Page 1
Bona Edgeby
AMO230009.3 - AMO230018.3
Operating Manual
Page 2
Foreword
Bona Edge Manual
ATTENTION:
This manual contains important information on the safe use and operation
of this machine.
Carefully read through the entire user manual before you begin working
with the machine. This machine is intended for professional or commercial
use.
Failure to read this manual before operating, adjusting or servicing this
machine could cause injury or damage to persons or objects.
Anybody operating the machine should understand how to use and operate
it before starting it up.
If anything is unclear, turn to your reseller with confidence or directly to
Bona AB. Keep this manual for future reference.
This manual is an English translation of the original version in Italian.
For a new manual contact:
Bona AB
Murmansgatan 130
P.O. Box 21074
SE-200 21 Malmö, Sweden
Tel +46 40 38 55 00
www.bona.com
bona.com 2
2bona.com
Page 3
Table of Contents
Machine Specifications 4
Machine Key Symbols 5
Operator Safety 5
Storage 7
Introduction 8
Safe and correct use 8
Machine data plate 8
Commencing Operation 9
Instructions for electrical connection 9
Cable, extensions and plugs 9
Prevention Measures for User 10
Instructions on removing sawdust generated during use 10
Personal safety measures 10
Compliance with safety measures and warnings 10
Instruction on Correct Machine Use 11
Machine Warnings 12
Prohibited use 12
Starting Machine Description 13
Machine use 13
Working method 13
Starting the machine 13
Machine Adjustment Procedures 14
Wheel adjustment Bona Edge 130 mm 14
Wheel adjustment Bona Edge 220 mm 14
Handle adjustment 15
Abrasive assembly procedures 15
Routine Maintenance 17
Replacing the Velcro disc 17
Replacing the cogged belt Bona Edge 220 mm 17
Replacing the cogged belt Bona Edge 130 mm 19
Replacing to an other sanding arm 22
Replacing the carbon brushes 22
Replacing the halogen lamp 23
Replacing the wheels 23
Troubleshooting (for the user) 24
Service, Maintenance and Spare Parts 25
Service and maintenance 25
Spare parts and exploded view 25
Warranty 26
Declaration of Conformity 27
Disposal 28
3
Page 4
Machine Specifications
Bona Edge Manual
Motor Type:
Voltage (±5 %):
Frequency:
Power:
Rated Current:
Reccomended Fuses:
Motor Insulation:
Motor Protection:
Sanding Speed Disc:
Illumination:
Total Weight:
Dust Discharge:
Abrasive Disc Diameter:
Sanding Arm Length:
1 phase
230 VAC
50 Hz
2.0 kW
10 A
10 A
F
IP54
Approx. 3000 rpm normal load
20 W halogen
12.5 kg (Arm 130 mm) - 15.5 kg (Arm 220 mm)
< 1 mg / m³ air
178 mm
130 mm - 220 mm
Sanding Arm Heigth:
Hour Counter:
51 mm
< 99,999 hours
4bona.com
Page 5
Machine Symbols Key
Read the instructions
contained in this user
and maintenance
manual before using
the machine.
Hearing protection
during use is
recommended.
Operator Safety
Protection of the
airways during use
is recommended.
Hazard due
to electricity.
Hazard, keep hands away
from moving mechanical
parts.
HAZARD means: Serious injury or death may occur to the operator or others if 'HAZARD' warnings on the
machine or in this manual are ignored or not kept to. Read and follow all 'HAZARD' warnings on this machine
or in this manual.
WARNING means: Injury may occur to the operator or others if 'WARNING' notices on the machine or in this
manual are ignored or not kept to. Read and follow all 'WARNING' notices on this machine or in this manual.
CAUTION means: Damage may occur to the operator or others if 'CAUTION' alerts on the machine or in this
manual are ignored or not kept to. Read and follow all 'CAUTION' alerts on this machine or in this manual.
Failure to read the Bona Edge machine manual before operating, adjusting or performing maintenance
operations on the machine could cause injury or damage to persons or objects.
