Bosch DWB98PR50, DWB98PR55 User manual and assembly instructions
3FHJTUFS
QHZGHYLFHRQ
0\%RVFKQRZDQG
JHWIUHHEHQHILWV
CPTDIIPNFDPN
XFMDPNF
\RXU
Extractor hood
[en] Instructions for installation and use Extractor hood
Table of contents
[en]I n st r u ct i ons f or i ns t all at i on and useExt r ac t or hood
en
INSTRUCTION MANUAL ..........................................................3
8 Intended use ......................................................... 3
( Important safety information .............................. 4
7 Environmental protection.................................... 6
Ç Operating modes.................................................. 6
1 Operating the appliance ...................................... 7
e Connecting to a hob ............................................ 9
o Home Connect.................................................... 10
INSTRUCTION MANUAL
2 Cleaning and maintenance................................ 12
3 Trouble shooting................................................ 14
4 Customer service ............................................... 14
INSTALLATION INSTRUCTIONS...........................................16
( Important safety information ............................ 16
K General information ........................................... 18
5 Installation .......................................................... 19
Produktinfo
Additional information on products, accessories,
replacement parts and services can be found at
www.bosch-home.com and in the online shop
www.bosch-eshop.com
8Intended use
I nt ended use
Read these instructions carefully. Only then
will you be able to operate your appliance
safely and correctly. Retain the instruction
manual and installation instructions for future
use or for subsequent owners.
The appliance can only be used safely if it is
correctly installed according to the safety
instructions. The installer is responsible for
ensuring that the appliance works perfectly at
its installation location.
This appliance is intended for domestic use
and the household environment only. The
appliance is not intended for use outside. Do
not leave the appliance unattended during
operation. The manufacturer is not liable for
damage which is caused by improper use or
incorrect operation.
This appliance is intended for use up to a
maximum height of 2000 metres above sea
level.
This appliance may be used by children over
the age of 8 years old and by persons with
reduced physical, sensory or mental capacity
or by persons with a lack of experience or
knowledge if they are supervised by someone
who is responsible for their safety, or have
been instructed in how to use the appliance
safely and have understood the risks involved
in not using it properly.
Children must not play with the
appliance.Cleaning and user maintenance
must not be performed by children unless they
are over 15 years of age and are supervised.
Keep children below the age of 8 years old at
a safe distance from the appliance and power
cable.
Check the appliance for damage after
unpacking it. Do not connect the appliance if it
has been damaged in transport.
This appliance is not intended for operation
with an external clock timer or a remote
control.
3
en Important safety information
(Important safety
information
Impor t ant saf et y i nf or mat i on
:Warning – Danger of suffocation!
Packaging material is dangerous to children.
Never allow children to play with packaging
material.
:Warning – Danger of death!
Risk of poisoning from flue gases that are
drawn back in.
Always ensure adequate fresh air in the room
if the appliance is being operated in exhaust
air mode at the same time as room airdependent heat-producing appliance is being
operated.
Room air-dependent heat-producing
appliances (e.g. gas, oil, wood or coaloperated heaters, continuous flow heaters or
water heaters) obtain combustion air from the
room in which they are installed and discharge
the exhaust gases into the open air through an
exhaust gas system (e.g. a chimney).
In combination with an activated vapour
extractor hood, room air is extracted from the
kitchen and neighbouring rooms - a partial
vacuum is produced if not enough fresh air is
supplied. Toxic gases from the chimney or the
extraction shaft are sucked back into the living
space.
■ Adequate incoming air must therefore
always be ensured.
■ An incoming/exhaust air wall box alone will
not ensure compliance with the limit.
Safe operation is possible only when the
partial vacuum in the place where the heatproducing appliance is installed does not
exceed 4 Pa (0.04 mbar). This can be
achieved when the air needed for combustion
is able to enter through openings that cannot
be sealed, for example in doors, windows,
incoming/exhaust air wall boxes or by other
technical means.
In any case, consult your responsible Master
Chimney Sweep. He is able to assess the
house's entire ventilation setup and will
suggest the suitable ventilation measures to
you.
Unrestricted operation is possible if the vapour
extractor hood is operated exclusively in the
circulating-air mode.
:Warning – Risk of fire!
■ Fatty deposits in the grease filter may catch
fire. Regularly clean the grease filter. Never
operate the appliance without a grease
filter.
Risk of fire!
■ Grease deposits in the grease filter may
catch fire. Never work with naked flames
close to the appliance (e.g. flambéing). Do
not install the appliance near a heatproducing appliance for solid fuel (e.g.
wood or coal) unless a closed, nonremovable cover is available. There must
be no flying sparks.
Risk of fire!
■ Hot oil and fat can ignite very quickly. Never
leave hot fat or oil unattended. Never use
water to put out burning oil or fat. Switch off
the hotplate. Extinguish flames carefully
using a lid, fire blanket or something similar.
