Bosch ICP-AMAX4-P2-EN, ICP-AMAX4-P3-EN, ICP-AMAX4-P1, AMAX panel 4000, AMAX panel 4000 EN Quick Start Manual

AMAX panel 4000 / AMAX panel 4000 EN

ICP-AMAX4-P1 / ICP-AMAX4-P2-EN / ICP-AMAX4-P3-EN

en Quick Start Guide

Table of contents

1

Short information 4

2

System overview 5

3

Installation 7

3.1 System Power Up 7

3.2 System Status Indicator 7

3.3 Installer and User Code Commands 7

3.4 Prerequisites for Certification conform Installation 9

4

Configuration 10

4.1 Programming with Keypad 10

4.1.1 LCD Keypad Menu Programming 10

4.1.2 LED/Icon LCD Keypad Address Programming 10

4.2 Reset to Factory Default Settings 11

4.3 LCD Menu Programming 12

4.4 Address Programming 20

4.4.1 Communication and Report Setting 20

4.4.2 Zone Programming 26

4.4.3 Output Programming 38

4.4.4 Access Codes 43

4.4.5 System Programming 49

5

Troubleshooting 63

6

Technical Data 66

AMAX panel 4000 / AMAX panel 4000
EN

Table of Contents | en 3

Bosch Sicherheitssysteme GmbH Quick Start Guide 2013.07 | 03 | F.01U.267.113

Short information

Thank you for choosing the AMAX panel 4000. This is a flexible, reliable, convenient, and easy­to-use alarm system. It has 16 wired zones on board, expandable up to 64 wired and wireless
zones.
This Quick start guide is provided with the system to give basic information about the system
wiring, components, and describe how to simply program and operate the system with IUI­AMAX4-TEXT keypad, IUI-AMAX3-LED16 keypad, IUI-AMAX3-LED8 keypad, ICPKP8-LED keypad,
or ICP-KP8L-Icon LCD keypad. As the system includes a large number of programmable
functions and options, we suggest reading the complete installation manual. For detailed
operation method, please refer to the User Guide.

1

4 en | Short information

AMAX panel 4000 / AMAX panel 4000

EN

2013.07 | 03 | F.01U.267.113 Quick Start Guide Bosch Sicherheitssysteme GmbH

System overview

Information:

Customer:

Location:

Account #:

Installe r:

Date:

2

AMAX panel 4000 / AMAX panel 4000
EN

System overview | en 5

Bosch Sicherheitssysteme GmbH Quick Start Guide 2013.07 | 03 | F.01U.267.113

Wiring Diagram

Pro

gram Key Port

GND

-

+

A C

A

C

Transformer

Battery

Tam

per

L2 COM

COM

COM

L1a

L3

L4

L5

L6

L7

L8

L9

COM

COM

COM

COM

L10

L11

L12

L13

L14

L15

L16

P0+4

R

B

G

Y

AUX1

-

AUX2

-

AUX1
+12V

Y

G

B

R

RINGRHTHTIP

L1b

P0+3

P0+

P0-2

P0-1

Zones

Bosch Option
Bus 2 < 900mA

+12V

+

0 V

1

2

3

3

1 Tamper Switch
2 Zone Switch
3 EOL 2,2 k

3

2

3

2

Fuse 1 A

PO+4: < 750mA
PO+3: < 750mA
PO -2: < 500mA
PO -1: < 500mA

230V ~50Hz
230mA

Wac

hdog

outpu

t

<100

mA

12V < 18Ah

18VAC@50VA

Zones

AUX 1: < 900mA
AUX 2: < 900mA

AUX Power

Fir

e

Intrusion

Risk of shock if N,L1 or is connected incorrectly.
For operation safety, the ground terminals must
be connected.

