Page 1
EN
Operating and installation instructions GP4U
BORA GP4 induction cooktop
with integrated cooktop extractor - recirculation
004136-10002
www.bora.com
www.bora.com/service/installation-GP4U
Page 2
EN
Table of Contents
1 General information 3
1.1 Liability ............................................................................. 3
1.2 Validity of the operating and installation instructions ... 3
1.3 Product conformity ......................................................... 3
1.4 Presentation of information............................................ 3
2 Safety 4
2.1 Use as intended ............................................................... 4
2.2 People with limited abilities ........................................... 4
2.3 General safety instructions ............................................ 4
2.4 Safety instructions for installation ................................. 5
2.5 Safety instructions – operation ...................................... 7
2.6 Safety instructions – cleaning and maintenance ......... 9
2.7 Safety instructions – repairs, servicing and
spare parts ....................................................................... 9
2.8 Safety instructions – disassembly and disposal .......... 9
3 Technical data 11
4 Appliance description 12
4.1 System description ........................................................12
4.1.1 Structure ........................................................................ 12
4.1.2 Operating panel and operating principle........................ 12
4.1.3 Functions ........................................................................ 13
4.2 How the cooktop extractor works – recirculation ...... 13
4.3 How the induction cooking zone works ......................13
4.3.1 Suitable cookware .......................................................... 13
5 Installation 14
5.1 Scope of delivery ........................................................... 14
5.2 Tool and aids ..................................................................14
5.3 Assembly instructions ...................................................14
– Safety clearances .........................................................14
– GP4U minimum unit dimensions ...................................15
– Return flow of recirculated air .......................................15
5.4 Preparing kitchen units ................................................. 15
– GP4U installation dimensions .......................................15
5.5 Creating the worktop cut-out .......................................16
5.6 Installing the appliance ................................................. 17
5.7 Establishing the power connection ..............................19
5.7.1 Function test .................................................................. 20
5.8 Sealing the appliance .................................................... 20
5.9 Handover to user ...........................................................20
6.3 Safety devices ................................................................23
6.3.1 Childproofing feature ..................................................... 23
6.3.2 Residual heat indicator ................................................... 24
6.3.3 Safety shut-down ........................................................... 24
6.4 Saving energy ................................................................24
7 Cleaning and maintenance 25
7.1 Cleaning agents ............................................................. 25
7.2 Looking after the cooktop ............................................ 25
7.3 Cleaning the cooktop .................................................... 25
7.4 Cleaning the cooktop extractor ....................................25
7.5 Cleaning the air guiding housing..................................26
7.6 Changing the activated charcoal filter.........................27
8 Troubleshooting 29
9 Decommissioning,
disassembly and disposal 30
9.1 Decommissioning .......................................................... 30
9.2 Disassembly ................................................................... 30
9.3 Environmentally-friendly disposal ................................ 30
10 Warranty, technical service,
spare parts, accessories 31
10.1 BORA manufacturer’s warranty....................................31
10.1.1 Warranty extension ........................................................ 31
10.2 Service ............................................................................ 31
10.3 Spare parts .................................................................... 31
10.4 Accessories .................................................................... 31
6 Functions and operation 21
6.1 Cooktop ......................................................................... 21
6.1.1 Switching the cooktop on/off ........................................ 21
6.1.2 Switching the cooking zone on/off ............................... 21
6.1.3 Power levels ................................................................... 21
6.1.4 Power setting ................................................................. 21
6.1.5 Timer functions .............................................................. 22
– Short-time timer (egg timer) .........................................22
– Cooking zone timer.......................................................22
6.1.6 Pan size recognition ....................................................... 22
6.2 Cooktop extractor .........................................................22
6.2.1 Switching the cooktop extractor on/off ........................ 22
6.2.2 Power levels ................................................................... 23
6.2.3 Power setting ................................................................. 23
6.2.4 Automatic after-run ........................................................ 23
6.2.5 Filter service display ...................................................... 23
– Changing the filter ........................................................23
– Resetting the filter service display ................................23
2
www.bora.com
Page 3
1 General information
General information
EN
These instructions contain important information to protect you
from injury and prevent damage to the appliance.
Please read these instructions carefully before installing or using
the appliance for the first time.
Other documents apply alongside these instructions.
Please by all means adhere to all documents that form part of
the scope of delivery.
Assembly, installation and commissioning must always occur
in line with national laws, regulations and standards. The work
must be performed by qualified specialists who are familiar with
and comply with the supplementary regulations of the local
utility companies.
All safety and warning information as well as the handling
instructions in the accompanying documents must be observed.
1.1 Liability
BORA Holding GmbH, BORA Vertriebs GmbH & Co KG, BORA
APAC Pty Ltd and BORA Lüftungstechnik GmbH – hereinafter
referred to as BORA – does not assume any liability for damage
arising from disregard for or non-adherence to the documents
included in the scope of delivery!
Furthermore, BORA shall not be held liable for damage caused
by improper installation or failure to observe the safety and
warning instructions!
1.2 Validity of the operating and
installation instructions
These instructions apply to several appliance versions. It is
therefore possible that some of the features described do not
apply to your appliance. The details of the figures contained
herein may differ from some appliance versions and are to be
understood as schematic diagrams.
1.3 Product conformity
Directives
The appliances meet the following EU/EC directives:
2014/30/EU EMC Directive
2014/35/EU Low Voltage Directive
2009/125/EC Ecodesign Directive
2011/65/EU RoHS Directive
1.4 Presentation of information
We use standard formatting, numbering, symbols, safety
instructions, terms and abbreviations so that you can work
quickly and safely when using this manual.
The term “appliance” is used to refer to cooktops, cooktop
extractors or cooktops with integrated cooktop extractor.
Instructions are indicated with an arrow.
X
Always follow all instructions in the prescribed order.
Enumerations are indicated with a bullet point at the start of
the line:
O
Enumeration 1
O
Enumeration 2
Information notes point to special features that must be
i
taken into account.
Safety and warning instructions
The safety and warning instructions in this manual are
emphasised with symbols and signal words.
Safety and warning instructions are structured as follows:
WARNING SYMBOL AND SIGNAL WORD!
Type and source of danger
Results of non-compliance
X
Measures to minimise risk
Please note:
O
warning symbols draw attention to a high risk of injury.
O
The signal word indicates the severity of that risk.
Warning
symbol
ü
ü
Tab. 1.1 Meaning of the warning symbols and signal words
Figures
All measurements are provided in millimetres.
Signal word Risk
Danger Indicates an immediate, hazardous
situation which causes death or
serious injury if not respected.
Warning Indicates a potentially hazardous
situation which can cause death or
serious injury if not respected.
Caution Indicates a potentially hazardous
situation which can cause minor
injury or damage to property if not
respected.
www.bora.com
3
Page 4
EN
Safety
2 Safety
The appliance complies with the stipulated safety
requirements. The user is responsible for the safe
use of the appliance, cleaning and maintenance.
Improper use can lead to personal injury and damage
to property.
2.1 Use as intended
The appliance is solely intended for preparing food in
private households.
This appliance is not intended for:
O
outdoor use
O
heating rooms
O
cooling, ventilating or dehumidifying rooms
O
use in mobile installation sites such as motor
vehicles, ships or aeroplanes
O
use with an external timer or a separate remote
control system
O
use at altitudes of over 2,000m (metres above sea
level)
O
use when not fully installed
Any other use or any use that goes beyond that which
is described here is classed as unintended.
BORA does not assume any liability for
i
damages caused by incorrect installation,
improper use or incorrect operation.
All misuse is prohibited!
2.2 People with limited abilities
Children
The appliance can be used by children aged 8 and
over if they are supervised or have been instructed
how to use the appliance safely and understand
the resultant risks. Children must not play with the
appliance.
X
Use the childproofing feature in order to prevent
children from switching on the appliance or
changing the settings when they are unattended.
X
Supervise children in the vicinity of the appliance.
X
Do not store any items that could be of interest to
children in storage spaces above or behind the
appliance. Otherwise, they will be tempted to
climb onto the appliance.
People with reduced physical, sensory or
mental capacities
The appliance can be used by people with reduced
physical, sensory or mental capacities or a lack of
experience and/or knowledge if they are supervised
or have been instructed how to use the appliance
safely and understand the resultant risks.
Operation can be restricted using the childproofing
feature.
DANGER!
Risk of burns from hot cookware and food
Handles projecting over the edge of the worktop
are asking to be grabbed.
X
Keep children away from hot cooking zones or
ensure they are supervised at all times.
X
Do not turn pot and pan handles so they stick
out beyond the worktop.
X
Make sure that hot pots and pans cannot be
pulled down.
X
If necessary, use suitable stove guards or
covers.
X
Only use stove guards and covers that are
approved by the appliance manufacturer;
otherwise, there is a risk of accidents.
X
To choose a suitable stove guard, contact your
specialist supplier or the BORA Service Team.
2.3 General safety instructions
DANGER!
Packaging components are a choking hazard
Packaging components (e.g. lm, polystyrene) can
be life-threatening for children.
X
Store all packaging components out of reach of
children.
X
Dispose of the packaging properly and
immediately.
Any work involving cleaning and maintenance
i
must not be carried out by children unless they
are supervised at all times while doing so.
4
www.bora.com
Page 5
Safety
EN
DANGER!
Risk of electric shock or injury from damaged
surfaces
The underlying electronics can be exposed or
damaged due to ssures, fractures or cracks
in appliance surfaces (e.g. damaged glass),
particularly in the vicinity of the operating unit.
This can cause an electric shock. Furthermore, a
damaged surface can cause injuries.
X
Do not touch the damaged surface.
X
If there are any cracks, fissures or fractures,
switch the appliance off immediately.
X
Safely disconnect the appliance from the mains
using the LS switch, fuses, automatic circuit
breakers or contactor.
