bolid UO-4S Revision 02 User Manual

The Bolid Company, Russia; 4 Pionerskaya Str., Korolev, Moscow Region 141070

Tel./Fax: [phone] (PBX), 777-40-20, 516-93-72

E-mail:

[e-mail], http://bolid.ru

Orion ISS

GSM Four-Input Alarm Panel

UO-4S Rev.02

User’s Manual

This User’s Manual is intended to help for studying operability and maintenance principles of

UO-4S Revision 02 GSM Four-Input Alarm Panel.

Please read the instructions from this manual completely before connecting, adjusting, oper­ating, or maintaining this device

The following terms are used throughout the Manual:
Alarm Loop: The electrical circuit with non-addressable fire or intrusion detectors (or other non-

addressable devices) included. Actuation of a single detector brought in an alarm loop
causes activation of the loop as a whole, so the actuated detector can be located only with
the accuracy of an alarm loop.

Zone: A minimum part of the security and safety installation that can be monitored and controlled

independently. Depending on the context, the term “zone” in an Orion ISS can be understood
as an alarm loop, an addressable detector, a monitored circuit of an input module etc.

Partition: A number of zones that can be controlled by user as a whole. As a rule, zones are

combined into partitions depending on their locations (e.g., one partition can involve all
zones in a single premise)

Arm/Disarm: This action means activation or termination of monitoring of defense zones and

triggering alarms

Integration Time: A time interval during which alterations of loop resistance are not considered as

loop’s being activated and the alarm loop doesn’t proceed to an alarm status

Network Address (Address): A unique number of the device (from 1 to 127) within a local RS-485

Orion ISS Network

3

Table of Contents

General ................................................................................................................................................ 5

Specifications ...................................................................................................................................... 6

Standard Delivery .............................................................................................................................. 7

Operation Principles .......................................................................................................................... 8

General Layout and Main Functions ....................................................................................... 8

Operation Modes .................................................................................................................... 9

Indication .............................................................................................................................. 11

Alarm Loops ......................................................................................................................... 13

Relay Control ....................................................................................................................... 14

Credential Programming Mode ............................................................................................. 15

Arming and Disarming by means of Dallas iButtons .................................................................. 17

Controlling UO-4S Remotely by SMS ...................................................................................... 18

Inspecting Panel Operation in the Test Mode ........................................................................... 19

Transmitting Notifications ........................................................................................................ 20

Mounting ........................................................................................................................................... 23

Mounting the Device ............................................................................................................. 23

Programming .................................................................................................................................... 27

Programming UO-4S ............................................................................................................ 27

Running Configuration Tool .................................................................................................. 28

Tab «Device» ......................................................................................................................... 29

Tab «Alarm Loops» ................................................................................................................ 32

Tab «Telephones» ................................................................................................................... 33

Tab «Message Filter» .............................................................................................................. 36

Tab «Credentials» .................................................................................................................. 37

Tab «Zones and Partitions» ..................................................................................................... 40

Tab «Message Descriptors» ..................................................................................................... 41

Tab «GPRS Settings» .............................................................................................................. 42

Maintenance ...................................................................................................................................... 44

Storage, Transportation, and Warranty ........................................................................................ 45

Storage ................................................................................................................................ 45

Transportation ...................................................................................................................... 45

Warranty .............................................................................................................................. 45

Appendices ........................................................................................................................................ 46

4

Appendix A. Contact ID Protocol .......................................................................................... 46

Appendix B. User’s SMS ...................................................................................................... 48

Appendix C. Egida-2 SMS ................................................................................................... 49

Appendix D. Egida-3 SMS ................................................................................................... 50

Appendix E. Voice Messages .............................................................................................. 53

Manufacturer Data .......................................................................................................................... 54

5

GENERAL

UO-4S Revision 02 GSM Four-Input Alarm Panel (hereinafter referred to as the UO-4S or the
panel) is designed to be used in centralized and standalone intrusion and fire alarm systems for industrial,
business, and residential premises (enterprises, banks, offices, hospitals, shops, warehouses, residential
buildings, etc.).

The UO-4S can operate both in standalone mode and as part of an Orion integrated security
system as a device transmitting notifications through GSM cellular communication channels.

In accordance with classification of Russian Standard ГОСТ Р 53325-2012 the UO-4S rev.02
panel can be used as:

1. An object terminal device;

2. A module in a modular control and indicating equipment consisting of S2000M

Monitoring and Control Panel, S2000-SP1 Executive Relay Module, and UO-4S Revision 02 Four­Input GSM Alarm Panel.

For both the applications the UO-4S must be powered by an external battery backed power
supply which meets the requirements of ГОСТ Р 53325-2012.

It is not allowed to use relay outputs of the UO-4S to control actuators of automatic fire­fighting equipment.

There are no potential hazard circuits within the panel.
The design of the panel meets the requirements of electric and fire safety in line with

Russian Standards ГОСТ 12.2.007.0-75 and ГОСТ 12.1.004-91.
The panel is designed to provide its fire safety while emergency operating and on

violations of operation rules in accordance with Russian Standard ГОСТ 12.1.004-91.
Do SHUT OFF power from the panel before mounting, installing, and maintaining this

one.
Mounting and maintenance of the panel should be carried out by persons with the second

or higher electric safety qualification level.

6

SPECIFICATIONS

Alarm Inputs (Alarm Loops) 4 Initiating Device Circuits

Input voltage in the quiescent mode 6 to 12 V
Integration Time 300 ms
Max current drawing through an alarm loop 12 mA

Max resistance of wires without regards to termination
resistance

1 kOhm for intrusion alarm loops,

100 Ohm for fire alarm loops
Min leakage resistance between the alarm loop wires or
between each wire and the earth

20 kOhm for intrusion alarm loops,

50 kOhm for fire alarm loops

Outputs 3 Relay Outputs

Max Switched Current

1 A dc

0.5 A ac

Max Switched Voltage

24 V dc

100 V ac
Max Switched Power 10 W

External Reader Dallas iButton Reader

Max number of readers connected in parallel 4
Max number of light indicators to be connected to the

LED terminal

1
Distance between the UO-4S and the reader 100 m max at wire diameter at least 0.5 mm

Credential Memory Capacity 16 codes

Communication Port RS-485

Protocol Orion

Non-volatile Event Log

128 events for transmission via GSM channel

60 events for transmission over RS-485 interface

Input Power An external uninterrupted power supply

Rated Voltage 10.2 V to 15 V

Consumed Current

Max values:

150 mA in the quiescent mode

200 mA when sending a notification

1 A is the peak consumed current

Resistance to Climatic Effects Category 03 in line with ОСТ 25 1099-83

Operating Temperatures

Minus 30°C to +50°C
Relative Humidity

Up to 98% at +25°C
Ingress Protection Rating IP20

Overall Dimensions

156 mm ×××× 107 mm ×××× 39 mm

Weight About 0.3 kg

7

STANDARD DELIVERY

Item Q-ty

UO-4S Revision 02 GSM Four-Input Alarm Panel 1 pc.
Antenna 1 pc.
Installation Manual 1 pc.
Datasheet 1 pc.
iButton 1 pc.
Half-round head woods screw 3×25 3 pcs.
Wall plug 6х30 S 3 pcs.
DIN 7982 flat head tapping screw with cross drive 2.2×6.5 1 pc.
Resistor MF 1/2W-8K2-5% 4 pcs.

UO-4S-to-PC connecting cable 1 pc.

If an external antenna should be installed with the device then the one of the following products can be
provided in addition:

Product Description

Antenna ANT GSM ADA-0071-SMA

GSM dual-band magnetic mount antenna. Gain: 4 dB.
Cable length: 2.5 meters.

Antenna ANT GSM ADA-0062-SMA

GSM dual-band glass mount antenna. Gain: 2.5 dB.
Cable length: 2.5 meters.

Antenna ANT GSM ADA-0070-SMA

GSM dual-band magnetic mount antenna. Gain: 2 dB.
Cable length: 2.5 meters.

The device is not designed to be used in aggressive or dust environments or in explosion hazardous

premises. The ingress protection rating is IР20 in line with Russian Standard ГОСТ 14254.

As to resistance to mechanical attacks the device falls into the 03 placement category in accordance

with Russian Standard ОСТ 25 1099-83.

As to electromagnetic emission and resistance to industrial radio interference the panel meets the

requirements of at least third severity level in line with Russian Standards ГОСТ Р 50009,

ГОСТ

30804.4.2

, ГОСТ Р 51317.4.3.

The mean time between failures of the device in quiescent mode should be at least 35000 hours

which is equivalent to the probability of no failure 0.97 within 1000 hours.

The probability of a failure which can trigger a false alarm response of the device is no more than

0.01 per 1000 hours.
The average lifetime of the device is 10 years.

The content of precious materials: no need to account for the storage, disposal and recycling.
UO-4S rev.02 User’s Manual can be downloaded from the company site http://bolid.ru in the

section PRODUCTS at the page of UO-4S rev.02.

8

GENERAL LAYOUT AND MAIN FUNCTIONS

Figure 1. UO-4S Layout

The UO-4S comprises the following hardware elements:

• Tamper switch;

• Beeper;

• Seven information LEDs;

• XР2 Mode Select jumper;

• XР3 620 Ohm pull-up resistor jumper;

• Two slots for primary (the lower one) and backup SIM cards;

• 25-input terminal block for connecting a power supply, RS-485 interface bus, a 220V monitoring

circuit, an operating loop, four alarm loops, three actuation devices, and a reader for reading
iButtons or Proximity cards;

• Terminal blocks for connecting a microphone/speaker.

The main functions of the UO-4S are:

•••• Monitors conditions of four inputs (alarm loops).

•••• Monitors for 220 V mains power conditions (closing the contacts 5 (“Кпит”) and 6 (“0 В”)

means a mains failure while opening of these contacts means restoring power conditions).

•••• Controls three relay outputs depending on conditions of alarm loops and communication chan-

nel.

• Provides arming and disarming by means of iButtons or Proximity cards.

OPERATION PRINCIPLES

9

• Transmits notifications through GSM 900/1800 cellular communication channels providing

backup operation (the second SIM card).

• Provides transmitting to five phone numbers with programming the following notification types

for every phone number:

o Contact ID (ADEMCO),
o User SMS,
o Egida-2 SMS,
o Egida-3 SMS,
o CSD,
o CSD (DC-09),
o GPRS (DC-09)
o Voice Message,
o Phone Call.

• Provides filtering messages to be transmitted based on the programmable notification filter.

• Polls Orion system devices and transmits messages from these devices:

o Under an S2000/S2000M control console or Orion Pro Workstation (Slave 1 and Slave 2

modes),

o Without a control panel (Master mode).

• Enables remote controlling by received SMS messages:

o Arming/disarming own alarm loops,
o Arming/disarming partitions (Slave 1 and Slave 2 modes),
o Requesting for partition states (Slave 1 and Slave 2 modes),
o Switching the relay outputs on/off,
o Changing phone numbers for subscribers,
o Changing Object Number.

