Bosch EN4216R User Manual
Intrusion Alarm Systems | EN4216R Wireless LCD Receiver
EN4216R Wireless LCD Receiver
www.boschsecurity.com
u Monitors up to 16 transmitters or repeaters
u Text display (LCD)
u Cost-effective solution for small systems
u Flexible alarm and fault output
u Wireless registration
The EN4216R LCD Receiver integrates up to sixteen
900 MHz wireless transmitters into any application.
The Inovonics EchoStream platform uses diversity
reception and advanced signal processing to reduce
dead spots in transmission areas. The liquid crystal
display (LCD) allows the user to view the current
status of all transmitters and view the history of
events. Each receiver stores up to 50 events. The
receiver provides versatile options for adding high
performance wireless to an installation.
System overview
Powered by Inovonics
The Inovonics EchoStream platform, powered by
Inovonics wireless mesh network technology, ensures
superior range, reliability, and scalability for
commercial applications. Using a wide range of
transmitters and repeaters, this proven technology
provides flexibility and performance to meet the most
stringent requirements. This exclusive protocol is
available only on Inovonics EchoStream products.
Wireless 900 MHz Band
The Inovonics EchoStream platform sends redundant
information on several multi-frequency channels within
the FCC Part 15 900 MHz band, providing superior
range and reliability. In comparison, systems that use a
single frequency technology can only send information
on one narrow band channel. Any interference within
the band can cause missed signals. With wireless
registration, it is easy to add this technology to any
application.
Functions
Flexible Outputs
Transmitters and repeater faults and alarms map to
any of the receiver models.
Wireless Registration
There is no external programmer required. The
transmitter is enrolled using a wireless programming
routine built into the receiver. Wireless registration
reduces installation time.
Secure Wireless Implementation
Jam detection monitors all channels for the presence
of interference for more than 20 sec. A reset terminal
is inside the receiver, allowing the receiver to accept
external reset signals. The receiver includes a case
tamper and internal antennas for added security.
Status Indication
The LCD shows the current condition of each
transmitter. The LCD also provides a history of past
events including activation, tamper, low battery, and
inactivity.
Supervision and Expansion
Transmitter supervisory check-in and a transmitter
specific supervisory window, defined in the receiver,
support sites with both removable pendants and fixedposition transmitters. The technology also supervises
repeaters.
Enroll, supervise, and map up to sixteen wireless
transmitters and repeaters using the appropriate
outputs. Configure transmitters and repeaters
individually to best suit the application.
Certifications and approvals
Inovonics Wireless Corporation holds the following approvals:
FCC Conforms to FCC Part 15 regulations
Installation/configuration notes
Compatibility Information
The EN4216R LCD Receiver is compatible with the
following products:
Repeater
EN5040‑T High‑power Repeater
Transmitters
EN1210 Universal Transmitter (Single‑input)
EN1210EOL Universal Transmitter with EOL Resistor
EN1210SK Survey Transmitter
EN1210W Door-Window Transmitter with Reed Switch
EN1215EOL Universal Transmitter with Wall Tamper and
EOL Resistor
EN1215WEOL Door‑Window Transmitter with Wall Tamper,
Reed Switch, and EOL Resistor
EN1223D Water-resistant Pendant Transmitter
(Double‑button)
EN1223S Water-resistant Pendant Transmitter
(Single‑button)
EN1223SK Survey Pendant Transmitter
EN1233D Necklace Pendant Transmitter (Double‑button)
EN1233S Necklace Pendant Transmitter (Single‑button)
EN1235D Beltclip Pendant Transmitter (Double‑button)
EN1235S Beltclip Pendant Transmitter (Single‑button)
EN1235DF Fixed-location Transmitter (Double‑button)
EN1235SF Fixed-location Transmitter (Double‑button)
EN1242 Smoke Detector-Transmitter
EN1247 Glass-break Sensor Transmitter
EN1249 Billtrap Transmitter
EN1260 PIR Motion Sensor‑Transmitter (Commercial
and High‑end Domestic Applications)
EN1261HT PIR Motion Sensor‑Transmitter (High‑traffic
Areas)
EN1262 PIR Motion Sensor‑Transmitter (Residential and
Low‑traffic Commercial Applications)
EN1265 PIR Motion Sensor‑Transmitter (Ceiling‑mount
Applications)
Parts included
Quant. Component
1 EN4216R Receiver
1 Hardware pack
1 Literature – Installation and Operation Manual
Technical specifications
Electrical
Power Requirements: 10 VDC to 14 VDC
Environmental
Relative Humidity: Up to 90%, non‑condensing
Temperature (operating ): 0°C to +60°C (+32°F to +140°F)
Mechanical
Material: ABS
Closure: Latching with optional screws for high
security installations
Dimensions: 16.5 cm x 8.9 cm x 2.5 cm (6.5 in. x 3.5
in. x 1 in.)
Weight: 204 g (7.2 oz)
Outputs
Rating: 1 A, 28 VDC, or 0.5 A, 30 VAC (resistive)
Types: • Six on‑board Form C relays for
connecting to any control panel
or for stand-alone wireless
applications (NO or NC)
• One NO Receiver case tamper
contact closure
• One NC Receiver jam input
indication
Reception Characteristics
Frequency Compatibility: 902 MHz to 928 MHz
Transmitters: Supports up to 16
Trademarks
Trademark names are used throughout this document.
In most cases, these designations are claimed as
trademarks or registered trademarks in one or more
countries by their respective owners. Rather than
placing a trademark symbol in every occurrence of a
trademark name, Bosch Security Systems, Inc. uses
2
| EN4216R Wireless LCD Receiver
Loading...