X
Contact BORA Service.
WARNING!
Risk of injury or damage due to incorrect
components or unauthorised modifications
Incorrect components can lead to personal
injury or damage to the appliance. Modications,
additions or alterations to the appliance can lead to
safety risks.
X
Only use original components.
X
Do not make any modifications, additions or
alterations to the appliance.
CAUTION!
Risk of injury from heavy lifting
If not handled correctly, carrying and installing
appliances can cause injury to the limbs or torso.
X
If necessary, carry and install the appliance with
another person.
X
Use appropriate aids to prevent damage or
injury.
CAUTION!
Damage from improper use
The appliance surfaces must not be used as
work or storage surfaces. This can damage the
appliances (particularly in the case of hard and
sharp objects). Never use the appliances as work
or storage surfaces.
X
Keep hard or sharp objects away from the
appliance surfaces.
Faults and errors
X
In the case of faults and errorsin the
“Troubleshooting” chapter.
X
In the event of any faults or errors that are not
mentioned, switch the appliance off and contact
BORA Service.
Pets
X
Keep pets away from the appliance.
WARNING!
Risk of injury due to mechanical damage on
the appliance
Mechanical damage (e.g. cracks, deformation,
separation of adhesive seals, etc.) to the appliance,
as well as to cables and accessories can cause
injuries.
X
Do not operate the appliance.
X
Try not to repair or replace damaged
components yourself.
X
Contact BORA Service.
CAUTION!
Appliance components can cause injury if
dropped
Appliance components (e.g. pan supports,
operating controls, covers, grease lters, etc.) can
cause injury if dropped.
X
Place any appliance components that have been
removed in a safe place near the appliances.
X
Ensure that no components removed from the
appliances can fall on the floor.
2.4 Safety instructions for
installation
The appliance must only be installed and
i
assembled by trained specialists who are
familiar with and comply with the standard
national regulations and supplementary
regulations of the local utility companies.
During installation maintain the minimum
i
clearance stated in the “Installation” (“Safety
clearances”) chapter.
Work on electrical components must only be
i
conducted by trained electrical personnel.
The appliance may only be installed with the
i
power disconnected.
The electrical safety of the appliance is only
guaranteed if it is connected to a protective
conductor system that has been installed in line with
regulations. Ensure that this basic safety precaution
is met.
www.bora.com
5
Page 6
EN
Safety
The appliance must be suitable for the regional
voltage and frequency.
X
Check the information on the identification plate
and in the event of deviations, do not connect the
appliance.
X
Do not connect the appliance to the mains until
the duct system has been installed or the
recirculation filter has been fitted.
X
Only use the connection cables supplied. Where
necessary these are included in the scope of
delivery.
X
Do not use the appliance until installation is
complete. This is the only way to ensure safe
operation.
X
Conduct all work extremely attentively and
conscientiously and in accordance with these
instructions.
X
Before handing the appliance or system over to
the end user, ensure that it has been correctly
installed.
DANGER!
Risk of electric shock from damaged appliance
A damaged appliance can cause an electric shock.
X
Check the appliance for visible damage prior to
installation.
X
Do not install or connect any damaged
appliances.
X
Do not operate any damaged appliances.
2.4.1 Safety instructions – cooktop
extractor installation
DANGER!
Risk of electric shock from incorrect stripping
of cables
Incorrect stripping of the connection cable to
external switching devices results in a risk of
electric shock.
X
Ensure that the stated stripping lengths are
adhered to.
WARNING!
Risk of injury due to moving fan wheel
There is a risk of injury while the fan is turning.
X
Only install the device with the power
disconnected.
X
Connect both sides of the fan to the duct
system before commissioning.
Special safety instructions for the planning of
extractor systems
DANGER!
Risk of smoke inhalation
When the cooktop extractor is used in exhaust
air mode, it draws in air from the room it is
installed in and from neighbouring rooms. If there
is insucient air supply, low pressure will occur.
When used at the same time as a replace that
is dependent on the air in the room, noxious
gases can be sucked into the living areas from the
chimney or outlet shaft.
X
Make sure that there is always a sufficient air
supply.
X
Only use reliable, tried-and-tested switching
devices, (e.g. window contact switch, low
pressure warning device) and have them
approved by a qualified expert (certified chimney
sweep).
Ducting connected to wall sleeves
In the case of straight ducting and a distance
<900mm between the fan and wall sleeve, a
safety guard must be provided for (available as an
accessory).
2.4.2 Safety instructions for cooktop
installation
DANGER!
Risk of electric shock from incorrect mains
connection
Connecting the appliance to the mains incorrectly
poses a risk of electric shock.
X
Make sure that the appliance has a fixed
connection to the mains voltage.
X
Make sure that the appliance is connected to a
properly installed protective conductor system.
X
Make sure that technical equipment is provided
to enable all of the appliance’s poles to be
disconnected from the mains with a contact
opening width of at least 3mm (LS switch and
automatic circuit breakers, fuses, contactor).
6
www.bora.com
Page 7
Safety
EN
DANGER!
Risk of electric shock from damaged power
supply cable
If the power supply cable is damaged (e.g. during
installation or by coming into contact with hot
cooking surfaces), this can cause an (lethal)
electric shock.
X
Make sure that the power supply cable does not
become trapped or damaged.
X
Make sure that the power supply cable does not
come into contact with hot cooking surfaces.
2.5 Safety instructions – operation
X
Do not use the appliance until installation is
complete. This is the only way to ensure safe
operation.
X
Make sure that the base of the cookware as well
as the appliance surfaces are clean and dry.
X
Always lift (do not drag) cookware to prevent
scratching and abrasion on the appliance surface.
X
Do not use the appliance as a storage surface.
X
Switch off the appliance after use.
WARNING!
Risk of burning from hot appliances
Certain appliances and their exposed parts become
hot during use. They should be left to cool down
completely after switching off. Touching hot
surfaces can cause serious burns.
X
Do not touch hot appliances.
X
Pay attention to the residual heat indicator.
WARNING!
Risk of burns due to power cut
During or after a power cut a cooktop that was
previously in operation may still be hot.
X
Do not touch the appliance while it is still hot.
X
Keep children away from the hot appliance.
DANGER!
Risk of fire from overheated oil or fat
Oil or fat in the pot can quickly heat up and ignite.
X
Never leave the appliance unattended when
cooking with oil or fat
X
Never extinguish oil and fat fires with water.
X
Switch off the appliance.
X
Extinguish the fire using a pan lid or a fire
blanket, for example.
WARNING!
Risk of burning and fire from hot objects
The appliance and its exposed parts are hot
during operation and the cooling phase. Objects
in contact with hot appliance components heat
up very quickly and can cause severe burns (this
particularly applies to metal objects such as knives,
forks, spoons, lids or appliance components) or
catch re.
X
Do not place any items on the appliance.
X
Please use suitable accessories (pot holders,
oven gloves).
CAUTION!
Damage caused by hot cookware
Hot cookware can damage certain components in
the appliance.
X
Do not put hot cookware down in the area of the
operating panel.
X
Keep hot cookware away from the air inlet
nozzle.
2.5.1 Safety instructions – cooktop
extractor operation
WARNING!
Fire risk from flambéing
While the cooktop extractor is working, it sucks up
grease from cooking. Flambéing food can cause
the grease to catch re.
X
Clean the cooktop extractor regularly.
X
Never work with a naked flame while the
cooktop extractor is running.
CAUTION!
Damage caused by objects or paper suctioned
in
Small and light items, such as cleaning cloths made
from material or paper, can be suctioned into the
cooktop extractor. This can damage the fan or
impair the exhaust performance.
X
Do not store any items or paper on the cooktop
extractor.
X
Only operate the integrated cooktop extractor
with the grease filter fitted.
CAUTION!
Damage caused by grease and dirt deposits
Grease and dirt deposits can prevent the cooktop
extractor from functioning properly.
X
Never use the cooktop extractor without a
correctly fitted stainless steel grease filter.
www.bora.com
7
Page 8
EN
Safety
Special safety instructions for using the
exhaust air mode
DANGER!
Risk of smoke inhalation
When the cooktop extractor is used in exhaust
air mode, it draws in air from the room it is
installed in and from neighbouring rooms. If there
is insucient air supply, low pressure will occur.
When used at the same time as a replace that
is dependent on the air in the room, noxious
gases can be sucked into the living areas from the
chimney or outlet shaft.
X
Make sure that there is always a sufficient air
supply.
X
Only use reliable, tried-and-tested switching
devices, (e.g. window contact switch, low
pressure warning device) and have them
approved by a qualified expert (certified chimney
sweep).
Special safety instructions for using the
recirculation mode
When cooking, additional moisture is released into
the ambient air. In recirculation mode, only a slight
amount of moisture is removed from the cooking
vapour.
X
When using the recirculation mode, ensure a
sufficient supply of fresh air, e.g. by opening a
window.
X
Ensure a normal and comfortable room climate
(humidity of 45 – 60%), e.g. by opening natural
ventilation openings or using domestic ventilation
systems.
X
After every use in recirculation mode, switch the
cooktop extractor to a low power level for about
20 minutes or activate the automatic after-run
function.
2.5.2 Safety instructions – cooktop
operation
X
Do not simply rely on the pan size recognition
function on induction cooktops; always switch the
appliance off after use.
DANGER!
Danger of fire caused by leaving the cooktop
unattended
Oil or fat in the pot can quickly heat up and ignite.
X
Never leave oil or fat to heat up unattended.
X
Never extinguish oil and fat fires with water.
X
Switch off the cooktop.
X
Extinguish the fire using a pan lid or a fire
blanket, for example.
DANGER!
Danger of explosion caused by flammable
liquids
Flammable liquids in the vicinity of a cooktop can
explode and cause serious injury.
