes 6 or 7

It is neither possible nor necessary to program a transmitter in
modes 6 or 7 (Open Receiver).

Bosch Security Systems User Manual F.01U.278.517 | V2.0 | 2012.11

16 en | Operation LE10 Radio Receiver

6 Operation

6.1 Standby mode

The LE10 Radio Receiver enters standby mode when the power
supply is connected. Both relays are off. See Section 4.2.1 Mode
indication after power on, page 12.

6.1.1 Standby with no transmitter programmed

Device behavior

– The green LED stays permanently on.
– The red LED blinks 3 times every 10 seconds.

6.1.2 Standby with at least one transmitter programmed

Device behavior

– The green LED stays permanently on.
– The red LED stays permanently off.

6.2 Normal mode (modes 1 and 2)

6.2.1 Activation of a transmitter in normal mode

Device behavior

– The green LED stays permanently on.
When a matched transmitter is activated:
– The red LED lights up permanently for 10 seconds.
– Relay 1 switches on for 10 seconds.
– Relay 2 stays off.
If the same or another matched transmitter is activated within
10 seconds, the alarm will be retriggered for 10 seconds.

Device behavior when a transmitter has a low battery

– The green LED stays permanently on.
When the transmitter is activated:
– The red LED blinks twice for 2 seconds, then lights up

permanently for 8 seconds. It then blinks once every 10
seconds.

– Relay 1 switches on for 10 seconds.

F.01U.278.517 | V2.0 | 2012.11 User Manual Bosch Security Systems

LE10 Radio Receiver Operation | en 17

– Relay 2 switches on permanently until the battery is

replaced and the transmitter is activated again.

NOTICE!

In normal mode 2, the red LED is deactivated regarding battery­low indication and will not blink every 10 seconds.

Device behavior when the battery is replaced in a transmitter

– The green LED stays permanently on.
When the transmitter is activated:
– The red LED stops blinking every 10 seconds, and lights up

permanently for 10 seconds.
– Relay 1 switches on for 10 seconds.
– Relay 2 switches off.

6.3 Dementia (mode 3)

6.3.1 Activation of a MIYS37L Wristband Transmitter

Device behavior

– The green LED stays permanently on.
When a MIYS37L transmitter is activated:
– The red LED lights up permanently for 7 seconds.
– Relay 1 switches on for 7 seconds.
– 1 second after Relay 1, Relay 2 switches on for 3 seconds.
The procedure is repeated if a MIYS37L transmitter is activated
again.

Device behavior when a MIYS37L transmitter has a low battery

– The green LED stays permanently on.
When the MIYS37L transmitter is activated:
– The red LED blinks twice for 2 seconds and then lights up

permanently red for 5 seconds.
– Relay 1 and Relay 2 behave as above.

Bosch Security Systems User Manual F.01U.278.517 | V2.0 | 2012.11

18 en | Operation LE10 Radio Receiver

6.3.2 Detection of a MIYS37E Wristband Transmitter alone

Device behavior

– The green LED stays permanently on.
When a MIYS37E transmitter is detected:
– The red LED lights up permanently for 30 seconds.
– Relay 1 stays off for 30 seconds.
– Relay 2 switches on for 25 seconds.
During these 30 seconds, all radio reception is fully blocked.
This allows a person wearing the MIYS37E to cross the
monitored area without generating an accompany signal.

6.3.3 Detection of a MIYS37L Wristband Transmitter with a MIYS37E Wristband Transmitter nearby

Device behavior

– The green LED stays permanently on.
When a MIYS37L transmitter and a MIYS37E transmitter are
detected by the monitored area:
– The red LED lights up permanently.
– Relay 1 switches on until the MIYS37E transmitter is

detected.
– 1 second after Relay 1, Relay 2 switches on for 3 seconds.
When the MIYS37E transmitter sends its signal (approx. 4
seconds after the MIYS37L):
– The red LED lights up permanently for 30 seconds.
– Relay 1 switches off for 30 seconds.
– Relay 2 stays on for another 25 seconds.
After the detection of the MIYS37E transmitter, all radio
reception is fully blocked during 30 seconds. This allows a
person wearing the MIYS37E transmitter to accompany a
person wearing the MIYS37L transmitter through the monitored
area without generating an accompany signal.

F.01U.278.517 | V2.0 | 2012.11 User Manual Bosch Security Systems

LE10 Radio Receiver Operation | en 19

6.4 Dementia with Accompany (mode 4)

6.4.1 Activation of a MIYS37L Wristband Transmitter

Device behavior

– The green LED stays permanently on.
When a MIYS37L transmitter is activated, a 10-second time slot
starts.
If, during these 10 seconds, a MIYS37E transmitter is detected:
– There is no change of the LEDs and the relays.
If, during these 10 seconds, no MIYS37E transmitter is
detected:
– The red LED lights up for 2 seconds.
– Relay 1 switches on for 2 seconds.
– Relay 2 stays off.

NOTICE!

In mode 4, there is no battery-low indication.

6.5 Remote control (mode 5)

6.5.1 Activation of a programmed transmitter

Device behavior

– The green LED stays permanently on.
– The red LED lights up.
– Relay 1 switches on.
– Relay 2 stays off.
When the same transmitter is activated again:
– The red LED turns off.
– Relay 1 switches off.