• Provides light and sound indication of conditions of its own alarm loops, power supplies and

communication channel; this indication can be disabled.

• Provides sending test messages for link control.

• Provides automatic (and on-request) checking of the balance on the SIM cards.

• Provides protection against reading out the configuration.

• Transmits events about lost/restoring of communication channels with subscribers to the

S2000M control panel and to directions for transmission.

OPERATION MODES

The UO-4S provides operation in the following operation modes:

Standalone

This mode is intended for standalone use of the panel. In this mode the UO-4S does not

communicate data over the RS-485 interface.

• The UO-4S monitors and transmits only its own states of alarm loops, power conditions, and

communication conditions.

• Alarm loops are armed and disarmed by means of a credential, an operating alarm loop, or

remotely via GSM channel.

10

Slave 1, Slave 2

This mode is in use when the UO-4S operates as part of Orion integrated security system under an

S2000 or S2000M monitoring and control panel.

Transmitting notifications via UO-4S is supported by S2000 panels of versions 1.12+ and all

versions of S2000M panels.

To transmit notifications from an S2000/S2000M panel through the UO-4S, the
S2000/S2000M panel should be programmed with the help of PProg utility – see the
panel’s manual.

The Slave 1 operation mode is to be selected when panels S2000 or S2000M of versions 2.01-

2.03 are in use.
For control panels S2000M of versions 2.05 and higher and Orion Pro software 1.11 SP2 and

higher the operation mode Slave 2 must be selected.

The UO-4S transmits not physical numbers of zones but unique Contact ID numbers of
zones, readers, relays, and state zones of devices which are assigned to these objects in
PProg for S2000М control panels of versions 2.04 and higher or added to the UO-4S
configuration on Zones and Partitions tab for control panels of lower versions.
Numbering of Contact ID zones (relays, device states) in the control panel
configuration (in PProg.exe) must be continuous.

When the UO-4S operates in one of the slave modes all the credentials should be
enrolled in the control panel (up to control panel version 3.0.3), otherwise all messages
about arming and disarming are transmitted without a user number.

When the UO-4S operates in the Slave 1 / Slave 2 operation mode:

• The maximum number of partitions is 99;

• The maximum number of zones is 128;

• The maximum number of user credentials is 255.

Master

This mode is intended for transmitting notifications from such Orion devices as S2000-4, S2000-

KDL, Signal-20, Signal-20M, Signal-20P, Signal-10, S2000-ASPT in a system without an
S2000/S2000M control panel or Orion Pro workstation.

When the UO-4S operates in the Master operation mode:

• The maximum number of partitions is 99;

• The maximum number of zones is 128;

• The maximum number of user credentials is 255;

• There cannot be two or more UO-4S in the Master mode used in the same network. Also no

UO-4S in the Master mode can be used in one network together with a control panel.

• The XP2 jumper (see Figure 1) must be removed (open) for the Master mode. For all other

modes (Standalone, Slave 1, Slave 2) the jumper must be put on (closed).

11

When the UO-4S operates in the Master mode the numbers of all the alarm loops and
readers and the addresses of the devices must be enrolled on the Zones and Partitions
tab of UProg. Every string number of this tab is considered as the Contact ID number
of the zone, reader, or device which is described in this string. The credentials for the
connected devices must also be enrolled on the tab Credentials – Global.

If the UO-4S was connected to the PC over the RS-232 interface for programming by means of
UProg.exe then for the panel to operate in the modes Master, Slave 1 and Slave 2 the connection cable
must be disconnected from the relevant UO-4S port after completing programming.

INDICATION

The UO-4S indicates its conditions in quiescent mode as follows:

Table 1. LED Indication

Conditions Indicator Performance

COM FAULT LED: Indicates communication conditions for GSM channel and RS-485 interface

Normal communications Off
RS-485 communication fault Amber
One of the subscribers is not available; no SIM card
is present, or the SIM card is not registered on
network

Flashes with amber twice per second

POWER LED: Indicates conditions of the power supply

Norm Green
12 V Power Failure Flashes with amber twice per second
220 V Power Failure Flashes with amber once per two seconds

LP1÷LP4 LEDs: Indicate states of the relevant alarm loops

Disarmed Off
Armed Green
Intrusion/Panic/Entrance Alarm

2

Flashes with red four times per second
Fire Alarm Flashes with red twice per second
Arming Failed Flashes with green once per second

Arming Delay

Alarm loop is activated

Illuminating with green flashing with red twice per

second

Alarm loop is OK

Illuminating with green flashing with red once per two

seconds
Short/Open Circuit Failure Flashes with amber once per two seconds

GSM LED: Indicates status of the GSM communication channel

Normal communications Flashes once per four seconds
Communication lost Flashes 5-8 times every 10 seconds

Alarm Loop Indicators continue indicating alarms also within two minutes after the
relevant alarm loops are disarmed

12

Table 2. Internal Beeper

Event (Condition) Beeper Performance

Norm

Off

Alarm, Fire

Interrupted

sound

(Can be enabled

/ disabled via

UProg)

Short/Open Circuit Failure

Beeps once per second

Arming

Two beeps upon arm

ing

(

Can be enabled/disabled by means of UProg

)

Disarming

Turns off (if it was on) and then beeps once
(Can be enabled/disabled by means of UProg)

Arming Delay

Beeps once per two seconds

Within 15 seconds before the end of the delay the beeper

starts bee

ping twice per second

Arming Failed

A beep

An unknown credential is presented

A long sound

Saving configuration to the device by means of

UProg

A beep

Entering the mode of programming

credentials

Three pairs of beeps

Communication Fault*

Beeps once per two seconds

Test is run remotely from the S2000M panel

A long sound

*

- The internal sounder can be disabled for communication line faults in UProg.

Table 3. Indicators of Reader and Patrol Check Circuit

Event

(Conditions

) Indic

ator Performance

Disarmed

(All intrusion alarm loops are disarmed)

Off

Armed

(One or more intrusion alarm loops are
armed)

Illuminates when power is in norm, otherwise flashes once
per two seconds)

Alarm

(One or more alarm loops are in Intrusion
Alarm, Fire Alarm, Entrance Alarm)

Flashes four times per second

Arming Failed

(One or more alarm loops are in the Arming
Failed status)

Arming Delay

(One of the alarm loops of the Entrance type
is in the Arming Delay status)

Flashes ones per two seconds

Fa

ult

(One or more alarm loops are in the
Short/Open Circuit Failure status)

Flashes twice per second

12 V Power Failure

Flashes ones per two seconds

First touch by the credential in the quiescent
mode (see Note below)

Switches

on

for a short

time three

times and then indicates

the current state of the alarm loops associated with the
current credential (only for reader LED)

Disarming is performed after the second

touch by the credential

The indicator is switched off

Arming is performed after the second to

uch

by the credential

The indicator is switched on

Patrol Check

Patrol Check Circuit indicator flashes twice with three

flashes

Unknown credential is presented

Indicator

of

the reader flips its state for 1 s

Programming mode

The indicator is switched of

f

Master Key Programming mode

The reader indicator is on

Note: After a single touch by the credential the indicator of the reader within 30 seconds indicates the status of a
group of alarm loops associated with this credential. Arming and disarming is performed after a second touch of the
reader by the same credential within 30 seconds.

13

The parameter Disable Device Indication in UProg provides disabling of almost all UO-4S
indication except for the GSM indicator. If this parameter is set on then the panel regardless of its
operation mode doesn’t indicate by sound or by light conditions of its own alarm loops, communication
conditions, power conditions, and reading iButtons. Only GSM indicator is active. The parameter has
not an effect on reader indication.

ALARM LOOPS

The main configuration parameter of an alarm loop which defines how the alarm loop will be
monitored and what kind of initiating devices can be brought into the alarm loop is Loop Type:

• Fire: A loop of the Fire type is always armed. If a fire detector in the alarm loop kicks in then a

Fire Alarm notification is generated. In case of a short or open circuit failure in the alarm loop a
Short Circuit or Open Circuit notification is generated respectively. On restoring the alarm loop an
Armed notification is generated. For a fire alarm loop the parameter Auto Arming After Failures is

always applied.

• Intrusion: The alarm loop can be armed and disarmed. If the alarm loop is armed then on activation

of this one (in case of short or open circuit failure) an Intrusion Alarm notification is generated
immediately.

• Panic: The alarm loop is permanently armed. If the alarm loop is activated (a short/open circuit

failure has occurred) a Panic Alarm notification is generated.

• Entrance: The intrusion alarm loop which is armed and disarmed with entrance and exit delay.

• Operating: A short circuit failure of this alarm loop results in disarming (an open circuit failure

results in arming) of intrusion and entrance alarm loops linked with this loop. Only one alarm loop
from the five ones (including LP0) can be of Operating loop type.

• Patrol Check Circuit: In case of a short circuit in this loop a Patrol Check notification is

generated (This alarm loop type can be given only for LP0).

• Phone Call: The short circuit in the loop results in a phone call.

Auto Arming:

The intrusion types of alarm loops (Intrusion, Entrance, Panic) provide arming the alarm loops
after being in alarm and after failures automatically. A procedure of auto arming is performed on expire
of a delay programmed in the UO-4S configuration. To reset the status of a fire alarm loop after activa­tion also the parameter of auto arming after alarms should be set on.

Protecting Common Areas

To protect common areas, the alarm loops can be combined into an operating group:

• All the operating alarm loops are armed -> the operated alarm loops are armed

• If at least one of operating alarm loops is disarmed -> the operated alarm loops are disarmed

Table 4 shows how resistance values of the alarm loops match their states for alarm loops of
various types.

14

Table 4

Loop Type

Loop State Depending on the Loop Resistance

OK Activated Open Failure Short Failure

Fire

2÷14 k

17 k÷50 k

500 Ω÷1,6 k

>50 k

<200 Ω

Intrusion,
Panic, Entrance

2÷14 k

<1.6 k

>17 k

------------ ----------------

For the purpose of protection against sabotage, after the intrusion alarm loops are
armed they are monitored for changes their resistance with time. If the alarm loop re­sistance jumps more than 10% then the alarm loop is considered to be activated.

RELAY CONTROL

The UO-4S supports eight tactics of controlling its relays (see Table 5). For all the tactics apart

from Remote Control and Communication Failure operation of a relay depends on the selected
control tactics and states of the alarm loops associated with this relay. For all the tactics except for
Lamp, Communication Failure, and Switch Off upon Arming* a time in the range of 1 to 254 seconds
must be defined for which the relay will be switched on or the relay will be operated permanently until
the state of the related inputs (alarm loops) changes; the Lamp tactics regardless of the given time is
always applied until input’s state changes. For all the tactics of control excluding Remote Control it is
necessary to tick the alarm loops associated with this relay.

