Bogen OPS1 User Manual

© 2003 Bogen Communications, Inc. All rights reserved. Specifications subject to change without notice. 54-2090-01A 0302 Printed in Taiwan.
Orbit Pendant Speaker
OPS1
Installation and Use Manual
Product Description
All NEAR products include similar technical and design aspects that are unique to the market. NEAR invented and patented the "spiderless" woofer (MLS™), which features a high-gauss ferrofluid to guide the voice coil through the magnetic field.The benefits over conventional woofers with cloth spiders are several, including the abil­ity to constantly adjust voice coil alignment, extend linear excursion, and the most efficient path for cooling the voice coil.
In addition, the use of metal-alloy cone structures provides several benefits over the usual paper or plastic cone, such as elimination of cone flex or "break-up" in the operating ranges, additional thermal path for the voice coil to stay cool, and an extremely stable cone structure unaffected by the environment.
The NEAR OPS1 pendant loudspeaker is a full-range, wide dispersion system pro­viding overhead sound coverage where ceiling structures are high but the sound needs to be closer to the audience/listener.An optional cable kit (CK10) suitable for safety or main drop cable is available.
Settings for both 70V and 100V high-impedance systems, as well as a low-impedance (16-ohm) position, are provided.Also, a conversion chart for speaker use in 25V sys­tems is provided in this manual.
All ORBIT models feature a removable snap-lock input connector, providing easy wire connection for input as well as loop-through to the next speaker.
Product Diagrams
OPS1 Front Drawing
1.Tap Selection Switch
2. Coaxial Driver Assembly
3. Grille Retention Slot
4. Bass Tuning Vent (x2)
5. Perforated Steel Grille
OPS1 Rear Drawing
1. Snap-Lock Input Connector
2. Suspension Points (x3)
3. Safety Cable Suspension Point
Package Contents
(1) Orbit Pendant Speaker
(1) Manual
(1) Quick-Snap Clip
(1) Snap-Lock Input Connector
(3) Forged Eye Bolts
(3) Nuts
(3) Suspension Cables
OPS1 Front Drawing
OPS1 Rear Drawing
1
Installation
If the power level is known, then select it using the front-mounted selector switch prior to installing the OPS1. See section Selecting Power Levels.
SUSPENSION CABLE ASSEMBLY
1. Screw nuts onto the eye bolts all the way to the flange.
2. Screw in eye bolts with captured cable sec­tions in to the three suspension points. Do not overtighten.
3. Snap loops of free end of cable sections into quick-snap clip.
4. Connect quick-snap clip to anchor point or drop cable. Bogen’s CK10 cable kit is suit­able for use as the drop cable.
SAFETY CABLE
The OPS1 includes a safety cable suspension point for extra protection.
The thread of the suspension point is a 1/4-20" x 1/2" thread. Bogen offers a cable kit as an optional accessory (CK10) that is suitable for use as the safety cable.
2
IMPORTANT
The anchor point, drop cable, and hardware used to hang the speaker must be able to support the speaker’s weight under all conditions. IF YOU ARE NOT SURE OF THE PROPER CAPACITY OF THESE ITEMS TO USE, CONSULT A STRUCTURAL ENGINEER. Mount only one speaker per supplied quick-snap clip.
1.
2.
3.
4.
Speaker Wiring
Wiring is terminated at a snap-lock input con­nector. There are two positive and two nega­tive terminals to accommodate daisy chaining of speakers in a system. All wiring should be done prior to installation and then plugged into the rear of the OPS1.
DAISY CHAINING
The OPS1’s snap-lock input connector allows for easy daisy chaining of speakers by provid­ing a second terminal of each polarity. Refer to the figures for proper wiring for daisy chaining of terminals.
SPEAKER PHASING
Keep the same polarity terminals wired together to ensure correct phasing. In order to provide the best possible sound, all of the speakers in a system need to be push­ing out and pulling in at the same time.
If the connections to one speaker in a system are reversed from the others, that speaker’s movement will be out of sync with the other speakers.This will result in a loss of low frequency response and will effect the overall performance of the sys­tem.
3
Selecting Power Levels
The front-mounted selector switch is used to set the appropriate power level or impedance for your system. Using a small flat-blade screw­driver, turn the knob until the slot points to the power level you require.