X
Do not spray aerosols near the appliance when
it is in use.
X
Do not place any flammable liquids in the
vicinity of a cooktop.
WARNING!
Risk of burns from hot liquids boiling over
Unattended pans can boil over allowing hot liquids
to escape.
X
Keep an eye on pans when cooking.
X
Try not to let them boil over.
WARNING!
Risk of burns from hot steam
Liquid between the cooking zone and the pan base
can evaporate and cause burns.
X
Make sure that the cooking zone and the pan
base are always dry.
CAUTION!
Damage caused by sugary and salty foods
Sugary and salty foods and juices can damage the
hot cooking zone.
X
Make sure sugary and salty foods or juices do
not get onto the cooking zone while it is hot.
X
Remove sugary and salty foods and juices from
the hot cooking zone immediately.
Special safety instructions for the operation of
induction cooktops
Effect on pace makers, hearing aids and metal
implants:
induction cooktops generate a high-frequency
electromagnetic field in the area of the cooking
zones. The cooking zones may affect pacemakers,
hearing aids or metal implants negatively or disturb
8
www.bora.com
Page 9
Safety
EN
their function when in close proximity. A reduced
function of the pacemaker is unlikely.
X
If in doubt, contact the manufacturer of your
medical device, or your doctor.
2.6 Safety instructions – cleaning
and maintenance
The appliance must be cleaned at regular intervals.
Dirt can lead to damage, restriction of functions, or
bothersome odours. In the worst case scenario, this
can become a hazard.
X
Remove dirt immediately.
X
When cleaning, only use non-abrasive detergents
to prevent scratching and abrasion on the surface.
X
When cleaning, ensure that no water penetrates
the appliance. Use only a slightly damp cloth.
Never spray the device with water. Water
penetration can cause damage!
X
Do not use a steam cleaner for cleaning. Steam
can cause a short circuit on live parts and thus
lead to property damage.
X
Please follow all instructions in the “Cleaning and
Maintenance” chapter.
2.7 Safety instructions – repairs,
servicing and spare parts
The appliance must only be repaired and
i
serviced by trained specialists who are familiar
with and comply with the standard national
regulations and supplementary regulations of
the local utility companies.
Work on electrical components must only be
i
conducted by trained electrical personnel.
X
Before any repair work, safely disconnect the
appliance from the mains supply.
WARNING!
Risk of injury or damage from improper repairs
Incorrect components can lead to personal
injury or damage to the appliance. Modications,
additions or alterations to the appliance can lead to
safety risks.
X
Only use original spare parts for repairs.
X
Do not make any modifications, additions or
alterations to the appliance.
Special safety instructions for cooktop
extractor cleaning and maintenance
X
Keep the ventilation openings in the unit below
open and clean.
WARNING!
Risk of fire from fat deposits
The risk of re can be increased by failure to clean
the grease lter properly and on a regular basis, or
if the lter change is overdue.
X
Clean and replace the filter at regular intervals.
WARNING!
Risk of injury when opening the bottom
housing cover
There is a risk of injury while the fan is turning.
X
Switch off the appliance and disconnect it from
the mains before removing covers in the vicinity
of the fan.
Special safety instructions for cooktop cleaning
and maintenance
X
Whenever possible, clean the cooktops after every
use.
X
Only clean the cooktops when they have cooled
down.
A damaged power supply cable must be
i
replaced by a suitable power supply cable. This
may only be done by an authorised member of
the After Sales Service team.
2.8 Safety instructions –
disassembly and disposal
The appliance must only be disassembled by
i
trained specialists who are familiar with and
comply with the standard national regulations
and supplementary regulations of the local
utility companies.
Work on electrical components must only be
i
conducted by trained electrical personnel.
X
Before disassembly, safely disconnect the
appliance from the mains supply.
www.bora.com
9
Page 10
EN
Safety
DANGER!
Risk of electric shock from incorrect
disconnection
Incorrectly disconnecting the appliance from the
mains results in a risk of electric shock.
X
Safely disconnect the appliance from the mains
using LS switches, fuses, automatic circuit
breakers or contactors.
X
Use an authorised measuring device to ensure
that there is no power to the appliance.
X
Do not touch exposed contacts on the electronic
unit as they may contain residual charge.
10
www.bora.com
Page 11
3 Technical data
Technical data
EN
Parameter Value
Multiphase supply voltage 380–415 V 2N/3N
Single-phase supply voltage 220–240 V
Frequency 50 Hz
Maximum power consumption 7600 W (4400 W)
Fuse protection/three-phase power supply
Fuse protection/two-phase power supply
Fuse protection/single-phase power supply
Dimensions (width x depth x height) 760 x 515 x 198 mm
Weight (incl. accessories/packaging) approx. 25 kg
Cooktop
Surface material glass ceramic
Front cooking zone power levels 1–9, power setting
Rear cooking zone power levels 1–9
Size of front cooking zone Ø 210 mm
Size of rear cooking zone Ø 175 mm
Front cooking zone
power setting output
Rear cooking zone output 1400 W
Cooktop power consumption
(calculated with standard pot sizes)
Cooking zone 1 front left (210 mm) 171.3 Wh/kg
Cooking zone 2 rear left (180 mm) 168.6 Wh/kg
Cooking zone 3 front right (210 mm) 171.1 Wh/kg
Cooking zone 4 rear right (150 mm) 185.8 Wh/kg
Total (average) 174.2 Wh/kg
Recirculation system
Power levels 1–2, power setting
Size of exhaust opening 650 x 90 mm
Recirculation filter
Maximum filter service life 150 h (1 year)
Tab. 3.1 Technical data
3 x 16 A
2 x 16 A
1 x 32 A
(1 x 20 A in appliance
power management menu)
2300 W
3000 W
Device dimensions GP4U
760
Ø220
Ø175 Ø210
Fig. 3.1 GP4U device dimensions top view
727
Fig. 3.2 GP4U device dimensions front view
484
R3
275
515
15,5
5
56
www.bora.com
198
152
25–45
490–510
Fig. 3.3 GP4U device dimensions side view
196
11
Page 12
EN
v
Appliance description
4 Appliance description
Observe all safety and warning information during operation
(see „2 Safety“).
4.1 System description
4.1.1 Structure
1
2
3
4
8
5
67
Fig. 4.1 Cooktop
8
8
9 8
Fig. 4.2 Operating panel
Sensor buttons:
[1] Reduce fan power level
[2] Increase fan power level
[3] Increase power level
[3] Increase timer value
[4] Switch cooktop on/off
[5] Reduce power level
[5] Decrease timer value
[6] Select cooking zone
7
1
2
8
10
8
8
46 3
5
[1] Air inlet nozzle
[2] Stainless steel grease filter
[3] Cooktop
[4] Inlet opening
[5] Telescopic pull-out
[6] Activated charcoal filter housing
[7] Air guiding housing
[8] Operating panel
4.1.2 Operating panel and operating principle
The cooktop extractor and cooktops are operated via a central
operating panel. The operating panel is fitted with electronic
sensor buttons and display panels. The sensor buttons respond
to finger contact (touch zones). Keep your finger pressed on
the sensor button until you either hear an acoustic signal or the
display changes accordingly.
Display fields:
[7] Fan level indicator/filter service display
[8] Cooking zone indicator lamp
[9] Cooking zone indicator
[10] Timer
Display field Display Meaning
Fan level indicator
Cooking zone
indicator
Cooking zone
indicator light
Timer display (1*)
Tab. 4.1 Meaning of the displays
0
1
or
P
n
1
...
P
H
L
on
flashing
off Timer off
01
00
Fan off
Setting
2
Power setting
Automatic after-run
Power level
9
Power setting
Residual heat indicator: Cooking
zone is switched off but still hot
(temperature >60°C)
Childproofing feature active
Pan size recognition
Automatic cut-off (timer) activated
Timer on (
Set minutes for short time
...
99
(egg timer) or automatic cut-off
Timer on; no time set
00
); no time set
12
www.bora.com
Page 13
Appliance description
EN
(1*) Timer display
The timer display uses the cooking zone indicators for the two
30
rear cooking zones (e.g.
for 30 minutes). The cooking zone
indicators for the two front cooking zones are disabled while the
timer is displayed.
4.1.3 Functions
Cooktop:
O
9 power levels
O
Power setting
O
Timer functions
O
Pan size recognition
Cooktop extractor:
O
2 power levels
O
Power setting
O
Automatic after-run
O
Filter service display
Safety devices
O
Childproofing feature
O
Residual heat indicator
O
Safety shut-down
You fill find instructions on how to use/set the individual
i
functions in the “Functions and operation” chapter.
4.2 How the cooktop extractor
works – recirculation
Recirculation mode
Noises
The following noises may occur in the cookware when using
induction cooking zones, depending on the material and the
finish of the base:
O
Humming may occur when using a high power level. It
decreases or disappears if the power level is decreased.
O
Crackling or whistling may occur due to the bases of cookware
being made of different materials (e.g. sandwich base).
O
Clicking sounds may occur during electronic switching
procedures, especially at low power levels.
O
Whirring may occur when the cooling fan is switched on. In
order to increase the service life of the electronic system,
the cooktop is equipped with a cooling fan. The cooling fan
switches on automatically if the cooktop is used intensively.
You will hear a whirring sound. The cooling fan may continue
to run after the appliance has been switched off.
4.3.1 Suitable cookware
X
Observe the minimum pot base diameter.
Appliance Cooking zone Minimum cookware base diameter
GP4U front
rear
Tab. 4.2 Minimum cookware diameter
The heating and heat-through time for the base of the
i
cookware as well as the cooking results are significantly
influenced by the structure and material of the cookware.
