Bosch HEZCMT3050 Installation manual
Installation
Instructions
HEZCMT3050 COFFEE MAKER TRIM KIT
BOSCHAPPLIANCES.COM
Table of
Safety
Contents
Safety ......................................................................................2
Important Safety Instructions.......................................... 2
Installation with a Warming Drawer........................................ 3
Before You Begin............................................................3
General Dimensions........................................................ 3
Cabinet Cutout Dimensions............................................3
Flush Install Dimensions.................................................. 4
Installation with a Warming Drawer................................ 4
Stand-Alone Installation..........................................................8
Before You Begin............................................................8
General Dimensions........................................................ 8
Cabinet Cutout Dimensions............................................8
Flush Install Dimensions.................................................. 9
Stand-Alone Installation..................................................9
Definitions
9 WARNING
This indicates that death or serious injuries may occur as a
result of non-observance of this warning.
9 CAUTION
This indicates that minor or moderate injuries may occur as a
result of non-observance of this warning.
NOTICE: This indicates that damage to the appliance or
property may occur as a result of non-compliance with this
advisory.
Note: This alerts you to important information and/or tips.
Page. 1
This Bosch® appliance is made by
BSH Home Appliances Corporation
1901 Main Street, Suite 600
Irvine, CA 92614
Questions?
1-800-735-4328
www.bosch-home.com/us
We look forward to hearing from you!
Safety
IMPORTANT SAFETY
INSTRUCTIONS
READ AND SAVE
THESE INSTRUCTIONS
INSTALLER: Please leave these instructions with this unit for the owner. Show the owner the location of the circuit breaker or fuse. Mark it for easy reference.
OWNER: Please retain these instructions for future
reference.
WARNING
When properly cared for, your new appliance has been
designed to be safe and reliable. Read all instructions
carefully before use. These precautions will reduce the
risk of burns, electric shock, fire and injury to persons.
When using kitchen appliances, basic safety precautions
must be followed, including those in the following pages.
WARNING
DO NOT repair or replace any part of the appliance
unless specifically recommended in the manuals.
Improper installation, service or maintenance can cause
injury or property damage. All other servicing should be
done by an authorized servicer.
WARNING
It is the responsibility of the owner and the installer to
determine if additional requirements and/or standards
apply to specific installations.
ELECTRIC SAFETY
Before you plug in an electrical cord, be sure all controls
are in the OFF position.
For appliances equipped with a cord and plug, DO NOT
cut or remove the ground prong. It must be plugged into
a matching grounding type receptacle to avoid electrical
shock. If there is any doubt as to whether the wall
receptacle is properly grounded, the customer should
have it checked by a qualified electrician.
If required by the National Electrical Code (or Canadian
Electrical Code), this appliance must be installed on a
separate branch circuit.
Be sure your appliance is properly installed and grounded
by a qualified electrician. Installation, electrical
connections and grounding must comply with all
applicable codes.
RELATED EQUIPMENT SAFETY
Remove all tape and packaging before using the
appliance. Destroy the packaging after unpacking the
appliance. Never allow children to play with packaging
material.
Never modify or alter the construction of the appliance.
For example, do not remove leveling legs, panels, wire
covers or anti-tip brackets/screws.
State of California Proposition 65 Warning:
This product can expose you to chemicals including vinyl
chloride, which is known to the State of California to
cause cancer and birth defects or other reproductive
harm. For more information go to
www.P65Warnings.ca.gov.
APPLIANCE HANDLING SAFETY
CAUTION
It is recommended to have two installers to
install the coffee maker. Failure to do so may
result in property damage or personal injury.
Hidden surfaces may have sharp edges. Use caution when
reaching behind or under appliance.
GROUNDING INSTRUCTIONS
WARNING
Improper grounding can result in a risk of electric shock.
This appliance must be grounded. In the event of an
electrical short circuit, grounding reduces the risk of
electric shock by providing an escape wire for the electric
current. This appliance is equipped with a cord having a
grounding wire with a grounding plug. The plug must be
plugged into an outlet that is properly installed and
grounded.
Page. 2
Installation with a Warming Drawer
29¾" (755)
13
¾" (349)
14¾" (374)
17
(449)
11
/16
"
23½" (596)
22" (558)
17
⅞"
(455)
19⅝"
(498)
inches (mm)
28½"
(724)
inches (mm)
Before You Begin
Trim Kits
Trim kits are designed for use ONLY with the Built-in
Coffee Maker models BCM8450UC.
IMPORTANT: The Built-in Coffee Maker installation
instructions can be found in the Built-in Coffee Maker
Assembly. The coffee maker must be installed according
to the instructions in the Installation Instructions. If the
instructions are not followed, this may result in
unsatisfactory installation or unit performance.