Anyone operating the machine should understand how to use and operate it before starting it up.
KEEP AWAY FROM CHILDREN
Children should be supervised to ensure that they do not play with the appliance. This machine is not
intended for use by persons (including children) with reduced physical, sensory or mental capabilities,
or lack of experience and knowledge unless they have received instructions regarding the use and are
supervised by a person responsible for their safety.
55
Page 6
Operator Safety (Cont.)
Sanding may create an explosive environment. Cigarettes, cigars, pipes, lighters, pilot flames, or any other
source of fire may create an explosion, if lit during sanding operations. All sources of ignition should be
removed entirely from the work area.
Poorly ventilated work areas may create an explosive environment, when some combustible materials
(solvents, thinners, alcohol, fuel, some paints, wood dust, etc) are present in the atmosphere. Floor sanding
may cause various materials and fumes to ignite. Read the manufacturer’s instructions for each chemical
product used and establish its combustibility. Always keep the work area well-ventilated.
Striking nails when sanding may generate an explosion or fire. Always ensure all nails are sunk before
sanding surfaces.
Serious injury and/or death due to electrocution may occur, if the power supply circuit trips repeatedly or is
undersized. Have the fuses, safety circuit and power supply line checked by an authorized electrician.
Performing maintenance and/or repairing the machine, when it is not fully disconnected from the power
supply, may cause serious injury and/or death due to electrocution. Disconnect the power supply before
carrying out any maintenance and/or repair work.
Bona Edge Manual
The use of this machine on a circuit which is not grounded may cause serious injury and/or death due to
electrocution. Never disconnect or disable the grounding conductor. Consult an electrician, if the ground
conductor is missing or it is suspected that the circuit is not suitably grounded.
The use of this machine with a damaged power supply cable may cause electric shock. Check the
power supply cable regularly for damage, such as splitting or wear and tear. DO NOT use
the machine, if the power supply cable is damaged. DO NOT use the electric cable to move
the machine. DO NOT close a door on cord. DO NOT pull cord around sharp edges or corners.
DO NOT unplug by pulling on power supply cable. To unplug grasp the plug. DO NOT handle plug or operate
machine with wet hands. DO NOT put any objects into motor openings.
Serious injury and/or death due to electrocution may occur if the machine runs over the power supply
cable and it becomes damaged. Keep the cable away from the sanding tool. Always keep the power supply
cable raised above the machine and sand away from the power supply cable.
The moving parts on this machine may cause serious injury and/or damage. Keep hands, feet and loose
clothing away from all moving parts of the machine.
Operating the machine without all guards, doors, or covers in place can cause an injury or damage.
DO NOT pass with the machine on objects that are hot, burning or smoking, such as cigarettes, matches or
cinders.
6bona.com
6
Page 7
Operator Safety (Cont.)
Performing maintenance or replacing the dust bag may cause injury to the operator or people nearby, if the
machine is connected to the power supply. Always unplug the machine when not in use.
DO NOT use solvents or other flammable products to clean this machine.
Dry use only. DO NOT use for liquid recovery, which could result in motor failure, electric shock,
and electrocution.
Never become distracted during sanding operations, check what is happening continually. Use common
sense. DO NOT use the machine, if you are tired, have consumed alcohol or have taken medication that may
aect your judgement or your body control.
DO NOT smoke during sanding operation.
DO NOT use this machine to sand furniture.
DO NOT put any objects into openings. DO NOT use with blocked openings. Keep free from dust, lint, hair or
anything that may reduce airflow.
Storage
It is advisable to store the machine in its original packaging. Doing so makes it possible to form a column of three packages maximum, with one
on top of the other.
If the machine is removed from the original packaging and is not used for some time ensure the wheels and disc are not in contact with the
ground.
This equipment is for dry use only and must not be used or kept outside in wet conditions. Store the
machine in a dry building, otherwise the machine could be damaged.
Storage temperature from -20°C to 50°C.