Cookware with this symbol is suitable for induction
cooktops. The cookware used for the induction cooktop
must be made of metal, feature magnetic properties and
possess an ample base.
120mm
90 mm
The air suctioned away is purified by the grease filter and an
activated charcoal filter and fed back into the room in which the
appliance is installed.
To prevent odours in recirculation mode, an odour filter must be
used. For health and hygiene reasons, the activated charcoal
filter must be replaced at the recommended intervals
(see „7 Cleaning and maintenance“).
In recirculation mode, ensure sufficient ventilation and
i
aeration to expel humidity.
4.3 How the induction cooking zone
works
An induction coil is located underneath an induction cooking
zone. If the cooking zone is switched on, this coil creates a
magnetic field that acts directly on the base of the pot thus
heating it up. The cooking zone is only indirectly heated up by
the heat emitted by the pot. Cooking zones with induction only
work if the cookware has a magnetisable base.
Induction automatically takes into account the size of the
cookware used which means that only the area in the cooking
zone covered by the base of the pot is heated up.
Suitable cookware is made of:
O
stainless steel with a magnetisable base
O
enamelled steel
O
cast iron
X
Perform a magnet test, if necessary. If a magnet sticks to the
base of the utensils, they are normally induction compatible.
X
Pay attention to the cookware base. The base of the cookware
should not show any sign of curvature. Due to incorrect hob
temperature monitoring, this curvature may cause the cookware
to overheat. To avoid scratching the cooktop, the base of the
cookware must not have any sharp grooves or sharp edges.
X
Place the cookware (without a mat or similar) directly onto the
glass ceramic.
www.bora.com
13
Page 14
EN
Installation
5 Installation
X
Observe all safety and warning information
(see „2 Safety“).
The mains supply cable for single-phase and two-phase
i
connections is to be provided at the installation site.
The power supply cable must be provided by the customer.
i
The appliance must not be installed above cooling devices,
i
dishwashers, stoves, ovens, washing machines or dryers.
The contact surface of the worktops and wall sealing
i
strips must be made of a heat-resistant material (up to
approx. 100°C).
Worktop cut-outs must be moisture-sealed using suitable
i
means and, where necessary, fitted with a thermal
insulator.
The integrated cooktop extractor must not be used with
i
other cooktops.
To ensure that the cooktops perform optimally at all times,
i
there must be sufficient ventilation beneath the cooktops.
If cable protection (false floor) is planned beneath the
i
appliance, this must be fitted so it does not obstruct
ventilation.
5.2 Tool and aids
The following special tools are required to correctly install the
cooktop:
O
Drill or cordless drill with 14 mm wood bit
O
Compass saw or hand saw
O
Torx 20 screwdriver
O
Black, heat-resistant silicone sealant
5.3 Assembly instructions
Safety clearances
X
Maintain the following safety clearances:
3
2
1
5.1 Scope of delivery
Name Quantity
Induction cooktop with cooktop extractor 1
Air inlet nozzle 1
Stainless steel grease filter 1
BAKF activated charcoal filter 2
Telescopic pull-out 1
Installation clamps with screws 5
Sealing tape 1
Cable routing clips 3
Height adjustment plate set 1
Operating and installation instructions 1
Template for back panel cut-out 1
Power supply cable 1,5 m 1
Tab. 5.1 Scope of delivery
X
Make sure the delivery is complete and check it for damage.
X
If there are any missing or damaged parts, please notify the
BORA After Sales Service immediately.
X
Do not under any circumstances install parts which are damaged.
X
Dispose of transport packaging in the proper manner
(see „9 Decommissioning, disassembly and disposal“).
Fig. 5.1 Minimum distance
[1] Rear minimum clearance of 50mm between the worktop cut-
out and the rear edge of the worktop.
[2] Minimum clearance of 300mm from the left and right of the
worktop cut-out to the adjacent cabinet or wall.
[3] Minimum clearance of 480mm between the worktop and the
wall unit. A minimum clearance of 1000mm is recommended
for ergonomic reasons.
14
www.bora.com
Page 15
Installation
EN
GP4U minimum unit dimensions
≥600
198
Fig. 5.2 GP4U minimum unit dimensions
Return flow of recirculated air
≥800
5.4 Preparing kitchen units
GP4U installation dimensions
min. 600
min. 50
196
490 – 510
575
118
198
0 – 20
min. 25
21
Fig. 5.3 Return ow aperture in the plinth area
[1] Return flow aperture (total opening cross-section ≥500 cm²)
[2] Recirculating air
In the case of recirculation appliances there must be a return
flow aperture in the kitchen units> 500 cm
2
.
For recirculation, the necessary return flow aperture can be
created using a shortened plinth. A slatted plinth with at least
the minimum opening cross-section can also be used.
X
Decrease the height of the skirting boards or create
corresponding openings in the plinth.
Fig. 5.4 GP4U installation dimensions, 600 mm deep worktop
General kitchen unit specifications
O
Cross bars on the kitchen unit in the area of the worktop cutout may need to be removed.
O
In the case of thin worktops, there must be a sufficiently rigid
support plate on the unit.
O
No false floor is necessary below the cooktop. If cable
protection (false floor) is planned, the following must be taken
into account:
O
It must be fitted in such a way that it can be removed for
maintenance work.
O
To ensure sufficient cooktop ventilation, a minimum
distance of 15 mm to the bottom edge of the cooktop is
to be observed.
O
The drawers and/or shelves in the floor unit must be
removable.
O
For correct installation, the slide-in units of the base cabinet
must be shortened depending on the installation situation.
Adjusting the rear wall of the unit
O
The floor unit must have a continuous rear wall so that the
recirculated air is not directed into the front furniture body
compartment.
O
There must be a cut-out in the rear wall.
O
A minimum clearance of 25 mm between the rear furniture
body wall and an adjacent kitchen unit or room wall must be
observed for the return flow of the recirculation air.
X
Adapt the rear wall according to the required installation
dimensions.
X
If applicable, move the rear wall.
X
If necessary extend the height of the rear wall so that the unit
is closed to the front.
www.bora.com
15
Page 16
EN
GP4UBP-100
Installation
Creating a cut-out in the rear wall
90
650
118
Cut-out dimensions for flush installation
764 ±2
735 ±2
(≥ 50)
≤ R5
≥ 50
Fig. 5.7 Cut-out dimensions for ush installation
14,5
6,5 +0,5
≤ R5
490 ±2
≥ 600
519 ±2
Fig. 5.5 Rear wall cut-out
GP4U
Schablone für Rückwandausschnitt
Template for cut-out on rear wall
0
10
20
30
40
R5
90
650
0
0
10
10
20
20
30
30
40
40
0
10
20
30
40
Fig. 5.6 Template for back panel cut-out
X
Draw the return flow aperture central to the cooktop with the
aid of the template provided.
Flush and surface mounting options must be taken into
i
account when positioning the template.
X
Cut out the back panel cut-out with a saw.
X
A cable opening with a 14 mm diameter will need to be
provided either to the left or right of the rear wall cut-out.
5.5 Creating the worktop cut-out
The minimum distance of 50 mm from the front edge of
i
the worktop to the worktop cut-out is a recommendation
from BORA.
10 - 40
Fig. 5.8 Rebate dimensions for ush installation
Cut-out dimensions for surface mounting
118
≤ R5
735 ±2
Fig. 5.9 Cut-out dimensions for surface mounting
12,5
(≥ 50)
≥ 50
490 ±2
≥ 600
X
Comply with the instructions of the worktop manufacturer.
X
Create the worktop cut-out taking into account the specified
cut-out dimensions.
X
Make sure that the cut surfaces of the worktops are properly
sealed.
16
10 - 40
Fig. 5.10 Overlay dimensions for surface mounting
www.bora.com
Page 17
5.6 Installing the appliance
Attaching the sealing tape
1
2
Installation
EN
Fig. 5.11 Sealing tape for surface mounting
1
2
Fig. 5.12 Sealing tape, ush installation
[1] Black, heat-resistant silicone sealant
[2] Sealing tape
X
If surface mounting, attach the enclosed sealing tape [2] to
the underside of the cooktop before installing it. Do not leave
any gaps.
X
In the case of flush installation, attach the enclosed sealing
tape [2] to the horizontal cutting edge in the worktop cut-out,
even if you are sealing the cooktop with a silicone sealing
compound[1] or similar.
Attaching the telescopic pull-out to the appliance
1
3
2
4
Fig. 5.14 Mounting the frame of the exible duct
[1] Position shackles
[2] Retaining groove on the activated charcoal filter housing
[3] Flexible duct frame
[4] Lower lock
X
Hang the frame of the telescopic pull-out in the retaining
groove [2] on the activated charcoal filter housing.
X
Ensure that both lateral position shackles [1] are in the guide.
X
Slide the frame upwards [3] until the lower [4] and upper lock
engage in the middle.
X
Ensure that the frame is inserted into the activated charcoal
filter housing groove all the way round.
X
Remove the protective film from the adhesive tape on the
front of the telescopic pull-out.
Inserting the activated charcoal filter
12 31
Fig. 5.13 Opening the housing cover
[1] Outer locks
[2] Central lock
[3] Activated charcoal filter housing cover
X
Open the cover [3] of the activated charcoal filter housing from
underneath by releasing the two outer locks [1] and the central
lock [2].
www.bora.com
1
2
Fig. 5.15 Inserting the activated charcoal lter
[1] Activated charcoal filter housing cover
[2] Activated charcoal filter
X
Remove the packaging from the activated charcoal filters.
X
Insert the two activated charcoal filters [2] from below.
X
Check the direction of flow of the filters. This is identified by
an arrow.
X
Close and lock the activated charcoal filter housing cover [1].
17
Page 18
EN
1
Installation
Inserting the cooktop
54321
1 2
Fig. 5.18 Height adjustment plates
[1] Sealing tape
[2] Optional height adjustment plates
X
If necessary, lay the height adjustment plates [2] underneath.
