*IMPORTANT– RETAIN FOR FUTURE REFERENCE*
PLEASE READ CAREFULLY
B 2 Y Baby to Youth Cot / King Single Bed
Boori International Boori UK Limited
AUSTRALIA
27-37 Vallance Street
St Mary's NSW
2760 Australia
Ph: 02 9833 3769 Fax: 02 9673 4240
UNITED KINGDOM
Wells house, Unit 5
Woolley Barns, Woolley
Wantage, OX12 8TA UK
Ph: 44 14 8863 9500 Fax: 44 14 8863 9505
2 x Allen Keys Cot hardware and parts list
4 x
Drop side
glide pins
A
1 x Fixed side
1 x Drop side
12 x
Wooden
dowels
B
NOTE: Grooves in fixed side are
guideline marks for mattress thickness
16 x
20mm
Connecting
bolts
C
4 x
40mm
Connecting
bolts
E
Fixed side has
2 x G bolts and
2 x L capping
nuts inserted.
These remain in
the fixed side
until the cot is
converted to a
king single bed.
8 x
54mm
Connecting
bolts
G
4 x Base Supports
2 x End panels (identical)
4 x
70mm
Connecting
bolts
I
NOTE: When
standing end
panels up to
assemble cot
please make sure
you have correct
side up.
Feet need to be
attached at the
lower part of both
the end panels.
Connecting
J
4 x
80mm
bolts
1 x Base
Glide pin holes
for drop side panel
2 x Base side extensions
2 x Left cot feet
2 x Right cot feet
Holes for fixed
side panel
2 x Base extensions
V 07/06
FOR AUSTRALIA AND NEW ZEALAND (AS/NZS 2172:2003)
RECOMMENDED MATTRESS SIZE 1310mm X 750mm X 110mm
This cot has been manufactured for use with a mattress which measures 750mm wide by 1310mm long and
a maximum thickness of 120mm. The width and length are specified because it is important that the gaps
between the mattress sides and ends of the cot will not exceed 40mm. This is to minimise the risk of a child’s
limb becoming caught in the gap. The thickness of the mattress has been specified to ensure that the
depth of the cot is greater than 500mm with the mattress base in the lower position to minimise the risk of
a child climbing or falling out of the cot.
Warning:
• TO PREVENT FALLS OR SUFFOCATION THE MAXIMUM MATTRESS THICKNESS SHOULD NOT EXCEED 120MM.
• TO PREVENT FALLS, THE MATTRESS BASE OF THIS COT SHOULD BE ADJUSTED TO THE LOWEST POSITION BEFORE
THE CHILD CAN SIT UP.
• Follow the manufactu rer’s assembly instructions in detail to ensure the safety features of the cot are not
compromised.
• Ensure the cot is placed at a reasonable distance from curtains, blinds, heaters and power points.
• Keep cot free of any toys, cushions etc that could be used as a foothold or present a danger of
suffocation or strangulation.
• Keep medication, String, elastic or small items such as money out of reach from any position in the cot.
FOR THE UK (BS EN716-1:1996 BS EN716-2:1996)
IMPORTANT-RETAIN FOR FUTURE REFERENCE—READ CAREFULLY
RECOMMENDED MATTRESS SIZE 1310mm X 750mm x 110mm
If you leave the child unattended in the cot, always make sure that the dropside is in the highest position.
This cot has been manufactured for use with a mattress which measures 750mm wide by
1310mm long and a maximum thickness of 120mm. The thickness of the mattress has
been specified to ensure that the depth of the cot is greater than 500mm with the
mattress base in the lower position and 200mm with the mattress in the highest position to
minimise the risk of a child climbing or falling out of the cot.
Warning:
• TO ENSURE THE SAFETY, REGULARLY CHECK ALL THE CONNECTING BOLTS AND GLIDE PINS
MAKING SURE THEY ARE TIGHT, CARE SHOULD BE TAKEN THAT NO SCREWS ARE LOOSE
BECAUSE A CHILD COULD TRAP PARTS OF THE BODY OR CLOTHING (EG. Strings,
necklaces,ribbons for babies dummies), WHICH WOULD POSE A RISK OF STRANGULATION.
• TO PREVENT FALLS, THE MAXIMUM MATTRESS THICKNESS SHOULD NOT EXCEED 120MM.
• TO PREVENT FALLS, THE MATTRESS BASE OF THIS COT SHOULD BE ADJUSTED TO THE LOWEST POSITION
BEFORE THE CHILD CAN SIT UP.
• Follow the manufacture r’s assembly instructions in detail to ensure the s afety features of the cot are not
compromised.
• Ensure the c ot is placed at a reasonable distance from curtains, blinds, power points, heaters and
sources of strong heat.
• Keep cot free of any toys, cushions etc that could be used as a foothold or present a danger of
suffocation or strangulation.
• Keep medication, String, elastic or small items su ch as mo ney out of reach from any position in the cot.
Maintenance of your Boori Cot
• TO ENSURE THE SAFETY OF YOUR COT, REGULARLY CHECK ALL THE CONNECTING BOLTS AND GLIDE PINS
MAKING SURE THEY ARE TIGHT, CARE SHOULD BE TAKEN THAT NO SCREWS ARE LOOSE
• GLIDE PINS AND BOLTS SHOULD BE TIGHTENED EVERY FOUR TO SIX MONTHS TO ENSURE COT REMAINS
STABLE
• TO CLEAN YOUR COT USE A SOFT CLOTH DAMPENED WITH WATER
• DO NOT USE STRONG HOUSEHOLD CLEANERS
• AVOID CONTACT WITH SHARP OBJECTS
• WHEN MOVING YOUR COT DO NOT DRAG, ALWAYS LIFT AND PLACE IN POSITION
Boori COT/JUNIOR BED assembly instructions
V 07/06
Loading...