77
Page 8
Introduction
Bona Edge Manual
Safe and correct use
This instruction manual should be read carefully before using the Bona Edge edge sander for the first time.
The instruction manual contains important information on safety and preventing improper use of the machine and will resolve any doubts
or questions, making possible to operate the machine safely and with ease. Removing safety features could cause death or physical injury.
Familiarize yourself with the machine before using it for the first time.
If a situation arises which has not been described in this manual, contact your distributor or Bona Representative.
The Bona Edge machine is suitable for the dry sanding of floors. Any other use without the consent of the manufacturer is prohibited. DO NOT use
on wet floors.
See ‘Machine Warnings’ on page 11.
Keep hands and clothing away from moving mechanical parts.
Machine data plate
The following information can be found on the machine data plate:
1) Name of the manufacturer
2) Machine model and P/N
3) Year of manufacture (see 7)
4) Motor power
5) Supply voltage and Frequency
6) Rated current
7) Serial number:
• The first two numbers refer to the year of manufacture (15= 2015)
• The second group of three numbers indicates the day of the year the
machine was manufactured (185 = July 4th)
• The last two numbers indicate the progressive number of machines
produced that day of manufacture
(44= 44th machine produced that day)
8bona.com
8
Page 9
Commencing Operation
Instructions for electrical connection
This machine only operates with the voltage and frequency shown on the machine data plate. Before
connecting the cable to the power supply ensure the correct voltage and frequency are available.
DO NOT expose the machine to rain. This machine is intended for dry use only.
Keep the machine in a dry building and DO NOT use it in damp or wet places.
If the machine is not connected correctly to the electricity network, death due to electrocution may
occur. To prevent electric shocks always use a grounded three wire electrical system. For maximum
protection against electric shocks use a circuit protected with a dierential cut-out switch.
Tampering with the grounding plug in any way may result in death from electrocution. DO NOT cut,
remove or break the grounding plug. If the socket does not match the plug consult a qualified electrician.
If the machine is used with a damaged plug or power supply cable, death may occur from electrocution.
If cables or plugs are worn or damaged in any way, have them replaced by the manufacturer or certified
machine repair center in order to prevent risks to safety.
Cables, extensions and plugs
Only use approved cables. The maximum recommended cable length is 10 m; for greater lengths use cables with a
larger cross-section.
Using the machine with unsuitable and/or excessively long cables may cause injury or damage to people or
objects.
The machine must never be moved using its cable and the cable must never be pulled when disconnecting
from the socket.
Keep the cable away from sources of heat, oil and sharp edges.
MACHINE WITH 230 V~50 Hz MOTOR 2.0 kW
For machines with a 230 V~50 Hz motor, a HO5VV-F-3x2,.5 mm2 HAR-approved power supply cable must be used along with an approved SCHUKO
2P+E 16 A 200÷250 V plug.
9
Page 10
Prevention Measures for Users
Instructions on removing sawdust generated during use
Sawdust can ignite spontaneously and cause injury or damage. It must be disposed of appropriately. Always
empty the sawdust into metal containers which are located outside the building.
Sawdust can ignite spontaneously and cause injury or damage. Empty the contents of the dust bag when it
is 1/3 full. Empty the dust bag at the end of each machine use. Never leave the dust bag unattended when it
contains sawdust. Do not empty the contents of the dust bag above a fire.
For minimized dust environment use a vacuum cleaner intended for wooden dust.
Personal safety measures
Sawdust can spread through the air and be inhaled when using the sanding machine. Always wear a dust
mask of at least class P2, when using the sanding equipment.
Bona Edge Manual
The eyes and/or body may suer injury if personal safety clothing is not used. It is adviceble to wear safety
goggles, protective clothing during sanding operations.
Lengthy exposure to noise levels during sanding operations may damage the hearing. Always use EN-ISO
approved ear protectors (earmus) during sanding operations.
Compliance with safety measures and warnings
Using the machine when not fully assembled may cause injury or damage to people or objects. DO NOT
use the machine when it is not fully assembled. Keep all fittings tightly closed. Maintain machine settings in
accordance with the specifications.