X
Place the height adjustment plates next to the sealing tape [2].
Securing the cooktop
Fig. 5.16 Inserting the cooktop
[1] Cooktop
[2] Suction opening
[3] Air inlet nozzle
[4] Stainless steel grease filter
[5] Worktop cut-out
X
Before inserting the cooktop, remove the air inlet nozzle [3]
and the stainless steel grease filter [4].
X
Use the suction opening [2] as a handle during insertion.
X
Incline the cooktop [1] as you lift it into the worktop cut-out [5]
X
Insert the cooktop [1] into the centre of the worktop cut-out [5].
X
Precisely align the cooktop.
Information regarding flush installation:
X
Make sure that the sealing tape of the cooktop is well sealed
all the way round.
Information regarding surface mounting:
X
Make sure that the sealing tape for the cooktop is flat against
the worktop.
Height adjustment plates for flush installation (optional)
321
16
4
5
Fig. 5.19 Securing the cooktop in the middle
[1] Cooktop
[2] Air inlet nozzle
[3] Stainless steel grease filter
[4] Worktop cut-out
[5] Installation clamp with screw
[6] Worktop
2
X
Fasten the cooktop [1] to the worktop [6] using the
5 mounting brackets [5].
O
Fig. 5.17 Height adjustment plates
[1] Cooktop
[2] Height adjustment plate
18
2 on each side, 1 in the centre at the front
O
Tightening torque: max. 2 Nm
X
Insert the stainless steel grease filter [3] and the air inlet
nozzle [2].
www.bora.com
Page 19
Establishing a connection with the back wall
Installation
EN
1
2
3
4
Fig. 5.20 Connection with the back wall
[1] Telescopic pull-out
[2] Adhesive tape
[3] Rear wall cut-out
[4] Back wall of unit
X
Push the telescopic pull-out [1] until it is tight up against the
rear wall of the unit [4].
O
With the telescopic pull-out the distance to the rear wall cutout [3] can be flexibly bridged.
X
Check that the telescopic pull-out [1] is flush with the rear wall
of the unit [4] and closes it off.
X
Ensure that the telescopic pull-out [1] is firmly attached to the
rear wall of the unit [4].
5.7 Establishing the power
connection
1
Fig. 5.21 Connection diagram 3-phase connection
1
Fig. 5.22 Connection diagram 2-phase connection
1
2 3 4
L1 L2
L3
220 - 240 V~
220 - 240 V~
2 3 4
L1 L2
220 - 240 V~
220 - 240 V~
2 3 4
L1
220 - 240 V~
N
220 - 240 V~
N
N
PE
PE
PE
X
Observe all national and regional laws and regulations as
well as the supplementary regulations of the local utility
companies.
The power connection may only be established by certified
i
specialists. The specialist also assumes responsibility for
the proper installation and commissioning.
Connections via plug-in contacts (Schuko plugs) are not
i
permitted.
The mains supply cable provided in the scope of delivery
i
is only suitable for a 3-phase connection.
X
Switch off the main switch/automatic circuit breaker before
connecting the cooktop.
X
Secure the main switch/automatic circuit breaker against
being switched back on without permission.
X
Make sure the power to the appliance is disconnected.
X
Connect the cooktop exclusively via a fixed connection to an
H 05 VV-F power supply cable with corresponding minimum
cross-section.
Connection Fuse protection Minimum cross-
section
3-phase connection 3 x 16 A 2.5 mm
2-phase connection 2 x 16 A 2.5 mm
1-phase connection 1 x 32 A 4 mm
Tab. 5.2 Fuse protection and minimum cross-section
2
2
2
Fig. 5.23 Connection diagram 1-phase connection
1
2
3
3
1
Fig. 5.24 Electrical connections of the cooktop
[1] Bore holes
[2] Power supply
[3] Cable mounting clip
X
Connect the power supply cable to the power supply [2] of the
cooktop with integrated cooktop extractor in accordance with
the relevant connection diagram (see fig. “Connection diagram”).
X
For a one-phase or two-phase connection, connect the relevant
contacts using the BKAS connector clip (included in delivery).
www.bora.com
19
Page 20
EN
Installation
X
Fasten the cable mounting clips [3] to the designated bore
holes [1] either on the left or right hand side for the cable
routing to the cable opening in the rear wall of the unit.
X
Ensure that the cable is not trapped or damaged and is not
able to come into contact with any hot hobs.
X
Check that installation has been carried out correctly.
X
Switch on the main switch/automatic circuit breaker.
X
Put the cooktop into operation (see „6 Functions and
operation“).
X
Check that all the functions are working correctly.
Appliance power management
(total power reduction)
The total appliance power can be reduced to 4400 W upon
initial commissioning if the required electrical power cannot be
provided at the installation site. The connection must always be
equipped with 20 A fuse protection as a minimum.
Programming the appliance power management
The appliance must be switched off for programming and the
childproofing feature must not be activated. Programme the
cooktop within 2 minutes of the cooktop being connected to the
power supply.
X
To programme, press all 4 cooking zone selection buttons
simultaneously for 3 seconds.
O
7.4 (factory setting) will appear in the display.
X
Press the or the button to reduce the total power
consumption to 4.4.
X
To save, press all 4 cooking zone selection buttons
simultaneously for 3 seconds until a beep is heard.
O
The beep signals that the settings have been saved and the
cooktop will switch itself off.
The next time it is switched on, the cooktop will be ready for use.
5.7.1 Function test
5.8 Sealing the appliance
1
Fig. 5.25 Silicone sealant in surface mounting
[1] Black, heat-resistant silicone sealant
1
Fig. 5.26 Silicone sealant in ush installation
[1] Black, heat-resistant silicone sealant
X
Once all of the installation work is complete, seal the
appliance with black, heat-resistant silicone sealant [1].
X
Make sure that no silicone sealant gets under the cooktop.
5.9 Handover to user
Once installation is complete:
X
Explain the main functions to the user.
X
Explain all safety-related aspects of operation and handling
to the user.
X
Provide the user with the accessories and operating and
installation instructions, which are to be kept in a safe place.
X
Carry out a thorough function test on the appliance.
X
In the event of error messages, see „8 Troubleshooting“.
20
www.bora.com
Page 21
6 Functions and operation
ßp
Functions and operation
EN
X
Observe all safety and warning information during operation
(see „2 Safety“).
Do not operate the integrated cooktop extractor with
i
other cooktops.
The cooktop should only be operated when the activated
i
charcoal filter, the stainless steel grease filter and the air
inlet nozzle are installed.
6.1 Cooktop
6.1.1 Switching the cooktop on/off
Switching the cooktop on
X
Press to switch on the cooktop. The power level 0 is
shown by the cooking zone indicators.
Switching the cooktop off
X
Press to switch off the cooktop.
X
Pay attention to the residual heat indicator
(see „4 Appliance description“).
6.1.2 Switching the cooking zone on/off
Activity Power level
Melting butter and chocolate, breaking up gelatine
Keeping sauces and soups warm, soaking rice
Cooking potatoes, pasta, soups and ragouts, steaming
fruit, vegetables and fish, defrosting food
Frying in coated pans, moderate frying (without
overheating the fat) of pork cutlets or fish
Heating up fat, browning fish, cooking thickened
sauces and soups, making omelettes
Bringing large amounts of liquid to the boil, searing steaks
Heating up water
Tab. 6.3 Recommendations for power levels
The specifications provided in the table are standard values.
Depending on the cookware and filling quantity, it is
recommended to either decrease or increase the power level.
Adjusting the power level
X
Press to set power level 5, or press , to set power level 9.
Changing the power level
X
Press the cooking zone button (e.g. ) for the desired
cooking zone. The cooking zone indicator lights up more
brightly.
X
Press or until the cooking zone indicator shows the
required power level.
–
–
–
–
Switching on the cooking zone
X
Press the cooking zone button (e.g. ) for the desired
cooking zone. The
more brightly. The cooking zone indicator light illuminates.
Switching off the cooking zone
Use the operating panel to switch off the cooking zone
i
after use. Do not rely on the pan size recognition.
X
Press the cooking zone button (e.g. ) for the desired
cooking zone.
X
Continue pressing or , until the cooking zone indicator
displays power level
seconds.
0
in the cooking zone indicator lights up
0
. The display will show a 0 for a few
6.1.3 Power levels
The high power output of induction cooktops results in the very
quick heating up of cookware. In order to avoid burning food,
slight adjustment is needed in comparison to conventional
cooking systems when selecting the power level.
6.1.4 Power setting
The two front cooking zones are equipped with a powerenhancing power setting.
The power setting can be used in order to quickly heat up large
quantities of water. If the power setting is activated, the cooking
zones will run at extra high power. After 5 minutes, the cooking
zone is automatically switched to power level
If a cooking zone is operated with the power setting
second cooking zone on that side can be operated on a
maximum power level of
Never heat up oil, fat and the like on this power setting.
i
The bottom of the pan can overheat due to the high
power output.
Switching on the power setting
X
Press the cooking zone button (e.g. ) for the desired
cooking zone.
X
Continue pressing until the power setting P is displayed by
the cooking zone indicator. After 5 minutes, the cooking zone
is automatically switched to power level
X
If a cooking zone is operated with the power setting P, the
second cooking zone on that side can be operated on a
maximum power level of
X
If the power level is increased to more than 5, the power
setting P is deactivated.
5
.
5
.
9
.
P
, the
9
.
www.bora.com
21
Page 22
EN
Functions and operation
Switching the power setting off early
X
Press the cooking zone button (e.g. ) for the desired
cooking zone. The indicator becomes brighter.
X
Continue pressing until the lower power level that you
require is displayed.