Risk of fire!
■ When gas burners are in operation without
any cookware placed on them, they can
build up a lot of heat. A ventilation
appliance installed above the cooker may
become damaged or catch fire. Only
operate the gas burners with cookware on
them.
Risk of fire!
■ Operating several gas burners at the same
time gives rise to a great deal of heat. A
ventilation appliance installed above the
cooker may become damaged or catch fire.
Never operate two gas burners
simultaneously on the highest flame for
longer than 15 minutes. One large burner of
more than 5 kW (wok) is equivalent to the
power of two gas burners.
4
Important safety information en
:Warning – Risk of burns!
■ The accessible parts become very hot when
in operation. Never touch hot parts. Keep
children at a safe distance.
Risk of burns!
■ The appliance becomes hot during
operation. Allow the appliance to cool down
before cleaning.
:Warning – Risk of injury!
■ Components inside the appliance may have
sharp edges. Wear protective gloves.
Risk of injury!
■ Items placed on the appliance may fall
down. Do not place any objects on the
appliance.
Risk of injury!
■ The light emitted by LED lights is very
dazzling, and can damage the eyes (risk
group 1). Do not look directly into the
switched on LED lights for longer than 100
seconds.
:Warning – Risk of electric shock!
■ A defective appliance may cause electric
shock. Never switch on a defective
appliance. Unplug the appliance from the
mains or switch off the circuit breaker in the
fuse box. Contact the after-sales service.
Risk of electric shock!
■ Incorrect repairs are dangerous. Repairs
may only be carried out and damaged
power cables replaced by one of our
trained after-sales technicians. If the
appliance is defective, unplug the appliance
from the mains or switch off the circuit
breaker in the fuse box. Contact the aftersales service.
Risk of electric shock!
■ Do not use any high-pressure cleaners or
steam cleaners, which can result in an
electric shock.
Risk of electric shock!
■ Penetrating moisture may result in an
electric shock. Clean the appliance using a
damp cloth only. Before cleaning, pull out
the mains plug or switch off the circuit
breaker in the fuse box.
Causes of damage
Caution!
Risk of damage due to corrosion. Always
switch on the appliance while cooking to avoid
condensation. Condensate can produce
corrosion damage.
Always replace faulty bulbs to prevent the
remaining bulbs from overloading.
Risk of damage due to ingress of humidity into
the electronic circuitry. Never clean operator
controls with a wet cloth.
Surface damage due to incorrect cleaning.
Clean stainless steel surfaces in the direction
of the grain only. Do not use any stainless
steel cleaners for operator controls.
Surface damage due to strong or abrasive
cleaning agents. Never use strong and
abrasive cleaning agents.
Risk of damage from returning condensate.
Install the exhaust duct in such a way that it
falls away from the appliance slightly (1°
slope).
Risk of damage as a result of incorrect
loading of design elements. Do not pull design
elements.Do not place objects on the design
elements or hang objects from them.
Caution!
There is a risk of surface damage if you do not
peel off the protective film.Remove the
protective film from all parts of the appliance
before using the appliance for the first time.
5
en Environmental protection
7Environmental protection
Envi r onmental pr ot ec t i on
Your new appliance is particularly energy-efficient.
Here you can find tips on how to save even more
energy when using the appliance, and how to dispose
of your appliance properly.
Saving energy
■ During cooking, ensure that there is a sufficient
supply of air to enable the extractor hood to work
efficiently and with a low level of operating noise.
■ Adjust the fan speed to the amount of steam
produced during cooking. Only use intensive mode
when required. The lower the fan speed, the less
energy is consumed.
■ If cooking produces large amounts of steam, select
a higher fan speed in good time. If the cooking
steam has already spread around the kitchen, the
extractor hood will need to be operated for longer.
■ Switch off the extractor hood if you no longer require
it.
■ Switch off the lighting if you no longer require it.
■ Clean and (if required) replace the filter at regular
intervals in order to increase the effectiveness of the
ventilation system and to prevent the risk of fire.
■ Put the lid on to reduce cooking steam and
condensation.
ÇOperating modes
Operat i ng modes
Exhaust air mode
The air which is drawn in is cleaned
by the grease filters and conveyed to
the exterior by a pipe system.
Note: The exhaust air must not be conveyed into a
functioning smoke or exhaust gas flue or into a shaft
which is used to ventilate installation rooms which
contain heat-producing appliances.
■ Before conveying the exhaust air into a non-
functioning smoke or exhaust gas flue, obtain the
consent of the heating engineer responsible.
■ If the exhaust air is conveyed through the outer wall,
a telescopic wall box should be used.
Circulating-air mode
The air which is drawn in is cleaned by
the grease filters and an activated
carbon filter and conveyed back into the
kitchen.
Environmentally-friendly disposal
Dispose of packaging in an environmentally-friendly
manner.