3

3

2

Slow flash: Normal state
On: Trouble state
Off: Trouble state

_

_

_
_

_

_

_

_

+12V

+12V

+12V

COM

_

12V 7Ah

AUX2
+12V

_

COM

supervised

PO-5

Z1

2

2

3

3

Keypads:

IUI-AMAX4-TEXT
IUI-AMAX3-LED16
IUI-AMAX3-LED8

Keypads:
IUI-AMAX-LED8
IUI-AMAX-LCD8

I/O Moduls:
DX2010 Adr. 103 - 108
DX3010 Adr. 150 - 151
DX4010 Adr. 253

Communicators:
DX4020G Adr. 134
B426 Adr. 134(6) / 250(9)

RF Receiver:
RF3227E 1=
RFRC-OPT 1= (1)

1 =

2

=

3 =

4

=

1 =
2 =

Bosch Option
Bus

1 < 900

mA

COM

R

B

G

Y

R

B

G

Y

R

B

G

Y

♥

IUI-AMAX3

+4 Keypad

3

1

2

1

Facto

ry

Default

5-16 Inst. Guide

I
2000mA

100 Ω - 2,2 k

_

<

∑

3

6 en | System overview

AMAX panel 4000 / AMAX panel 4000

EN

2013.07 | 03 | F.01U.267.113 Quick Start Guide Bosch Sicherheitssysteme GmbH

Installation

This system / product must be installed by a qualified installer / service person.
During installation and wiring, the control panel power source must be switched-off to prevent
equipment damage.
– To switch off the Power Source, an easy accessible circuit breaker must be available.
– The System / product must be connected to a socket-outlet with a protective earthing

contact
The User has to disconnect all Telecommunication Network Connectors before unplugging the
power adaptor
After the control panel wiring is completed, connect the AC power and backup batteries.
The power light on the keypad will light to show that AC power is connected.

Notice!

- Use only non spillable battery

- Battery must be recycled and disposed of properly

- When battery is not replaced correctly risk of fire explosion or burning

Notice!

The system must be installed and maintained by qualified installer / service person.
Bosch recommends testing the whole alarm system at least once a week.
Maintenance should be done by qualified installer / service person four times a year.

System Power Up

After the system is powered up, set date and time. Otherwise, the system prompts as fault.
After the system is powered up or reset, it resets to previous arming / disarming status.
To reduce false alarms caused by system power-up (or by power supply restoration after both
mains supply and AUX power supply fail), the system is designed to not perform zone test
within one minute after power-up.

System Status Indicator

The system status is indicated by the LED status indicator on the system main board.
Slow flash of red status indicator (repeating on and off with an interval of 1 second) indicates
normal system operation.

Installer and User Code Commands

The system supports programmable 4- to 6-digit Installer and User Code to execute the
following programming and operating commands.
The installer commands can be used only when all areas of the system are in disarming status
with no alarm activated and when installer access is enabled from user.

Notice!

No identical User Codes are allowed. User Codes are not permitted to be the same as
Installer codes.

3

3.1

3.2

3.3

AMAX panel 4000 / AMAX panel 4000
EN

Installation | en 7

Bosch Sicherheitssysteme GmbH Quick Start Guide 2013.07 | 03 | F.01U.267.113

User Code Commands

Function

(Default User Code = 2580

Default Inst. Code = 1234)

Command

Duress User

Arming User

Basic User

Super User

Master User

Instal. User

S witc h to M ai n K ey pa d [C od e] + [ 0][0 ][0 ] + [# ] (T ext KP ) √ √

S witc h to P ar titi on 01 -16 [C od e] + [ 0][ _ ] [ _ ] + [#] (T ext KP ) √ √

A W AY arm [C od e] + [ 1][1 ] + [# ] / [Co de ] + [# ] / [# ] (Q u ick arm ) √ √ √ √ √ √

S TAY a rm [C od e] + [ 1][2 ] + [# ] / [Co de ] + [*] / [* ] (Q ui ck arm ) √ √ √ √ √ √

D isa rm [C od e] + [ #] √ √ √ √ √

D isp lay In fo ( Fa ult /Ta mp er. .) [C od e] + [ -] √ √

Keypad Emergency Alarm

Keypad Fire

Keypad Medical Alarm Long press [7] and [9]

Fa ul t/Ta m pe r In qu ire [C od e] + [ 2][1 ] + [# ] √ √ √

Check All Event Log

[C od e] + [ 2][2 ] + [# ] √ √ √

Check EN Event Log

[C od e] + [ 2][3 ] + [# ] (T ex t K P) √ √ √

Check Dialer Event Log

[C od e] + [ 2][4 ] + [# ] (T ex t K P) √ √ √

Zone Bypass/Cancel

[Code] + [3][1] + [#] + [Zone No] [*] + [#] (Bypass)

√ √ √ √

[Code] + [3][1] + [#] + [Zone No] [*] + [#] (Cancel LED)

√ √ √ √

[Code] + [3][2] + [#] + [Zone No] [*] + [#](Cancel Text KP)

