Bosch KBN-335V28-20, KBE-335V55-20, KBN-355V28-20, KBE-355V28-20, KBN-355V55-20 Instruction Manual

KBE and KBN Series

en Instruction Manual

AutoDome, Bilinx, Bosch, the Bosch logo, DiBos, FastAddress and VIDOS are registered trademarks of Bosch Security Systems, inc.
The following trademarks are registered with the United States Patent and Trademark Office:
Pentium is a registered trademark of Intel Corporation
.NET, DirectX, Internet Explorer, Microsoft, Windows, Windows 2000 and Windows XP are registered trademarks of Microsoft Corporation

Due to the nature of this material, this document refers to numerous hardware and software products by their trade names, In most, if not all
cases, these designations are claimed as trademarks or registered trademarks by their respective companies in the United States of America. It is
not this publisher’s intent to use any of these names generically. The reader is therefore cautioned to investigate all claimed trademark rights be­fore using any of these names other than to refer to the product described.

KBE and KBN Series | en iii

Preface

This guide describes how to install the KBE and KBN Series.

Audience

This guide is intended for qualified installation and service personnel who are familiar with the applicable national
and local electrical codes.

Document Conventions

Convention Meaning
Bold Denotes a part, item, or assembly.

Italic Denotes a reference to another paragraph, figure or table.
Underline
courier Denotes the actual name of an object, the exact code that should be typed or a message

Symbols

You may encounter these symbols within the document. Explanatory text accompanies each symbol, which provides
additional information detailing the operation or highlighting safety information.

Used to emphasize a point.

returned from a system.

i

!

!

NOTICE! Notices inform you of essential but non-critical information. Read these messages
carefully as any directions or instructions contained therein can help you avoid making
mistakes.

CAUTION! Cautionary messages provide critical information that help you reduce the chance
of losing data or damaging the system. Please heed these messages.

WARNING! Warnings highlight information, that if overlooked may cause damage to the
system or result in personal injury. Take warnings seriously.

DANGER! Danger messages denote the presence of electrical equipment that may cause
electric shock or electrocution. Take care when you see this symbol to avoid serious injury or
death.

Bosch Security Systems, Inc. Instruction Manual F01U065975 | 1.0 | 2007.04

iv en | KBE and KBN Series

Customer Support and Service

If this unit needs service, contact the nearest Bosch Security Systems Service Center for authorization to return and
shipping instructions.

Service Centers
USA

Phone: [phone] or 585-340-4162
Fax: [phone]
Email: [e-mail]

Technical Support

Phone: [phone]
Email: [e-mail]

CCTV Spare Parts

Phone: [phone] or 408-957-3065
Fax: [phone]
Email: [e-mail]

Canada

Phone: [phone]
Fax: [phone]

Europe, Middle East & Asia Pacific Region

Phone: [phone]
Fax: [phone]
Email: [e-mail]
For additional information, see www.boschsecurity.com

Related Publications

Refer to the latest Bosch Security Systems, Inc. Databook for the most up-to-date datasheets. To obtain a copy of
the Databook, please contact your local Bosch representative.
You can also visit the Bosch Security Systems World Wide Web site at: http://www.boschsecurity.com to view a cur­rent listings of our publications.

F01U065975 | 1.0 | 2007.04 Instruction Manual Bosch Security Systems, Inc.

Important Safeguards

1. Read, Follow, and Retain Instructions - All safety and operating
instructions should be read and followed before operating the unit.
Retain instructions for future reference.

2. Heed Warnings - Adhere to all warnings on the unit and in the operat­ing instructions.

3. Attachments - Attachments not recommended by the product manu­facturer should not be used, as they may cause hazards.

4. Installation Cautions - Do not place this unit on an unstable stand,
tripod, bracket, or mount. The unit may fall, causing serious injury to
a person and serious damage to the unit. Use only manufacturer-rec­ommended accessories, or those sold with the product. Mount the
unit per the manufacturer's instructions. Appliance and cart combina­tion should be moved with care. Quick stops, excessive force, or
uneven surfaces may cause the appliance and cart combination to
overturn.