Table 5. Relay Control Tactics

Tactics «Lamp»*

All the alarm loops are disarmed Off
There is an alarm loop armed On
Fire Alarm On/Off with a period of 0.25 s
Intrusion Alarm
Entrance Alarm
Arming Failed

On/Off with a period of 0.5 s

Loop open circuit failure
Loop short circuit failure

On/Off (0.25 s on, 1.75 s off)

Tactics «Confirmation»

All the alarm loops are disarmed Off
Waiting for a confirmation On/Off with a period of 2 s
A confirmation is received On
Fire Alarm On/Off with a period of 0.25 s
Intrusion Alarm
Entrance Alarm
Arming Failed

On/Off with a period of 0.5 s

Loop open/short circuit failure On/Off (0.25 s on, 1.75 s off)

Tactics «Siren»

The loop(s) in Fire Alarm On/Off (1.5 s on, 0.5 s off)
The loop(s) in Alarm On
Other states Off

Tactics «Lock Control»

A short circuit of the disarmed alarm loop

On,
after opening the alarm loop the relay is turned off in 4s

Disarming of the alarm loop(s) The relay is turned on for 4 s

15

Table 5 (continued)

Tactics «Alarm Output» **

All the alarm loops are armed On
Otherwise Off

Tactics «Switch Off upon Arming»***

A command to arm the alarm loop is given The relay is turned off for a time
Otherwise The relay is turned on

Tactics «Remote Control»

An SMS-command to turn the relay on has
been received

The relay is turned on for a given time; if no time is given

then the relay is on steady
An SMS-command to turn the relay off has
been received

The relay is turned off

Tactics «Communication Failure»****

Normal communication with subscribers Off
Loss of communication at least with one
subscriber

On

* When the tactics «Lamp» is used with fire and panic alarm loops the relay is turned off when the alarm

loop is OK because fire and panic alarm loops are always armed.

** Tactics «Alarm Output» doesn’t operate with fire alarm loops, i.e. the relay changes its state neither in

case of a fire nor in case of an open/short circuit failure of the alarm loops.

*** The time for which the relay will be turned off can be set in the limits of 1 to 80 conventional units

provided that one conventional unit of the parameters is equal to 0.125 s. For example, in order to give
time for the relay to be turned off to 5 seconds the value of 40 should be entered (for a fire alarm loop the
relay can be turns off only on being armed by iButton from such state as Disarmed or Fire Alarm
credential to perform power-on reset for the detector).

**** Tactics «Communication Failure» may not work is the subscriber uses Who Called service of similar.

Also the tactics is not operable in case of using SMS-protocols.

For tactics «Switch Off upon Arming» and «Lock Control» the relay can be linked only
with a single alarm loop.

CREDENTIAL PROGRAMMING MODE

The UO-4S can operate partitions by means of credentials. The panel can be programmed for
using credentials by means of UProg or immediately in the mode of programming credentials. To switch
the UO-4S to the credential programming mode, the Master Key should be used.

In the process of programming the Master Key all previously saved credential data are
cleared.

The Master Key is not designed for arming and disarming.

Programming the Master Key:

1. Disarm all alarm loops assigned with the Intrusion and Entrance types.

2. Power off the UO-4S.

3. Use a piece of wire to couple the contacts of the UO-4S reader and keep the contacts coupled.

4. Power up the UO-4S.

5. Wait until the panel issues the Master Key Programming signal (two short double beeps and

then one long sound).

6. Open the contacts of the reader of the UO-4S and then quickly, within no more than 10

seconds briefly touch the UO-4S reader by the iButton. The panel beeper issues a beep. It
means that the Master Key is written to the UO-4S memory.

16

7. Quitting the mode of programming the Master Key is performed by short closing the reader

contacts for 4 seconds or automatically in 30 seconds after completing configuring operation.
In this case the panel issues one beep and then one long sound signal. Quitting can also be
performed by shutting the power off.

Programming credentials for arming and disarming alarm loops without using a PC:

1. Disarm all the alarm loops with the types Intrusion and Entrance.

2. Enter the mode of programming credentials by touching the UO-4S reader by the Master Key;

the UO-4S shall issue the signal of proceeding to the programming mode (three pairs of
double beeps).

3. Briefly touch the UO-4S reader by another iButton. The iButton code shall be entitled in the

UO-4S memory and the beeper beeps twice.

4. Light indicators LP1÷LP4 show the number of programmed credential in binary code (see

Table 6) and then after two seconds they show the states of the related alarm loops.

Notes:
– If the credential code has already been in the panel memory then the beeper issues a short

Confirmation sound.

– If the credential memory is full (16 credentials has already been enrolled) then the beeper

issues a long Error signal.

5. Define the match between the credential and the alarm loop(s) by brief closing of the relevant

alarm loop. If the LED related to the alarm loop illuminates it means that the alarm loop can be
operated by this credential.

6. To confirm programming, briefly touch the UO-4S readers by the same credential. The credential

authorized to arm and disarm will be saved in the device memory.

7. To program the panel for using other credentials, repeat steps 3–5.

8. To quit the mode of programming credentials, close the reader terminals for 4 seconds, or the

panel quits this mode automatically in 30 seconds after last operation. The beeper beeps once.
Quitting can also be performed by shutting the power off.

Table 6. Indicating User Number by Alarm Loop LEDs

# LP1 LP2 LP3 LP4 # LP1 LP2 LP3 LP4

1

9

2

10

3

11

4

12

5

13

6

14

7

15

8

Deleting Arming / Disarming Credentials

1. Disarm all the Entrance and Intrusion alarm loops.

2. Enter the mode of programming credentials by touching the UO-4S reader by the Master Key. The

panel shall issue the signal of proceeding to the programming mode (three pairs of double beeps).

17

3. Holding the Master Key touched to the reader press the tamper switch (see Figure 1) down for a

short time (no longer than 0.5 s) and then remove the Master Key. POWER LED shall flicker
periodically (two times per second with pauses of 1 second) indicating the mode of deleting
credentials.

4. By short presses on the tamper switch select the number of the credential. Indicators LP1÷LP4

shall show the number of the credential.

5. Press the tamper switch and hold it pressed for 5-8 seconds. When the credential descriptor is

deleted from the panel memory the beeper will issue two beeps and then one long sound. If there
is no credential with such number in the panel memory then the panel issues the Error signal
(single long sound).

6. To delete another credential descriptor, repeat the procedure starting with the step 4.

7. To quit the mode of programming credentials, close the reader terminals for 4 seconds, or the

panel quits this mode automatically in 30 seconds after last operation. The beeper beeps once.
Quitting can also be performed by shutting the power off.

ARMING AND DISARMING BY MEANS OF DALLAS IBUTTONS

To arm and disarm an alarm loop or a partition by means of an iButton, a double touch tactics is
used.

First Touch

Within 30 s after the first touch the indicator of iButton reader indicates status of the alarm loops
or partitions associated with this credential (см. Table 3. Indicators of Reader and Patrol Check Cir-
cuit).

Second Touch

The second touch should be performed within no longer than 30 s after the first touch.

Credential with Authorities to Arm/Disarm

• If all the alarm loops associated with the credential are disarmed or in the Arming Failed state then a

process of arming is started.

• If at least one alarm loop associated with the credential is armed or in the Alarm state then a process

of disarming is started (a process of arming will be started upon next touching).

Credential with Authority to Arm

• If at least one alarm loop associated with the credential is in the state Disarmed, Arming Failed,

Alarm then a process of arming is started.

Credential with Authority to Disarm

• If at least one alarm loop associated with this credential is in such state as Alarm, Arming Failed,

Armed then the process of disarming will be started.

Fire and panic alarm loops are always armed, so the rules mentioned above are not applicable to
them.

18

CONTROLLING UO-4S REMOTELY BY SMS

To control the UO-4S remotely it is necessary to send an SMS with a relevant command to the

UO-4S phone number (the phone number of the currently active SIM card) – see Table 7.

Table 7. Remote Control Commands

Commands SMS Messages

Request for Armed Loops

The response will be one of the following:

– If there are armed alarm loops: S,S Armed
– If no alarm loop is armed: Disarmed

PXXXXXq

Request for Partition Status

Maximum 8 partitions in a single request

PXXXXXqpP,P

Arm
(to arm the specified local alarm loops of the UO-4S)

PXXXXXaSS…

Disarm
(to disarm the specified local alarm loops of the UO-4S)

PXXXXXdSS…

Arm Partition

(only for Slave 1 / Slave 2 modes)

P

XXXXXapC…

Disarm Partition

(only for Slave 1 / Slave 2 modes)

P

XXXXXdpC…

Activate

Relay

(to switch the relay on for a time, to switch the relay off)

Only a relay of the Remote Control type can be activated remotely

P

XXXXXrNYtZ

Confirmation

(the response from a central monitoring station for an arming SMS)

PXXXXXk

Set Time

(if necessary to correct the time)

P

XXXXXthhmm

Set Time and Date

PXXXXXthhmmdDDMM

Set Object Number

PXXXXXnIIII

Check Balance

(to receive the status of the balance on the active SIM card of the

UO-4S)

PXXXXXm <carrier’s code>

Check Balance

(to receive the status of the balance on the specified SIM card of the

UO-4S)

PXXXXXbQ <carrier’s code>

Change Phone Number

(to change the specified phone number)

PXXXXXсnK<phone number>

Change Phone Number

(to change the own phone number)

PXXXXXс<phone number>

Where:

• XXXXX stands for a five-digit user’s password

• P stands for a partition number

• S stands for a number of an alarm loop (1 to 4)

• C stands for a partition number (1-99)

• Y can take a value “1” for “switch on” or “0” for “switch off”

• N stands for a relay number (1-3)

• Q stands for a sequential number of a SIM card (1-2)

• K stands for a subscriber sequential number (1-5)

• IIII stands for an object number (4 digits)

• Z stands for a time in seconds. The maximum value is 255 (in no time is defined or the time is equal to

zero then activation time is not limited)

• P, a, m, d, q, r, k, t, c, b, n are the characters typed from the keypad

• hhmm means the hours and minutes while DDMM designates the day and the month

• <carrier’s code> is the code of the carrier to check the account balance, for example *100# or *102#, it

should be specified for a particular carrier in a particular region, for example P12345m*100#. The bal-

19

ance can be checked among others also for post-paid cards (in this case and answer can be received in
two parts namely as a USSD message about receiving a request and an SMS with the balance status).

If no response has been received for account balance requests then you need to change SMS
notification service to USSD.