√ √ √ √

Bypass Inquire

[Code] + [3][3] + [#] (Text KP)

√ √ √ √

B ypa ss Fa ult /Ta mp er [C od e] + [ 3][4 ] + [# ] √ √ √ √

S iren te st [C od e] + [ 4][1 ] + [# ] √ √ √

C om mu nic at ion te st [C od e] + [ 4][2 ] + [# ] √ √ √

W al k t est [ Co de ] + [4] [3] + [ #] √ √ √

C han ge /V iew da te /tim e [C od e] + [ 5][1 ] + [# ] √

D ayl igh t S avi ng Tim e (+1 h) [C od e] + [ 5][2 ] + [# ] √ √ √

D ayl igh t S avi ng Tim e (-1 h) [C od e] + [ 5][3 ] + [# ] √ √ √

A dd / D ele te / C ha nge U se r [C od e] + [ 5][4 ] + [# ] √ √

C han ge In div idu al Co de [C od e] + [ 5][5 ] + [# ] √ √ √ √ √ √

C han ge D om es tic Ph on e N o.1

[C od e] + [ 5][6 ][# ] + [ _ _ _ _ _ _ ] [#] (LE D KP ) √

C han ge D om es tic Ph on e N o.2

[C od e] + [ 5][6 ][# ][# ] + [ _ _ _ _ _ _ ] [#] (LE D KP ) √

C han ge D om es tic Ph on e N o.3

[C od e] + [ 5][6 ][# ][# ][# ] + [ _ _ _ _ _ _ ] [#] (LE D KP ) √

C han ge D om es tic Ph on e N o.4

[C od e] + [ 5][6 ][# ][# ][# ][#] + [ _ _ _ _ _ _ ][ #] ( LE D K P ) √

C han ge D om es tic Ph on e N o.1 -4 [C ode ] + [5 ][6 ][# ] + [_] + [ #] + [ _ _ _ _ _ _ ][# ] (T ex t K P) √

C all Ba ck [C od e] + [ 5][7 ] + [# ] √

C han ge La ng ua ge

[C od e] + [ 5][8 ] + [# ] + [ _ ] [ _ ] + [ #]
01 =E N 02 =D E 03 =E S 04 =F R
05 =I T 06 =P L 07 =N L 08 =S E

√ √ √

R ese t t am pe r o r fa ult [C ode ] + [6 ] + [# ] √ √ √

Installer Access

[Code] + [7][1] + [#] (Enable)
[Code] + [7][2] + [#] (Disable)

√

S yst em re set [C od e] + [ 9][9 ][8 ][9 ] + [#] √ √ √

In sta lle r p rog ram m od e [C od e] + [ 9][ 5][ 8] + [# ] √

E xits Pr og r. m od e with ou t s av e [9 ][5 ][9] + [#]

(o nly in Ad re ss Pro gr. M ode )

√

E xits Pr og r. m od e with s ave [ 9][ 6][0 ] + [# ]

(o nly in Ad res s P ro gr. Mo de )

√

S et F ac tor y D ef aul ts [9 ][6 ][1] + [#]

(o nly in Ad re ss Pro gr. M ode )

√

C opy co nt rol pa ne l da ta to pro gr . K ey [9 ][6 ][2] + [#]

(o nly in Ad re ss Pro gr. M ode )

√

C opy p rog r. k ey da ta to con tro l p an el. [ 9][ 6][3 ] + [# ]

(o nly in Ad res s P ro gr. Mo de )

√

D isp lay FW ver sio n [9 ][9 ][9] + [#]

(on ly in A dr ess P rog r. M od e)

√

Long press [1] and [3] or [*] and [#]

Long press [4] and [6]

Figure 3.1: User Code Commands

8 en | Installation

AMAX panel 4000 / AMAX panel 4000

EN

2013.07 | 03 | F.01U.267.113 Quick Start Guide Bosch Sicherheitssysteme GmbH

Prerequisites for Certification conform Installation

EN 50131-3 Grade 2, Environmental Class 2

– System must be placed inside the monitored area on a stable surface.
– Keypads must be mounted to the inner side of the monitored area.
– Once the system is tested and ready to use, Enclosure Door and Accessory Enclosures

must be secured with the provided screws
– To realize EN conform Alarm Indication and Transmission, one of the following options

must be used

– Two supervised Warning devices (PO-1 PO-2 & PO+) and one ATS 2 Communicator

(onboard Dialer, B426, D4020 or DX4020G)