Failure to comply with instructions on this machine and in this manual may cause serious injury and/or
damage. Read and comply with all safety instructions. Ensure that all plates, labels,
warnings and instructions are secured to the machine. New plates can be obtained from an authorized
Bona dealer.
Injury or damage may occur if maintenance operations or repairs are carried out by any unauthorized
personnel.
10bona.com
Page 11
Instructions on Correct Machine Use
Read this manual carefully and become familiar with the machine.
The equipment is suitable for industrial use (e.g. in hotels, schools, hospitals, oices, factories and shops).
The following information highlights particularly hazardous situations for the operator and/or machine. Understand when these conditions may be
present. Removing safety features could cause death or physical injury. Take all steps necessary to instruct personnel who may use the machine.
Report any damage on the machine or incorrect operation immediately.
1) Keep hands and clothes away from rotating parts.
2) Keep hands on the handle when the motor is operating.
3) DO NOT leave the machine unattended when the motor is operating.
4) Always disconnect the power supply cable from the machine before performing maintenance.
5) Transport the machine with care, due to the machine weight.
6) Always use the machine in well-ventilated areas.
7) Always keep the work area well-lit.
8) Always dispose of the sanding dust appropriately.
9) DO NOT detach the dust bag when the motor is operating.
10) Always dispose of the sawdust appropriately.
11) Use the type and amount of abrasive specified in the instruction manual.
12) The use of accessories other than those recommended in this manual may cause injury.
13) The machine is for indoor use only.
Machine Warnings
Prohibited use
Children should be supervised to ensure that they do not play with the appliance. This
machine is not intended for use by persons (including children) with reduced physical,
sensory or mental capabilities, or lack of experience and knowledge unless they have
received instructions regarding the use and are supervised by a person responsible for
their safety.
This equipment is not suitable for collecting hazardous dust.
Using the machine to move objects or moving on an incline may cause injury or damage. The machine
must only be used to sand dry floors which are level or have a maximum incline of 2%. DO NOT use the
machine to sand furniture.
Work surfaces may be seriously damaged if the machine is left turning on one point while the tool is in
contact with the surface. To avoid damaging the surface approach the cutting line carefully. DO NOT stop
when lowering and raising the equipment, keep moving at constant speed.
11
Page 12
Starting Machine Description
Bona Edge Manual
Machine use
The machine is intended for the edge sanding of wooden floors. It maybe used on newly laid and untreated floors and existing floors that have been
treated with lacquer or oil.
The main function of the machine is to serve as a complement to a belt or a drum sander for sanding edges.
The machine has been thoroughly checked and approved before leaving the factory.
Working method
When sanding hold the machine, use both handles and move the machine in circles in the
direction of rotation over the surface which is to be sanded. It is important that the machine rests
on three points, both the wheels and the sanding disc.
The best result is obtained by letting the machine work with its own weight.
When using fine abrasives you must be careful not to make any burn marks due to high friction
created.
In addition to the points noted the sanding must be adapted to the type, patter and composition
of the floor.
Starting the machine
1) Become familiar with the machine and read all instructions &
safety notices. Ensure that all operators read this manual.
3) If using DCS, connect DCS pipe and suction pipe of the machine. If
using a dust bag, place the dust bag on the suction pipe.
2) Bring the machine to the place of work.
4) Fit the disc in accordance with the 'Abrasive Assembly
Procedures' (pg.15-16).
12bona.com
Page 13
Starting Machine Description
Starting the machine (Cont.)
5) Locate the power supply. The socket must be compatible with the
plug. To avoid electrical hazards the socket must be grounded with
a 20 Amp fuse. Connect the plug to the socket.
7) Keep the machine moving when the abrasive disc is lowered
and in contact with the work surface.
6) Raise the disc so that the machine is only resting on the floor with
its wheels. Then, press the starting/stopping button on the side of
machine..
8) To stop the machine, raise the disc so that the machine is only
resting on the floor with its wheels. Then press the starting/
stopping button on the side of machine.