Examples of the commands:

P12345a14 is the command to arm the alarm loops 1 and 4 of the UO-4S, the user password is 12345
P34563d134 is the command to disarm the alarm loops 1 and 3 of the UO-4S, the user password is 34563
P12345ap12 is the command to arm the 12th partition;
P45321r11t10 is the command to switch the relay 1 on for 10 seconds, the user password is 45321
P45321r10t0 is the command to switch the 1st relay off, the user password is 45321
P12345b2*100# is the command to request the balance on the 2nd SIM card of the MTС carrier
P12345n1234 is the command to set the object number
P12345t1345d1304 is the command to set the time and date (the 13th of April, 13:45)
P12345cn3+123456789 is the command to change the phone number of the 3rd subscriber for the number

[phone]
P12345cn3123456789 is the command to change the phone number of the 3rd subscriber for the number
123456789

P12345c123456789 is the command to change the own phone number for the number 123456789
P12345qp12,34,56,78 is the command to request for status of the partitions 12, 34, 56, 78

Table 8. Responses for Control Commands

Responses In Cyrillic Characters In Latin Characters

Relay N Activated

Реле включено N
Реле выкл. N

Relay is on
Relay is off

Time Set Уст. времени Time set
Time and Date Set Уст. времени Time set

Object Number Set Номер изменен Set number
Phone Number Changed Замена номера Phone set
Confirmation Квитирование Receipt

Wrong Password Неверный код Wrong password
Command Failed (an unknown
phone number, a parameter error
of the command in the SMS)

Нет доступа No access

Relay Control Denied Нет доступа No access

* – A response to a request for partition status comes in the Egida-3 SMS protocol (for example,

F99I0255S241P10) and is intended for operation in Egida-3 Central Monitoring Station software)

** – The response is generated in Latin symbols if extended character set is not in use by the panel (that is

there are no Cyrillic characters in parameter and event descriptions)

INSPECTING PANEL OPERATION IN THE TEST MODE

In the Test mode the panel inspects operation of its light indicators and beeper. The panel can
be switched to the Test mode only from the menu of the control panel and only for S2000M of
versions 3.0 and higher (for more information please refer to S2000M User’s Manual).

After the panel has entered the test mode:

20

– The panel beeps;
– The indicators COM FAULT, POWER, LP1 - LP4

1. Illuminate with amber, then

2. Illuminate with green, then

3. Illuminate with red, then

4. One-by-one turns on with green, and finally

5. One-by-one turns on with red.

After the test has been completed the panel automatically exits the self-diagnostic mode and

returns to quiescent mode.

TRANSMITTING NOTIFICATIONS

Notification Formats

The UO-4S can transmit notifications to five phone numbers and for each number a notification

format can be programmed individually:

• Contact ID (ADEMCO) – Appendix A;

• User SMS – Appendix B;

• Egida-2 SMS – Appendix C;

• Egida-3 SMS – Appendix D;

• Voice Message – Appendix E;

• Phone Call;

• CSD;

• CSD (DC-09).

Contact ID (ADEMCO)

This notification type is used to transmit events via voice channels to central monitoring stations.
The list and format of notifications is shown in Appendix A. An UOP-3 GSM can be used as a receiving
device.

User SMS

The panel supports transmitting user messages both in Cyrillic and Latin characters and provides
editing them by means of UProg (using Latin character provides more cost-effective way to send SMS).

Depending on the mode the device operates in the data transmitted in user SMS vary in follow
aspects:

Standalone Mode: messages are sent with specifying alarm loop numbers:

Object Name, DD-MM (optionally) HH:MM, Event, LP, Zone Description (optionally)
Object Name, DD-MM (optionally) HH:MM, Event, User Number, User Description (optionally)

Slave 1, Slave 2, Master Mode: messages are sent with specifying numbers of partitions and
zones:

Object Name, DD-MM (optionally) HH:MM, Event, Partition Number, Zone Number, Zone Description (optional)
Object Name, DD-MM (optionally) HH:MM, Event, Partition Number, User Number, User Description (optional)

The list of messages is shown in Appendix B.

21

SMS (Egida-2), SMS (Egida-3)

Transmitting SMS to a central monitoring station with Egida rev.02 or Egida rev.03 software
respectively. Notification formats are shown in Appendix C and Appendix D. Receivers can be an
UOP-3 GSM and a GSM modem. Description of SMS for the protocols Egida-2 and Egida-3 is not
available for editing by user.

Voice Messages

All voice messages begin with the phrase “Attention, the message from the object number…”
followed by the code of the object and the text of the message itself. The panel cannot synthesize object
descriptions by voice, so the messages contain only the numbers of partitions, zones, and users
(credentials).

A voice message for a current direction is considered to be delivered if it has been heard in
full including the given number of message repeats. Otherwise the UO-4S will try to
establish communication once more and to transmit the notification so many times as
defined for the voice message notifications.*

* If the Who Called option (or similar) is activated for the subscriber then the number will not be

called repeatedly.

Phone Call

For this notification type the UO-4S dials to the subscriber and hangs up; this type of notification

is used to inform the subscriber that an event has happened without describing the event.

CSD (DС-05)/CSD(DC-09)

If this type of notifications is selected then data are transmitted via GSM network over the fax­data channel in digital form with the rate of 9.6 Kbit/s. A receiver can be UOP3-GSM or GSM modem
for CSD (DС09).

Many carriers can transmit and receive data via CSD only after special connecting of this
service.

GPRS (DC09)

Notifications are transmitted using GPRS in the protocol «DC-09» to a specified IP address and
port. Data can be received on a PC immediately (without panels) provided that Egida-3 Central
Monitoring Station software or other software supporting this protocol is installed on the PC.

If the transmission over GPRS is enabled it is of the highest priority in its group. While operating
via GPRS, by default data are encrypted using the default key (encryption keys are adjusted in
UProg.exe and Egida-3) provided that encryption can be disabled when necessary.

Filtering

To minimize data to be transmitted and to provide receiving only the required information, an
event filter can be adjusted for every subscriber number. The filter criteria are alarm loop numbers (for
the standalone mode) and types of event.

Grouping

To provide redundancy, phone numbers can be combined into groups. If a group number is the
same for all phone numbers then the panel will transmit notifications only to one number from the
group, namely the first number which the panel has reached. If group numbers are different then the
UO-4S will consistently transmit notifications for all phone numbers assigned with different group
numbers.

22

Testing Communication Channel

Test notifications are intended for testing current operability of the communication channel and
can be applied for phone 1 and phone 2. A Test notification can be either SMS (a transmission period in
hours should be specified) or a phone call (a call period can be set in minutes or in hours or a time for
calls once or twice a day should be specified).

Test notifications must comply with notification type selected for the relevant subscriber.
That is, if User SMS are in use then Test notifications should also be SMS while if voice
calls, ID Contact, and CSD are in use then Test notifications should be phone calls.*
Phone calls are also permitted to be used as Test notifications for operation with Egida-3
Central Monitoring Station using Egida-3 SMS notification type.

* If the Who Called (or similar) service is active for the subscriber then the panel will consider a
test call as successful and this can affect the results of testing the quality of communication channel with
the relevant subscriber.

Apart from the option “Phone call at a specified time”, Test Transmission Period starts to be

counted since the moment of last transmission of any notification to the relevant phone.

In the mode of phone calls on receiving a Test notification a subscriber takes the call. This con­firms for the UO-4S that the notification is received and the panel releases the phone line. The call time

doesn’t exceed two seconds and as a rule is not charged by the carrier.

If at the time of sending a test notification the subscriber is not available or no answer is received
from the server while operating via GPRS the panel generates the event of communication loss for this
channel and transmits this event to other subscribers and to the S2000M control panel (while operating
in a slave mode).

23

MOUNTING

MOUNTING THE DEVICE

Figure 2 shows the appearance and overall and mounting dimensions of the UO-4S panel. The
panel is to be mounted on walls or other structures in the premises at places protected against atmospheric
fallouts, mechanical damage, and unauthorized access.

Wiring of connecting lines is to be carried out as shown in Figure 5 (“UO-4S Connection
Diagram”).

Figure 2. Overall and Mounting Dimensions

The UO-4C should be mounted in line with the Russian regulatory document РД.78.145-92
“Rules of Work Arrangement and Commissioning. Installations of intrusion and fire alarm systems”.
The panel should be attached at a height where it is convenient to operate and maintain the device.

24

Mounting on a Wall

1. Please ensure that the wall the device is to be mounted on

is solid, flat, clean, and dry.

2. Mark places for three mounting holes on the wall (for two

upper holes and one of the bottom ones) in accordance
with the mounting pattern for the panel.

3. Drill the holes, insert wall plugs into them and screw

provided woodscrews into the two upper holes so that the
distance between a screw head and the wall is about
7 mm.

4. Remove the front cover from the panel as shown in

Figure 3).

5. Hang the device on the two screws. Screw the next

woodscrew into the bottom mounting hole and tighten it
up until bumping to fasten the device to the wall.

Figure 3. How to Remove the Cover

Mounting on a DIN Rail

1. Select the mounting location where free access to the tapping screw at the upper end of the device

front cover is provided.

2. Install the device on the DIN rail as shown in Figure 4.

3. Remove the device front cover as shown in Figure 3.

Figure 4. Mounting the Panel on a DIN Rail

Connection

Mounting of connecting and communication lines is carried out in accordance with Figure 5

(“UO-4S Connection Diagram”).

Turn the case until

clips onto the rail

2

Place the hooks of

the panel base un

der

the lower edge of the

DIN rail

Нажмите больши-

ми пальцами на

верхний торец

крышки

Сдвиньте

крышку

вперёд

Выкрутите винт

крепления крышки

1

3

Slide the

cover

forward

Unscrew the screw

fixing the cover

Push the top end
of the front cover

down by your

thumbs

25

RS-485 Interface Bus

When the UO-4S is used as part of an Orion integrated security system:

1. Connect the terminals RS-485A and RS-485B to the lines A and B of the RS-485 interface bus

respectively.

2. Connect the “0 В” circuit of the panel to the similar circuit of the preceding and the subsequent

devices on the RS-485 trunk (if the devices are powered by the same power supply this doesn’t have to be
done).

3. If the panel is neither the last nor the first device on the RS-485 interface bus then remove the

XT3 jumper which is situated closely to A and B contacts on the panel PCB.

Figure 5. UO-4S Connection Diagram

Figure 6. Connecting Alarm Loops and Operating Loop

26

Figure 7. Connecting Readers

Inserting SIM Cards

SIM cards are to be installed into the panel after the panel has been programmed.

The primary SIM card is to be inserted into the lower slot (which is closer to the panel’s PCB),

and the backup SIM card is to be inserted into the upper slot (under the metal plate).

Closing Cover

Figure 8. How to Close the Cover

Four-wire detectors (with external powering) should be used as fire detectors. After
receiving a Fire event it is necessary to reset power of the relevant detector; for
doing so one of the panel relay outputs can be used (the tactics «Switch Off upon
Arming»).

Prior to inserting SIM cards into the UO-4S it is preferable to turn off asking PIN
codes for them by means of a cell phone. If it is required to use SIM card protected by
asking PIN then digit PINs of the primary and backup SIM cards should be specified in
SIM card settings in UProg (tab “Device”).

Insert and tighten

the screw supplied

Guide the projections of the

cover behind the base hooks

Turn a cover until a

specific click is heard

27

PROGRAMMING

PROGRAMMING UO-4S

The UO-4S parameters are configured with the help of UProg (of version 4.1.0.51 and higher).