– One self powered Warning Device and one ATS 2 Communicator (onboard Dialer,

B426, D4020 or DX4020G)

– Two Communicators, one ATS 2 (onboard Dialer, B426, D4020 or DX4020G) and one

ATS 1 (onboard Dialer, B426, D4020 or DX4020G)

– One ATS 3 Communicator (DX4020 or B426)
All Communicators must be connected to a Central Monitoring Station.
Only the onboard Dialer and the Option Bus Communicators can be used for EN Alarm
Transmission.
– one 12V/7AH or one 12V/18Ah Battery must be connected to the System.
– max current for all components with a 7Ah Battery = 550mA
max current for all components with a 18Ah Battery = 1500mA
(standby 12h, recharge Battery 80% in 72h)
(PCB=l00mA, IUI-AMAX Keypads=31mA, DX2010=35mA, DX3010=10mA, B426=100mA,
DX4020G=65mA, RF3227E=30mA, RFRC-OPT=30mA)
– To realize EN conform Arming procedure an indication of arm/disarm status must be

accessible from outside the monitored area (this indication can be time limited)
– To realize EN conform Access to the Monitored Area, one of the following options must

be used

– Opening a door (to the entry/exit route) must start the entry procedure

– Indication of arm/disarm Status

– Access to the monitored Area (doors not starting entry procedure) is prevented (e.g.

door strike, mechanically)
The Enclosure lock can only be used in non EN setup.
– Telephone arming can only be used in non EN setup.
– Accessory Modules, except input module (DX2010) can be used only inside the enclosure

(on the adapter plate).

– When input module (DX2010) is used in the external enclosure (AE20) the tamper skirt

must be installed on the PCB of input module (DX2010)

– The panel must be programmed with the EN settings indicated on the programming

sheet. When the panel is set without EN parameters, the EN Indication (on Label) must
be removed.

3.4

AMAX panel 4000 / AMAX panel 4000
EN

Installation | en 9

Bosch Sicherheitssysteme GmbH Quick Start Guide 2013.07 | 03 | F.01U.267.113

Configuration

The control panel programming options are stored in a non-volatile flash memory. This
memory has all relevant configuration and user-specific data even after a total power loss.
Because the data retention time is quite long without power, reprogramming is not required
after powering up the control panel.
Programming with keypad is possible only when all of zones in the system are in disarmed
status and no alarm is activated. Installer Code is required for programming.

Notice!

It is not recommended to use other keypads or methods simultaneously to program the
system while programming with the current keypad.

Programming with Keypad

LCD Keypad Menu Programming

1. Enable Text keypad and confirm that the system is in disarmed status.

2. Enter Installer Code + [958] and press [#] to get to [Installer Menu].

3. Programming: Select the menu and operate according to the menu prompt.
– Down to the next menu: Press [▼]
– Up to the previous menu: Press [▲]
– Enter menu or confirm input: Press [#]
– Back to the menu or delete a single input: Press [-]; or press and hold [-] for 3

seconds to end the input state and get back to the menu.

– Operate according to the menu prompt. Select menu and enter data for specific

programming items according to the display on the keypad to complete
programming, step by step.

– The data value ranges in the menu programming and address programming are the

same. For specific options and value ranges, see contents in LCD Keypad Menu
Programming, page 10.

4. After completing input, press [-] to get back to the previous menu. Complete all
programming input by repeating step 3 and press [-] to get back to the current main
menu level by level.

5. Press [-] to enter menu options. It is optional to save or not to save the programming
information.

6. Select [Save and Exit] and press [#] to save system programming data, exit menu
programming and reset system.

LED/Icon LCD Keypad Address Programming

1. Enable LED keypad or Icon LCD keypad and make sure that the system is in disarmed
status.

2. Enter programming mode: Enter the Installer Code (the default is 1234) + [958] and
press [#].

3. Programming: Move to the required address and enter the value for each data bit (data
value).
– After entering programming mode, the system directly enters the programming data

in the address 0000 (Receiver 1 telephone number or the initial digit of the IP
address), then

4

4.1

4.1.1

4.1.2

10 en | Configuration

AMAX panel 4000 / AMAX panel 4000

EN

2013.07 | 03 | F.01U.267.113 Quick Start Guide Bosch Sicherheitssysteme GmbH

– Enter the next address: Press [#]
– Back to the previous address: Press [*]
– Skip to other address: Enter the address code and press [#]
– Set new data in the address: Enter new data values and press [*]
– Enter new data values as required. Otherwise, the factory Default will be used in the

system.