5. Cleaning - Unplug the unit from the outlet before cleaning. Follow any
instructions provided with the unit. Generally, using a damp cloth for
cleaning is sufficient. Do not use liquid cleaners or aerosol cleaners.

6. Servicing - Do not attempt to service this unit yourself. Opening or
removing covers may expose you to dangerous voltage or other haz­ards. Refer all servicing to qualified service personnel.

7. Damage Requiring Service - Unplug the unit from the main AC power
source and refer servicing to qualified service personnel under the
following conditions:

• When the power supply cord or plug is damaged.

• If liquid has been spilled or an object has fallen into the unit.

• If the unit has been exposed to water and/or inclement weather

(rain, snow, etc.).

• If the unit does not operate normally, when following the operat-

ing instructions. Adjust only those controls specified in the oper­ating instructions. Improper adjustment of other controls may
result in damage, and require extensive work by a qualified techni­cian to restore the unit to normal operation.

• If the unit has been dropped or the cabinet damaged.

• If the unit exhibits a distinct change in performance, this indicates

that service is needed.

8. Replacement Parts - When replacement parts are required, the ser­vice technician should use replacement parts specified by the manu­facturer or that have the same characteristics as the original part.
Unauthorized substitutions may result in fire, electrical shock or
other hazards.

9. Safety Check - Upon completion of servicing or repairs to the unit,
ask the service technician to perform safety checks to ensure proper
operating condition.

| en v

10.Power Sources - Operate the unit only from the type of power source
indicated on the label. If unsure of the type of power supply to use,
contact your dealer or local power company.

• For units intended to operate from battery power, refer to the

operating instructions.

• For units intended to operate with External Power Supplies, use

only the recommended approved power supplies.

• For units intended to operate with a limited power source, this

power source must comply with EN60950. Substitutions may
damage the unit or cause fire or shock.

• For units intended to operate at 24VAC, normal input voltage is

24VAC. Voltage applied to the unit's power input should not

exceed 30VAC.
User-supplied wiring, from the 24VAC supply to unit, must be in com­pliance with electrical codes (Class 2 power levels). Do not ground
the 24VAC supply at the terminals or at the unit's power supply termi­nals.

11.Coax Grounding - If an outside cable system is connected to the unit,
ensure that the cable system is grounded. U.S.A. models only - Sec­tion 810 of the National Electrical Code, ANSI/NFPA No.70, provides
information regarding proper grounding of the mount and supporting
structure, grounding of the coax to a discharge unit, size of grounding
conductors, location of discharge unit, connection to grounding elec­trodes, and requirements for the grounding electrode.

12.Grounding - This unit may be equipped with a 3-wire grounding plug
(a plug with a third pin, for grounding). This safety feature allows the
plug to fit into a grounding power outlet only. If unable to insert the
plug into the outlet, contact an electrician to arrange replacement of
the obsolete outlet. Do not defeat the safety purpose of the ground­ing plug.

• Outdoor equipment should only be connected to the unit's inputs

after this unit has had its grounding plug connected to a grounded
outlet or its ground terminal properly connected to a ground
source.

• The unit's input connectors must be disconnected from outdoor

equipment before disconnecting the grounding plug or grounding
terminal.

• Proper safety precautions such as grounding should be followed

for any outdoor device connected to this unit.

Lightning - For added protection during a lightning storm, or when

13.
this unit is left unattended and unused for long periods of time,
unplug the unit from the wall outlet and disconnect the cable system.
This will prevent damage to the unit due to lightning and power line
surges.

Bosch Security Systems, Inc.

vi en |

For Indoor Product

1. Water and Moisture - Do not use this unit near water ­for example, in a wet basement, in an unprotected out­door installation or in any area classified as a wet loca­tion.

2. Object and Liquid Entry - Never push objects of any
kind into this unit through openings, as they might touch
dangerous voltage points or create short circuits, result­ing in a fire or electrical shock. Never spill liquid of any
kind on the unit.