While programming the UO-4S it is recommended to use the last version of UProg
which can be downloaded from

https://bolid.ru/files/373/566/InstallUProg_411.zip
https://bolid.ru/support/download/?groupsID=3&tagsID=0&q=Uprog

Configuring

To configure the UO-4S parameters, connect the panel to a power supply and to a PC with

UProg.exe Device Configuration Tool installed via the adapter cable provided or via one of the Bolid
manufactured interface converters (PI-GR, S2000-PI, S2000-USB, or USB-RS-485).

Figure 9. Connecting the UO-4S to a PC via the Adapter Cable

If the UO-4S is connected to the PC over the RS-232 cable for programming then for the panel
can operate in the modes Master, Slave 1 and Slave 2 the connection cable must be disconnected from
the relevant UO-4S port after configuring.

Figure 10. Connecting the UO-4S to a PC via an Interface Converter

28

Please remove SIM-cards from the UO-4S while programming the panel parameters. The
XP2 jumper (see Figure 5) must be closed during programming.

RUNNING CONFIGURATION TOOL

Run UProg.

Load configuration from the device memory:
Menu Device

→→→→

Read Device Configuration

The window for searching devices connected to the computer appears on the PC display. In the
Serial Port field enter the logical number of the COM port the UO-4S is connected to. Then the Search
Devices procedure is started.

Figure 11

On completing the search procedure UProg displays the list of all the devices connected to the
selected COM port, with address and version numbers being specified for each device. Select the device
that is to be programmed.

Change Panel Address

The panel’s RS-485 network address can be changed by means of the UProg menu command

Device

→→→→

Change Device Address.

In a slave mode the UO-4S address is recommended to be set to 127 while addresses of
the devices connected to the UO-4S should be set to values from 1 and higher.

Saving Configuration

To write configuration to the UO-4S memory, please click the Write Configuration to Device
button and exit the program. The UO-4S shall confirm writing the new configuration by sounding of the
built-in beeper.

29

Tab «Device»

Figure 12. UProg for UO-4S

Object

• Object number is composed of four digits 1 to 9.

• Object Name can comprise maximum 64 Latin characters including spaces or 32 characters

including spaces if Cyrillic characters are in use (used in case of transmitting user SMS).

• Entry Delay is the delay for alarm loop’s proceeding from an Entrance Alarm state to the Intrusion

Alarm state.

• Exit Delay is the delay of arming an alarm loop.

Internal Alarm

• Alarm Time is the time is seconds for which the internal beeper sounds upon receiving such alarms

as Intrusion Alarm, Fire Alarm, Short Circuit, and Open Circuit from the alarm loops linked to the
beeper.

• Arming/Disarming: If this parameter is set on then the panel beeper will sound when alarm loops

of the panel are armed and disarmed.

• Communication Fault: If this parameter is set on then the panel beeper will sound in case of loss

of communication in specified channel.

30

Device

• Operation Mode: This parameter provides selecting the mode of panel operation.

The required operation mode must be obligatory selected prior to proceeding to set­ting parameters of credentials, zones, and partitions.

• Use Backup SIM Card: If a second (backup) SIM card is installed into the UO-4S then when a

notification cannot be transmitted over the primary notification channel (poor communication
quality, zero or negative account balance) this one will be transmitted over the backup
communication channel (both cards are equivalent and the panel returns to operation with the
primary card only when transmitting data using the backup card fails or after power-on reset).

• Extended Character Set: The parameter informs that notifications are transmitted using Unicode

extended character set (the UO-4S starts transmitting SMS in Unicode if the object name or User
SMS contain Cyrillic characters).

• Transmit SMS with Data: If this parameter is set on then the UO-4S transmits User SMS with the

data, not only with the time.

• Configuration Read Protection: This parameter can be set on / off when a password against

unauthorized programming of the panel is given. If the parameter is set on then in case of an
attempt to read configuration after 30 seconds since last programming UProg will ask the password.

Figure 13. The Dialog Window to Enter Configuration Password

Configuration Password can be discarded upon panel’s entering the programming
mode without presenting Master Key (on powering the panel up with closed terminals
of the reader). Then panel’s configuration should be read and password should be
changed or discarded.

• Disable Panel Indication: If this parameter is set on then the panel indicates events neither by

lighting nor by sounding except for GSM LED and reader indication. Indication can be suppressed
only when the tamper switch of the panel is closed.

31

Relay Outputs

To program relays it is necessary to select Relay Type, to give Activation Time during which
every relay is activated in accordance with the defined control tactics, and to select the alarm loops
linked with every relay.

The parameter Activation Time for the relay tactics Switch Off upon Arming can be set to a
value which corresponds to a time in the range of 1 to 10 seconds, with one unit of the parameter being
equal to 0.125 s.

• Activation Time = 0 – The relay will not be activated.

• Activation Time = 255 – The relay will operate in accordance with the selected tactics until

linked inputs change their state.

The Activation Time parameter is not applicable to a relay if the relay is assigned with one
of such tactics as Lamp, Communication Failure, and Remote Control. Such relay always
operates in accordance with given tactics until the linked inputs change their state.

When the relay control tactics «Switch Off upon Arming» and «Lock Control» are in use
the relay can be linked only with a single alarm loop.

SIM Card Settings

While using SIM cards it is recommended previously to turn their PIN codes off. However, if it
is required to work with cards for which PIN codes are asked then it is necessary to specify these codes
in the relevant fields for the primary and backup SIM cards.

If it is necessary to ask the balance automatically then the balance request codes should
be typed in the relevant fields of SIM1/SIM2 and the relevant period for automatic
checking in days should be selected.

To turn a PIN off in the device settings switch the panel to the programming mode
without presenting the Master Key (power the panel up closing the reader terminals)

32

Tab «Alarm Loops»

Figure 14. Alarm Loops Tab

Auto Arming Delay: This parameter means a time in which an alarm loop will be armed when it

has been repaired after being in alarm. The value can be set in the range of 1 to 255.

For an alarm loop of the Entrance type Auto Arming Delay must exceed Entry Delay.

• LP Type: Selecting the type of an alarm loop for LP0-LP4.

• LP0 Type: The way to use the input “0В-ТШ” on the device PCB, namely Patrol Check Circuit,

Operating Loop, or Phone Call. If a Patrol Check button is used then select the type Patrol Check
Circuit; if a common alarm loop is used which operates other UO-4S inputs then select Operating
Loop; and if activation of zeroth alarm loop should lead in a phone call to a dial-up phone number
then select the Phone Call type.

• Auto Arming After Alarms/Failures: Intrusion types of the alarm loops (Intrusion, Entrance,

Panic) support automatic arming them after being in alarms or in the Arming Failed status. An auto
arming procedure is started on expire of a programmable delay defined in configuration; the
parameters of auto arming are defined for every internal alarm loop individually.

The parameter Auto Arming After Failures is always applied for fire alarm loops (re­gardless of whether this flag is set on or off).

• Linked to Relay…: Tick the alarm loops linked with the relevant relay.

• Linked to Beeper: If the parameter is set on then activation of this alarm loop causes the panel to

indicate this event by sounding.

• Group Arming / Disarming: Operated alarm loops are armed upon arming of all operating alarm

loops. Operated alarm loops are disarmed upon disarming of any operating alarm loop. Both
operated and operating alarm loops must be marked with a plus character.

33

Tab «Telephones»

Figure 15. Telephones Tab

Voice Message Transmission Attempts

A communication attempt can fail due to subscriber on the receiving side being busy or poor link
quality or a communication failure. After a specified number of attempts the panel proceeds to a next
subscriber and enter the communication fault mode for the current subscriber. The parameter is
applicable to voice messages and transmission in the Contact ID protocol.

The number of attempts should not be equal to zero, it is advised to be set to 2 – 3 attempts or
more.

Max Number of Notifications per DTMF Connection

The maximum number of notifications per a single Phone Call used while operating with the
Contact ID protocol. It is advised to set this value to 5-8 notifications (to be corrected experimentally).

SMS Transmission Attempts

The number of attempts to transmit an SMS after which the panel switches to a next subscriber
and enter the communication fault mode for the current subscriber. It is recommended to specify 2-3

attempts or more.

Voice Message Repeats

It is advised to set at least one and no more than three times the voice messages will be repeated
(if the number of repeats is set to zero then voice messages will be spoken once). On repeating the
object number is not spoken.

34

Listen Timeout in 10 s-Intervals (*10)

It is the time after expiry of which the panel terminates the connection established upon

activation of an alarm loop of the Phone Call type.

Phone Number

A phone number should be entered completely including the country/area code (the prefix «+»

can be used).

Password

To provide a possibility to control the panel from the cell phone, a five-digit password must be

set in this field.

To operate partitions in a slave mode, in the configuration of the control panel (in PProg.exe) the
phone number must be entered as a credential with the relevant access level to operate partitions. The
phone number should be entered in the control panel configuration along with the country and area
codes (with «8» or «7» without the «+» sign) as well as it is entered in the UO-4S itself.

Group Number

To create backup communication channels, phone numbers are combined into groups. If a
notification cannot be delivered to a first phone in the group it is transmitted to a next number. If a
notification is supposed to be sent to every phone number then the group values should be set different
for every number.

Communication Fault messages are not transmitted between the groups (directions) apart
from the GPRS channel.

Notification Type

To transmit events, one of the following notification types can be selected:

• Contact ID (ADEMCO);

• User SMS;

• Egida-2 SMS;

• Egida-3 SMS;

• Voice Message;

• Phone Call;

• CSD (DC-05/DC-09)

One phone number can be used to transmit notifications of various types to it. For doing so, the
phone number should be added twice to the panel configuration with different notification types. The
two phones are to be combined in a group, thus the second notification type will be the backup one.

Enable Remote Configuring

If this parameter is set on for a subscriber then this subscriber can remotely (by SMS commands)
change Object Number, request for the balance, change the data and time, and change its phone number.
In addition, the subscriber can remotely change also the number of another subscriber if it specifies this
number in the command (after changing the number a confirmation command from the UO-4S about
changing the number is arrived to the new number).

Send Test Notification As

Test notifications are used to check operability of communication channels and can be sent to
Phone 1 and Phone 2. A Test can be sent either as an SMS (sending period is set in hours) or as a phone
call provided that a period of calling can be set in minutes or hours or calls can be given at the set time
(once or twice a day).

35

The field Test Transmission Period can take a value ranging or from 1 to 59 if the period is set in
minutes, or from 1 to 24 if the period is set in hours or at a specified time, or from 1 to 12 when the
Twice a Day flag is set on.

Apart from the mode of phone call at a specified time the period of sending Test message is
counted starting at the moment of last transmission of any message (including response messages to the
balance request and SMS control commands) to the relevant cell phone.

In the mode of a phone call on receiving the test notification the subscriber takes a call and this is
a confirmation for the UO-4S that the notification is taken. Then the UO-4S clears the line. The call time

doesn’t exceed two seconds and as a rule is not charged by a communication operator.

If a Test notification is sent in one direction then it will not be transmitted to other
directions.
SMS-notification “Test” can be used only with SMS notification types (User SMS, Egida-2
SMS, Egida-3 SMS)

Dial-up Phone Number

This is a number of the telephone where dial-up is made when an alarm loop with the Phone Call
type is activated. This phone number must be entered in full, including the area code. When a call is
made from this number the UO-4S picks up the handset to broadcast the signal from the microphone.