4. Exit programming mode: Enter Command [9] [6] [0] and press [#] to save programming
data. Entering [9] [5] [9] + [#] means not to save the programming data.

For LED/Icon LCD keypad, the programming data is displayed by the keypad indicator. See
Programming Data Indicators, page 11.

Notice!

For LED/Icon LCD keypad, when the programming data exceeds the display range of the
keypad indicator, there will be no display on the keypad.

Programming Data Indicators

Data Zone Indicators

Value 1 2 3 4 5 6 7 8 Mains

0

1 X

2 X

3 X

4 X

5 X

6 X

7 X

8 X

9 X X

10 X

11 X X

12 X X

13 X X

14 X X

15 X X

Reset to Factory Default Settings

The factory Default can be reset with the ‘Resetting to Factory Default’ pads on the main
board of the control panel.

1. Disconnect the AC power supply and backup battery to the control panel.

2. Short-circuit the ‘Resetting to Factory Default’ pads.

3. These set of pads are located at the top on the printed circuit board of the control panel.

4.2

AMAX panel 4000 / AMAX panel 4000
EN

Configuration | en 11

Bosch Sicherheitssysteme GmbH Quick Start Guide 2013.07 | 03 | F.01U.267.113

4. Powering up is done when the bonding pads are short-circuited.

5. Quick flash of the red LED indicator on the printed circuit board of the control panel
indicates that the factory Default will be reset.

6. All programming parameters are reset to factory default immediately after releasing the
short-circuited bonding pads.

Notice!

If the DEFAULT pads are short-circuited for over 10 seconds after power-up, the control panel
will discard resetting to factory Default.

LCD Menu Programming

For menu programming with LCD keypad, see Section 4.1.1 LCD Keypad Menu Programming
on page 10.
Use [▼] and [▲] to move main menus, submenus and secondary submenus up or down.
Use [-] and [#] to move main menus, submenus and secondary submenus left or right.

4.3

12 en | Configuration

AMAX panel 4000 / AMAX panel 4000

EN

2013.07 | 03 | F.01U.267.113 Quick Start Guide Bosch Sicherheitssysteme GmbH

COPY DATA TO KEY

FUNCTION VIEW

FAULT ANALYSIS

RF SETTING

RF RECEIVER

RF SENSOR DIAGNOSE

CLR ALL RF DEVICES

SIREN SETTINGS

ZONE FUNCTION

QUICK ARM ONLY */#

INSTALLER ACCESS

EVENT RECORD COUNT

SYSTEM SETTING

ADD/DELETE ZONE

PULSE COUNT DURAT.

RING TIMES

CODE SETTING

RPC IP/PORT/DHCP

INSTALLER MENU

COM+REPORT SETTING

RECEIVER SETTING

REPORT SETTING

RF LOW BATT REPEAT

SIREN BEEP AR/DIS

ADDRESS PROGRAM

COPY DATA TO PANEL

ADDRESS/KEY PROGR

RF DEVICE MANAGER

RF USER

RF REPEATER DIAGN.

RF REPEATER

RF JAM DETECT LEV.

RF KEYFOB PANIC AL

RF SUPERVISION

OUTPUT SETTINGS

RF PARA. SETTING

FORCE ARM FAULT/TA

FW VERSION

OUTPUT SETTING

SYS TAMPER INDIC.

DATE/TIME

FACTORY DEFAULT

LANGUAGE VERSION

KP 2 BUTTON ALARM

KP TONE/LOCKOUT

FUNCTION SETTING

FAULT CONFIG

KEYPAD AREA

AREA TIMING

COMMON AREA

CROSS TIMER

ZONE SETTING

TEST REPORT DURAT.

DUAL IP

REMOTE ACCESS

DOMESTIC/CALLBACK

INSTALLER CODE

CODE PERMISSIONS

KP/AREA SETTING

CODE LENGTH

USER CODE

Figure 4.1: Menu Structure

!

Warning!

Programming parameters must be set within the value range in the programming address.
Otherwise, the system will turn to indeterminate status.