NOTICE!

No other transmitter is able to switch the Relay 1 off, when it
has been already switched on by a transmitter.

Bosch Security Systems User Manual F.01U.278.517 | V2.0 | 2012.11

20 en | Operation LE10 Radio Receiver

6.5.2 Activation of a programmed transmitter with a battery-low message or with a new battery

The behavior of the device is the same as in
Section 6.2.1 Activation of a transmitter in normal mode, page 16.

6.6 Open receiver (modes 6 and 7)

6.6.1 Activation of a transmitter in the reception range

Device behavior

– The green LED stays permanently on.
– The red LED lights up for 10 seconds.
– Relay 1 switches on for 10 seconds.
– Relay 2 switches on for 2 seconds.
Activation of any transmitter during these 10 seconds will
retrigger the procedure.

NOTICE!

In these modes 6 and 7, there is no battery-low indication.

6.7 Daily messages in modes 1, 2 or 5

6.7.1 Daily message with battery-low signal

Device behavior

– The green LED stays permanently on.
Upon receiving a daily message with battery-low signal:
– The red LED blinks every 10 seconds.
– Relay 1 stays off.
– Relay 2 switches on, until the battery is changed.
When the battery is changed, the red LED and Relay 2 switch
off if a daily message or a transmitter activation is detected.

NOTICE!

In Normal mode 2, the red LED is deactivated regarding battery­low indication and will not show any indication.

F.01U.278.517 | V2.0 | 2012.11 User Manual Bosch Security Systems

LE10 Radio Receiver Operation | en 21

6.7.2 Reset of a battery-low indication with button T1

Device behavior

– The green LED stays permanently on.
– The red LED is already blinking every 10 seconds.
Upon pressing button T1 min. 1 second, there is a reset of the
battery-low indication:
– The red LED turns off.
– Relay 2 switches off.

NOTICE!

If you disconnect and reconnect the power supply, the battery­low indication will be reset as well.

6.8 Extended MIYN46 (mode 8, only with SW

1.10)

Programming and deleting of transmitters is done as in Mode 1.

Standby

– The green LED stays permanently on.
– The red LED is off.
– Relay 1 is switched off.
– Relay 2 is switched off.

When a MIYS37 transmitter, MIYS35 transmitter, MIYRAC contact, MIYMD ManDown Sensor are activated:

– The green LED stays permanently on.
– The red LED turns on for 2 seconds.
– Relay 1 is switched on for 2 seconds.
– Relay 2 is switched off.

When a MIYN46 transmitter’s red or blue button is pressed, or when one of its inputs is activated:

– The green LED stays permanently on.
– The red LED and Relay 1 switch on for 6 minutes or until

the green button of the MIYN46 transmitter is pressed.

– Relay 2 is switched off.

Bosch Security Systems User Manual F.01U.278.517 | V2.0 | 2012.11

22 en | Operation LE10 Radio Receiver

NOTICE!

A MIYN46 transmitter in repeated alarm mode extends the
behavior of the LE10 by approximately 26 minutes. If several
MIYN46 transmitters are programmed, each activated
transmitter stops the sequence and starts its own sequence.

Battery-low indication:

– Relay 2 switches on for 2 seconds.
– The red LED flashes for 2 seconds, then blinks 1 second

every 10 seconds.
For all MIYS35 and MIYS37 transmitters, the battery low status
is triggered when the transmitter is activated or with the daily
message. For all MIYN46 transmitters, the battery low status is
triggered only with the daily message.

6.9 Dual channel receiver (mode 9, only with SW 1.10)

Programming and deleting of transmitters is done as in Mode 1.

Standby

– The green LED stays permanently on.
– The red LED is off.
– Relay 1 is switched off.
– Relay 2 is switched off.

When a transmitter, that is matched on a odd position (1, 3, 5, etc.), is activated:

– Relay 1 switches on for 2 seconds.
– The red LED turns on for 2 seconds.

When a transmitter, that is matched on a even position (2, 4, 6, etc.), is activated:

– Relay 2 switches on for 2 seconds.
– The red LED blinks 1 second on, 1 second off, 1 second on.

Battery low indication (until the battery is exchanged)

– The red LED flashes during 2 seconds, then flashes 1

second every 10 seconds.

F.01U.278.517 | V2.0 | 2012.11 User Manual Bosch Security Systems

LE10 Radio Receiver Technical data | en 23

7 Technical data

Dimensions 5.3 x 3.2 x 1.0 inches

(133 x 82 x 26 mm)

Weight 3.9 oz (110 g)

Material ABS

Color Top: white, similar to RAL 9010

Bottom: charcoal

External power supply 8-30 VDC

Current consumption < 25 mA

Outputs 2 relays, with max 28 V DC or

AC, 250 mA maximum

Indication 2 LEDs, one green, one red

Frequency 434.01 MHz

Protection class IP21

Operating temperature range 32°F - 113°F (0°C - 45 °C)

Bosch Security Systems User Manual F.01U.278.517 | V2.0 | 2012.11

Bosch Security Systems

2400 Geng Road, Suite 200
Palo Alto, CA 94303
U.S.A.

www.bosch-telehealth.com

© Bosch Security Systems, 2012