This appliance is labelled in accordance with
European Directive 2012/19/EU concerning
used electrical and electronic appliances
(waste electrical and electronic equipment WEEE). The guideline determines the
framework for the return and recycling of used
appliances as applicable throughout the EU.
Note: To bind odours in circulating-air mode, you must
install an activated carbon filter. The different options for
operating the appliance in circulating-air mode can be
found in the brochure. Alternatively, ask your dealer.
The required accessories are available from specialist
retailers, from customer service or from the Online
Shop.
6
Operating the appliance en
1Operating the appliance
Operat i ng t he appl i ance
These instructions apply to several appliance variants.
It is possible that individual features are described
which do not apply to your appliance.
Control panel
Symbol Explanation
#
1-3 Fan settings
C
D
y
>
#
D
B
Fan on/off
Intensive mode 1
Intensive mode 2
Fan run-on
Automatic mode
Metal grease filter/activated charcoal filter saturation
indicator
Home Connect
Light on/off/dimming
If your appliance has Home Connect, more functions
are only available in the Home Connect app.
Note: Switch on the extractor hood when you start
cooking and switch it off again several minutes after you
have finished cooking. This is the most effective way of
removing the kitchen fumes.
Fan run-on time
Switching on
Touch the
The fan will run at fan setting 1.
After approximately 10 minutes, the fan will switch itself
off automatically.
Switching off
Touch the y symbol.
This immediately stops fan run-on.
y symbol.
Automatic mode
Setting the fan
Switching on
Touch the # symbol.
The fan will start at fan setting 2.
Selecting a fan setting
Select the fan setting.
Switching off
Touch the # symbol.
Intensive setting
You can use the intensive setting if there is a large
build-up of odours and fumes/vapours.
Switching on
Touch the C or D symbol.
Note: After approx. 6 minutes, the extractor hood
automatically switches back to fan setting 3.
Switching off
If you want to end intensive mode before the preset
time expires, touch the symbol for the required fan
setting.
Switching on
1. Touch the # symbol.
The fan will start at setting 2.
2. Touch the > symbol.
The optimum fan setting is set automatically using
the PerfectAir sensor.
Switching off
Touch # or any fan setting to switch off automatic
mode.
The fan switches itself off automatically if the PerfectAir
sensor detects no further change in the air quality in the
room.
Automatic mode can run for a maximum of 4 hours.
7
en Operating the appliance
Sensor control
In automatic mode, the PerfectAir sensor in the
extractor hood detects the intensity of the cooking and
roasting odours. Depending on the setting of the
PerfectAir sensor, the fan automatically switches itself to
another fan setting.
Possible sensor settings:
Default sensitivity setting:
„ (fan setting 3)
Lowest sensitivity setting: ‚ (fan setting 1)
Highest sensitivity setting: † (fan setting D)
If the sensor controller responds too strongly or not
enough, it can be changed accordingly:
1. Touch and hold the > symbol when the fan is
switched off. The setting will be displayed.
2. The sensor controller setting can be changed by
touching symbols 1, 2, 3,
3. Take your finger off the > symbol.
C or D.
Saturation display
If the metal grease filters or the activated charcoal filter
are/is saturated, the corresponding symbols flashes
after the appliance is switched off:
Lighting
The lighting can be switched on and off independently
of the fan.
Touch the
B symbol.
Setting the brightness
Press and hold the B symbol until the required
brightness is reached.
Audible signal
Switching on
Touch and hold the
time for approximately 3 seconds when the fan is
switched off. An audible signal will sound as an
acknowledgement.
Switching off
Touch and hold the # and y symbols at the same
time for approximately 3 seconds when the fan is
switched off. An audible signal will sound as an
acknowledgement.
# and y symbols at the same
■ Metal grease filters: # and 1
■ Activated charcoal filter: # and 2
■ Metal grease filter and activated charcoal filter: #,
1 and 2
If you have not yet done so, the metal grease filters
should now be cleaned or the activated charcoal filter
replaced. ~ "Cleaning and maintenance" on page 12
Note: The saturation indicator does not apply for non-
renewable activated charcoal filters that are inserted
downstream of the metal grease filter. These activated
charcoal filters must be replaced twice a year.
The saturation indicators can be reset while they are
flashing. To do this, touch the # symbol.
Switching over the display for air recirculation mode
For air recirculation mode, the electronic controller must
be switched over accordingly:
■ The extractor hood must be connected and switched
off.
■ Touch and hold the D symbol. Touch the "2"
symbol.Take your finger off the D symbol. This
will switch the electronic controller over to air
recirculation mode (filters that cannot be
regenerated).
■ Touch and hold the D symbol. Touch the "3"
symbol.Take your finger off the D symbol. This
will switch the electronic controller over to air
recirculation mode (filters that can be regenerated).
■ Repeatedly touching and holding the D symbol
and touching the "1" symbol switches the electronic
controller back over to air extraction mode.
8
Loading...