The disc does not stop immediately! Take care not to touch it with any part of the body during
this phase.
Allow the motor to "rest" during periods of heavier use.
13
Page 14
Machine Adjustment Procedures
Wheel adjustment Bona Edge 130 mm
1) The distance between the underside of the motor
underside of the motor bracket and the floor should
be approx. 83 mm on the left side and 75 mm on the
right for standard arm.
Wheel adjustment Bona Edge 220 mm
1) The distance between the underside of the motor
bracket and the floor should be approx. 78 mm on
both sides.
Bona Edge Manual
Footprint should be as above to get the best result.
Note! If the whole disc is flat and in full contact with the floor it
will create excessive resistance in the motor, leave circular scratch
marks, and the machine will be hard to handle.
Dust collection
1) For minimal dust discharge Bona's original dust
bags shall always be used. The dust bag must be
emptied when it is filled to max 1/3.
2) When emptying the dust bag, remove the dust tube,
together with the dust bag, completely, open the
zipper and empty the contents.
14bona.com
Page 15
Machine Adjustment Procedures (Cont.)
Handle Adjustment
1) The angle of the handles can be adjusted for a more
comfortable working position. Use Torx wrench T30.
Keep the handle clean and free from grease.
Abrasive assembly procedures
1) Ensure the electric cable is disconnected from the power.
3) Remove the worn abrasive paper disc (A) from Velcro disc.
5) Attach the abrasive disc securing it well to the Velcro.
2) Lay the machine carefully on its left side.
4) Ensure the surface of the Velcro disc is clean and
position a new 178 mm diameter abrasive disc.
6) Check that the sanding disc is centered.
15
Page 16
Machine Adjustment Procedures (Cont.)
Abrasive assembly procedures (Cont.)
If abrasive paper with hole is to be used, proceed as follows:
Bona Edge Manual
1) Ensure the electric cable is disconnected from the power.
3) Remove the nut and tapered washer (A) with box spanner
NV 17, keeping disc (B) stationary.
5) Secure the abrasive disc using the nut and tapered
washer, keeping disc stationary.
2) Lay the machine carefully on its left side.
4) Ensure the surface of the Velcro disc is clean and
position a new 178 mm diameter abrasive disc.
6) Check that the sanding disc is centered.
Only use discs with a diameter of 178 mm.
Regularly check the sanding disc.
If the sanding disc is worn out or has become clogged by lacquer or paint, the sanding result deteriorates and the
surface of wood may become discolored.
16bona.com
Page 17
Routine Maintenance
To keep the machine in good working condition the following items must be checked and serviced regularly.
The machine may never be cleaned using a high pressure washer or hose.
Replacing the Velcro disc
1) If Velcro disc is worn, scrape the disc o with a knife.
3) Glue a new Velcro disc on the steel plate.
2) Clean the steel disc with alcohol or similar.
4) Check that the disc is centered: a disc that is not
centered may cause unbalances and vibrations.
Replacing the cogged belt Bona Edge 220 mm
1) Remove the 4 belt cover screws.
2) Remove the 4 bolts by the motor bracket.
17
Page 18
Routine Maintenance (Cont.)
Replacing the cogged belt Bona Edge 220 mm (Cont.)
Bona Edge Manual
3) Lift the motor bracket of the sanding arm .
5) Fit a new cogged belt on the small pulley. Then fit the pulley
and fan along with the plate on motor shaft.
Make sure that the plate is not clamped between the motor
bracket and the sanding arm.
4) Remove the screw and washer, loosen the stop screw and then
remove the fan together with the plate.
6) Fit the cogged belt on the big pulley.
7) Refit the bolts without tighten them. Tighten the cogged belt
tension by pulling the motor bracket backwards relative to
the arm.
8) Make sure the fan and belt go freely by spinning the
sanding disc. Tighten the bolts. Refit the belt cover.
18bona.com
Page 19
Routine Maintenance (Cont.)
Replacing the cogged belt Bona Belt 130 mm
1) Undo the 2 belt cover screws.