AMAX panel 4000 / AMAX panel 4000
EN

Configuration | en 13

Bosch Sicherheitssysteme GmbH Quick Start Guide 2013.07 | 03 | F.01U.267.113

ZN RESTORE REPORT

AWAY REPORT

STAY REPORT

SYSTEM STAT REPORT

PANIC REPORT

FIRE REPORT

MEDICAL REPORT

AUTOM. TEST REPORT

REPORT EXP. TIME:m

TEST RPT INTERV: h

TEST REPORT: hour

AUTOM. TEST REPORT

TEST REPORT DURAT.

DUAL IP SETTING

REM. ACCESS ARMED

REMOTE PROGRAMMING

DUAL IP

REMOTE ACCESS

RPC IP/PORT/DHCP

IP ADDRESS

PORT No

DHCP UPDATE TIME:h

CALLBACK SETTING

DOMEST/CALLBACK No

DOMESTIC/CALLBACK

RING COUNT

RING TIMES

COM+REPORT SETTING

RECEIVER SETTING

INPUT RECEIVER No

PHONE/IP PORT No

SUBSCRIBER ID No

REPORT SETTING

FORMAT

NETWORK ANTIREPLAY

ACK WAIT TIME: sec

NETW. POLLING: min

Figure 4.2: Com+Report

14 en | Configuration

AMAX panel 4000 / AMAX panel 4000

EN

2013.07 | 03 | F.01U.267.113 Quick Start Guide Bosch Sicherheitssysteme GmbH

CODE PERMISSIONS

TAMPER RESET USER

ARM/DISARM INSTAL.

CHANGE INST. CODE

CODE LENGTH

CODE LENGTH

USER CODE IN AREA

CHANGE USER CODE

INSTALLER CODE

USER CODE

INPUT USER No

USER CODE PRIORITY

CODE SETTING

Figure 4.3: Code Setting

PULSE COUNT DURAT.

CROSS TIMER

CROSS ZN TIMER:sec

ZONE FUNCTION

ZONE IN AREA

PULSE COUNT DURAT.

ADD/DELETE ZONE

INPUT ZONE No

ZONE MODULE SEL.

ZONE STATUS REPORT

UNVERF.REP/CROS.ZN

ZONE DOMESTIC

ZONE PULSE COUNT

ZONE LOCKOUT

ZONE TAMPER

ZONE TYPE

FORCE ARM/BYPASS

SILENT AL./CHIME

ZONE SETTING

ZONE FUNCTION

ZONE FUNCTION No

Figure 4.4: Zone Setting

AMAX panel 4000 / AMAX panel 4000
EN

Configuration | en 15

Bosch Sicherheitssysteme GmbH Quick Start Guide 2013.07 | 03 | F.01U.267.113

KEYPAD IN AREA

AREA TIMING

INPUT AREA No

EXIT DELAY: sec

KP/AREA SETTING

KEYPAD AREA

INPUT KEYPAD No

ENTRY DELAY: sec

COMMON AREA

COMMON AREA

KP TONE/LOCKOUT

KEYPAD ALARM TONE

KEYPAD LOCK COUNT

Figure 4.5: KP Area Setting

16 en | Configuration

AMAX panel 4000 / AMAX panel 4000

EN

2013.07 | 03 | F.01U.267.113 Quick Start Guide Bosch Sicherheitssysteme GmbH

FAULT ANALYSIS

FW VERSION

DEFAULT PANEL YES

DEFAULT PANEL NO

FUNCTION VIEW

SYS TAMPER INDIC.

SYS TAMP. ALL AR.

FACTORY DEFAULT

1-EN 3-ES 6-PL 8SE

KP 2 BUTTON ALARM

KP 2 BUTTON AL

LANGUAGE VERSION

1-EN 6-PL

only one is

2-DE 4-FR 5-IT 7NL

displayed (P1-3)