Permit to Take Off the Receiver

When called from the phone number for dialing, the panel turns on the microphone and speaker
(if they are connected to the corresponding terminals) for the specified listening time in 10 seconds
intervals.

Phone Call Hold

If at the moment of translation the panel is ringed up, the panel doesn’t hang up.

36

Tab «Message Filter»

Figure 16. Message Filter

Message Filter provides adjusting a list of events and local alarm loops for which notifications

will be sent to a specified phone.

A tick in the Message Filter table means transmitting the relevant messages to the relevant phone
while a blank cell means that the events will not be transmitted. The filter is applied both to standalone
operation of the UO-4S and to cooperation of the UO-4S with Orion system devices.

Every filter can comprise several events falling under this group. The table below shows the
examples of the events falling under the filters.

The filter for alarm loops of the UO-4S (LP1 − LP4) is applicable only when the panel operates
in the Standalone or Master mode. If the UO-4S operates under the control panel the filter related to the
internal alarm loops of the UO-4S is ignored.

37

Filter Name Events

Armed Partition is armed, a leakage is repaired
Alarm Intrusion alarm, panic alarm, leakage (flood detector alarm)
Fire Fire, Fire2

Loop Failure

Alarm loop short circuit failure, alarm loop open circuit failure, fire
protection equipment failure, service required, loop configuration error,

temperature sensor fault, noise
Communications Restored Communication with the device/subscriber is restored
Communication Loss Loss of communications with a device, loss of connection with a subscriber

PL Open/Short Circuit

Polling loop short circuit failure, polling loop open circuit failure, PL

communication error, PL unstable communication
Output Circuit Failure

Output open circuit failure, output short circuit failure, actuator failure,

actuator error

Off / On

An alarm loop is disconnected, and alarm loop is connected, and output is

disabled, an output is enabled, a pump is on, a pump is off, an actuator is in

initial position, an actuator is in operation position, auto mode is off, auto

mode is on
Temperature High temperature, low temperature, normal temperature
Level High level, low level, too high level, too low level, normal level

Auxiliary Loop

Auxiliary loop alarm, auxiliary loop restored, activation of a second

auxiliary alarm loop
Batteries

Low battery, low backup battery, backup battery restored, battery failure,

battery restored, battery test error
Charger

Power supply overload, overload repaired, RIP charger failed, RIP charger

restored
Equipment

Discharge of extinguishing agent, voice announcement activated and other

events not included in the filters
Doors

A door is forced open, a door is propped open, a door is closed (after being

forced/propped open), wrong code

Tab «Credentials»

To work with credentials and their operating authorities there is an additional toolbar in the

UProg with the tools as follows.

Load credentials from a file

Write credentials to the device

Save credentials to a file

Load credentials from the
panel memory

Add a new credential descriptor

Read a credential

Delete the selected credential de­scriptor from the panel memory

Prior to enrolling credentials ensure that the Operation Mode parameter on the Device
tab is set to a proper value.

38

Enrolling Credentials by means of an iButton Reader

To enroll credential codes by means of an iButton reader, the iButton reader should be connected

to the UO-4S terminals 23, 24, and 25 (see Figure 5).

1. Load the panel configuration by means of UProg. Go to the Credentials tab. When the Cre-

dential tab has been open the device descriptors start being read from the panel memory au­tomatically.

2. Add a new credential descriptor on the Credential tab by clicking .

3. Then read the credential code . If the credential code is read successfully the panel beeps

and a unique code appears in the relevant Credential Code cell.

4. Next, define the credential rights by ticking the boxes in the cells of the alarm loops which

can be operated by the credential. Then save the credential to the panel memory by
activating the tool , «Write credentials to the device».

5. To delete a credential descriptor from the panel memory use the button .

Setting Local Credentials

Figure 17. Local Credentials

• Type: The type of the credential. The value of Type can be one of iButton (TM), Operating
Loop (OL), Telephone (T1, T2, T3, T4, T5), or PIN code (PIN).

• Credential Code: For iButtons their codes are read by means of the iButton reader and for tel-
ephones the code is entered using the keyboard (5 digits).

• Rights: Operating authorities of the credentials (Arming, Disarming, Arming / Disarming).

• LP1 – LP4: The numbers of the alarm loops which can be operated by the credentials.

39

The credential with ID 0 is the system Master Key which is used for programming user

credentials for the UO-4S without UProg and cannot be used for arming / disarming.

In the modes Slave 1 and Slave 2 all the credentials including local ones must be enrolled
in the control panel. Messages about arming and disarming the UO-4S contain ID (the
sequential number) of the user in accordance as they are numbered in the control panel
while the match between ID and the user name is defined in Global credential settings

Setting Global Credentials in the Master Mode

To transmit User ID and User Name while arming and disarming zones/partitions the Global

Credentials table is used.

Figure 18. Global Credentials, Master Mode

Global credentials can be enrolled using the reader or the keyboard (credentials of the PIN type).

In the Master mode the UO-4S cannot control the slave devices and the credentials are
enrolled only for the possibility to transmit credential ID and User Name. So, the same
credentials must be locally enrolled in the devices.

Setting Global Credentials in the Slave 1 or Slave 2 Mode

When the UO-4S operates under the control panel all the credentials including local ones must
be enrolled in the memory of the control panel as described in the control panel’s manual. In this case
the sequence number of a credential will be transmitted by the control panel as a user number (ID). The
match between ID and user names is described in the UO-4S on the tab Credential – Global.

40

Tab «Zones and Partitions»

Standalone Mode: The match between the zones and partitions is given in the UO-4S. A Zone

Number means the number of an ID Contact Zone (in the Standalone mode this tab can be not filled in).

Master Mode: The match between device addresses, zones, and partitions is described in the

UO-4S. A string number in this case is the number of the ID Contact Zone.

Slave 1 Mode: The match between device addresses, zones, and partitions is described in the

UO-4S. To receive events from the devices the UO-4S configuration must contains status zones of the
devices where the alarm loop number is specified as zero (“0”) and the number of this string will mean
the ID Contact number of the device state.

Slave 2 Mode: Numbers of zones and partitions are transmitted from the control panel; only

textual description of the zone can be added in the UO-4S. For the Slave 2 mode, assign in the control
panel configuration (using PProg.exe) the ID Contact numbers of all the zones, readers, panel status
zones, and relays which events are to be transmitted to the UO-4S. A test description of a zone in this
case is typed opposite the number of the string which matches to the zone ID Contact number in the
configuration of the control panel.

Figure 19. Zones and Partitions. Master Mode

The UO-4S doesn’t support partition descriptions so only partition numbers are specified for user

SMS.

When the UO-4S operates together with the control panel in Slave 1 or Slave 2 operation
modes, local alarm loops must be enrolled in the control panel database

41

Tab «Message Descriptors»

Figure 20. Message Descriptors

This tab is intended to edit texts of user SMS if necessary. Symbols in Latin or Cyrillic scripts
can be used. The SMS writing system can be selected from the context menu by right clicking on a text
string.

42

Tab «GPRS Settings»

Figure 21. GPRS Settings

Enable GPRS: The flag enables sending data over the GPRS channel.
For the main and backup receiver the following parameters must be set individually:

• IP Address (Static IP address of the host with Egida rev.3 Central Monitoring Station)

• Port (the number of the UDP port open for receiving messages over Internet on the host with

Egida rev.3 Central Monitoring Station)

• MasterKey (encryption key). This key is used for encrypted transmitting of events to Egida

rev.3 Central Monitoring Station. To specify a key, open the relevant dialog window by clicking the
check mark at the right part of the MasterKey field (see Figure 22). To use the default encryption key,
tick the relevant box at the right top part of the window.

Figure 22. Changing Encryption Key

43

Also your own encryption key can be generated by the program automatically using the typed
passphrase. For doing so, enter a password in Latin script into the Password field, then confirm it, and
finally save changes by clicking OK. For Egida 3 Central Monitoring Station the same password must
be entered in GPRS settings for this UO-4S to provide decoding of the notifications.

W/o Encryption: If this flag is set on then the UO-4S sends DC09 notifications without
encrypting them. (This parameter is recommended to be set on for networks with low GPRS channel

throughput and high density of events sent from the UO-4S to the CMS (Central Monitoring Station).

If backup channel is not in use then there must be all zeros in the IP Address and Port fields.

Common settings are the following:

• Connection Establishment Timeout (60 seconds is recommended)

• Response Waiting Timeout (20 seconds)

• Transmission Attempts (the minimum recommended value is 2-3 attempts)

• TEST Transmission Period (60 to 250 seconds); this time must be longer than call setup time

• Group Number (the number of the group in which GPRS-transmission is included)

Carrier settings, to be set individually for SIM1 and SIM2:

• Login (the login (account name to access GPRS service of the carrier. For every carrier its

specific login must be used, for example “mts” for the “МТС” carrier, “beeline” for the “Bee­line” carrier, and “megaphone” for the “Мегафон” carrier)

• Password (the password to access GPRS service of the carrier. For every carrier its specific

password must be entered, for example “mts” for the “МТС” carrier, “beeline” for the “Bee­line” carrier, and “megaphone” for the “Мегафон” carrier )

Access point name APN (the name of the GPRS/3G gateway for your carrier, for example
“internet.beeline.ru” for “Beeline”, “internet.mts.ru” for “МТС:, and “internet.megafone.ru” for
“Мегафон”).

44

MAINTENANCE

The UO-4S must be maintained at least annually by electricians with the third or higher electric

safety qualification level.

To maintain the panel, do the following:
a) Ensure the panel enclosure is not damaged and is mounted securely; ensure the wire terminals

are fastened properly;

b) Remove dust, debris, and corrosion from the contact connections and the panel enclosure;
c) Inspect panel operability by testing panel indication in accordance with Table 1 and panel

sounder performance in accordance with Table 2.

Table 9. Troubleshooting

Problem Possible Cause Solution

POWER LED is off when the
UO-4S is switched on

No power is applied

Check power voltage to be applied to

the UO-4S
POWER LED flashes with amber
two times per second

Input power voltage is exceeding
15 V or is below 10 V

Check the level of the supply voltage

COM FAULT LED illuminates
with amber

No communication with the devices
or the control panel over the RS-485
interface

For a slave mode check the operation

mode of the control panel. For the

Master mode check the XT2 jumper

to be open

GSM LED doesn’t illuminate

SIM card not inserted or failed Check the SIM card

SIM card is locked to ask PIN or
extra options (such as SimToolKit)
are activated for it

Turn off asking the PIN and extra

options for the SIM card by means of

a mobile phone or the carrier

COM FAULT LED pulses with
amber two times per second

•

SIM card cannot register in the

mobile network

• No connection with the subscriber

(message failed to be delivered)

• No connection with the central

station

• Wrong phone number of the SMS

center is entered

• Account balance is lower than a

minimum value

•

Make sure the SIM card is inserted

into the relevant slot

• Check the antenna or connect an

external one

• Check the signal level at the

mounting location of the UO-4S
by means of a mobile phone

• Enroll the phone number of the

SMS center into the SIM card as
described in the phone manual (use
a cell phone to setup)

• Eliminate the financial debt

POWER LED flashes with amber
once per two seconds

Mains power applied to the RIP has
failed (signal from contacts 5 and 6)

Repair mains power of the RIP

45

STORAGE, TRANSPORTATION, AND WARRANTY

STORAGE

The UO-4S in the consumer packing must be stored in line with Storage Ambients 1 of Russian

Standard ГОСТ 15150-69.