6.1.5 Timer functions
You can use 2 timer functions:
O
Short-time timer (egg timer) (cooking zone is not automatically
switched off)
O
Cooking zone timer (to automatically switch off a cooking zone)
You can set a time range of between 1 and 99 minutes for both
timer functions.
Prerequisite
O
The cooktop must be switched on.
When the set time has lapsed, 00 will be displayed for
i
a few seconds in the timer display. At the same time, an
alarm will be heard for a few seconds.
If you press first, 1 minute will be preset as the
i
starting time. If you press
preset as the starting time.
Switching off the timer alarm
X
Press any sensor button on the operating panel to end the
alarm prematurely.
Short-time timer (egg timer)
X
Press and simultaneously. The two rear cooking zone
indicators will display
X
Press or to set the required time.
00
Cooking zone timer
You can set a cooking zone timer for each cooking zone.
The relevant cooking zone indicator shows whether the
i
cooking zone timer is activated. The cooking zone indicator
lights up until the cooking zone has automatically switched
off after the preset time has passed.
If several cooking zones are activated with the cooking
i
zone timer, the cooking zone indicator with the lowest
timer value flashes if no cooking zone is selected.
Prerequisite
O
A cooking zone has been selected.
O
A power level has been set.
first, 30minutes will be
for a few seconds.
Changing the timer settings
X
Press the cooking zone button for the cooking zone for which
you wish to change the timer setting.
X
Press and simultaneously. The set time is shown in the
timer display and the cooking zone indicator light flashes.
X
Press or to set the required time.
If several timers are activated
X
Press and simultaneously as many times as necessary
until the indicator light for the required cooking zone flashes.
The indicator lights on the cooking zones for which a timer has
been activated are operated clockwise starting with the shorttime timer (egg timer).
X
Press or to change the required time.
Switching the timer off early
X
Press the cooking zone button on the cooking zone for which
you want to switch off the timer.
X
Press and simultaneously. The set time is shown in the
timer display and the cooking zone indicator light flashes.
X
Press until the timer display shows 00.
6.1.6 Pan size recognition
The cooking zone does not work:
O
If it is switched on without cookware or with unsuitable cookware.
O
If the base diameter of the cookware is too small.
O
If the cookware is removed from a cooking zone that is
switched on.
v
The cooking zone indicator displays
(also see “Induction
cooking zone operating principle” in the „4 Appliance
description“ chapter).
6.2 Cooktop extractor
Prerequisite:
O
The cooktop is switched on.
Recommendations for efficient vapour extraction:
X
Always use a lid on pots that are particularly high. This ensures
effective vapour extraction. It also reduces power consumption.
X
Only operate the cooktop extractor at the minimum power
level required for effective vapour extraction. This enables
you to improve the performance of the odour filters in
recirculation mode.
X
Only operate the hob at the minimum power level required
for cooking. This reduces the cooking vapours and the power
consumption.
X
Avoid strong drafts.
X
Press and simultaneously. The two rear cooking zone
indicators will display
X
Press or to set the required time.
00
for a few seconds.
After the last input, the set time will be displayed in the timer
display for a few seconds.
22
6.2.1 Switching the cooktop extractor on/off
Switching on the cooktop extractor
X
Press or to switch the cooktop extractor on. 0 is
displayed by the fan level indicator. In case of no further input,
the cooktop extractor will switch off automatically after a few
seconds.
www.bora.com
Page 23
Functions and operation
EN
Switching off the cooktop extractor
X
Press and simultaneously until 0 is displayed by the
fan level indicator.
or
X
Press or several times until 0 is displayed by the fan
level indicator.
If the fan level indicator displays 0, the cooktop extractor is
switched off automatically after a few seconds.
6.2.2 Power levels
Adjusting the power level
X
Press to increase the fan level. The fan level sequence is
as follows:
Switching on the automatic after-run function
X
Continue pressing until the fan level n for the automatic
after-run function is displayed.
6.2.5 Filter service display
The filter service display becomes active after the cooktop
extractor has been operated for 150 hours. The activated
charcoal filters are exhausted and the stainless steel grease
filter needs to be thoroughly cleaned.
O
F
is displayed in the filter service display.
O
The filter service display is shown every time the cooktop
extractor is switched on and remains active until the filter has
been changed and the filter service display has been reset.
O
The cooktop extractor can still be operated without limitations.
If you do not wish to change the filter yet because, for example,
you only cook occasionally:
X
Press or to switch to the normal operating mode. 0 is
displayed by the fan level indicator.
Changing the filter
X
Switch off the cooktop with integrated cooktop extractor.
X
Observe all the information provided in the “Cleaning” chapter.
X
Replace the activated charcoal filter.
X
Clean the stainless steel grease filter, the air inlet nozzle, the
air guiding housing and the housing base.
Fig. 6.1 Fan level sequence
X
Press to decrease the fan level. The fan level sequence is
as follows:
Fig. 6.2 Fan level sequence
6.2.3 Power setting
The cooktop extractor has a power-enhancing power setting.
This power setting makes it possible to suction away high levels
of cooking vapours more quickly.
6.2.4 Automatic after-run
The cooktop extractor continues to run on power level 1 and
switches off automatically after 20 minutes.
Resetting the filter service display
If the activated charcoal filter has been replaced and the
stainless steel grease filter has been cleaned, it will be
necessary to reset the filter service display.
X
Switch on the cooktop with integrated cooktop extractor.
X
Press and simultaneously for at least 3 seconds until
a flashing
seconds the
been reset.
0
is displayed by the fan level indicator. After a few
0
will stop flashing. The filter service display has
6.3 Safety devices
6.3.1 Childproofing feature
The childproofing feature prevents the appliance from being
switched on accidentally.
If a cooking zone indicator alternates between displaying
i
L
and H, the cooking zone is still hot.
Switching on the childproofing feature
Prerequisites:
O
The cooktop is switched on.
O
All cooking zones are switched off.
X
Press the sensor buttons and simultaneously within
10 seconds of switching on and then press sensor button
again. L is displayed by all cooking zone indicators. The
childproofing feature is activated.
www.bora.com
23
Page 24
EN
Functions and operation
Deactivating the childproofing feature for a cooking
session
If a cooking zone indicator alternates between displaying
i
0
and H, the cooking zone is still hot.
X
Press sensor buttons and simultaneously. The power
level
0
is displayed by all cooking zone indicators and the
cooking zone indicator lights flash.
The power level you require can now be set for each cooking zone.
After the cooktop has been switched off, the childproofing
feature is activated again.
Switching off the childproofing feature
If a cooking zone indicator alternates between displaying
i
0
and H, the cooking zone is still hot.
Prerequisites:
O
The cooktop is switched on.
X
Press the sensor buttons and simultaneously and then
press
level
again. All cooking zone indicators show the power
0
. The childproofing feature is deactivated.
6.3.2 Residual heat indicator
Overheating protection
If the cooktop overheats, the power is reduced or the
i
cooktop is switched off completely.
The appliance is fitted with overheating protection. The
overheating protection can be triggered if:
O
Cookware is heated up empty.
O
Oil or fat is heated on high power.
O
A hot cooking zone is switched on again after a power cut.
Whilst the overheating protection is active, one of the following
steps is taken:
O
The activated power setting is switched back to the previous level.
O
The power setting P can no longer be switched on.
O
The set power level is reduced.
O
The cooktop switches off completely.
After a sufficient cooling period, the cooktop can be used again.
Automatic switch-off if the button is pressed and held
The cooktop will be switched off automatically when one or
more sensor buttons are touched for longer than 10 seconds
(finger contact, objects, soiling).
O
After a few seconds, the cooktop will switch off.
X
Remove your finger or the object from the cooktop.
X
Clean the cooktop as required.
X
Where necessary, switch the cooktop back on
After switching it off, the cooking zone remains hot.
While H is displayed by the cooking zone indicator
i
(residual heat indicator), do not touch the cooking zone
or place any heat-sensitive objects on top of it. Risk of
burns and fire!
X
Pay attention to the residual heat indicator.
X
Be careful not to touch or place objects on hot hobs.
6.3.3 Safety shut-down
Cooking zone
Each cooking zone is switched off automatically when the
cooking zone exceeds the maximum operating duration on one
power level.
Power level 1 2 3 4 5 6 7 8 9
Switch off after x
hours
Tab. 6.4 Overview of the safety shut-down
X
Switch the cooking zone back on if you want to put the cooking
zone back into operation.
8 6 5 5 4 1.5 1.5 1.5 1.5
6.4 Saving energy
X
Follow all of the energy-saving tips to use the cooktop with
integrated cooktop extractor in an energy-efficient manner.
X
When purchasing cookware, pay attention to the diameter of
the base as the upper diameter of the pot is usually specified.
The diameter of the base is often smaller.
X
Use pressure cookers. Due to the closed cooking chamber
and the overpressure, these save a great deal of time and
energy. Shorter cooking times also help preserve vitamins.
X
Make sure there is sufficient liquid in the pressure cooker. An
empty pot which is still being heated can lead to overheating.
This can damage both the cooking zone and the pot.
X
If possible, always seal cookware using a suitable lid.
X
Choose a suitable size of cookware for the amount of food you
are cooking. A big pot that is barely filled requires a lot of energy.
Cooktop extractor
The cooktop extractor switches off automatically if no buttons
are pressed for 120 minutes.
24
www.bora.com
Page 25
7 Cleaning and maintenance
Cleaning and maintenance
EN
X
Observe all safety and warning information
(see „2 Safety“).
X
When conducting scheduled cleaning and maintenance, ensure
that the cooktop and cooktop extractor are fully switched
off and cooled so as to prevent injury (see „6 Functions and
operation“).
O
Regular cleaning and maintenance ensures long service life of
the product and optimal function.