FORCE ARM FAULT/TA

EVENT RECORD COUNT

EVENT RECORD COUNT

INSTALLER ACCESS

INSTALLER ACCESS

FORCE ARM FAULT/TA

SIREN SUPERVISED

QUICK ARM ONLY */#

QUICK ARM ONLY */#

DISABLE FAULT REPO

BATT. CHK INTERVAL

PHO. LN SUPERVISED

FAULT CONFIG

KEYPAD FAULT SOUND

AC FAULT REP. TIME

FUNCTION SETTING

DATE/TIME

CHANGE DATE/TIME

SYSTEM SETTING

Figure 4.6: System Setting

AMAX panel 4000 / AMAX panel 4000
EN

Configuration | en 17

Bosch Sicherheitssysteme GmbH Quick Start Guide 2013.07 | 03 | F.01U.267.113

IN SIREN IND. EN

SIREN OFF ON KEY

SIREN SETTINGS

SIREN TIME: min

SIREN BEEP ENABLE

OUTPUT AREA / ZONE

OUTPUT MODE

OUTPUT TIME: sec

OUTPUT SETTINGS

ENTER OUTPUT No

OUTPUT EVENT TYPE

OUTPUT SETTING

Figure 4.7: Output Setting

18 en | Configuration

AMAX panel 4000 / AMAX panel 4000

EN

2013.07 | 03 | F.01U.267.113 Quick Start Guide Bosch Sicherheitssysteme GmbH

KEYFOB ID: MANUAL

RF SENSOR DIAGNOSE

RF ZONE No:

REPEATERID: MANUAL

RF USER

KEYFOB No: 1-128

RF DEVICE MANAGER

RF REPEATER

REPEATER No: 1-8

SIREN BEEP AR/DIS

REMOTE ARM PROMPT:

RF KEYFOB PANIC AL

SIGNAL JAM DETECT:

RF LOW BATT REPEAT

LOW BATT. REPEAT:

RF SUPERVISION

RF DEVICE SUPERV:

RF JAM DETECT LEV.

RF PARA. SETTING

RF RECEIVER

RF RECEIVER ENABLE

RF SETTING

CLEAR CONFIRM

CLEAR CANCEL

CLR ALL RF DEVICES

RF REPEATER DIAGN.

REPEATER No: 1-8

SIGNAL STRENGTH:

DEVICE STATE:

SIGNAL STRENGTH:
DEVICE STATE:

Figure 4.8: RF Setting

COPY DATA TO KEY

ADDRESS/KEY PROGR

ADDRESS PROGRAM

ADDR[ ]VALUE=

COPY DATA TO PANEL

Figure 4.9: Address Key Program

AMAX panel 4000 / AMAX panel 4000
EN

Configuration | en 19

Bosch Sicherheitssysteme GmbH Quick Start Guide 2013.07 | 03 | F.01U.267.113

Address Programming

Communication and Report Setting

Report Options Address Default

Telephone Number / IP Address and Port for Receiver 1 0000 - 0016 15

Subscriber ID Number 0017 - 0022 000000

Transmission Format for Receiver (0 = Not used, 1 =
Contact ID, 2= SIA, 3 = Conettix IP)

0023 1

Anti-replay for Receiver (0 = Disabled, 1 = Enabled) 0024 1

EN=1

Acknowledge Wait Time for Receiver (05 - 99 seconds ) 0025 - 0026 05

Network Polling Time for Receiver (001 - 999 minutes ) 0027 - 0029 001

Telephone Number / IP Address and Port for Receiver 2 0030 - 0046 15

Subscriber ID Number 0047 - 0052 000000

Transmission Format for Receiver (0 = Not used, 1 =
Contact ID, 2= SIA, 3 = Conettix IP)

0053 1

Anti-replay for Receiver (0 = Disabled, 1 = Enabled) 0054 1

EN=1

Acknowledge Wait Time for Receiver (05 - 99 seconds ) 0055 - 0056 05

Network Polling Time for Receive (001 - 999 minutes) 0057 - 0059 001

Telephone Number / IP Address and Port for Receiver 3 0060 - 0076 15

Subscriber ID Number 0077 - 0082 000000

Transmission Format for Receiver (0 = Not used, 1 =
Contact ID, 2= SIA, 3 = Conettix IP)

0083 1

Anti-replay for Receiver (0 = Disabled, 1 = Enabled) 0084 1

EN=1

Acknowledge Wait Time for Receiver (05 - 99 seconds) 0085 - 086 05

Network Polling Time for Receiver (001 - 999 minutes) 0087 - 089 001

Telephone Number / IP Address and Port for Receiver 4 0090 - 0106 15

Subscriber ID Number 0107 - 0112 000000

Transmission Format for Receiver (0 = Not used, 1 =
Contact ID, 2= SIA, 3 = Conettix IP)

0113 1

Anti-replay for Receiver (0 = Disabled, 1 = Enabled) 0114 1

EN=1

Acknowledge Wait Time for Receiver (05 - 99 seconds) 0115 - 0116 05

Network Polling Time for Receiver (001 - 999 minutes) 0117 - 0119 001

4.4

4.4.1

20 en | Configuration

AMAX panel 4000 / AMAX panel 4000

EN

2013.07 | 03 | F.01U.267.113 Quick Start Guide Bosch Sicherheitssysteme GmbH

Notice!