3) Remove the pulley screw.
2) Loosen the 4 bolts in the motor bracket.
4) Gently tap with a center punch to loosen the pulley.
5) Remove the sanding arm.
6) Remove screw and washer as well as the stop
screw keeping the ventilator and cover plate on
motor shaft.
19
Page 20
Routine Maintenance (Cont.)
Replacing the cogged belt Bona Edge 130 mm (Cont.)
Bona Edge Manual
7) Remove the pulley/ventilator together with the belt and
cover plate.
9) Make sure that the cover plate is fitted in its right position.
8) Mount a new belt together with the ventilator and
cover plate.
10) Tighten the screws and washer as well as the stop screw.
11) Place the pulley in its right position.
12) Remount the sanding arm.
20bona.com
Page 21
Routine Maintenance (Cont.)
Replacing the cogged belt Bona Edge 130 mm (Cont.)
13) Replace the 4 screws.
N.B. Do not tighten the screws!
15) Tighten the 4 screws while holding the sanding arm in its
position.
14) Place a screwdriver in the hole and press forward
to tighten the belt.
16) Remount the Velcro disc, pulley screw and the nut
for the Velcro disc.
N.B. Tighten the pulley screw very hard!!
17) Remount the belt cover.
21
Page 22
Routine Maintenance (Cont.)
Bona Edge Manual
Replacing to an other sanding arm
1) Proceed in the same way as for 'Replacing the cogged belt '.
Replacing the carbon brushes
Regularly check the carbon brushes. The brushes were out more quickly at higher loads. And should be changed in
pair after approx. 100 hours normal operating time.
1) Open the carbon brush cover with i.e. a coin
3) Replace the carbon brush and put the cover back on.
2) Remove the carbon brush cover.
4) The carbon brushes stops automatically and can not below
the marking.
22bona.com
Page 23
Routine Maintenance (Cont.)
Replacing the halogen lamp
1) Remove the screw (A) on the rubber gasket for glass.
3) Replace the halogen lamp.
2) Remove the 2 screws on the either sides of cap
Bona Edge.
Replacing the wheels
1) Remove the nut holding the wheel pin with a screwdriver (A).
23
Page 24
Troubleshooting (for the user)
Bona Edge Manual
PROBLEM
The machine does not
start
The sanding disc does
not rotate
The machine is faltering
The machine is heavily
vibrating
Uneven sanding
The lamp is not working
CAUSES SOLUTIONS
No power Replace to an other wall socket
Broken cable Replace the cable
Rotation of the sanding disc is impossible
The cogged belt is broken/worn out Replace cogged belt and if necessary replace the pulley
The carbon brushes are worn out Replace the carbon brushes
The carbon brushes are broken Replace the carbon brushes
The carbon brushes are binding
O center sanding disc Centre the sanding disc
Damaged ventilator Replace the ventilator
Badly adjusted wheels Adjust the wheels
Unevenly worn wheels Replace the wheels
The wheels are binding Clean or change the wheels
The sanding disc is loose
Binding sanding disc
The steel disc is faltering
The lamp is damaged Replace the lamp
Rotate the sanding disc, remove possible blockages and
check that the ventilator runs smoothly
Clean the carbon brush channel or replace the carbon
brushes
Fix or adjust the disc or replace the Velcro disc or Replace
the screw
Replace the steel plate
24bona.com
Page 25
Service, Maintenance and Spare Parts
Service and maintenance
Bona Edge is a high quality machine and is tested by authorized test sta at the factory before delivery. However, electrical and mechanical
parts wear down and age during long-term use.
In order to keep the machine in a safe and functioning condition, service must be performed every 250 work hours or least once a year.
This service includes control of wheels, cable stand, motor, tension device, sanding disc function is controlled.
Only Bona's original parts may be used because the machine is considered unique, otherwise safety functions can become impaired.
Always disconnected the power cable to the machine before it is cleaned, tools are changed, maintenance is performed or when worn
parts are replaced.