X
Adhere to the following cleaning and maintenance cycles:
Component Cleaning cycle
Operating panel Immediately after every soiling
Cooktop Clean with conventional glass ceramic
detergents immediately after soiling and
on a weekly basis
Cooktop extractor Weekly
Air inlet nozzle and
stainless steel filter
Air guiding housing Every 6 months or when replacing the
Activated charcoal filter
(with recirculation only)
Tab. 12.1 Cleaning cycles
After cooking very greasy dishes; at least
once a week, when the fan level indicator
shows F clean by hand or in the dishwasher
(at 65°C max.); clean the stainless steel
surfaces in the polishing direction only!
activated charcoal filter
Replace if odours have built up, extraction
power is dwindling or the fan power level
indicator shows
F
7.1 Cleaning agents
7.3 Cleaning the cooktop
When the cooktop extractor is in use the air inlet nozzle
i
must be fitted so that no small or light objects such as
fabric or paper cleaning cloths can be sucked in.
X
Make sure that the cooktop is switched off.
X
Wait until all cooking zones are cold.
X
Remove all coarse dirt and food residues from the co
using a glass ceramic scraper.
X
Apply the cleaning agent to the cold cooktop.
X
Spread the cleaning agent using kitchen roll or a clean cloth.
X
Wipe the cooktop clean with a damp cloth.
X
Dry the cooktop with a clean cloth.
If the cooktop is hot:
X
Remove stubborn residues of plastic, aluminium foil, sugar or
sweet dishes from the hot cooking zone immediately using a
glass ceramic scraper to prevent burning.
Special soiling
X
Remove heavy soiling and marks (limescale marks, motherof-pearl-like shiny marks) using cleaning products while the
cooktop is still warm.
X
Wipe off any food that boils over with a damp cloth.
X
Remove any remaining dirt with the glass ceramic scraper.
X
Always remove any seeds, crumbs or similar that fall onto the
cooktop during cooking immediately to prevent the surface
getting scratched.
oktop
Due to the use of aggressive cleaning agents and
i
abrasion caused by the pot bases the surface will
become damaged and dark stains will occur.
To clean the cooktop, you need a special glass ceramic scraper
and suitable cleaning agents.
X
Never use steam cleaners, abrasive sponges, scouring pads or
chemically aggressive cleaning agents (e.g. oven cleaner spray).
X
Make sure that the cleaning agent does not contain any sand,
soda, acids, lyes or chloride.
For the air inlet nozzle and grease filter
X
Do not use any aggressive cleaning agents or agents
containing acid or lye.
7.2 Looking after the cooktop
X
Never use the cooktop as a work or storage surface.
X
Do not push or pull cookware over the cooktop.
X
Always lift pots and pans.
X
Keep the cooktop clean.
X
Remove any dirt immediately.
X
Only use cookware suitable for glass ceramic cooktops
(see „4 Appliance description“).
Any changes in colour or glossy spots do not mean that the
cooktop is damaged. They do not affect the functionality of the
cooktop or the stability of the glass ceramic panel.
Changes in the colour of the cooktop are the result of residues
which have not been removed and have burnt on.
Glossy spots are the result of wear by the pan base, especially
if aluminium-based cookware or unsuitable cleaning agents are
used. These are difficult to remove.
7.4 Cleaning the cooktop extractor
The air inlet nozzle and stainless steel grease filter absorb the
greasy particles from cooking vapours.
X
Make sure that the cooktop and cooktop extractor are
switched off.
X
Wait until the fan indicator shows 0.
X
Clean the cooktop extractor in accordance with the
cleaning cycles.
X
Clean the surfaces of the extraction system using a soft,
damp cloth, detergent or a mild window cleaning agent.
X
Soften dried on dirt using a damp cloth (do not scrape it off!).
www.bora.com
25
Page 26
EN
Cleaning and maintenance
Removing the air inlet nozzle and stainless steel
grease filter
1
2
Fig. 12.1 Removing the air inlet nozzle
[1] Air inlet nozzle
[2] Access opening
Prerequisite:
0
The fan level indicator shows
X
Reach into the access opening [2].
X
Pull the air inlet nozzle [1] up and out.
.
Fitting the stainless steel grease filter and air inlet nozzle
X
Take hold of the stainless steel grease filter by the handle [2].
X
Insert the stainless steel grease filter [1] into the suction opening.
X
Ensure that the stainless steel grease filter is lying on the bottom
of the housing base. A lock is not provided or necessary.
X
Reach into the access opening [2] of the air inlet nozzle.
X
Insert the air inlet nozzle [1] into the centre of the suction
opening.
X
Press the air inlet nozzle down until it clicks into place.
7.5 Cleaning the air guiding housing
Grease particles and limescale residues from cooking vapours
can settle on the surface of the air guiding housing. For this
reason, regular cleaning is essential.
The air guiding housing can be found on the bottom of the
cooktop inside the floor unit.
Opening the air guiding housing.
X
Make sure that the cooktop and cooktop extractor are
switched off.
X
Wait until the fan level indicator shows 0.
1
2
3
Fig. 12.2 Removing the stainless steel grease lter
[1] Stainless steel grease filter
[2] Handle
[3] Suction opening
X
Take hold of the stainless steel grease filter by the handle [2].
X
Pull the stainless steel grease filter [1] up and out of the
suction opening [3].
Cleaning the air inlet nozzle and stainless steel grease filter
Clean stainless steel surfaces in the polishing direction only.
i
If it is no longer possible to clean the stainless steel
i
grease filter completely, it must be replaced.
Manual cleaning
X
Use a cleaner and degreaser in one.
X
Rinse the air inlet nozzle and stainless steel grease filter with
hot water.
X
Use a soft brush to clean the air inlet nozzle and stainless
steel grease filter.
X
After cleaning, rinse the air inlet nozzle and stainless steel
grease filter well.
1 12 23 4
Fig. 12.3 Opening the air guiding housing.
[1] Rear locks
[2] Front locks
[3] Housing base
[4] Air guiding housing
X
Hold the housing base [3] with one hand.
X
Release both locks [1] on the back.
X
Release both locks [2] on the front.
X
Remove the housing base [3].
X
Clean the air guiding housing [4] and the housing base [3] with
a mild cleaning agent.
Cleaning in the dishwasher
X
Rinse the air inlet nozzle and stainless steel grease filter with a
rinsing program at a maximum of 65°C.
26
www.bora.com
Page 27
Closing the air guiding housing
Cleaning and maintenance
EN
1
2
3
4
5
Fig. 12.4 Closing the air guiding housing
[1] Air guiding housing
[2] Sealing groove
[3] Retainer hook
[4] Locking tab
[5] Housing base
X
Using both hands, position the housing base [5] in such a way
that the locking tabs [4] on the housing base line up with the
retainer hooks [3] on the housing.
X
Insert the housing base into the sealing groove [2] of the air
guiding housing [1].
X
Push the housing base [5] upwards until the 4 locking tabs (2
front, 2 rear) click into place on the retainer hooks [3].
X
Check that all 4 locking tabs [4] have clicked into place correctly.
7.6 Changing the activated charcoal
filter
Two activated charcoal filters will only be fitted with the stainless
steel grease filter if the cooktop extractor is used in recirculation
mode. The activated charcoal filters absorb cooking odours that
arise during cooking.
1
2 13
Fig. 12.5 Unlocking the activated charcoal lter housing cover
[1] Outer locks
[2] Central lock
[3] Activated charcoal filter housing cover
Removing the activated charcoal filter
1
Fig. 12.6 Releasing the outer locks
[1] Outer lock
X
Release both outer locks [1].
1
The activated charcoal filters must be replaced when
i
the fan indicator shows
F
(filter service display). You
can obtain the activated charcoal filter BAKF from your
specialist supplier or by contacting BORA via the website
at www.bora.com.
X
Make sure that the cooktop and cooktop extractor are
switched off.
X
Wait until the fan power level indicator shows 0.
www.bora.com
Fig. 12.7 Opening the central locks
[1] Central lock
X
Release the lock [1] in the centre.
X
Fold the housing cover down until it clicks into place.
27
Page 28
EN
Cleaning and maintenance
click
click
click
1 2
Fig. 12.8 Removing the activated charcoal lter
[1] Filter bracket
[2] Activated charcoal filter
X
Hold the activated charcoal filter [2] with one hand.
X
Push the filter bracket [1] towards the back.
X
Pull the activated charcoal filter down and out.
X
Dispose of the used activated charcoal filter in the household
waste.
Inserting the activated charcoal filter
1 3 12
Fig. 12.10 Closing the activated charcoal lter housing cover
[1] Outer locks
[2] Activated charcoal filter housing cover
[3] Central lock
X
Fold the activated charcoal filter housing cover [2] upwards.
X
Press the centre of the activated charcoal filter housing cover
until the central lock [3] clicks into place.
X
Press the sides of the activated charcoal filter housing cover
and close the outer locks [1] until they click into place.
Resetting the filter service display
X
Reset the filter service display (see „6 Functions and
operation“).
1 2
Fig. 12.9 Inserting the activated charcoal lter
[1] Activated charcoal filter
[2] Filter bracket
X
Position the new activated charcoal filter [1] in such a way
that the arrow is pointing towards the back and is visible from
underneath.
X
Slide the activated charcoal filter into the housing.
X
Push the activated charcoal filter upwards until the filter
bracket [2] clicks into place.
28
www.bora.com
Page 29
8 Troubleshooting
X
Observe all safety and warning information (see „2 Safety“).
Operating situation Cause Remedy
The cooktop or the fan cannot be
switched on.
Odours and vapours arise when the new
cooktop is put into operation.
The fuse or automatic circuit breaker of the
electrical wiring system in the apartment and/
or house is defective.
The fuse or the automatic circuit breaker trips
several times.