Enter telephone number when the Contact ID or SIA format is selected; enter IP address and
port number when the Bosch Network format is selected. Anti-replay for Receiver,
Acknowledge Wait Time for Receiver and Network Polling Time for Receiver are valid only
when using Bosch Network format.

Setting Telephone Number
For telephone number programming, See Telephone Programming Parameters, page 26
Setting IP Address and Port Number
The IP address is programmed with the 17 digits: Digits 1 - 12 for the IP address of the
receiver; 13 - 17 for the port.
It is not necessary to enter dots in programming, but 0 must be entered ahead of the digit to
make up 3 digits when each IP address unit is fewer than 3 digits. 0 must be entered ahead of
the digit to make up 5 digits when the port is fewer than 5 digits.
Example:
Receiver IP address 128.73.168.7, port 7700, should be made as: 128 073 168 007 07700

Dual IP Settings

Option

Address Default

0 = 1 IP module, 1 = 2 IP modules 0120 1

Notice!

Dual IP Settings are valid only when used in the Connetix IP format. This programming option
is valid for B426 and ITS-DX4020-G modules. ITS-DX4020-G cannot be set as No. 2 IP module.

Module Address

ITS-DX4020-G module or B426- module 1 134

B426 module 2 250

System Reporting

Option Address Default

Zone Status Restore Report 0121 6

AWAY Arming / Disarming Report 0122 6

EN=1/5/6/7

STAY Arming / Disarming Report 0123 6

EN=1/5/6/7

System Status Report (Zone fail, comm. fail, telephone
line fail, AC fail, low batterie...etc.)

0124 6

EN=1/5/6/7

Keypad Panic Alarm Report 0125 0

Keypad Fire Alarm Report 0126 0

Keypad Medical Alarm Report 0127 0

AMAX panel 4000 / AMAX panel 4000
EN

Configuration | en 21

Bosch Sicherheitssysteme GmbH Quick Start Guide 2013.07 | 03 | F.01U.267.113

Automatic Test Report 0128 6

EN=1/5/6/7

0 = No report, 1 = Receiver 1, 2 = Receiver 2, 3 = Receiver 3, 4 = Receiver 4, 5 = Receiver
1,2,3 and 4, 6 = Receiver 1 (2,3 and 4 for backup), 7 = Receiver 1 (2 for backup) and receiver
3 (4 for backup)

Notice!

When the Transmission Format for Receiver in the receiver programming is set to 0 (not
used), i.e., setting the report option as sending report to a receiver, then the alarm control
panel will actually not send any report.

Automatic Test Report

Address 0129 - 0134 Address Default

Test Report Time: Interval
00 = Do not use timing report , 01 - 99 = 1 - 99 hours

0129 - 0130 24

VDS-A

EN=1=24

Report Time: Hour
00 - 23 = 0 - 23 hours, Others = Do not use real-time
report

0131 - 0132 99

Report Time: Minute
00 - 59 = 0 - 59 minutes, Others = Do not use real-time
report

0133 - 0134 99

Report Expiry Time

Address 0135 - 0137

Address Default

000 = No time limit, 001 - 255 = 1 - 255 minutes 0135 - 0137 000

VDS-A

EN=000

Installer Access Until Next Arming

Address

0138 Address Default

0 = disabled, 1 = enabled 0138 0

VDS-A=1

Force Arm When System Is In Trouble Condition

Address

0139 Address Default

0 = disabled, 1 = enabled 139 1

VDS-A EN=0

Siren / PO 1+2 Supervision

Address

0140 Address Default

0 = disabled, 1 = PO1 enabled, 2 = PO2 enabled, 3 =
PO1+2 enabled

0140 0

VDS-A EN=3

22 en | Configuration

AMAX panel 4000 / AMAX panel 4000

EN

2013.07 | 03 | F.01U.267.113 Quick Start Guide Bosch Sicherheitssysteme GmbH