When you contact Bona or sta approved by Bona in the event of a fault or to order spare parts, always specify the type and serial number
of your machine. This information is located on the data plate of the machine.
All maintenance must be done on neutral machine!
Unplug from the wall outlet. Check cable and connectors regularly. Always replace a damaged cord (slots,jacks or cable connections) with
a new original cable.
Spare parts and exploded views
On the Internet, you will find a list of spare parts and exploded views for Bona Edge and other machines in our product range.
Visit http://spareparts.bona.com/
During the factory warranty period, repairs may only be carried by Bona or sta approved by Bona. Other repairs (after the warranty period)
of mechanical or electrical parts on the machine may only be carried out by Bona or sta approved by Bona who has experience and
knowledge concerning safety regulations.
25
Page 26
Warranty
Bona Edge Manual
There is a 24 month factory warranty (from the date of invoice) against material and manufacturing faults.
In the event of a warranty claim, the machine or agreed upon part must be returned to Bona or sta approved by Bona with paid freight for
warranty testing and for potential repair or replacement under warranty.
During the factory warranty period, repairs may only be carried out by Bona or sta approved by Bona. We do not undertake any other form of
compensation or liability to damages.
THE WARRANTY DOES NOT COVER
•
Consumable materials such as wheels, electrical cables, abrasives, lamps, etc.
•
Indirect damage, damage and errors that occur due to external damage, accidents, and/or repairs performed outside of our knowledge and
approval, or damages for another reason outside of our control.
•
Transport damage or transport costs. In the event of transport damage it is up to the receiver to contact the relevant transport company for
compensation.
•
Cases of incorrect use, overloading, carelessness or poor maintenance
•
The use of parts produced by another company outside of our control.
•
Electrical components, if the voltage variations are beyond those set out in the technical specification.
•
If payment for the machine is not made according to the agreement.
26bona.com
Page 27
Declaration of Conformity
2006/42 EC, 2014/30 EU, 2011/65 EU, 2012/19 EU
We
Registered Headquarters
Via Circonvallazione Est. 2/6
27023 Cassolnovo (PV) - Italy
Manufacturer and entity authorized to compile and maintain the technical file,
declare that under our sole responsibility the product
KUNZLE & TASIN S.r.l.
Business Management and Production Site
Via Cajkovskij, 14
20092 – Cinisello Balsamo (MI) - Italy
Bona Edge
EDGE SANDER
to which this declaration refers, is compliant with the following Directives:
2006/42 EC (Machinery Directive), 2014/30 EU (EMC Directive), 2011/65 EU (RoHS Directive), 2012/19 EU (WEEE Directive).
The product is compliant with the following harmonized standards:
Safety of machinery - General principles for design - Risk
assessment and risk reduction - EN ISO 12100
- Requirements for household appliances, electric tools and similar
apparatus - Part 2: Immunity - EN 55014-2
Household and similar electrical appliances - Safety - Part 1:
General requirements - EN IEC 60335-1
Household and similar electrical appliances - Safety - Part
2-67: Particular requirements for floor treatment machines, for
commercial use - EN IEC 60335-2-67
Electromagnetic compatibility (EMC):
- Requirements for household appliances, electric tools and
similar apparatus - Part 1: Emission - EN 55014-1
- Part 3-2: Limits - Limits for harmonic current emissions (equipment
input current ≤ 16 A per phase) - EN IEC 61000-3-2
- Part 3-11: Limits - Limitation of voltage changes, voltage fluctuations
and flicker in public low-voltage supply systems - Equipment with
rated current ≤ 75 A and subject to conditional connection - EN IEC
61000-3-11
CASSOLNOVO (PV) – 07/07/2014
(The place and date of issue) Michela Caresana - CHIEF EXECUTIVE OFFICER
27
Page 28
Disposal
Smaltimento di apparecchiature da rottamare da parte di privati nell’Unione Europea. Questo simbolo che appare sul prodotto o
sulla confezione indica che il prodotto non deve essere smaltito assieme ad altri rifiuti domestici. Gli utenti devono provvedere allo
smaltimento delle apparecchiature da rottamare, portandole al luogo di raccolta indicato per il riciclaggio delle apparecchiature
elettriche ed elettroniche. La raccolta e il riciclaggio separati dalle apparecchiature da rottamare in fase di smaltimento favoriscono
la conservazione delle risorse naturali e garantiscono che tali apparecchiature vengano rottamate nel rispetto dell’ambiente e della
tutela della salute. Per ulteriori informazioni sui punti di raccolta delle apparecchiature da rottamare, contattare il proprio comune
di residenza, il servizio di smaltimento dei rifiuti locale o il negozio presso il quale è stato acquistato il prodotto. Specifica etichetta
fissata sulla macchina indica che il prodotto comporta requisiti speciali di smaltimento e l’eventuale presenza di una fonte di
alimentazione esterna.