The premises where the UO-4S is stored must be free from any acid fumes, alkaline fumes and

other aggressive gases and harmful impurities which can cause corrosion.

TRANSPORTATION

The packed UO-4S should be transported by any covered vehicles in accordance with

requirements of transport organizations.

The transportation terms and conditions for the UO-4S must be the same as Storage Ambients 5

of Russian Standard ГОСТ 15150-69.

WARRANTY

The manufacturer warrants the UO-4S to conform its technical specifications if the consumer

meets the rules of transportation, storage, mounting, and operation.

The warranty period is 18 months since putting the panel into operation, but no more than 24

months since the acceptance date.

In case of difficulties in programming or operating the product, please contact Technical Support

by calling [phone] (multichannel) or by emailing [e-mail].

46

APPENDICES

APPENDIX A. CONTACT ID PROTOCOL

Notification

Contact ID Protocol Messages

Serial

Number

4 symbols

ID

Qualifier

Event
Code

Partition
Number

2 sym-

bols

Zone Number (Z),

User ID

3 symbols

Disarmed

XXXX 18 1 401 Р User

Armed

XXXX 18 3 401 Р User

Arming Failed

XXXX 18 1 454 Р Z

Guessing

XXXX 18 1 406 P Z

Patrol Check

XXXX 18 1 999 P Z

Fire Loop Failure

XXXX 18 1 373 Р Z

Fire Alarm

XXXX 18 1 110 Р Z

Fire Prealarm (Orion)

XXXX 18 1 118 Р Z

Intrusion Alarm

XXXX 18 1 132 Р Z

Panic Alarm

XXXX 18 1 122 Р Z

Entrance Alarm

XXXX 18 1 134 Р Z

Alarm Loop Open Circuit Failure

XXXX 18 1 371 Р Z

Alarm Loop Short Circuit Failure

XXXX 18 1 372 Р Z

Loop Repaired After Open Failure

XXXX 18 3 371 Р Z

Loop Repaired After Short Failure

XXXX 18 3 372 Р Z

Power Failed (power voltage is below

11 V or above 15 V)

XXXX 18 1 302 Р Z

Power Restored

XXXX 18 3 302 Р Z

AC Power Failed

(longer than 20 seconds)

XXXX 18 1 301 Р Z

AC Power Restored
(longer than 20 seconds)

XXXX 18 3 301 Р Z

Tamper Alarm

XXXX 18 1 383 Р Z

Tamper Restored

XXXX 18 3 383 Р Z

Device Restart

XXXX 18 1 305 Р Z

Polling Loop Failure (Orion)

XXXX 18 1 331 Р Z

Polling Loop Restored (Orion)

XXXX 18 3 331 Р Z

Output Circuit Failure (Orion)

XXXX 18 1 320 Р Z

Output Circuit Restored (Orion)

XXXX 18 3 320 Р Z

Device Disconnected (Orion)

XXXX 18 1 350 Р Z

Device Connected (Orion)

XXXX 18 3 350 Р Z

Starting Programming Mode

XXXX 18 1 627 P Z

PL Short Circuit (Orion)

XXXX 18 1 332 Р Z

Disabled (Orion)

XXXX 18 1 382 Р Z

Enabled (Orion)

XXXX 18 3 382 Р Z

High Temperature (Orion)

XXXX 18 1 158 Р Z

Low Temperature (Orion)

XXXX 18 1 159 Р Z

High Level (Orion)

XXXX 18 1 166 Р Z

Low Level (Orion)

XXXX 18 1 167 Р Z

Two High Level (Orion)

XXXX 18 1 168 Р Z

Too Low Level (Orion)

XXXX 18 1 169 Р Z

Normal Level (Orion)

XXXX 18 3 166 Р Z

47

Notification

Contact ID Protocol Messages

Serial

Number

4 symbols

ID

Qualifier

Event
Code

Partition
Number

2 sym-

bols

Zone Number (Z),

User ID

3 symbols

Auxiliary Loop Alarm (Orion)

XXXX 18 1 150 Р Z

Auxiliary Loop Restored (Orion)

XXXX 18 3 150 Р Z

Low Battery (Orion)

XXXX 18 1 302 Р Z

Battery Restored (Orion)

XXXX 18 3 311 Р Z

Battery Failed (Orion)

XXXX 18 1 311 Р Z

Battery Test Error (Orion)

XXXX 18 1 309 Р Z

Overvoltage (Orion)

XXXX 18 1 312 Р Z

Power Restored (Orion)

XXXX 18 3 312 Р Z

Charger Failed (Orion)

XXXX 18 1 319 Р Z

Charger Restored (Orion)

XXXX 18 3 319 Р Z

Fire Equipment Failed (Orion)

XXXX 18 1 380 Р Z

Fire Equipment Restored (Orion)

XXXX 18 3 380 Р Z

Pump On (Orion)

XXXX 18 1 205 Р Z

Pump Off (Orion)

XXXX 18 3 205 Р Z

Service Required (Orion)

XXXX 18 1 393 Р Z

Fire Equipment Test (Orion)

XXXX 18 1 607 Р Z

Test Quitted (Orion)

XXXX 18 3 607 Р Z

Substitution (Orion)

XXXX 18 1 339 Р Z

Door Forced Open (Orion)

XXXX 18 1 426 Р Z

Door Restored (Orion)

XXXX 18 3 426 Р Z

Door Held Open (Orion)

XXXX 18 1 426 Р Z

Test Error (Orion)

XXXX 18 1 343 Р Z

Alarm Test (Orion)

XXXX 18 1 611 Р Z

Subscriber Communication Fault

(Orion)

XXXX 18 1 351 Р Z

Communication Restored (Orion)

XXXX 18 3 351 Р Z

Leak Alarm (Orion)

XXXX 18 1 154 Р Z

Leakage Repaired (Orion)

XXXX 18 3 154 Р Z

Auto On (Orion)

XXXX 18 1 221 Р Z

Auto Off (Orion)

XXXX 18 3 221 Р Z

Discharge (Orion)

XXXX 18 1 222 Р Z

No-Pulse Release (Orion)

XXXX 18 1 223 Р Z

Release Failed (Orion)

XXXX 18 1 225 Р Z

Inhibited (Orion)

XXXX 18 1 226 Р Z

Abort (Orion)

XXXX 18 1 227 Р Z

Pressure Switch Failed (Orion)

XXXX 18 1 230 Р Z

Pressure Signal (Orion)

XXXX 18 1 224 Р Z

Pre-Discharge Delay (Orion)

XXXX 18 1 229 Р Z

Released (Orion)

XXXX 18 1 228 Р Z

Fire 2 Alarm (Orion)

XXXX 18 1 119 Р Z

Voice Alarm Activated (Orion)

XXXX 18 1 231 Р Z

Voice Alarm Stopped (Orion)

XXXX 18 3 231 Р Z

Noise (Orion)

XXXX 18 1 394 Р Z

Noise Removed (Orion)

XXXX 18 3 394 Р Z

Actuator Failed (Orion)

XXXX 18 1 165 Р Z

Actuator Error (Orion)

XXXX 18 1 170 Р Z

Actuator in Initial Position (Orion)

XXXX 18 3 164 Р Z

Actuator in Operating Position

(Orion)

XXXX 18 1 164 Р Z

Manual Test (Orion)

XXXX 18 1 614 Р Z

48

APPENDIX B. USER’S SMS

Default Notification List

Notification In Latin In Cyrillic

Disarmed DISARMED СНЯТ
Armed ARMED ВЗЯТ
Arming Failed FAULT НЕВЗЯТ
Wrong Code (is generated after presenting
three unknown credentials)

REFUSE ДОСТУП ОТКЛОНЕН

Patrol Check DETAIL ОТМЕТКА НАРЯДА
Alarm Loop Open Circuit Failure BREAK ОБРЫВ
Alarm Loop Short Circuit Failure SHORT КОРОТКОЕ ЗАМЫКАНИЕ
Fire Alarm FIRE ПОЖАР
Fire Prealarm (Orion) ATTENTION ВНИМАНИЕ!
Intrusion Alarm ALARM ТРЕВОГА
Panic Alarm PANIC НАПАДЕНИЕ
Entrance Alarm ENTRY ALARM ТРЕВОГА ВХОДА
Power Failure (below 11 V or above 16 V) DC TROUBLE НЕИСПР ПИТАН
Power Restored DC OK ПИТАНИЕ В НОРМЕ
AC Power Failed AC LOW НАРУШ ОСН ПИТАН
AC Power Restored AC OK ВОССТ ОСН ПИТАН
Tamper Alarm OPEN ВСКРЫТИЕ КОРПУСА
Tamper Restored CLOSE ЗАКРЫТИЕ КОРПУСА
Device Restart RESET СБРОС
Polling Loop Failure (Orion) TROUBLE 2WIRE НЕИСПРАВНОСТЬ ДПЛС
Polling Loop Restored (Orion) RESET 2WIRE ВОССТАНОВЛ ДПЛС
Output Circuit Failure (Orion) RELEY TROUBLE НЕИСПР ЦЕПИ ВЫХ
Output Circuit Restored (Orion) RELEY RESET ВОССТАН ЦЕПИ ВЫХ
Device Disconnected (Orion) DISCONNECT НАРУШЕНИЕ СВЯЗИ
Device Found (Orion) CONNECT ВОССТАНОВЛ СВЯЗИ
Programming Started PROG PART ПРОГРАММИРОВАНИЕ
TEST (only states of own alarm loops are
transmitted in the notification)

TEST STATUS ARMED
or STATUS DISARMED

ТЕСТ СОСТОЯНИЕ ВЗЯТ

or СОСТОЯНИЕ СНЯТ
Alarm Loop State (is generated as a re­sponse to a Request Armed command)

STATUS ARMED
or STATUS DISARMED

СОСТОЯНИЕ ВЗЯТ

or СОСТОЯНИЕ СНЯТ

In the Standalone Mode the events are transmitted with the number of an alarm loop:
– Object Name, DD-MM (optional) HH:MM, Event, Alarm Loop, Object Description (optional)
– Object Name, DD-MM (optional) HH:MM, Event, User Number, User Description (optional)
For the modes Slave 1, Slave 2, Master the notifications are transmitted with the number of partition and the
number of zone:
– Object Name, DD-MM (optional) HH:MM, Event, Partition, Zone, Object Description (optional)
– Object Name, DD-MM (optional) HH:MM, Event, Partition, User Number, User Description (optional)