Tools Needed
• Phillips head screwdriver
• Torx T-20 screwdriver
• Measuring tape
• Drill with bits (1/16")
Screws Included with the Coffee Maker Trim Kit
8 x
#8 x ¾'' Wood Screw (Phillips)
General Dimensions
Cabinet Cutout Dimensions
Items Used Included with BCM8450UC Coffee Maker
7 x
14 x
1 x
4 x
Spacer
M4 x 25mm Screw (T20 Torx)
#10 x ½ Screw (T20 Torx)
Shims
23½"
(597)
28½"
28½"
(724)
(724)
28⅝"
(727)
Page. 3
Flush Install Dimensions
Top View
Side View
reveal
cleat
29⅛"
(740)
ush
cut-out
height
24½"
(622)
ush inset
depth
¾" (19)
¾" (19)
reveal
cleat
reveal
cleat
1" (25)
1"
(25)
28½" (724)
30¾" (781)
8
(218)
"
9
/16
23½" (622)23½" (622)23½" (622)
*
inches (mm)
dia. 1/16"
1
2
dia. 1/16"
1
2
Installation with a Warming
Drawer
Mounts above a HWD5051UC Warming Drawer.
1. Install Warming Drawer according to the Warming
Drawer Installation Instructions.
2. Install the Left Cabinet Mounting Bracket at the top
left of the cabinet opening using two (2) ¾'' Phillips
head wood screws. Ensure the bracket is flush to the
cabinet side and cabinet face.
NOTE: * Flush installation requires a 5/16'' (8 mm) high x
28½'' (724 mm) wide x 22½'' (571 mm) deep baseplate
underneath the unit body.
3. Install the Right Cabinet Mounting Bracket at the top
right of the cabinet opening using two (2) ¾'' Phillips
head wood screws. Ensure the bracket is flush to the
cabinet side and cabinet face.
Page. 4
4. Measure 1½'' (38 mm) from top edge of warming
1½" (38)1½" (38)1½" (38)
dia. 1/16"
1
drawer and make mark on both sides of cabinet.
5. Install the Left and Right Side Cabinet Brackets flush
to the cabinet face with two (2) ¾'' Phillips head wood
screws per side. Install side trim mounting bracket so
that the bottom edge of the bracket is aligned with
the pencil mark.
7. Secure the two (2) Warming Drawer Clearance
Brackets to the top of the installed warming drawer
using the outer holes with six (6) ½'' T-20 Torx head
screws.
8. Secure the Left Side Mounting Bracket to the Left
Cabinet Mounting Bracket using one (1) ½'' T-20 Torx
screw.
6. Secure the Left Side Mounting Bracket to the Left
Side Warming Drawer Clearance Bracket using three
(3) x
½'' T-20 Torx head screws.
Page. 5
9. Secure the two (2) Transformer Support Brackets to
the Warming Drawer Clearance Brackets with four
(4) ½'' T-20 Torx head screws.
10. Set the Coffee Maker Transformer on top of the
Transformer Support Brackets.
11. Plug the transformer plug into the back of the coffee
maker, as instructed in the Coffee Maker Installation
Instructions. Slide coffee maker in cabinet on top of
the Base Plate and move coffee maker to the left so
the left side is flush with the Left Support Bracket.
13. Use a 1'' T-20 Torx screw with spacer (shipped with
coffee maker) to secure the top right corner of the
coffee maker.
14. If the door does not shut smoothly, check to see if the
Door Latch is hitting on the top or bottom or the
receiver.
12. Open the coffee maker door. Secure the Left Support
Bracket from the inside of the coffee maker using six
(6) x 1'' T-20 Torx head screws.
Page. 6
15. If the latch is hitting on the bottom, pull the coffee
1mm 2mm
3mm
4mm
maker out and install the 1mm Shim, included with the
coffee maker, at the bottom left side of the coffee
maker.
If the receiver is hitting on the top, install the 1mm
Shim on the top left of the coffee maker.
16. Reinstall the coffee maker. If the receiver hits again
increase the shim size until the Door Latch no longer
hits.
17. Press the Built-in Coffee Maker Trim Kit into the Left
and Right Side Cabinet Brackets.
Page. 7
Stand-Alone Installation
29¾" (755)
13
¾" (349)
14¾" (374)
17
(449)
11
/16
"
23½" (596)
22" (558)
17
⅞"
(455)
19⅝"
(498)
inches (mm)
28½"28½"28½"
(724)(724)(724)
19⅞" – 23½"
(504 – 597)
19⅞" – 23½"
(504 – 597)
19⅞" – 23½"
(504 – 597)
19¼"
(488)
inches (mm)
Before You Begin
Trim Kits
Trim kits are designed for use ONLY with the Built-in
Coffee Maker models BCM8450UC.
