Page 1
WILT STOP
WILT STOP® is natural nontoxic product derived
from the resin of pine trees.
WILT STOP® forms a soft, clear, flexible film on
treated plants. this film protects plants from
drying out, drought, wind burn, sun scald, winter
kill, transplant shock, salt damage, while at the
same time allowing them to grow naturally.
for use on: evergreens, trees, shrubs, turf, flowers,
vegetables, bulbs, houseplants, transplants, and
dormant and growing plants.
apply: according to label instructions using trigger
or pressure tank sprayers.
one application lasts all season.
plant amending ingredient:
pinene ....................................25%
total other ingredients: ........75%
Store and transport in an upright position.
©Bonide Products, Inc. All Rights Reserved
Bonide Products, Inc.
6301 Sutliff Road
Oriskany, NY 13424
®
Page 2
Excessive moisture loss from plants causes severe wilting, shock or plant
death. It occurs in winter when drying winds and frozen ground deprive
plants of their natural moisture intake, when plant roots are disturbed
during transplanting, during periods of drought, or when Christmas trees
and greens are cut. WILT STOP® forms a protective coating which holds
moisture in on plant foliage reducing water loss during plant stress. WILT
STOP® forms a clear flexible film without interfering with plant growth. Only
one application per season is typically needed.
WILT STOP® can be used on deciduous trees, evergreens, shrubs, turf,
roses, flowering plants, vegetables, fruits, transplants, cut plants, indoor
plants, Christmas trees, and others.
SHAKE WELL BEFORE USING. SPRAY TOPS AND BOTTOMS OF
LEAVES, NEEDLES AND STEMS TO RUN-OFF. ALWAYS ALLOW WILT
STOP® TO DRY OUTDOORS IN DAYLIGHT, WASH SPRAYER WITH
WARM WATER AND DETERGENT AFTER EACH USE.
For winter kill protection Mix 1 (one) part WILT STOP® to 5 (five) parts
water. For all other uses, mix 1 (one) part WILT STOP® to 10 (ten) parts
water. Always add WILT STOP® to water, not vice versa.
For spring, summer and fall transplanting, water plants thoroughly, when
possible, before spraying with WILT STOP®. Do not spray or dip roots.
READ ENTIRE LABEL PRIOR TO USE!
INSTRUCTIONS
DILUTIONS
TRANSPLANTING
Page 3
Spray once each season, in the spring.
Spray in the late fall when temperature is above freezing so that spray
will not freeze on foliage. When spraying on arborvitae, cypress, juniper,
and cedar, be aware that if species have not sufficiently hardened off for
the winter whereby moisture retreats to the root system, moisture in plant
cells could freeze and burst if early severe freezing weather should occur.
Spray cut or live plants before bringing indoors.
Spray to extend their freshness and beauty.
Spray houseplant to reduce water requirements.
Dip or spray to prevent drying out during storage.
Spray foliage to protect plants from salt damage in salt water areas and
near roadways where salt is used to melt snow and ice.
Water plants normally. Then apply WILT STOP® to point of run-off.
Keep out of reach of children.
Store and transport in a sealed and upright position.
FOR DROUGHT AND WINDBURN PROTECTION
FOR WINTER PROTECTION
CHRISTMAS TREES, WREATHS AND GREENS
CUT FLOWERS
HOUSEPLANTS
BULBS, TUBERS, BARE ROOT STOCK AND DORMANT ROSES
SALT DAMAGE
FOR SUMMER SCALD
TIPS AND PRECAUTIONS
Page 4
Add WILT STOP® to water not water to WILT STOP®.
Never spray or dip the roots of balled or bare root plants.
Freezing does not harm WILT STOP®. Simply shake well prior to use.
Do not mix WILT STOP® with any other compound. Apply only per label
instructions.
Always soak or water transplants thoroughly prior to applying WILT STOP®.
Sprayers should be rinsed with warm soapy water immediately after each use.
Avoid overspray. Fine finishes can be stained. Wash surfaces sprayed in
error with warm soapy water. Dried film can be dissolved with kerosene.
Do not use on African violets or exotic, slow growing dwarf plants.
WILT STOP® may turn blue spruce and similar species of evergreen a green
color. If this occurs, natural coloring will return with the next season's growth.
Before using WILT STOP® on large numbers of plants, test it under your
conditions on just a few plants first.
Do not use WILT STOP® on any variety of arborvitae, cedar, cypress,
chamaecyparis, juniper, sequoia, dwarf conifer or similar plant species
without testing first.
Thorough coverage is important. Apply WILT STOP® at least 1 hour prior
to rainfall.
Sunlight is needed for the protective film to properly set.
Do not use for winter protection where temperatures drop below – 30°
centigrade.
Loading...