Disposal of Waste Equipment by Users in Private Households in the European Union. This symbol on the product or packaging
indicates that it must not be disposed of with other household waste. It is your responsibility to dispose of your waste by bringing
it to a designated collection point that recycles electrical and electronic equipment waste. The separate collection and recycling
of waste at the time of disposal helps to conserve natural resources and ensures it is recycled in a manner that safeguards health
and the environment. For more information about where to take waste equipment for recycling, please contact your local council
oice, household waste disposal service or retailer where you purchased the product. Specific label attached to the machine
indicates that the product has special disposal requirements and possible presence of a power supply.
Entsorgung von Ausschusselektrogeräten durch Benutzer in privaten Haushalten in der EU. Dieses Symbol auf dem Produkt
oder dessen Verpackung gibt an, dass das Produkt nicht zusammen mit dem Restmüll entsorgt werden darf. Es obliegt
daher Ihrer Verantwortung, das zum Verschrotten bestimmte Gerät an einer für die Entsorgung oder Wiederverwertung von
Elektrogeräten aller Art entsprechenden Stelle abzugeben. Die separate Sammlung und das Recycling Ihrer zur Entsorgung
bestimmten Elektrogeräte trägt zum Schutz der Umwelt bei und gewährleistet, dass sie auf eine Art und Weise recycelt
werden, die keine Gefährdung für die Gesundheit des Menschen und der Umwelt darstellt. Für weitere Informationen darüber,
wo Sie alte Elektrogeräte zum Recyceln abgeben können, setzen Sie sich sie mit den örtlichen Behörden, Wertstohöfen
im Kontakt oder fragen Sie dort, wo Sie das Gerät erworben haben. Die an der Maschine angebrachte spezifische Etikette
zeigt an, dass das Produkt spezielle Entsorgungsvorschriften beachten muss und dass eine externe Stromquelle eventuell
vorhanden ist.
Bona Edge Manual
Évacuation des équipements usagés par les utilisateurs dans les foyers privés au sein de l’Union européenne. La présence
de ce symbole sur le produit ou sur son emballage indique que vous ne pouvez pas vous débarrasser de ce produit de la
même façon que vos déchets courants. Au contraire, vous êtes responsable de l’évacuation de vos équipements usagés
et à cet eet, vous êtes tenu de les remettre à un point de collecte agréé pour le recyclage des équipements électriques
et électroniques usagés. Le tri, l’évacuation et le recyclage séparés de vos équipements usagés permettent de préserver
les ressources naturelles et de s’assurer que ces équipements sont recyclés dans le respect de la santé humaine et de
l’environnement. Pour plus d’informations sur les lieux de collecte des équipements usagés, veuillez contacter votre mairie,
votre service de traitement des déchets ménagers ou le magasin où vous avez acheté le produit. Étiquette spécifique fixée à
l’arrière du produit, signale qu’il doit être évacué selon une procédure particulière et la présence d’une alimentation externe.
28bona.com
Page 29
Additional Notes
29
Page 30
Additional Notes
Bona Edge Manual
30bona.com
Page 31
Additional Notes
31
Page 32
2016 Edition
bona.com
Loading...