The power supply is disconnected. Have a specialist electrician inspect the
This is normal on brand-new appliances. Wait a few operating hours. Contact the
Replace the fuse.
Switch the automatic circuit breaker
back on.
Call the BORA Service Team.
power supply.
BORA Service Team if the odour pers
Troubleshooting
EN
ists.
v
is displayed by the cooking zone indicator.
L
is displayed by the cooking zone indicator.
A cooking zone or the entire cooktop
switches off automatically.
The power setting is automatically shut off
prematurely.
E
is displayed by the fan level indicator.
ER03
is shown across all 4 cooking zone
indicators and the cooktop switches off
during operation.
The cooling fan continues to run after the
cooktop has been switched off.
E
is displayed by the cooking zone indicator.
F
is displayed by the fan level indicator.
The extraction performance of the cooktop
extractor has decreased.
No or unsuitable cookware has been placed on
the cooking zone.
The childproofing feature is activated. Switch off the childproofing feature (see
The operating time of a cooking zone has been
exceeded.
The overheating protection has tripped. (see the “Appliance description” chapter)
The overheating protection has tripped. (see the “Appliance description” chapter)
One or more sensor buttons are covered, e.g.
due to finger contact or by objects placed on
them.
The fan will continue to run until the cooktop
has cooled down and will then switch off
automatically.
An error has occurred in the electronic system. Switch off the cooktop power supply for
The period of use of the filters has been
exceeded.
The stainless steel grease filter is heavily
soiled.
The activated charcoal filter is heavily soiled
(BIU only).
There is an object in the air guiding housing
(e.g. cleaning cloth).
The fan is defective or a duct connection has
become loose.
Only use suitable cookware. Select the
cookware size depending on the cooking
zone (see the “Appliance description”
chapter).
the “Operation” chapter).
Put the cooking zone back into operation
(see the “Operation” chapter).
Clean the operating panel or remove
objects (see the “Appliance description”
chapter).
Wait until the cooling fan switches off
automatically.
approx. 1 minute. If the problem continues
to persist after the power supply has been
restored, write down the error number and
contact the BORA Service Team.
Replace the activated charcoal filter (with
recirculation only) and thoroughly clean
the stainless steel grease filter. In case of
heavy soiling, replacing the stainless steel
grease filter is also recommended (see
the “Cleaning and maintenance” chapter).
Clean or replace the stainless steel grease
filter.
Replace the activated charcoal filter.
Remove the trapped object.
Contact the BORA Service team.
Tab. 13.1 Resolving a fault
X
In all other instances, contact BORA After Sales Service
(see the “Warranty, technical service and spare parts” chapter).
www.bora.com
29
Page 30
EN
Decommissioning, disassembly and disposal
9 Decommissioning, disassembly and disposal
X
Observe all safety and warning information
(see „2 Safety“).
9.1 Decommissioning
Decommissioning is understood as final shutdown and
disassembly. Following decommissioning, the device can either
be installed into other units, sold on privately or disposed of.
Electricity and gas connections may only be disconnected
i
by qualified specialists.
X
To decommission, switch the device off
(see „6 Functions and operation“)
X
Disconnect the device from the power supply.
9.2 Disassembly
For removal, the device must be accessible for disassembly and
disconnected from the power supply.
X
Undo the appliance fixture.
X
Remove the silicone joints.
X
Remove the device from the worktop by lifting it upwards.
X
Remove any other accessories.
X
Dispose of the old device and any contaminated accessories
as described under “ Environmentally-friendly disposal”.
9.3 Environmentally-friendly
disposal
Disposal of transport packaging
The packaging protects the device from damage in
i
transport. The packaging materials have been selected
from environmental and disposal perspectives and are
therefore recyclable.
Returning the packaging to the materials cycle saves resources
and reduces waste volumes. Your specialist supplier will take the
packaging back.
X
Give the packaging to your specialist supplier
or
X
Dispose of the packaging properly in line with local
regulations.
Disposal of accessories
Dispose of unnecessary or used accessories (activated charcoal
filters, etc.) accordingly taking into account the regional
regulations.
Disposal of old appliance
Electrical devices marked with this label
may not be disposed of in domestic waste
at the end of their service life. They must
be disposed of at a collection point for
the recycling of old electrical or electronic
devices. You can find information from your
city or district council.
Many electrical and electronic devices still contain valuable
materials. But they also contain damaging materials which
were necessary for them to function properly and safely. These
can damage human health or the environment if disposed of
improperly or incorrectly handled.
X
Never put your old appliance in domestic waste.
X
Take the old appliance to a regional collection point for return
and recycling electrical and electronic components and other
materials.
30
www.bora.com
Page 31
Warranty, technical service, spare parts, accessories
+800 7890 0987
10 Warranty, technical service, spare parts,
accessories
X
Observe all safety and warning information (see „2 Safety“).
10.1 BORA manufacturer’s warranty
BORA provides its end customers with a 2-year manufacturer’s
warranty for its products. The end customer is entitled to this
warranty in addition to the statutory claims for defects against the
sellers of our products.
The manufacturer’s warranty applies to all BORA products
purchased by authorised BORA dealers or salespersons trained
by BORA within the European Union, with the exception of
products labelled by BORA as Universal products or accessories.
The manufacturer’s warranty starts as soon as the BORA
product is handed over to the end customer by an authorised
BORA dealer and is valid for 2 years.
By registering on www.bora.com/registration the end customer
has the possibility of extending the manufacturer’s warranty.
The manufacturer’s warranty requires expert installation (in
accordance with the valid BORA ventilation handbook and
operating instructions at the time of installation) of the BORA
products by an authorised BORA dealer. During use, the end
customer is to adhere to the specifications and instructions in
the operating manual.
In order to file a warranty claim, the end customer is to notify
their dealer or BORA of the fault and must present the receipt.
Alternatively, the end customer can provide proof of purchase by
registering on www.bora.com.
BORA guarantees that all BORA products are free from material
and production defects. The defect must exist prior to delivery
of the product to the end customer. In the event that a warranty
claim is filed, the warranty shall not commence anew.
BORA will correct defects in BORA products at its own discretion
by repairing or replacing the product. All costs for the correction
of defects under the manufacturer’s warranty shall be assumed
by BORA.
Expressly not covered by the BORA manufacturer’s warranty are:
O
BORA products that were not sold by authorised BORA dealers
or salespersons trained by BORA
O
Damage caused by non-adherence to the operating
instructions (including product care and cleaning). This
represents improper use.
O
Damage caused by normal use, e.g. traces of usage on the
cooktop
O
Damage caused by external influences (such as transport
damage, ingress of condensation, damage caused by the
elements such as a lightning strike)
O
Damage caused by repairs or attempts to repair not made by
BORA or persons authorised by BORA
O
Damage to the glass ceramic
O
Voltage fluctuations
O
Secondary damage or claims for damages beyond the defect
O
Damage to plastic parts
Legal claims, particularly statutory claims for defects or product
liability, are not limited by the warranty.
If a defect is not covered by the manufacturer’s warranty, the
end customer can employ the services of the BORA technical
service, however, they must cover the costs themselves.
The laws of the Federal Republic of Germany apply to these
warranty conditions.
You can contact us by:
O
Telephone: +49 800 7890 0987
Monday to Thursday from 08:00–18:00 and Friday from
08:00–17:00
O
Email: info@bora.com
10.1.1 Warranty extension
You can extend the warranty by registering on www.bora.com/
registration.
10.2 Service
BORA Service:
see reverse side of the operating and assembly instructions
X
In the case of faults you cannot fix yourself, contact your
BORA specialist supplier or the BORA Service Team.
The BORA Service Team will require the type designation and
serial number of your appliance
(FD number).
You can find both details on the nameplate on the warranty form
as well as on the bottom of the appliance.
10.3 Spare parts
X
Only use original spare parts for repairs.
X
Repairs may only be carried out by the BORA Service Team.
Spare parts can be obtained from your BORA
i
dealer, the BORA online service website at www.bora.
com/service or by calling the
service number provided.
10.4 Accessories
O
Stainless steel grease filter BFF
O
Air inlet nozzle GP4ED
O
Activated charcoal filter set BAKFS
O
Sealing tape UDB25
O
Cooktop frame BKR760
EN
www.bora.com
31
Page 32
004136-10002
Operating and installation instructions: Original Translation
Manufacturer: BORA Vertriebs GmbH & Co KG
The distribution and duplication of this document, as well as the use and
disclosure of its contents are prohibited unless expressly authorised.
These operating and installation instructions have been drawn up with the greatest of care. But it cannot be ruled out that subsequent technical modifications
have not yet been incorporated or the relevant content has not yet been adapted. Please accept our apologies in this eventuality. An updated version can be
requested from the BORA Service Team. Subject to printing errors and mistakes.
© BORA Vertriebs GmbH & Co KG All rights reserved.
D
BORA Lüftungstechnik GmbH
Rosenheimer Str. 33
83064 Raubling
Germany
T +49 (0) 8035 / 9840-0
F +49 (0) 8035 / 9840-300
info@bora.com
www.bora.com
A
BORA Vertriebs GmbH & Co KG
Innstraße 1
6342 Niederndorf
Austria
T +43 (0) 5373 / 62250-0
F +43 (0) 5373 / 62250-90
mail@bora.com
www.bora.com
INT
BORA Holding GmbH
Innstraße 1
6342 Niederndorf
Austria
T +43 (0) 5373 / 62250-0
F +43 (0) 5373 / 62250-90
mail@bora.com
www.bora.com
NZ
AU
BORA APAC Pty Ltd
100 Victoria Road
Drummoyne NSW 2047
Australien
T +61 2 9719 2350
F +61 2 8076 3514
info@boraapac.com.au
www.bora-australia.com.au
+800 7890 0987
Loading...