49

APPENDIX C. EGIDA-2 SMS

Notification

Egida

-2

Local Mode

Egida

-2

Slave 1/2, Master Mode

Disarmed

DISARMED S USER N DISARMED PART P USER

N

Armed

ARMED S USER

N

ARMED PART P USER

N

Arming Failed

FAULT

S

FAULT PART P ZONA

Z

Wrong Code
(is generated after presenting three
unknown credentials)

REFUSE -

Patrol Check DETAIL DETAIL
Alarm Loop Open Circuit Failure

TRUBLE

S

TROUBLE PART P ZONA

Z

Alarm Loop Short Circuit Failure

TRUBLE

S

TROUBLE PART P ZONA

Z

Fire Alarm

FIRE

S

FIRE PART P ZONA

Z

Fire Prealarm (Orion) -

ATTENTION PART P ZONA

Z

Intrusion Alarm

ALARM

S

ALARM PART P ZONA

Z

Panic Alarm

PANIC

S

PANIC PART P ZONA

Z

Entrance Alarm

ENTRY ALARM

S

ENTRY ALARM PART P ZONE

Z

Power Failed (below 11V or above
16 V)

DC LOW

DC LOW PART P ZONE Z

Power Restored DC OK

DC OK PART P ZONE

Z

AC Power Failed AC LOW

AC LOW PART P ZONE

Z

AC Power Restored AC OK

AC OK PART P ZONE

Z

Tamper Alarm OPEN

OPEN PART P ZONE

Z

Tamper Restored CLOSE

CLOSE PART P ZONE

Z

Device Restart RESET

RESET PART P ZONE

Z

Polling Loop Failure (Orion) -

TROUBLE 2WIRE PART

P

Polling Loop Restored (Orion) -

RESET 2WIRE PART

P

Output Circuit Failure
(Orion)

-

RELEY TROUBLE PART P

Output Circuit Restored
(Orion)

-

RELEY RESET PART P

Device Disconnected
(Orion)

-

DISCONNECT PART P

Device Found (Orion) -

CONNECT PART

P

Programming Started PROG

PROG PART

P

TEST (only states of own alarm
loops are transmitted in the notifica­tion)

-

TEST
STATUS ARMED Z

or STATUS DISARMED
Alarm Loop State (is generated as
a response to a Request Armed
command)

-

STATUS ARMED ZONE Z

or STATUS DISARMED

Where:

• S is for the number of the alarm loop

• P is for the number of the partition

• D is for the address of the device

• Z is for the number of the zone

50

APPENDIX D. EGIDA-3 SMS

Notification SMS Event Source

Disarmed F99 IXXXX M242 Partition/UO-4S Internal Alarm Loop
Armed F99 IXXXX M241 Partition/UO-4S Internal Alarm Loop
Arming Failed F99 IXXXX M17 Zone/UO-4S Internal Alarm Loop
Wrong Code F99 IXXXX M26 Reader
Patrol Check F99 IXXXX M223 UO-4S
Open Circuit Failure F99 IXXXX M45 Zone/UO-4S Internal Alarm Loop
Short Circuit Failure F99 IXXXX M214 Zone/UO-4S Internal Alarm Loop
Fire Alarm F99 IXXXX M37 Zone/UO-4S Internal Alarm Loop
Fire Prealarm (Orion) F99 IXXXX M44 Zone
Intrusion Alarm F99 IXXXX M3 Zone/UO-4S Internal Alarm Loop
Panic Alarm F99 IXXXX M58 Zone/UO-4S Internal Alarm Loop
Entrance Alarm F99 IXXXX M118 Zone/UO-4S Internal Alarm Loop
Power Failed F99 IXXXX M198 Zone / Device
Power Restored F99 IXXXX M199 Zone / Device
AC Power Failed F99 IXXXX M2 Zone / Device
AC Power Restored F99 IXXXX M1 Zone / Device
Tamper Alarm F99 IXXXX M149 Zone / Device
Tamper Restored F99 IXXXX M152 Zone / Device
Device Restart F99 IXXXX M203 Device
Polling Loop Failure (Orion) (increased

polling loop voltage)

F99 IXXXX M222

Device

Polling Loop Restored (Orion) F99 IXXXX M47 Device
Output Open Circuit Failure F99 IXXXX M112 Zone
Output Short Circuit Failure F99 IXXXX M122 Zone
Output Circuit Restored F99 IXXXX M123 Zone
Device Disconnected (Orion) F99 IXXXX M250 Device
Device Connected (Orion) F99 IXXXX M251 Device
Starting Programming Mode F99 IXXXX M84 Device
RS-485 Communication Fault F99 IXXXX M217 Device
RS-485 Communication Restored F99 IXXXX M218 Device
Polling Loop Short Circuit Failure F99 IXXXX M215 Device
Alarm Loop Disconnected F99 IXXXX M187 Zone
Alarm Loop Connected F99 IXXXX M188 Zone
Output Disconnected F99 IXXXX M126 Zone
Output Connected F99 IXXXX M127 Zone
High Temperature F99 IXXXX M76 Zone
Low Temperature F99 IXXXX M206 Zone

51

Notification SMS Event Source

Normal Temperature F99 IXXXX M78 Zone
High Level F99 IXXXX M74 Zone
Low Level F99 IXXXX M71 Zone
Too High Level F99 IXXXX M75 Zone
Too Low Level F99 IXXXX M77 Zone
Normal Level F99 IXXXX M72 Zone
Auxiliary Input Alarm F99 IXXXX M35 Zone
Auxiliary Input Restored F99 IXXXX M36 Zone
Low Battery F99 IXXXX M211 Device / Zone
Battery Failed F99 IXXXX M202 Device / Zone
Battery Restored F99 IXXXX M200 Device / Zone
Battery Test Error F99 IXXXX M205 Device / Zone
Power Supply Overload F99 IXXXX M194 Device / Zone
Overload Repaired F99 IXXXX M195 Device / Zone
Charger Failed F99 IXXXX M196 Device / Zone
Charger Restored F99 IXXXX M197 Device / Zone
Fire Equipment Failed F99 IXXXX M41 Device / Zone
Fire Equipment Restored F99 IXXXX M39 Zone
Pump On F99 IXXXX M130 Zone / Output
Pump Off F99 IXXXX M131 Zone / Output
Service Required F99 IXXXX M204 Zone / Output
Alarm Test F99 IXXXX M19 Zone
Fire Equipment Test Started F99 IXXXX M20 Device / Zone
Test Quitted F99 IXXXX M21 Device / Zone
Configuration Error F99 IXXXX M165 Zone
Door Forced Open F99 IXXXX M27 Reader
Door Restored F99 IXXXX M31 Reader
Door Held Open F99 IXXXX M33 Reader
Access Denied F99 IXXXX M29 Reader

Test F99 IXXXX M255 Device

Subscriber Communication Fault (Orion)

F99 IXXXX M90 Subscriber

Communication Restored (Orion)

F99 IXXXX M91 Subscriber

Leak Alarm (Orion)

F99 IXXXX M79 Zone

Leakage Repaired (Orion)

F99 IXXXX M80 Zone

Auto On (Orion)

F99 IXXXX M148 Zone

Auto Off (Orion)

F99 IXXXX M142 Zone

Discharge (Orion)

F99 IXXXX M146 Zone

No-Pulse Error (Orion)

F99 IXXXX M145 Zone

Release Failed (Orion)

F99 IXXXX M139 Zone

52

Notification SMS Event Source

Inhibited (Orion)

F99 IXXXX M147 Zone

Abort (Orion)

F99 IXXXX M143 Zone

Pressure Switch Failed (Orion)

F99 IXXXX M221 Zone

Pressure Signal (Orion)

F99 IXXXX M220 Zone

Pre-Discharge Delay (Orion)

F99 IXXXX M141 Zone

Released (Orion)

F99 IXXXX M144 Zone

Fire 2 Alarm (Orion)

F99 IXXXX M40 Zone

Voice Alarm Activated (Orion)

F99 IXXXX M150 Zone

Voice Alarm Stopped (Orion)

F99 IXXXX M151 Zone

Noise (Orion)

F99 IXXXX M4 Zone

Noise Removed (Orion)

F99 IXXXX M6 Zone

Actuator Failed (Orion)

F99 IXXXX M155 Zone

Actuator Error (Orion)

F99 IXXXX M156 Zone

Actuator in Initial Position (Orion)

F99 IXXXX M154 Zone

Actuator in Operating Position

(Orion)

F99 IXXXX M153

Zone

Manual Test (Orion)

F99 IXXXX M140 Zone

53

APPENDIX E. VOICE MESSAGES

List of Default Voice Messages

Notification Voice Message

Disarmed Снят с охраны раздел P пользователь N
Armed Взятие под охрану раздел P пользователь N
Arming Failed Не взятие раздел P зона Z [пользователь N]
Wrong Code

(generated after three presenting of unknown
credentials)

Доступ отклонен прибор D

Patrol Check Отметка наряда прибор D
Open Circuit Failure Обрыв раздел P зона Z
Short Circuit Failure Короткое замыкание раздел P зона Z
Fire Alarm Пожар раздел P зона Z
Fire Prealarm (Orion) Опасность пожара раздел P зона Z
Intrusion Alarm Тревога раздел P зона Z
Panic Alarm Нападение раздел P зона Z
Entrance Alarm Тревога входа раздел P зона Z
Power Failed (is below 11 V or exceeds 16 V) Неисправность питания раздел P зона Z
Power Restored Восстановление резервного питания прибор D
AC Power Failed Нарушение основного питания раздел P зона Z
AC Power Restored Восстановление основного питания раздел P зона Z
Tamper Alarm Взлом корпуса раздел P зона Z
Tamper Restored Закрытие корпуса раздел P зона Z
Device Reset Сброс раздел P зона Z
Polling Loop Failure (Orion) Нарушение ДПЛС раздел P зона Z
Polling Loop Restored (Orion) Восстановление ДПЛС раздел P зона Z
Output Circuit Failure (Orion) Нарушение выхода раздел P зона Z
Output Circuit Restored (Orion) Восстановление выхода раздел P зона Z
Communication Fault (Orion) Нарушение связи раздел P зона Z
Communication Restored (Orion) Восстановление связи раздел P зона Z
Programming Started Программирование раздел P зона Z [пользователь N]
TEST (only states of own alarm loops are

transmitted in the notification)

--------------

Alarm Loop State (is generated as a response
to a Request Armed command)

--------------

Where:

• P is for the number of the partition

• D is for the address of the device

• Z is for the number of the zone

• N is for the user number

54

MANUFACTURER DATA

Made by the Bolid Company, Russia.

4 Pionerskaya Str., Korolev, Moscow Oblast, 141070, Russia

Tel./Fax: [phone] (multichannel), 777-40-20, 516-93-72

E-mail:

[e-mail],

http://

bolid.ru.

Technical Support: [e-mail].