IMPORTANT: The Built-in Coffee Maker installation
instructions can be found in the Built-in Coffee Maker
Assembly. The coffee maker must be installed according
to the instructions in the Installation Manual. If the
instructions are not followed, this may result in
unsatisfactory installation or unit performance.
Tools Needed
• Phillips head screwdriver
• Torx T-20 screwdriver
• Measuring tape
• Drill with bits (1/16")
Screws Included with the Coffee Maker Trim Kit
8 x
#8 x ¾'' Wood Screw (Phillips)
General Dimensions
Cabinet Cutout Dimensions
7 x
10 x
Items Used Included with BCM8450UC Coffee Maker
1 x
4 x
Spacer
M4 x 25mm Screw (T20 Torx)
#10 x ½ Screw (T20 Torx)
Shims
Page. 8
Flush Install Dimensions
*
Top View
Side View
reveal cleats
20⅛"
(511)
ush
cut-out
height
ush inset
depth
¾" (19)¾" (19)
reveal
cleats
reveal
cleats
1" (25)
1"
(25)
28½" (724)
30" (762)
19⅞" – 23½"
(504 – 597)
19⅞" – 23½"
(504 – 597)
19⅞" – 23½"
(504 – 597)
19
⅞
" – 23½"
(504 – 597)
19⅞" – 23½"
(504 – 597)
19⅞" – 23½"
(504 – 597)
inches (mm)
dia. 1/16"
1
2
dia. 1/16"
1
2
1⅝" (41)1⅝" (41)1⅝" (41)
dia. 1/16"
1
2
2. Install the Right Cabinet Mounting Bracket at the top
right of the cabinet opening using two (2) ¾'' Phillips
head wood screws. Ensure the bracket is flush to the
cabinet side and cabinet face.
NOTE: * Flush installation requires a 5/16'' (8 mm) high x
28½'' (724 mm) wide x 22½'' (571 mm) deep baseplate
underneath the unit body.
Stand-Alone Installation
1. Install the Left Cabinet Mounting Bracket at the top
left of the cabinet opening using two (2) ¾'' Phillips
head wood screws. Ensure the bracket is flush to the
cabinet side and cabinet face.
3. Measure 1
⅝'' (41 mm) from cabinet base and make
mark on both sides of cabinet.
4. Install the Left and Right Side Cabinet Brackets flush
to the cabinet face with two (2) ¾'' Phillips head wood
screws per side. Install side trim mounting bracket so
that the bottom edge of the bracket is aligned with
mark.
Page. 9
5. Secure the Left Side Mounting Bracket to the Base
CCC
LL
dia. 1/16"
1
Plate using three (3) T-20 x
½'' Torx head screws.
6. Center the Base Plate in the cabinet cavity using the
center locating notch. Secure the Base Plate to the
cabinet floor with six (6) ¾” Phillips head wood
screws.
8. Set the Coffee Maker Transformer behind the Base
Plate. Install and plug transformer according to the
Coffee Maker instructions.
9. Plug the transformer plug into the back of the coffee
maker, as instructed in the Coffee Maker Installation
Instructions. Slide coffee maker in cabinet on top of
the Base Plate and move coffee maker to the left so
the left side is flush with the Left Support Bracket.
7. Secure the Left Side Mounting Bracket to the Left
Cabinet Mounting Bracket at the top left of the
cabinet using one (1) T-20 x
½'' Torx head screw.
10. Open the coffee maker door. Secure the Left Support
Bracket from the inside of the coffee maker using six
(6) x 1'' T-20 Torx head screws.
Page. 10
11. Use a 1'' T-20 Torx screw with the spacer (shipped with
1mm 2mm
3mm
4mm
coffee maker) to secure the top right corner of the
coffee maker.
12. If the door does not shut smoothly, check to see if the
Door Latch is hitting on the top or bottom or the
receiver.
13. If the latch is hitting on the bottom, pull the coffee
maker out and install the 1mm Shim, included with the
coffee maker, at the bottom left side of the coffee
maker.
If the receiver is hitting on the top, install the 1mm
Shim on the top left of the coffee maker.
14. Reinstall the coffee maker. If the receiver hits again
increase the shim size until the Door Latch no longer
hits.
15. Press the Built-in Coffee Maker Trim Kit into the left
and right Side Cabinet Brackets.
Page. 11
Loading...