70V/100V SYSTEMS
Both power setting scales for 70V and 100V sys­tems are labeled on the speakers. On the 100V scale, the last position clockwise is marked with a (not available) symbol.Do not use this posi­tion in 100V systems.
16
SYSTEMS
The fully counterclockwise position of the setting switch is the 16-ohm position.This setting is suitable for use with low-impedance amplifiers that typically support 4- or 8-ohm speakers.The speaker’s higher, 16-ohm impedance makes it easier to combine multiple speakers into series - parallel networks while keeping the total system impedance at a level suitable for low-impedance amplifiers.
25V SYSTEMS
The OPS1 will operate on 25V systems, but at reduced power levels. The chart to the right shows the conversion from a 70V power setting to the actual 25V power level.
Accessory
CK10 (CABLE KIT, 10’)
The CK10 is a 10-foot cable with one looped end, a forged eye bolt (with 1/4-20" x 1/2" thread), and an adjustable cable clamp. It is suitable for use as a drop cable or
safety cable.
25V Conversion Table
70V Setting
32W 4W
25V Power
16W
2W
8W
1W
4W
1/2W
2W
1/4W
1W 1/8W
16
39W
4
Specifications
5
SPECIFICATIONS
OPS1
Frequency Response (-10 dB)
*
60 Hz to 19 kHz
LF Driver
6-1/2
" MDT Metal-Alloy Cone
(MLS Voice Coil Centering System)
HF Driver 20 mm (3/4") Polycarbonate Dome
Sensitivity (1W/1M) 89.5 dBspl (Average 100 Hz - 10 kHz)
Impedance Ratings
Low (16 ohms) / High (70V/100V)
Power Input (Max.)
100W @ 16 ohms; 32W @ 70V/100V
Power Settings (in watts)
70V: 32, 16, 8, 4, 2, 1
100V: 32, 16, 8, 4, 2
Enclosure Material Fire-rated (94VO) ABS
Grille Material Powder-Coated Perforated Metal
Terminations 4 Terminal Snap-Lock Input Connector
Product Weight
10 lb.
Speaker Dimensions
15" dia. x 9-1/4" D
Included Accessories
(3) Suspension Cables; (3) Forged Eye Bolts; (3) Nuts;
(1) Quick-Snap Clip; (1) Snap-Lock Input Connector
Optional Accessories
Cable Kit (CK10)
Enclosure Finish & Color Textured White or Black
*
Free Space Response, 16-ohm input
† Front panel, switch-selected.
50 Spring Street, Ramsey, NJ 07446, U.S.A.
Tel. 201-934-8500, Fax: 201-934-9832, www.bogen.com
Warranty
Orbit Pendant Speakers are warranted to be free from defects in material or work­manship provided that the product has not been subjected to abuse or accident or altered in any way for five (5) years from the date of sale to the original purchaser.Any part of the product covered by this warranty that, with normal installation and use, becomes defective will be repaired or replaced by Bogen, at our option, provided the product is shipped insured and prepaid to: Bogen Factory Service Department, 50 Spring Street, Ramsey,NJ 07446, USA.The product will be returned to you freight pre­paid.This warranty does not extend to any of our products that have been subjected to misuse, improper storage, neglect,accident,improper installation or have been mod­ified or repaired in any manner that Bogen believes may affect the reliability of the product, or where the serial number or date code has been removed or defaced.
THE FOREGOING LIMITED WARRANTY IS BOGEN’S SOLE AND EXCLUSIVE WARRANTY AND THE PURCHASER’S SOLE AND EXCLU­SIVE REMEDY. BOGEN MAKES NO OTHER WARRANTIES OF ANY KIND, EITHER EXPRESS OR IMPLIED,AND ALL IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY DISCLAIMED AND EXCLUDED. Bogen's liability arising out of
the manufacture, sale or supplying of products or their use or disposition, whether based upon warranty, contract, tort or otherwise, shall be limited to the price of the product. In no event shall Bogen be liable for special, incidental or consequential dam­ages (including, but not limited to, loss of profits, loss of data or loss of use damages) arising out of the manufacture, sale or supplying of products, even if Bogen has been advised of the possibility of such damages or losses.
Products that are out of warranty will also be repaired by the Bogen Factory Service Department -- same address as above or call 201-934-8500. The parts and labor involved in these repairs are warranted for 90 days when repaired by the Bogen Factory Service Department. All shipping charges in addition to parts and labor charges will be at the owner's expense.
Loading...