3. Power Cord and Power Cord Protection - For units
intended to operate with 230VAC, 50Hz, the input and
output power cord must comply with the latest versions
of IEC Publication 227 or IEC Publication 245. Power
supply cords should be routed so they are not likely to
be walked on or pinched. Pay particular attention to
location of cords and plugs, convenience receptacles,
and the point of exit from the appliance.

4. Overloading - Do not overload outlets and extension
cords; this can result in a risk of fire or electrical shock.

For Outdoor Product

Power Lines - An outdoor system should not be located

in the vicinity of overhead power lines, electric lights or
power circuits, or where it may contact such power lines
or circuits. When installing an outdoor system, extreme
care should be taken to keep from touching power lines
or circuits, as this contact might be fatal. U.S.A. models
only - refer to the National Electrical Code Article 820
regarding installation of CATV systems.

For Rack-mount Product

1. Ventilation - Do not place this equipment in a built-in
installation or rack, unless proper ventilation is pro­vided, or the manufacturer's instructions were followed.
The equipment must not exceed its maximum operating
temperature requirements.

2. Mechanical Loading - When rack-mounting the equip­ment, ensure that a hazardous condition is not created
by uneven mechanical loading.

WARNING:
Electrostatic-sensitive device. Use proper CMOS/

MOSFET handling precautions to avoid electro­static discharge.

NOTE: Grounded wrist straps must be worn and
proper ESD safety precautions observed when
handling the electrostatic-sensitive printed circuit
boards.

This symbol indicates the presence of important
operating and maintenance (servicing) instruc­tions in the literature accompanying the appli­ance.

Cover Removal

Warning: Removal of the cover should only be
performed by qualified service personnel - not
user serviceable. The unit should always be
unplugged before removing the cover and remain
unplugged while the cover is removed.

24 VAC Units

Do not exceed 30VAC input. Voltage applied to the unit's
power input should not exceed 30VAC. Normal input voltage is
24VAC. User supplied wiring from 24VAC supply to unit must
be in compliance with electrical codes (Class 2 power levels).
Do not ground 24VAC supply at power supply terminals or at
unit's power supply terminals.

This equipment is to be isolated from the mains
supply by a limited power source as specified in
EN60950.

220-240V, 50Hz Power Cords

220-240V, 50Hz power cords, input and output, must comply
with the latest versions of IEC Publication 227 or IEC Publica­tion 245.

Bosch Security Systems, Inc.

| en vii

FCC & ICES INFORMATION

(U.S.A. and Canadian Models Only)
This device complies with part 15 of the FCC Rules. Operation is subject

to the following two conditions:
(1)This device may not cause harmful interference, and
(2)This device must accept any interference received, including inter-

ference that may cause undesired operation.

NOTE: This equipment has been tested and found to comply with the
limits for a Class A digital device, pursuant to Part 15 of the FCC Rules
and ICES-003 of Industry Canada. These limits are designed to provide
reasonable protection against harmful interference when the equipment
is operated in a commercial environment. This equipment generates,
uses and radiates radio frequency energy, and if not installed and used
in accordance with the instruction manual, may cause harmful interfer­ence to radio communications. Operation of this equipment in a residen­tial area is likely to cause harmful interference, in which case the user
will be required to correct the interference at his expense.

Intentional or unintentional changes or modifications, not expressly
approved by the party responsible for compliance, shall not be made.
Any such changes or modifications could void the user’s authority to
operate the equipment. If necessary, the user should consult the dealer
or an experienced radio/television technician for corrective action. The
user may find the following booklet, prepared by the Federal Communi­cations Commission, helpful: How to Identify and Resolve Radio-TV Inter-
ference Problems. This booklet is available from the U.S. Government
Printing Office, Washington, DC 20402, Stock No. 004-000-00345-4.

WARNING: This is a Class A product. In a domestic environ­ment, this product may cause radio interference, in which
case, the user may be required to take adequate measures.

Safety Precautions

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO
NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE
PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.

This symbol indicates the presence of uninsulated
“dangerous voltage” within the product’s enclo­sure that can cause an electric shock.

