Bogen FMHAR8, SGHD8, BBFM6 Installation Manual
© 2005 Bogen Communications, Inc.
All rights reserved.
Specifications subject to change without notice.
54-2136-01C 1211
Wiremold® Knockouts
(only on BBSM6)
Components
Assembly
Models BBSM6, BBFM6, FMHAR8, & SGHD8
For use with FMH15T horn loudspeaker
1) Place gasket supplied with FMH15T onto FMHAR8 Adapter
Ring over the studs. Then mount FMH15T to FMHAR8
Adapter Ring, sliding flange hole over adapter ring studs and
secure with nuts supplied with adapter ring.
2) Slide FMH15T/FMHAR8 assembly over studs in SGHD8
Grille and secure with nuts supplied with grille.
3) Mount BBSM6 or BBFM6 enclosure as necessary.
4) Use 4 white security screws and tool supplied with SGHD8
Grille to mount the speaker/grille assembly onto the enclosure.
For use with 8" cone loudspeakers
1) Slide 8" cone speaker over studs in SGHD8 Grille and
secure with nuts supplied with grille.
2) Mount BBSM6 or BBFM6 enclosure as necessary.
3) Use 4 white security screws and tool supplied with SGHD8
Grille to mount the speaker/grille assembly onto the enclosure.
Wiremold®is a Registered Trademark of Wiremold/Legrand
Wiremold® Knockouts
(only on BBSM6)
50 Spring Street, Ramsey, NJ 07446, U.S.A.
201-934-8500; Fax: 201-934-9832
www.bogen.com
The BBSM6, BBFM6, FMHAR8, and SGHD8 are warranted to be free from defects in material or workmanship for two (2) years from the date of sale to the original
purchaser. Any part of the product covered by this warranty that, with normal installation and use, becomes defective will be repaired or replaced by Bogen,
at our option, provided the product is shipped insured and prepaid to: Bogen Factory Service Department, 50 Spring Street, Ramsey, NJ 07446, USA. The product
will be returned to you freight prepaid. This warranty does not extend to any of our products that have been subjected to abuse, misuse, improper storage,
neglect, accident, improper installation or have been modified or repaired or altered in any manner whatsoever, or where the serial number or date code has been
removed or defaced.
THE FOREGOING LIMITED WARRANTY IS BOGEN'S SOLE AND EXCLUSIVE WARRANTY AND THE PURCHASER'S SOLE AND EXCLUSIVE REMEDY.
BOGEN MAKES NO OTHER WARRANTIES OF ANY KIND, EITHER EXPRESS OR IMPLIED, AND ALL IMPLIED WARRANTIES OF MERCHANTABILITY OR
FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY DISCLAIMED AND EXCLUDED TO THE MAXIMUM EXTENT ALLOWABLE BY LAW. Bogen's
liability arising out of the manufacture, sale or supplying of products or their use or disposition, whether based upon warranty, contract, tort or otherwise, shall be
limited to the price of the product. IN NO EVENT SHALL BOGEN BE LIABLE FOR SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES (INCLUDING,
BUT NOT LIMITED TO, LOSS OF PROFITS, LOSS OF DATA OR LOSS OF USE DAMAGES) ARISING OUT OF THE MANUFACTURE, SALE OR SUPPLYING
OF PRODUCTS, EVEN IF BOGEN HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES OR LOSSES. Some States do not allow the exclusion
or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. This warranty gives you specific legal rights, and
you may also have other rights which vary from State to State.
Products that are out of warranty will also be repaired by the Bogen Factory Service Department -- same address as above or call 201-934-8500. The parts and
labor involved in these repairs are warranted for 90 days when repaired by the Bogen Factory Service Department. All shipping charges in addition to parts and
labor charges will be at the owner's expense. All returns require a Return Authorization number.
7/22/2008
Limited Warranty; Exclusion of Certain Damages
Components
BBSM6
Surface-Mount Enclosure
• White, heavy gauge, steel with
single knockout on back
• 11" W x 11" H x 6" D
SGHD8
Grille
• Heavy duty, square, white, cast
aluminum with finely perforated
mesh insert
• For use with BBSM6 or BBFM6
• 11" W x 11" H x 1/2" D
BBFM6
Flush-Mount Enclosure
• Black, heavy gauge, steel with
knockout on each vertical side
• 9-7/8" W x 9-7/8" H x 6" D
FMHAR8
Adapter Ring
• Fits FMH15T to 8" speaker
opening of SGHD8 grille
Loading...