This symbol indicates the presence of important
operating and maintenance (servicing) instruc­tions in the literature accompanying the appli­ance.

Installation should be performed by qualified ser­vice personnel only in accordance with the
National Electrical Code or applicable local codes.

Power Disconnect. Units with or without ON-OFF
switches have power supplied to the unit when­ever the power cord is inserted into the power
source; however, the unit is operational only when
the ON-OFF switch is in the ON position. The
power cord is the main power disconnect for all
units.

Bosch Security Systems, Inc.

viii en |

INFORMATIONS FCC ET ICES

(modèles utilisés aux États-Unis et au Canada uniquement)
Ce produit est conforme aux normes FCC partie 15. la mise en service

est soumises aux deux conditions suivantes:
(1) cet appareil ne peut pas provoquer d'interférence nuisible et
(2) cet appareil doit pouvoir tolérer toutes les interférences auxquelles

il est soumit, y compris les interférences qui pourraient influer sur
son bon fonctionnement.

AVERTISSEMENT: Suite à différents tests, cet appareil s’est révélé con­forme aux exigences imposées aux appareils numériques de Classe A en
vertu de la section 15 du règlement de la Commission fédérale des com­munications des États-Unis (FCC). Ces contraintes sont destinées à
fournir une protection raisonnable contre les interférences nuisibles
quand l'appareil est utilisé dans une installation commerciale. Cette
appareil génère, utilise et émet de l'energie de fréquence radio, et peut,
en cas d'installation ou d'utilisation non conforme aux instructions,
générer des interférences nuisibles aux communications radio. L’utilisa­tion de ce produit dans une zone résidentielle peut provoquer des inter­férences nuisibles. Le cas échéant, l’utilisateur devra remédier à ces
interférences à ses propres frais.

Au besoin, l’utilisateur consultera son revendeur ou un technicien quali­fié en radio/télévision, qui procédera à une opération corrective. La bro­chure suivante, publiée par la Commission fédérale des communications
(FCC), peut s’avérer utile : « How to Identify and Resolve Radio-TV Inter­ference Problems » (Comment identifier et résoudre les problèmes
d’interférences de radio et de télévision). Cette brochure est disponible
auprès du U.S. Government Printing Office, Washington, DC 20402,
États-Unis, sous la référence n° 004-000-00345-4.

Avertissement : Ce produit est un appareil de Classe A. Son
utilisation dans une zone résidentielle risque de provoquer
des interférences. Le cas échéant, l’utilisateur devra prendre
les mesures nécessaires pour y remédier.

Sécurité

Attention: l'installation doit exclusivement être réalisée par du

ATTENTION : POUR ÉVITER TOUT RISQUE D'ÉLECTROCU­TION, N'ESSAYEZ PAS DE RETIRER LE CAPOT (OU LE PAN­NEAU ARRIÈRE). CET APPAREIL NE CONTIENT AUCUN
COMPOSANT SUSCEPTIBLE D'ÊTRE RÉPARÉ PAR L'UTILI­SATEUR. CONFIEZ LA RÉPARATION DE L'APPAREIL À DU
PERSONNEL QUALIFIÉ.

Ce symbole signale que le produit renferme une «
tension potentiellement dangereuse » non isolée
susceptible de provoquer une électrocution.

Ce symbole invite l'utilisateur à consulter les
instructions d'utilisation et d'entretien (dépan­nage) reprises dans la documentation qui
accompagne l'appareil.

Attention: l'installation doit exclusivement être
réalisée par du personnel qualifié, conformément
au code national d'électricité américain (NEC) ou
au code d'électricité local en vigueur.

Coupure de l'alimentation. Qu'ils soient pourvus
ou non d'un commutateur ON/OFF, tous les appar­eils reçoivent de l'énergie une fois le cordon
branché sur la source d'alimentation. Toutefois,
l'appareil ne fonctionne réellement que lorsque le
commutateur est réglé sur ON. Le débranchement
du cordon d'alimentation permet de couper l'ali­mentation des appareils.

Bosch Security Systems, Inc.